Whirlpool CAWD 125 (EX) Mode d'emploi

Marque: Whirlpool

Modèle: CAWD 125 (EX)

Catégorie: Machines à laver

Taper: Mode d'emploi

English,1

 This symbol reminds you to read this instruction manual.

Contents

Installation, 2-3-4-5-6-7

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Instructions for the fitter

Description of the washer-dryer and

starting a wash cycle, 8-9

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 10

Table of wash cycles

Personalisation, 11

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 12

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 13

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 14

Cutting off the water or electricity supply

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 15

Service, 16

CAWD 125

Instructions for use

WASHER DRYER

Français,17

, 33

, 49

Installation

 This instruction manual should be kept in a safe

place for future reference. If the washer-dryer is sold,

transferred or moved, make sure that the instruction

manual remains with the machine so that the new

owner is able to familiarise himself/herself with its

operation and features.

 Read these instructions carefully: they contain vital

information relating to the safe installation and

operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washer-dryer from its packaging.

2. Make sure that the washer-dryer has not been

damaged during the transportation process. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

3. Remove the 4

protective screws (used

during transportation) and

the rubber washer with

the corresponding

spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need

them again if the washer-dryer needs to be moved to

another location.

 Packaging materials should not be used as toys for

children.

Levelling

1. Install the washer-dryer on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or anything else.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or loosening

the adjustable front feet

(see figure); the angle of

inclination, measured in

relation to the worktop,

must not exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive noise

and prevent it from shifting while it is operating. If it is

placed on carpet or a rug, adjust the feet in such a

way as to allow a sufficient ventilation space

underneath the washer-dryer.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to a

cold water tab using a ¾

gas threaded connection

(see figure).

Before performing the

connection, allow the

water to run freely until it

is perfectly clear.

2. Connect the inlet hose

to the washer-dryer by

screwing it onto the

corresponding water inlet

of the appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical details table (see

next page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand hoses.

 Use the ones supplied with the machine.

65 - 100 cm

Connecting the drain hose

Connect the drain hose,

without bending it, to a

drainage duct or a wall

drain located at a height

between 65 and 100 cm

from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not

be underwater.

 We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electric connection

Before plugging the appliance into the mains socket,

make sure that:

 the socket is earthed and in compliance with the

applicable law;

 the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

 the supply voltage is included within the values i

ndicated on the Technical details table

(see page 5);

 the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is lost,

the plug must not be used until a replacement is

obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking

or the colour that is embossed in words on the base

of the plug. Replacements can be obtained directly

from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable

through partitions, units etc., please ensure that

either:

the plug is replaced by a fused 13 ampere re-

wearable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with BS

5733) which is accessible without moving the

appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

As the colours of the wires in the lead may not

correspond with the coloured markings identifyng the

terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E or

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the

plug by cutting the mains cable as close as possible

to the plug body and dispose of it as described above.

 The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to leave

it exposed to rain and thunderstorms.

 When the washing machine is installed, the mains

socket must be within easy reach.

 Do not use extensions or multiple sockets.

 The power supply cable must never be bent or

dangerously compressed.

 The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 1.

Technical data

Model

CAWD 125

Dimensions

width 59,5 cm

height 81,5 cm

depth 54,5 cm

Capacity

from 1 to 7 kg for the wash programme;

from 1 to 5 kg for the drying programme

Electrical

connections

please refer to the technical data plate

fixed to the machine

Wate r

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1200 rotations per minute

Energy rated

programmes

according to

EN 50229

Wash:

programme 6; temperature 60°C;

using a load of 7 kg.

Drying:

first drying cycle performed with a

2 kg load, by selecting the dryness level.

The second drying cycle is performed with a

5 kg load, by selecting the dryness level.

This appliance conforms to the following

EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2006/95/EC (Low Voltage)

- 2002/96/EC

Instructions for the fitter

Mounting the wooden panel onto the door and

inserting the machine into cabinets:

In the case where the machine must be shipped for final

installation after the wooden panel has been mounted, we

suggest leaving it in its original packaging. The packaging

was designed to make it possible to mount the wooden

panel onto the machine without removing it completely

(see figures below).

The wooden panel that covers the face of the machine

must not be less than 18 mm in thickness and can be

hinged on either the right or left. For the sake of

practicality when using the machine, we recommend that

the panel be hinged on the same side as the door for the

machine itself - the left.

Tur seite

Door Mounting Accessories (Fig. 1-2-3-4-5).

Fig. 1

N° 2 Hinges

N° 1 Magnet N° 1 Magnet plate

N° 1 Rubber plug

N° 2 Hinge Supports

N° 4 Spacers

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 4/B

- No. 6 type A self-threading screws, l =13 mm.

- No. 2 type B metric, countersunk screws, l =25; for

fastening the magnet plate to the cabinet.

- No. 4 type C metric screws, l =15 mm; for mounting the

hinge supports to the cabinet.

- No. 4 type D metric screws, l =7 mm; for mounting the

hinges on the supports.

Mounting the Parts onto the Face of the Machine.

- Fit the hinge supports to the appliance front panel,

positioning the hole marked with an arrow in fig. 1 so that it

is on the inner side of the front panel. Fit a spacer (fig. 4/B)

between the surfaces using type C screws.

- Fit the magnet plate at the top of the opposite side,

using type B screws to fix two spacers (fig. 4/B) between

the plate and the surface.

Using the Drilling Template.

- To trace the positions of the holes on the left-hand side of

the panel, align the drilling template to the top left side of

the panel using the lines traced on the extremities as a

reference.

- To trace the positions of the holes on the right-hand side

of the panel, align the drilling template to the top right side

of the panel.

- Use an appropriately sized router to mill the holes for the

two hinges, the rubber plug and the magnet.

Mounding the Parts onto the Wooden Panel (Door).

- Insert the hinges into the holes (the movable part of the

hinge must be positioned facing away from the panel) and

fasten them with the 4 type A screws.

- Insert the magnet into the top hole on the opposite side

of the hinges and fasten it with the two type B screws.

- Insert the rubber plug into the bottom hole.

The panel is now ready to be mounted onto the machine.

Mounting the Panel into the machine.

Insert the nib of the hinge (indicated by the arrow in fig. 2)

into the hole for the hinge and push the panel towards the

front of the machine. Fasten the two hinges with the type

D screws.

Fastening the plinth guide.

If the machine is installed at the end of a set of modular

cabinets, mount either one or both of the guides for the

base molding (as shown in fig. 8). Adjust them for depth

based on the position of the base molding, and, if

necessary, fasten the base to the guides (fig. 9).

This is how to assemble the plinth guide (fig. 8):

Fasten angle P using screw R, insert plinth guide Q into the

special slot and once it is in the desired position, lock it in

place using angle P and screw R.

Inserting the machine into the Cabinet.

- Push the machine into the opening, aligning it with the

cabinets (fig. 6).

- Regulate the adjustable feet to raise the machine to the

appropriate height.

- To adjust the position of the wooden panel in both the

vertical and horizontal directions, use the C and D screws,

as shown in fig. 7.

Important: close the lower part of the appliance front by

ensuring that the plinth rests against the floor.

Fig. 8 Fig. 9

Accessories provided for the height adjustment.

The following can be found inside the polystyrene lid (fig. 10):

2 crossbars (G), 1 strip (M)

the following can be found inside

the appliance drum:

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

2 plinth guides (Q)

Adjusting the appliance height.

The height of the appliance can be adjusted (from 815 mm

to 835 mm), by turning the 4 feet.

Should you require the appliance to be placed higher than

the above height, you need to use the following accessories

to raise it to up to 870 mm:

the two crossbars (G); the 4 feet (H); the 4 screws (I); the 4

nuts (L) then perform the following operations (fig. 11):

remove the 4 original feet, place a crossbar G at the front of

the appliance, fastening it in place using screws I (screwing

them in where the original feet were) then insert the new feet H.

Repeat the same operation at the back of the appliance.

Now adjust feet H to raise or lower the appliance from 835

mm to 870 mm.

Once you have reached the desired height, lock nuts L onto

crossbar G.

To adjust the appliance to a height between 870 mm and

900 mm, you need to mount strip M, adjusting feet H to the

required height.

Insert the strip as follows:

loosen the three screws N situated at the front of the Top

cover of the appliance, insert strip M as shown in fig. 12,

then fasten screws N.

570

min

815

540

595

820 ÷ 900

600 min

Fig. 6 Fig. 7

Fig. 11 Fig. 12

Fig. 10

Detergent dispenser drawer: used to dispense

detergents and washing additives (see Detergents

and laundry).

ON/OFF button: switches the washer-dryer on and

off.

WASH CYCLE knob: programmes the wash cycles.

During the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to

select the available functions. The indicator light

corresponding to the selected function will remain lit.

TEMPERATURE knob: sets the temperature or the

cold wash cycle (see Personalisation).

DRYING knob: used to set the desired drying

programme (see Personalisation).

WASH CYCLE PROGRESS/DELAY TIMER

indicator light

s: used to monitor the progress of the

wash cycle.

The illuminated indicator light shows which phase is in

progress.

If the Delay Timer function has been set, the time

remaining until the wash cycle starts will be indicated

(see next page).

DOOR LOCKED indicator light: indicates whether

the door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or

temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash

orange, while the indicator light for the current wash

cycle phase will remain lit in a fixed manner. If the

DOOR LOCKED

indicator light is switched off, the

door may be opened.

To start the wash cycle from the point at which it was

interrupted, press this button again.

Standby mode

This washing machine, in compliance with new

energy saving regulations, is fitted with an automatic

standby system which is enabled after about 30

minutes if no activity is detected. Press the ON-OFF

button briefly and wait for the machine to start up

again.

Description of the washer-dryer and

starting a wash cycle

Control panel

TEMPERATURE

knob

Detergent dispenser drawer

WASH CYCLE PROGRESS/

DELAY TIMER

indicator lights

FUNCTION

buttons with

indicator lights

ON/OFF

button

SPIN SPEED

knob

DOOR

LOCKED

indicator light

START/

PAUSE

button with

indicator light

WASH CYCLE

knob

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see

Personalisation), after the wash cycle has been

started the indicator light corresponding to the

selected delay period will begin to flash:

As time passes, the remaining delay will be displayed

and the corresponding indicator light will flash:

Once the set delay has elapsed, the flashing indicator

light will switch off and the selected wash cycle will

begin.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has

begun, the indicator lights switch on one by one to

indicate which phase of the cycle is currently in progress.

Note: during the "Drain" phase, the indicator light

corresponding to the "Spin" cycle phase will illuminate.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding

indicator light will illuminate.

If the selected function is not compatible with the

programmed wash cycle, the corresponding indicator

light will flash and the function will not be activated.

If a function which is incompatible with another

function selected previously, only the most recent

selection will remain active.

Door locked indicator light

If this indicator light is on, the appliance door is locked

to prevent it from being opened accidentally; to avoid

any damage, wait for the indicator light to switch off

before you open the appliance door.

N.B. If the DELAY TIMER function is activated, the door

cannot be opened; pause the machine by pressing the

START/PAUSE button if you wish to open it.

 If the START/PAUSE indicator light (orange) flashes

rapidly at the same time as the function indicator

light, this indicates a problem has occurred (see

Troubleshooting).

Starting a wash cycle

1. Turn the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few

seconds, then only the indicator lights relative to the selected programme settings will remain lit and the START/

PAUSE indicator light will flash.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see Personalisation).

5. Set the drying cycle if necessary (see Personalisation).

6. Measure out the detergent and washing additives (see Detergents and laundry).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit

in a fixed manner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE

button and select a new cycle.

9. At the end of the wash cycle the

indicator light will switch on. The DOOR LOCKED indicator light will switch

off, indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to make

sure the drum dries completely. Switch the washer-dryer off by pressing the ON/OFF button.

Wash

Rinse

Spin

Dry

End of wash cycle

Note: as soon as a drying

level or time period has been

set, this indicator light

illuminates to indicate that

the selected wash cycle will

be followed by a drying

phase.

Specials wash cycles

Sanitizing cycle (wash cycle 6). A high-temperature hygienic wash cycle (over 60°C) which requires the use of bleach.

Pour the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled

Detergent dispenser drawer).

Goodnigt cycle (wash cycle 7). This is a silent cycle which can be run at night, when the electricity prices are lower. The

wash cycle is designed for cottons and synthetics. At the end of the cycle the machine stops while there is still water in

the drum; to spin and drain the laundry press the START/PAUSE button; alternatively the machine will perform the spin

cycle and drain the water automatically after 8 hours.

Baby cycle (wash cycle 8). This wash cycle can be used to remove the soiling typically caused by babies, while ensuring

that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The

cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect

of special disinfecting additives added to the detergent.

At the end of the wash cycle, the machine will slowly rotate the drum to prevent the formation of creases; to end the cycle

press the START/PAUSE button.

Mix 30 (wash cycle 4) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and

therefore saves both energy and time. By selecting this wash cycle (4 at 30°C), it is possible to wash different fabrics

together (except for wool and silk items), with a maximum load of 3 kg.

Mix 15 (wash cycle 5) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and

therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics

together (except for wool and silk items), with a maximum load of 1.5 kg.

Wash cycles

The information contained in the table is intended as a guide only.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 6 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 1 with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.

Wash cycles

Table of wash cycles

Description of the wash cycle

Max

temp.

(°C)

Max.

speed

(rpm)

Drying

Detergents

Max.

load

(kg)

Cycle

duration

Bleach Wash

Fabric

softener

Specials cycles

Sanitizing cycle:

Extremely soiled whites.

90° 1200

llll

7170

Sanitizing cycle (1):

Heavily soiled whites and resistant colours.

60° 1200

7 153

Goodnigt cycle:

Lightly soiled delicate colours.

40° 800 - -

4290

Baby cycle:

Heavily soiled delicate colours.

40° 800

2118

Silk/Curtains:

For garments in silk and viscose, lingerie.

30° 0 - -

155

Wool:

For wool, cashmere, etc.

40° 800

1,5 55

Daily wash cycles

Cotton:

Heavily soiled whites and resistant colours.

60° 1200

llll

7 122

Cotton (2):

Heavily soiled whites and delicate colours.

40° 1200

llll

7115

Coloured Cottons (3):

Lightly soiled whites and delicate colours.

40° 1200

llll

785

Synthetics resistents:

Heavily soiled resistant colours.

60° 800

385

Synthetics resistents:

Lightly soiled resistant colours.

40° 800

370

Mix 30':

To refresh lightly soiled garments quickly (not suitable for wool,

silk and clothes which require washing by hand).

30° 800

330

Mix 15':

To refresh lightly soiled garments quickly (not suitable for wool,

silk and clothes which require washing by hand).

30° 800

1,5 15

Partials wash cycles

Rinse - 1200

- -

736

Spin - 1200

- - - 716

Drain no spin - 0 - - - - 72

Drying cycles

Cotton drying - -

- - - 5 -

Synthetics drying - -

- - - 3 -

Wool drying - -

- - - 1,5 -

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash (

The washer-dryer will automatically prevent you from selecting a temperature which is higher than the maximum

value set for each wash cycle.

Setting the drying cycle

Turn the DRYING knob to set the desired drying type.

Two options are available:

A - Based on time: from 40 to 180 minutes.

B - Based on the how damp the clothes are once they have

been dried:

Iron

: slightly damp clothes, easy to iron.

Hanger

: dry clothes to put away.

Cupboard

: very dry clothes, recommended for towelling

and bathrobes.

If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent table),

perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them

back in the drum. At this point, follow the instructions provided for a "Drying only" cycle. Repeat this procedure

for the remainder of the load.

N.B: When the drying is complete there is a cooling period, even though the DRYING knob is in the

position.

Drying only

Turn the WASH CYCLE knob to one of the drying settings (11-12-13) according to the type of fabric, then select

the desired drying duration using the DRYING knob.

Functions

The various wash functions available with this washer-dryer will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in

conjunction with the selected wash cycle.

Delay timer

This timer delays the start time of the wash cycle by up to 9 hours.

Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time

the button is pressed, the function will be disabled.

N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it.

 This option is enabled with all programmes.

Extra rinse

By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is

particularly useful for sensitive skin.

 This function may not be used in conjunction with wash cycles 4, 5, 11, 12, 13, B, C.

Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle

duration, this function offers a high-performance wash.

 This function may not be used in conjunction with wash cycles 4, 5, 6, 9, 10, 11, 12, 13, A, B, C.

1200-600

By selecting this function, reduces the spin speed.

 This function may not be used in conjunction with wash cycles 9, C, 11, 12, 13.

Personalisation

Fabric

type

Load type Max.

load

(kg)

Cupboard

dry

Henger

dry

Iron

dry

Cotton Clothing of different

sizes, Terry towels

5180170160

Synthe-

tics

Sheets, Shirts, Pyjamas,

socks, etc.

3180170160

Wool Knitwear, Pullovers, etc.

1,5 150 140 130

Table of Drying times (guideline values)

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance

and contribute to environmental pollution.

 Do not use hand washing detergents because these

create too much foam.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

compartment 1: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 3: Bleach

Bleach cycle

Bleaching may only be performed in conjunction with

wash cycles 1, 2, 6.

Pour the bleach into extra compartment 3; pour the

detergent and softener into the corresponding

compartments, then select one of the

abovementioned wash cycles.

This option is recommended only for very soiled

cotton garments.

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites.

 Empty all garment pockets and check the buttons.

 Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 7 kg

Synthetic fabrics: max. 3 kg

Delicate fabrics: max. 2 kg

Wool: max. 1.5 kg

MAX

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Silk: use special wash cycle 9 to wash all silk

garments. We recommend the use of special

detergent which has been designed to wash delicate

clothes.

Curtains: these should be folded and placed inside

the bag provided. Use wash cycle 9.

Wool: Ariston is the only washer-dryer manufacturer

to have been awarded the prestigious Woolmark

Platinum Care endorsement (M.0508) by the

Woolmark Company, which means that all woollen

garments may be washed in the washer-dryer, even

those which state hand wash only

on the label.

Wash cycle 10 therefore offers complete peace of

mind when washing woollen garments in the washer-

dryer (max. load 1.5 kg) and guarantees optimal

performance.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly

greater than the washing rotation speed. If, after

several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the

load is excessively unbalanced, the washer-dryer

performs the distribution process instead of spinning.

To encourage improved load distribution and balance,

we recommend small and large garments are mixed

in the load.

Anti-crease

This function interrupts the wash programme, and the

washing is left to soak in water before the appliance

is drained.

It can only be used with programme 9 (Silk/Curtains)

and helps to prevent the formation of creases.

To complete the cycle press the START/PAUSE

button.

Precautions and tips

 This washer-dryer was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons

and must therefore be read carefully.

General safety

 This appliance was designed for domestic use only.

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with the

appliance.

- Do not dry unwashed items in the tumble dryer.

- Items that have been soiled with substances such

as cooking oil, acetone, alcohol, petrol, kerosene,

spot removers, turpentine, waxes and wax removers

should be washed in hot water with an extra

amount of detergent before being dried in the

tumble dryer.

- Items such as foam rubber (latex foam), shower

caps, waterproof textiles, rubber backed articles

and clothes or pillows fitted with foam rubber pads

should not be dried in the tumble dryer.

- Fabric softeners, or similar products, should be used

as specified by the fabric softener instructions.

- The final part of a tumble dryer cycle occurs without heat (cool

down cycle) to ensure that the items are left at a temperature

that ensures that the items will not be damaged.

WARNING: Never stop a tumble dryer before the end

of the drying cycle unless all items are quickly removed

and spread out so that the heat is dissipated.

 Do not touch the machine when barefoot or with

wet or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity

socket. Hold the plug and pull.

 Do not open the detergent dispenser drawer while

the machine is in operation.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage

the safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in

an attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 The door can become quite hot during the wash cycle.

 If the appliance has to be moved, work in a group

of two or three people and handle it with the utmost

care. Never try to do this alone, because the

appliance is very heavy.

 Before loading laundry into the washer-dryer, make

sure the drum is empty.

 During the drying phase, the door tends to get

quite hot.

 Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

 Do not use the appliance to dry foam rubber or

similar elastomers.

 Make sure that the water tap is turned on during

the drying cycles.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Opening the porthole door manually

In the event that it is not possible to open the

porthole door due to a powercut, and if you wish to

remove the laundry, proceed as follows:

1. remove the plug from the electrical socket.

2. make sure the water level inside the machine is

lower than the door opening; if it is not, remove excess

water using the drain hose, collecting it in a bucket.

3. pull outwards using the tab as indicated in the

figure, until the plastic tie-rod is freed from its stop

position; pull downwards and open the door at the

same time.

Care and maintenance

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This

will limit wear on the hydraulic system inside the

washer-dryer and help to prevent leaks.

 Unplug the washer-dryer when cleaning it and

during all maintenance work.

Cleaning the washer-dryer

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of your

appliance

 Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The washer-dryer is fitted with a self-cleaning pump

which does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber which protects the

pump, situated in its bottom part.

 Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. unscrew the lid by

rotating it anti-clockwise

(see figure): a little water

may trickle out. This is

perfectly normal;

2. clean the inside thoroughly;

3. screw the lid back on.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

 Never use second-hand hoses.

Troubleshooting

Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make

sure that the problem cannot be not solved easily using the following list.

Problem:

The washer-dryer does not

switch on.

The wash cycle does not start.

The washer-dryer does not take

in water (the indicator light for

the first wash cycle stage

flashes rapidly).

The washer-dryer continuously

takes in and drains water.

The washer-dryer does not drain

or spin.

The washer-dryer vibrates a lot

during the spin cycle.

The washer-dryer leaks.

The START/PAUSE indicator light

(orange) and the function

indicator lights flash rapidly.

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or is not making contact.

 There is no power in the house.

 The washer-dryer door is not closed properly.

 The ON/OFF button has not been pressed.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A delayed start has been set (see Personalisation).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 The drain hose is not fitted at a height between 65 and 100 cm from

the floor (see Installation).

 The free end of the hose is under water (see Installation).

 The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and contact the Assistance Service. If the

dwelling is on one of the upper floors of a building, there may be problems

relating to water drainage, causing the washer-dryer to fill with water and

drain continuously. Special anti-draining valves are available in shops and

help to avoid this inconvenience.

 The wash cycle does not include draining: some wash cycles require

the drain phase to be started manually.

 The ANTI-CREASE function has been activated: To complete the wash

cycle, press the START/PAUSE button (Personalisation).

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The washer-dryer is not level (see Installation).

 The washer-dryer is trapped between cabinets and walls (see Installation).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser drawer is blocked (for cleaning instructions, see

Care and maintenance).

 The drain hose is not fixed properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute

and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

 The detergent is not suitable for machine washing (it should display the

text for washer-dryers or hand and machine wash, or the like).

 Too much detergent was used.

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 A delayed start has been set.

 The DRYING knob is on the

setting.

Service

Before calling for Assistance:

 Check whether you can solve the problem alone (see Troubleshooting);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Assistance Centre using the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised technicians.

Have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate applied to the rear of the washer-dryer, and can also be

found on the front of the appliance by opening the door.

Français

! Ce symbole vous rappelle de lire ce mode d'emploi.

Sommaire

Installation, 18-19-20-21-22-23

Déballage et mise à niveau

Raccordements eau et électricité

Premier cycle de lavage

Caractéristiques techniques

Instructions pour l'installateur

Description du lavante-séchante et

démarrage dun programme, 24-25

Bandeau de commandes

Voyants

Démarrage dun programme

Programmes,26

Tableau des programmes

Personnalisations, 27

Sélection de la température

Sélectionner le séchage

Fonctions

Produits lessiviels et linge, 28

Tiroir à produits lessiviels

Cycle blanchissage

Triage du linge

Linge ou vêtements particuliers

Système déquilibrage de la charge

Précautions et conseils, 29

Sécurité générale

Mise au rebut

Ouverture manuelle de la porte hublot

Entretien et soin, 30

Coupure de larrivée deau et du courant

Nettoyage du lavante-séchante

Nettoyage du tiroir à produits lessiviels.

Entretien du hublot et du tambour

Nettoyage de la pompe

Contrôle du tuyau darrivée de leau

Anomalies et remèdes, 31

Assistance, 32

CAWD 125

Mode demploi

LAVANTE-SÉCHANTE

Installation

 Conserver ce mode demploi pour pouvoir le

consulter à tout moment. En cas de vente, de

cession ou de déménagement, veiller à ce quil suive

toujours le lavante-séchante pour que son nouveau

propriétaire soit informé sur son mode de

fonctionnement et puisse profiter des conseils

correspondants.

 Lire attentivement les instructions: elles fournissent

des conseils importants sur linstallation, lutilisation et

la sécurité de lappareil.

Déballage et mise à niveau

Déballage

1. Déballer le lavante-séchante.

2. Contrôler que le lavante-séchante na pas été

endommagé pendant le transport. Sil est abîmé, ne

pas le raccorder et contacter le vendeur.

3. Enlever les 4 vis de

protection servant au

transport, le caoutchouc

et la cale, placés dans la

partie arrière (voir figure).

4. Boucher les trous à laide des bouchons plastique

fournis.

5. Conserver toutes ces pièces: il faudra les remonter

en cas de transport du lavante-séchante.

 Les pièces demballage ne sont pas des jouets pour

enfants.

Mise à niveau

1. Installer le lavante-séchante sur un sol plat et

rigide, sans lappuyer contre des murs, des meubles

ou autre.

2. Si le sol nest pas

parfaitement horizontal,

visser ou dévisser les

pieds de réglage avant

(voir figure) pour niveler

lappareil; son angle

dinclinaison, mesuré sur

le plan de travail, ne doit

pas dépasser 2°.

Une bonne mise à niveau garantit la stabilité de

lappareil et évite quil y ait des vibrations, du bruit et

des déplacements en cours de fonctionnement. Si la

machine est posée sur de la moquette ou un tapis,

régler les pieds de manière à ce quil y ait

suffisamment despace pour assurer une bonne

ventilation.

Raccordements eau et électricité

Raccordement du tuyau darrivée de leau

1. Reliez le tuyau

d'alimentation en le

vissant à un robinet d'eau

froide à embout fileté 3/4

gaz (voir figure).

Faire couler leau jusquà

ce quelle soit limpide et

sans impuretés avant de

raccorder.

2. Raccorder le tuyau

darrivée de leau au

lavante-séchante en le

vissant à la prise deau

prévue, dans la partie

arrière en haut à droite

(voir figure).

3. Attention à ce que le tuyau ne soit pas plié ou

écrasé.

 La pression de leau doit être comprise entre les

valeurs indiquées dans le tableau des Caractéristiques

techniques (voir page ci-contre).

 Si la longueur du tuyau dalimentation ne suffit pas,

sadresser à un magasin spécialisé ou à un technicien

agréé.

 Nutiliser que des tuyaux neufs.

 Utiliser ceux qui sont fournis avec lappareil.

Raccordement du tuyau de vidange

Raccordez le tuyau

d'évacuation, sans le

plier, à un conduit

d'évacuation ou à une

évacuation murale

placés à une distance

du sol comprise entre

65 et 100 cm;

ou bien accrochez-le à

un évier ou à une

baignoire, dans ce cas,

fixez le support en

plastique fourni avec

l'appareil au robinet

(voir figure). L'extrémité

libre du tuyau

d'évacuation ne doit

pas être plongée dans

l'eau.

 L'utilisation de tuyaux de rallonge est absolument

déconseillée, si vous ne pouvez vraiment pas faire

autrement vous devrez utiliser un tuyau de même

diamètre et de longueur maximum de 150 cm.

Branchement électrique

Avant de brancher votre électroménager à la prise

de courant, contrôlez que:

 la prise est bien avec terre et conforme aux

réglementations applicables en la matière;

 la prise électrique est bien apte à supporter la

puissance maximum de l'électroménager figurant

sur la plaquette des caractéristiques (voir page 21);

 la tension d'alimentation est bien comprise entre

les valeurs figurant sur la plaquette des

caractéristiques (voir page 21);

 la prise est bien compatible avec la fiche du lave-

linge. Autrement, remplacez la prise ou la fiche.

Votre électroménager dispose à présent d'une fiche

moulée 13 ampères qui peut être branchée dans

une prise compatible pour utilisation immédiate.

Veuillez lire les instructions suivantes avant d'utiliser

votre électroménager.

ATTENTION - L'ELECTROMENAGER DOIT ETRE

RACCORDE A LA MASSE. LES OPERATIONS

DECRITES CI-APRES DOIVENT ETRE

EFFECTUEES PAR UN ELECTRICIEN QUALIFIE.

Remplacement du fusible:

En cas de remplacement d'un fusible défectueux, utilisez

toujours des fusibles de 13 ampères ASTA conformes au

standard BS1362 et remontez le couvercle du fusible. Si

vous avez perdu le couvercle du fusible, n'utilisez pas la

fiche tant que la pièce manquante n'aura pas été

remplacée.

Couvercles des fusibles:

Si vous remplacez le couvercle du fusible, veillez à ce que

sa couleur soit bien celle qui est indiquée par le code ou

l'indication colorée à la base de la fiche. Pour toute pièce

détachée, adressez-vous directement au centre

d'assistance technique le plus proche de chez vous.

Démontage de la fiche:

Si l'électroménager est équipé d'une fiche

incorporée qui ne peut pas être câblée à nouveau et

s'il faut faire passer le câble à travers des divisions,

des unités, etc. contrôlez que:

la fiche est bien remplacée par une autre câblable à

nouveau de 13 ampères portant la marque BSI

ou bien:

que le câble est bien raccordé directement à la prise

de 13 ampères, contrôlée par un interrupteur (con-

forme BS 5733) accessible sans qu'il faille déplacer

l'électroménager.

Elimination de la fiche:

Avant d'éliminer la fiche, rendez les broches

inutilisables de manière à ce que la fiche ne puisse

pas être branchée accidentellement dans une prise.

Instructions pour le raccordement du câble à une

fiche alternative:

Important: les couleurs des fils du câble de réseau

correspondent à la codification suivante:

Jaune/Vert Terre

Bleu Neutre

Marron Alimenté

Les couleurs des fils du câble pourraient ne pas

correspondre aux indications de couleur qui

identifient les broches de la fiche, procédez comme

suit:

raccordez le fil jaune/vert à la borne repérée par la

lettre E ou

ou de couleur verte ou jaune/vert

raccordez le fil marron à la borne repérée par la

lettre L ou de couleur rouge

raccordez le fil bleu à la borne repérée par la lettre N

ou de couleur noire.

65 - 100 cm

En cas d'utilisation d'une fiche de 13 ampères (BS

1363), installez un fusible de 13 ampères dans la fiche

ou sur l'adaptateur ou sur la carte de distribution.

En cas de doute sur l'alimentation électrique de votre

électroménager, faites appel à un électricien qualifié

avant de le mettre en service.

Raccordement d'une fiche alternative:

les couleurs des fils du câble de réseau

correspondent à la codification suivante:

BLEU NEUTRE (N)

MARRON ALIMENTE (L)

JAUNE/VERT TERRE (E)

Elimination de l'électroménager:

Lors de la mise au rebus de l'électroménager,

débarrassez-le de sa fiche en coupant le câble

d'alimentation le plus près possible de cette dernière

et éliminez comme décrit précédemment.

 Votre lave-linge ne doit pas être installé dehors,

même à l'abri, car il est très dangereux de le laisser

exposé à la pluie et aux orages.

 Après installation du lave-linge, la prise de courant

doit être facilement accessible.

 N'utilisez ni rallonges ni prises multiples.

 Le câble ne doit être ni plié ni écrasé.

 Le câble d'alimentation ne doit être remplacé que

par des techniciens agréés.

Attention! Nous déclinons toute responsabilité en cas

de non respect des normes énumérées ci-dessus.

Premier cycle de lavage

Avant la première mise en service de lappareil,

effectuer un cycle de lavage avec un produit lessiviel

mais sans linge et sélectionner le programme 1.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

La page charge ...

Whirlpool CAWD 125 (EX) Mode d'emploi

Marque: Whirlpool

Modèle: CAWD 125 (EX)

Catégorie: Machines à laver

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool CAWD 125 (EX) User guide

Whirlpool CAWD 125 (EX) Mode d'emploi

Whirlpool CAWD 125 (EX) Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents