Whirlpool AKZM 831 Le manuel du propriétaire

Marque: Whirlpool

Modèle: AKZM 831

Catégorie: Fours

Taper: Le manuel du propriétaire

Ce manuel convient également à

AKZM 831/IX

User and maintenance manual

Manuel d’utilisation et d’entretien

Інструкція з експлуатації і

технічного обслуговування

AKZM 831

GB1

YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT

This manual and the appliance itself provide important safety warnings, to be read and observed at all times.

All safety warnings give specific details of the potential risk present and indicate how to reduce risk of injury, damage and electric

shock resulting from improper use of the appliance. Carefully observe the following instructions:

- The appliance must be disconnected from the power supply before carrying out any installation work.

- Installation and maintenance must be carried out by a qualified technician, in compliance with the manufacturer’s

instructions and local safety regulations. Do not repair or replace any part of the appliance unless specifically stated in the

user manual.

- Regulations require that the appliance is earthed.

- The power cable must be long enough for connecting the appliance, once fitted in its housing, to the power supply

socket.

- For installation to comply with current safety regulations, an all-pole disconnect switch with minimum contact gap of

3 mm must be utilized.

- Do not use multiple plug adapters or extension leads.

- Do not pull the power supply cable in order to unplug the appliance.

- The electrical components must not be accessible to the user after installation.

- Do not touch the appliance with any wet part of the body and do not operate it when barefoot.

- This appliance is designed solely for use as a domestic appliance for cooking food. No other type of use is permitted

(e.g.: heating rooms). The Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls.

- The appliance is not intended for use by persons (including children) with any physical, sensory or mental impairment, or

without experience and knowledge of the appliance, unless supervised or previously instructed in its use by those

responsible for their safety.

- The accessible parts of the appliance may become very hot during use. Young children should be kept away from the

appliance and supervised to ensure that they do not play with it.

- During and after use, do not touch the heating elements or interior surfaces of the appliance - risk of burns. Do not allow

the appliance to come into contact with cloths or other flammable materials until all the components have cooled

sufficiently.

- At the end of cooking, exercise caution when opening the appliance door, letting the hot air or steam exit gradually

before accessing the oven. When the appliance door is shut, hot air is vented from the aperture above the control panel.

Do not obstruct the vent apertures.

- Use oven gloves to remove pans and accessories, taking care not to touch the heating elements.

- Do not place flammable materials in or near the appliance: a fire may break out if the appliance is inadvertently switched

on.

- Do not heat or cook sealed jars or containers in the appliance. The pressure that builds up inside might cause the jar to

explode, damaging the appliance.

- Do not use containers made of synthetic materials.

- Overheated oils and fats catch fire easily. Always remain vigilant when cooking foods rich in fat and oil.

- Never leave the appliance unattended during food drying.

- If alcoholic beverages are used when cooking foods (e.g. rum, cognac, wine), remember that alcohol evaporates at high

temperatures. As a result, there is a risk that vapours released by the alcohol may catch fire upon coming into contact with

the electrical heating element.

Scrapping of household appliances

- This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal

regulations. Before scrapping, cut off the power supply cable.

- For further information on the treatment, recovery and recycling of household electrical appliances, contact your

competent local authority, the collection service for household waste or the store where you purchased the appliance.

IMPORTANT SAFETY INSTRUCTIONS

This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others.

All safety warnings are preceded by the danger symbol and the following terms:

DANGER

Indicates a hazardous situation which, if not avoided, will cause serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could cause serious injury.

GB2

After unpacking the oven, make sure that it has not been damaged during transport and that the oven door closes properly. In

the event of problems, contact the dealer or your nearest After-sales Service. To prevent any damage, only remove the oven

from its polystyrene foam base at the time of installation.

PREPARING THE HOUSING UNIT

• Kitchen units in contact with the oven must be heat resistant (min 90°C).

• Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all wood chips and sawdust.

• Ensure the levelness of the oven support surface.

• After installation, the bottom of the oven must no longer be accessible.

• For correct appliance operation, do not obstruct the minimum gap between the worktop and the upper edge of the oven.

ELECTRICAL CONNECTION

Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front

edge of the oven (visible when the door is open).

• Power cable replacement (type H05 RR-F 3 x 1.5 mm

) must be carried out by a qualified electrician. Contact an

authorized service centre.

GENERAL RECOMMENDATIONS

Before use:

- Remove cardboard protection pieces, protective film and adhesive labels from accessories.

- Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell and fumes from the

insulating materials and protective grease.

During use:

- Do not place heavy objects on the door as they could damage it.

- Do not cling to the door or hang anything from the handle.

- Do not cover the inside of the oven with aluminium foil.

- Never pour water into the inside of a hot oven; this could damage the enamel coating.

- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.

- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become trapped in the door.

- Do not expose the oven to atmospheric agents.

Disposal of packing material

The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the packing must

therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.

Scrapping the product

- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment

(WEEE).

- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

- The symbol on the product or on the accompanying documentation indicates that it should not be treated as

domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic

equipment.

Energy saving

- Only pre-heat the oven if specified in the cooking table or your recipe.

- Use dark lacquered or enamelled baking moulds as they absorb heat far better.

- This oven, which is intended to come into contact with foodstuffs, complies with European Regulation ( ) n.1935/2004 and

has been designed, manufactured and sold in conformity with the safety requirements of the “Low Voltage” directive 2006/

95/CE (which replaces 73/23/CEE and subsequent amendments), the protection requirements of “EMC” 2004/108/CE.

INSTALLATION

SAFEGUARDING THE ENVIRONMENT

DECLARATION OF CONFORMITY

GB3

The oven does not work:

• Check for the presence of mains electrical power and if the oven is connected to the electrical supply.

• Turn off the oven and restart it to see if the fault persists.

The door will not open:

• Turn off the oven and restart it to see if the fault persists.

The electronic programmer does not work:

• If the display shows the letter “ ” followed by a number, contact your nearest After-sales Service. Specify in this case the

number that follows the letter “ ”.

Before calling the After-Sales Service:

1. See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide“.

2. Switch the appliance off and back on again it to see if the fault persists.

If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.

Always specify:

• a brief description of the fault;

• the type and exact model of the oven;

• the service number (number after the word Service on the rating plate), located on the right hand edge of the oven cavity

(visible when the oven door is open). The service number is also indicated on the guarantee booklet;

• your full address;

• your telephone number.

If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used

and repairs carried out correctly).

Oven exterior

IMPORTANT: Do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with

the appliance, clean it immediately with a damp cloth.

• Clean the surfaces with a damp cloth. If very dirty, add a few drops of neutral detergent to the water. Dry with a dry cloth.

Oven interior: STARCLEAN™ cleaning cycle

IMPORTANT: Do not use corrosive or abrasive detergents. Do not use abrasive sponges, metal scrapers or scouring pads

different from the sponge provided. Their use could eventually ruin the enamelled surfaces. Only use non-abrasive

sponges to clean the door glass.

The cavity of this oven is coated with a special formula enamel (nickel-free) enabling easily cleaning using just water and the

cellulose cloth provided. The cellulose cloth is washable and reusable until worn, and can be purchased from the Customer Care

Service. Washing the cloth in a washing-machine and drying it in a dryer is inadvisable.

TROUBLESHOOTING GUIDE

AFTER-SALES SERVICE

CLEANING

WARNING

- Never use steam cleaners.

- Clean the appliance when it is cold.

- Disconnect the appliance from the power supply.

GB4

STARCLEAN™ cleaning cycle

To keep the oven in best condition, carry out the STARCLEAN™ cleaning cycle after each use. The cycle takes 35 minutes,

including a cooling stage, and must be carried out as follows:

1. Proceed with oven cold.

2. Wet the cellulose cloth provided under running water and wring it out so that it does not drip.

3. Open the oven door and remove the enamelled accessories.

4. Cover the bottom of the oven completely with the cellulose cloth.

5. Distribute 350 ml of water evenly on the cellulose cloth. A smaller or greater amount of water could compromise proper

functioning of the cycle.

6. Close the oven door.

7. Select the symbol with the functions knob: the word STARCLEAN™ appears on the display.

8. Press button to confirm the choice and start the cleaning cycle. To prevent steam coming out, do not open the door

during the cycle.

9. At the end of the cycle, remove the cellulose cloth and eliminate any residual water in the oven.

10. Then start cleaning using the sponge provided, moistened with hot water (cleaning could be compromised if delayed by

more than 15 minutes).

Particularly stubborn grime

To eliminate particularly stubborn grime, repeat the STARCLEAN™ cycle and add a few drops of neutral detergent while

removing the grime.

Cleaning inside glass

The inside surface of the door glass has a special coating that makes it easy to cleaning.

To keep the door glass in best condition, after every STARCLEAN™ cleaning cycle, clean the glass using just water and a non-

abrasive sponge.

Add a few drops of neutral detergent to the water to eliminate any greasy residuals.

NOTES:

• The oven door can be removed to facilitate cleaning (see MAINTENANCE).

• The top heating element of the grill (see MAINTENANCE) can be lowered to clean the roof of the appliance.

• During prolonged cooking of foods containing lots of water (e.g. pizza, vegetables, etc.), condensation may form

inside the door and on the seal. Dry with a cloth or sponge when the oven is cold.

Accessories:

• Soak the accessories in water with washing up detergent after use, handling them with oven gloves if still hot.

• Food residues can be removed using a suitable brush or sponge.

• Do not put the enamelled accessories in a dishwasher. The harsh detergents normally used in dishwashers can

permanently damage the enamel.

REMOVING THE DOOR

To remove the door:

1. Open the door fully.

2. Lift the catches and push them forwards as far as they will go (Fig. 1).

3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2).

To refit the door:

1. Insert the hinges in their seats.

2. Open the door fully.

3. Lower the two catches.

4. Close the door.

MAINTENANCE

WARNING

- Use protective gloves.

- Ensure the oven is cold before carrying out the following operations.

- Disconnect the appliance from the power supply.

Fig. 1 Fig. 2

GB5

MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)

1. Remove the side accessory holder grilles (Fig. 3).

2. Pull the heating element out a little (Fig. 4) and lower it (Fig. 5).

3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to rest on the lateral

supports.

REPLACING THE OVEN LAMP

To replace the rear lamp (if present):

1. Disconnect the oven from the power supply.

2. Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover back on.

3. Reconnect the oven to the power supply.

To replace the side lamp (if present):

1. Disconnect the oven from the power supply.

2. Remove the side accessory holder grilles, if present (Fig. 3).

3. Use a screwdriver to prise off the lamp cover (Fig. 7).

4. Replace the lamp (see note for lamp type) (Fig. 8).

5. Reposition the lamp cover, pushing it on firmly until it snaps into place (Fig. 9).

6. Refit the side accessory holder grilles.

7. Reconnect the oven to the power supply.

N.B.:

- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C halogen lamps.

- Lamps are available from our After-sales Service.

IMPORTANT:

- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.

- Do not use the oven until the lamp cover has been repositioned.

Fig. 3 Fig. 4 Fig. 5

Fig. 6 Fig. 7 Fig. 8 Fig. 9

GB6

FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION

1. Control panel

2. Upper heating element/grill

3. Cooling fan (not visible)

4. Dataplate (not to be removed)

5. Light

6. Fan

7. Turnspit

8. Lower heating element (not visible)

9. Door

10. Position of shelves (the number of shelves is indicated on the front of the oven)

11. Rear wall

N.B.:

- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.

- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a while.

- When the oven door is opened during cooking, the heating elements switch off.

ACCESSORIES SUPPLIED

A. WIRE SHELF (2): the wire shelf can be used to grill food or as a support for pans, cake tins and other ovenproof cooking

receptacles.

B. DRIP TRAY (1): the drip tray is designed to be positioned under the wire shelf in order to collect fat or as an oven tray for

cooking meat, fish, vegetables, focaccia, etc.

C. TURNSPIT (1): for uniform roasting of large pieces of meat and poultry.

D. CELLULOSE CLOTH (1): to be used for the STARCLEAN™ cleaning cycle.

IMPORTANT: Only use the cellulose cloth provided.

E. SPONGE: to be used for removing grime in the cavity

ACCESSORIES NOT SUPPLIED

Other accessories can be purchased separately from the After-sales Service.

INSTRUCTIONS FOR OVEN USE

Fig. A Fig. B Fig. C Fig. D Fig. E

GB7

INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN

The wire shelf and other accessories are provided with a locking mechanism to prevent their unintentional removal.

1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).

2. Angle the wire shelf when it reaches the locking position “B” (Fig. 2).

3. Return the wire shelf to the horizontal position and push it in fully to “C” (Fig. 3).

4. To remove the wire shelf proceed in reverse order.

The other accessories, like the drip tray and baking tray, are inserted in exactly the same way. The protrusion on the flat surface

enables the accessories to lock in place.

CONTROL PANEL DESCRIPTION

ELECTRONIC PROGRAMMER

1. FUNCTION SELECTOR KNOB: On/off and function selector knob

2. BROWSE KNOB: for browsing the menu and adjusting pre-set values

3. BUTTON : to return to the previous screen

4. BUTTON : to select and confirm settings

LIST OF FUNCTIONS

Turn the “Functions” knob to any position and the oven switches on: the display shows the functions or the associated

submenus.

The submenus are available and selectable by turning the knob to the functions GRILL, SPECIALS, SETTINGS, BREAD/PIZZA.

N.B.: for the list and description of functions, see the specific table at page 12.

DESCRIPTION OF DISPLAY

A. Display of heating elements activated during the various cooking functions

B. Time management symbols: timer, cooking time, end of cooking time, time

C. Information regarding selected functions

D. Automatic BREAD/PIZZA function selected

E. Indication of door locked during automatic cleaning cycle (if present)

F. Internal oven temperature

G. Pyrolisis function (if present)

H. Browning

I. Special functions: defrost, keep warm, rising

Fig. 1

Fig. 2 Fig. 3

B C D

I H G F

GB8

STARTING THE OVEN - SETTING THE TIME

After connecting the oven to the mains power, the time must be set on the clock. The two hour digits flash on the display.

1. Turn the “Browse” knob to display the correct hour.

2. Press the button to confirm; the two minute digits flash on the display.

3. Turn the “Browse” knob to display the correct minutes.

4. Press button to confirm.

To change the time, for example following a power cut, see the next paragraph (SETTINGS).

SELECTING COOKING FUNCTIONS

1. Turn the “Functions” knob to the desired function: the cooking settings are shown on the display.

2. If the values shown are those desired, press . To change them, proceed as indicated below.

SETTING THE TEMPERATURE/OUTPUT OF THE GRILL

To change the temperature or output of the grill, proceed as follows:

1. Turn the “Browse” knob to display the desired value.

2. Press button to confirm.

The oven automatically confirms your selection 10 seconds after the last operation.

FAST PREHEATING

1. Turn the “Functions” knob to the symbol to select the fast preheating function.

2. Confirm by pressing : the settings are shown on the display.

3. If the proposed temperature is that desired, press button . To change the temperature, proceed as described in

previous paragraphs. The message PRE appears on the display. When the set temperature is reached, the corresponding

value (e.g. 200°C) appears on the display and the acoustic signal sounds. At the end of preheating, the oven automatically

selects the conventional function .

At this point food can be placed in the oven for cooking.

4. If you wish to set a different cooking function, turn the “Functions” knob and select the desired function.

SETTING COOKING TIME

This function can be used to cook food for a set length of time, from a minimum of 1 minute to the maximum time allowed by

the selected function, after which the oven switches off automatically.

1. Once the temperature is confirmed, the symbol flashes.

2. Turn the adjustment knob to display the desired cooking time.

3. To confirm the cooking time, press button .

The oven automatically confirms your selection 10 seconds after the last operation.

GB9

SETTING END OF COOKING TIME /START DELAYED

IMPORTANT: the start delayed setting is not available for the following functions: FAST PREHEATING, BREAD/PIZZA,

GENTLE CONVECTION BAKE.

N.B.: with this setting, the selected temperature is reached in a more gradual way, so cooking times will be slightly

longer than stated in the cooking table.

The end of cooking time can be set, delaying the start of cooking by up to a maximum of 23 hours and 59 minutes. This can only

be done once cooking time has been set.

After setting cooking time, the display shows the end of cooking time (for example 15:45) and the symbol flashes.

To delay the end of cooking time, and thus also the cooking start time, proceed as follows:

1. Turn the “Browse” knob to display the time you wish cooking to end (for example 16:00).

2. Confirm the selected value by pressing button : the two dots of end of cooking time flash, indicating that the setting

has been made correctly.

3. The oven will automatically delay the start of cooking so as to finish cooking at the set time.

At any time, however, set values (temperature, grill setting, cooking time) can be changed using button to go back,

followed by the “Browse” knob to change values and button to confirm.

INDICATION OF THE RESIDUAL HEAT INSIDE THE OVEN (IF PRESENT)

If at the end of cooking, or when the oven is switched off, the temperature inside the oven is high, the display on some models

shows the message HOT together with the current temperature. Once the oven chamber has cooled down, the display shows

the current time again.

TIMER

This function can be used only with the oven switched off and is useful, for example, for monitoring the cooking time of pasta.

The maximum time which can be set is 23 hours and 59 minutes.

1. With the “Functions” knob at zero, turn the “Browse” knob to display the desired time.

2. Press button to start the countdown. When the set time has elapsed, the display will show “0:00” and an acoustic signal

will sound. To mute the acoustic signal, press button (the time of day appears on the display).

SELECTING SPECIAL FUNCTIONS

Turn the “Functions” knob indicator to the symbol to access a submenu containing three special functions.

To browse, select and start one of these functions, proceed as follows:

1. Turn the “Functions” knob to symbol : the display shows “ DEFROST” along with this function’s corresponding symbol.

2. Turn the “Browse” knob to scroll the list of functions; the function names are in English: DEFROST, KEEP WARM, RISING.

3. Press button to confirm.

BROWNING

At the end of cooking, with certain functions, the display indicates the possibility of browning. This function can only be used

when cooking time has been set.

At the end of cooking time, the display shows: “PRESS TO BROWN”. Press button , and the oven starts a 5 minute browning

cycle. This function can be selected consecutively a maximum of twice.

GB10

BREAD/PIZZA FUNCTION SELECTION

Turn the “Functions” knob indicator to the symbol to access a submenu containing two automatic cooking functions for

“bread” and “pizza”.

Bread

1. Turn the “Functions” knob to symbol : the display shows “BREAD” and AUTO at the side.

2. Press to select the function.

3. Turn the “Browse” knob to set the required temperature (between 180°C and 220°C) and confirm with button .

4. Turn the “Browse” knob to set the required cooking duration and press to start cooking.

Pizza

1. Turn the Functions knob to symbol : the display shows “BREAD”. To select the “PIZZA” function, proceed as follows:

2. Turn the “Browse” knob: “PIZZA” appears on the display.

3. Press to select the function.

4. Turn the “Browse” knob to set the required temperature (between 220°C and 250°C) and confirm with button .

5. Turn the “Browse” knob to set the required cooking duration and press to start cooking.

SETTINGS

Turn the “Functions” knob indicator to the symbol to access a submenu containing four display settings which can be

changed.

Clock

Turn the “Functions” knob to the symbol : the word CLOCK appears on the display. To change the time of day, see the

previous paragraph (SETTING THE TIME).

Eco

With the ECO mode selected (ON), the display switches off when the oven is on standby or 5 minutes after the end of cooking.

To view information on the display, simply press a button or turn a knob.

1. Turn the “Browse” knob to display “ECO.

2. Press to access the setting (ON/OFF).

3. Turn the “Browse” knob to select the desired setting and confirm by pressing button .

Acoustic signal

To activate or deactivate the acoustic signal, proceed as follows:

1. Turn the “Browse” knob to display “SOUND.

2. Press to access the setting (ON/OFF).

3. Turn the “Browse” knob to select the desired setting and confirm by pressing button .

N.B.: when set to off, the following signals remain nonetheless active: timer end, preheating end, cooking end.

Brightness

To change the display brightness, proceed as follows:

1. Turn the “Browse” knob to display “BRIGHTNESS.

2. Press button : the display shows LOW, MID or HIGH depending on the level currently set.

3. Turn the “Browse” knob to increase or decrease brightness and confirm by pressing .

GB11

STARCLEAN™ CLEANING CYCLE

To keep the oven in best condition, carry out the STARCLEAN™ cleaning cycle after each use. The cycle takes 35 minutes,

including a cooling stage, and must be carried out as follows:

For the description of this function, see the section CLEANING and the functions table on page 12.

1. Proceed with oven cold.

2. Wet the cellulose cloth provided under running water and wring it out so that it does not drip.

3. Open the oven door and remove the enamelled accessories.

4. Cover the bottom of the oven completely with the cellulose cloth.

5. Distribute 350 ml of water evenly on the cellulose cloth. A smaller or greater amount of water could compromise proper

functioning of the cycle.

6. Close the oven door.

IMPORTANT: To prevent steam coming out, do not open the door during the cycle.

7. Select the symbol with the functions knob: the word STARCLEAN™ appears on the display.

8. Press button to confirm the choice and start the cleaning cycle. To prevent steam coming out, do not open the door

during the cycle.

9. At the end of the cycle, remove the cellulose cloth and eliminate any residual water in the oven.

10. Then start cleaning using the sponge provided, moistened with hot water (cleaning could be compromised if delayed by

more than 15 minutes).

Particularly stubborn grime

To eliminate particularly stubborn grime, repeat the STARCLEAN™ cycle and add a few drops of neutral detergent while

removing the grime.

KEY-LOCK

This function can be used to lock the buttons and knobs on the control panel.

To activate it, press and at the same time for at least 3 seconds. When activated, the functions associated with the buttons

are locked and the display shows a key symbol. This function can also be activated during cooking. To deactivate it, repeat the

above procedure. When the key-lock function is activated, the oven can be switched off by turning the knob to 0 (zero). In this

case, however, the previously selected function will have to be set again.

GB12

FUNCTION DESCRIPTION TABLE

FUNCTIONS KNOB

OFF To stop cooking and switch off the oven.

LAMP To switch the oven interior light on/off.

SPECIALS

DEFROST

To speed up defrosting of food. Place food on the middle shelf. Leave food in its packaging in

order to prevent it from drying out on the outside.

KEEP WARM

For keeping just-cooked food hot and crisp (e.g: meat, fried food or flans). Place food on the

middle shelf. The function will not activate if the temperature in the oven is above 65°C.

RISING

For optimal rising of sweet or savoury dough. To safeguard the quality of proving, the function

will not activate if the temperature in the oven is above 40°C. Place the dough on the 2nd shelf.

The oven does not have to be preheated.

CONVENTIONAL

To cook any kind of dish on one shelf only. Use the 3rd shelf. To cook pizza, savoury pies and

sweets with liquid fillings, use the 1st or 2nd shelf. Preheat the oven before placing food inside.

CONVECTION BAKE

For baking cakes with liquid filling (sweet or savoury) on a single shelf. This function can also be

used for cooking on two shelves. Switch the position of the dishes to cook food more evenly. Use

the 3rd shelf to cook on one shelf only, and the 1st and 4th to cook on two shelves. Preheat the

oven before cooking.

GENTLE CONVECTION

BAKE

To cook food requiring medium/low cooking temperatures on a maximum of two shelves. This

function is used to cook gently and slowly on two levels without having to switch the position of

the dishes during the cooking process. Use the 3rd shelf to cook on one shelf only, and the 1st

and 4th to cook on two shelves. Preheat the oven before cooking.

GRILL

To grill steak, kebabs and sausages; to cook vegetables au gratin and toast bread. Place food on

the 4th or 5th shelf. When grilling meat, use the drip tray to collect the cooking juices. Position it

on the 3rd/4th shelf, adding approx. half a litre of water. The oven does not have to be

preheated. During cooking the oven door must remain closed.

TURBO GRILL

To roast large joints of meat (legs, roast beef, chickens). Position the food on the middle shelves.

Use the drip tray to collect the cooking juices. Position it on the 1st/2nd shelf, adding approx.

half a litre of water. The oven does not have to be preheated. During cooking the oven door must

remain closed. With this function you can also use the turnspit, if provided.

MAXI COOKING

To cook large joints of meat (above 2.5 kg). Use the 1st or 2nd shelf, depending on the size of the

joint. The oven does not have to be preheated. It is advisable to turn the meat over during

cooking for more even browning. It is best to baste the meat every now and again to avoid it

drying out.

SETTINGS To set the display (time, brightness, buzzer volume, energy saving).

BREAD/PIZZA

To bake different types and sizes of pizza and bread. This function contains two programmes

with predefined settings. Simply indicate the values required (temperature and time) and the

oven will manage the cooking cycle automatically. Place the dough on the 2nd shelf after

preheating the oven.

STARCLEAN™

To eliminate the dirt created by cooking by means of a low temperature cycle. The combined

action of the special enamel and the water released by the cellulose cloth during the cycle

facilitates removal of grime. Activate the function when the oven is cold.

FAST PREHEATING To preheat the oven rapidly.

GB13

COOKING TABLE

Recipe

Function Preheating Shelf

(from bottom)

Temperature

(°C)

Time

(min)

Accessories

Leavened cakes

Yes 2 / 3 160-180 30-90 Cake tin on wire shelf

GENTLE

Yes 1-4 160-180 30-90

Shelf 4: cake tin on wire shelf

Shelf 1: cake tin on wire shelf

Filled pies (cheesecake,

strudel, fruit pie)

Yes 3 160-200 30-85

Drip tray/ baking tray or cake tin on

wire shelf

Yes 1-4 160-200 35-90

Shelf 4: cake tin on wire shelf

(switch levels halfway through

cooking)

Shelf 1: cake tin on wire shelf

Biscuits/Tartlets

Yes 3 170-180 15-45 Drip tray / baking tray

GENTLE

Yes 1-4 160-170 20-45

Shelf 4: wire shelf

Shelf 1: drip tray / baking tray

Choux buns

Yes 3 180-200 30-40 Drip tray / baking tray

GENTLE

Yes 1-4 180-190 35-45

Shelf 4: oven tray on wire shelf

Shelf 1: drip tray / baking tray

Meringues

Yes 3 90 110-150 Drip tray / baking tray

GENTLE

Yes 1-4 90 130-150

Shelf 4: oven tray on wire shelf

Shelf 1: drip tray / baking tray

Bread / Pizza / Focaccia

Yes 1 / 2 190-250 15-50 Drip tray / baking tray

Yes 1-4 190-250 25-45

Shelf 4: oven tray on wire shelf

(switch levels halfway through

cooking)

Shelf 1: drip tray / baking tray

Frozen pizza

Yes 3 250 10-15

Shelf 3: drip tray / baking tray or

wire shelf

Yes 1-4 250 10-20

Shelf 4: oven tray on wire shelf

(switch levels halfway through

cooking)

Shelf 1: drip tray / baking tray

Savoury pies

(vegetable pie, quiche)

Yes 3 180-190 40-55 Cake tin on wire shelf

Yes 1-4 180-190 40-55

Shelf 4: cake tin on wire shelf

(switch levels halfway through

cooking)

Shelf 1: cake tin on wire shelf

Vols-au-vent / Puff

pastry crackers

Yes 3 190-200 20-30 Drip tray / baking tray

GENTLE

Yes 1-4 180-190 20-40

Shelf 4: oven tray on wire shelf

Shelf 1: drip tray / baking tray

GB14

Lasagne / Baked pasta /

Cannelloni / Flans

Yes 3 190-200 45-55 Oven tray on wire shelf

Lamb / Veal / Beef / Pork

1Kg

Yes 3 190-200 80-110 Drip tray or oven tray on wire shelf

Chicken / Rabbit / Duck

1Kg

Yes 3 200-230 50-100 Drip tray or oven tray on wire shelf

Turkey / Goose 3 Kg Yes 2 190-200 80-130 Drip tray or oven tray on wire shelf

Baked fish / en papillote

(fillet, whole)

Yes 3 180-200 40-60 Drip tray or oven tray on wire shelf

Stuffed vegetables

(tomatoes, courgettes,

aubergines)

Yes 2 180-200 50-60 Oven tray on wire shelf

Toas t - 5 High 3-5 Wire shelf

Fish fillets / steaks - 4 Medium

20-30

Shelf 4: wire shelf (turn food

halfway through cooking)

20-30 Shelf 3: drip tray with water

Sausages / Kebabs /

Spare ribs /

Hamburgers

- 5 Medium - High 15-30

Shelf 5: wire shelf (turn food

halfway through cooking)

Shelf 4: drip tray with water

Roast chicken 1-1.3 Kg

- 2 Medium 55-70

Shelf 2: wire tray (turn food two

thirds of the way through cooking)

- 2 High 60-80 Shelf 2: Turnspit

Roast Beef rare 1 Kg - 3 Medium 35-45

Oven tray on wire shelf (turn food

two thirds of the way through

cooking if necessary)

Leg of lamb / Shanks - 3 Medium 60-90

Drip tray or oven tray on wire shelf

(turn food two thirds of the way

through cooking if necessary)

Roast potatoes - 3 Medium 45-55

Drip-tray / baking tray (if necessary,

turn food two thirds of the way

through cooking)

Vegetable gratin - 3 High 10-15 Oven tray on wire shelf

Lasagne & Meat Yes 1-4 200 50-100

Shelf Oven tray on wire shelf (turn

food two thirds of the way through

cooking if necessary)

Shelf 1: drip tray or oven tray on

wire shelf

Meat & Potatoes Yes 1-4 200 45-100

Shelf Oven tray on wire shelf (turn

food two thirds of the way through

cooking if necessary)

Shelf 1: drip tray or oven tray on

wire shelf

Fish & Vegetables

GENTLE

Yes 1-4 180 30-50

Shelf 4: oven tray on wire shelf

Shelf 1: drip tray or oven tray on

wire shelf

Recipe

Function Preheating Shelf

(from bottom)

Temperature

(°C)

Time

(min)

Accessories

GB15

Table of Tested Recipes (in compliance with IEC 60350:99+A1:05 +A2:08 and DIN 3360-12:07:07)

The cooking table advises the ideal function and cooking temperature to ensure the best results with all recipes. For hot air

cooking on a single level, it is advisable to use the third shelf and the same temperature suggested for “CONVECTION BAKE”

cooking on several levels.

When grilling food, leave a space of 3-4 cm at the front to facilitate removal from the oven.

Recipe Function Preheating Shelf

(from bottom)

Temperature

(°C)

Time

(min)

Accessories and notes

IEC 60350:99+A1:05 +A2:08 § 8.4.1

Shortbread

Yes 3 170 15-25 Drip tray / baking tray

Yes 1-4 160 25-35

Shelf 4: baking tray (switch levels

halfway through cooking)

Shelf 1: drip tray

IEC 60350:99+A1:05 +A2:08 § 8.4.2

Small cakes

Yes 3 170 20-30 Drip tray / baking tray

Yes 1-4 160 20-30

Shelf 4: baking tray (switch levels

halfway through cooking)

Shelf 1: drip tray

IEC 60350:99+A1:05 +A2:08 § 8.5.1

Fatless sponge cake Yes 2 170 25-35 Cake tin on wire shelf

IEC 60350:99+A1:05 +A2:08 § 8.5.2

Two apple pies

Yes 2 / 3 185 55-75 Cake tin on wire shelf

Yes 1-4 175 75-95

Shelf 4: cake tin on wire shelf

(switch levels halfway through

cooking)

Shelf 1: cake tin on wire shelf

IEC 60350:99+A1:05 +A2:08 § 9.1.1

Toast - 5 High 3-5 Wire shelf

IEC 60350:99+A1:05 +A2:08 § 9.2.1

Burgers

-5High20-30

Shelf 5: wire shelf (turn food

halfway through cooking)

- 5 High 20-30 Shelf 4: drip tray with water

DIN 3360-12:07 § 6.5.2.3

Apple cake, yeast tray cake

Yes 3 180 30-40 Drip tray / baking tray

Yes 1-4 160 50-60

Shelf 4: baking tray (switch levels

halfway through cooking)

Shelf 1: drip tray

DIN 3360-12:07 § 6.6

Roast Pork - 2 170 110-150 Shelf 2: drip tray

DIN 3360-12:07 annex C

Flat cake

Yes 3 170 35-45 Drip tray / baking tray

Yes 1-4 170 40-50

Shelf 4: baking tray (switch levels

halfway through cooking)

Shelf 1: drip tray

GB16

How to read the cooking table

The table indicates the best function to use for any given food, to be cooked on one or more shelves at the same time. Cooking

times start from the moment food is placed in the oven, excluding preheating (where required). Cooking temperatures and

times are purely for guidance and will depend on the amount of food and type of accessory used. Use the lowest recommended

values to begin with and, if the food is not cooked enough, then move on to higher values. Use the accessories supplied and

preferably dark coloured metal cake tins and oven trays. You can also use pans and accessories in pyrex or stoneware, but bear

in mind that cooking times will be slightly longer. To obtain best results, carefully follow the advice given in the cooking table

for the choice of accessories (supplied) to be placed on the various shelves.

Cooking different foods at the same time

Using the “GENTLE CONVECTION BAKE” function, you can cook different foods which require the same cooking temperature at

the same time (for example: fish and vegetables), using different shelves. Remove the food which requires less cooking time and

leave food which requires longer cooking time in the oven.

Desserts

- Cook delicate desserts with the conventional function on one shelf only. Use dark coloured metal cake tins and always

position them on the wire shelf supplied. To cook on more than one shelf, select the forced air function and stagger the

position of the cake tins on the shelves, aiding optimum circulation of the hot air.

- To check whether a raising cake is cooked, insert a wooden toothpick into the centre of the cake. If the toothpick comes

out clean, the cake is ready.

- If using non-stick cake tins, do not butter the edges as the cake may not rise evenly around the edges.

- If the cake “sinks” during cooking, set a lower temperature the next time, perhaps reducing the amount of liquid in the

mixture and mixing more gently.

- For sweets with moist fillings (cheesecake or fruit pies) use the “CONVECTION BAKE” function”. If the base of the cake is

soggy, lower the shelf and sprinkle the bottom of the cake with breadcrumbs or biscuit crumbs before adding the filling.

Meat

- Use any kind of oven tray or pyrex dish suited to the size of the piece of meat being cooked. For roast joints, it is best to

add some stock to the bottom of the dish, basting the meat during cooking for added flavour. When the roast is ready, let

it rest in the oven for another 10-15 minutes, or wrap it in aluminium foil.

- When you want to grill meat, choose cuts with an even thickness all over in order to achieve uniform cooking results. Very

thick pieces of meat require longer cooking times. To prevent the meat from burning on the outside, lower the position of

the wire shelf, keeping the food farther away from the grill. Turn the meat two thirds of the way through cooking.

To collect the cooking juices it is advisable to place a drip-tray with half a litre of water directly under the grill on which the meat

is placed. Top-up when necessary.

Turnspit

Use this accessory to evenly roast large pieces of meat and poultry. Place the meat on the turnspit rod, tying it with string if

chicken, and check that it is secure before inserting the rod in the seat located on the front wall of the oven and resting it on the

respective support. To prevent smoke and to collect cooking juices, it is advisable to place a drip-tray with half a litre of water on

the first level. The rod has a plastic handle which must be removed before starting to cook, and used at the end of cooking to

avoid burns when taking the food out of the oven.

Pizza

Lightly grease the trays to ensure the pizza has a crispy base. Scatter the mozzarella over the pizza two thirds of the way through

cooking.

Rising function

It is always best to cover the dough with a damp cloth before placing it in the oven. Dough proving time with this function is

reduced by approximately one third compared to proving at room temperature (20-25°C). Proving time for a 1 Kg batch of pizza

dough is around one hour.

RECOMMENDED USE AND TIPS

FR17

VOTRE SÉCURITÉ AINSI QUE CELLE D’AUTRUI EST PARTICULIÈREMENT IMPORTANTE

Le présent manuel contient d’importants messages relatifs à la sécurité, qui figurent également sur l’appareil. Nous vous invitons

à les lire soigneusement et à les respecter en toute circonstance.

Tous les messages relatifs à la sécurité spécifient le danger potentiel auquel ils se réfèrent et indiquent comment réduire le

risque de lésions, de dommages et de chocs électriques résultant d’une utilisation non réglementaire de l’appareil. Veuillez

observer scrupuleusement les instructions suivantes :

- Débranchez le four de l’alimentation secteur avant d’entreprendre toute intervention sur celui-ci.

- Les opérations d’installation et d’entretien sont du ressort exclusif d’un technicien spécialisé. Celui-ci est tenu de se

conformer aux instructions du fabricant et aux normes locales en vigueur en matière de sécurité. Pour toute réparation ou

tout remplacement de pièces, procédez uniquement aux opérations spécifiées dans le manuel en utilisant les pièces

expressément indiquées.

- La mise à la terre de l’appareil est obligatoire.

- Le cordon d’alimentation de l’appareil doit être suffisamment long pour permettre le branchement de l’appareil encastré

à la prise du secteur.

- Afin que l’installation soit conforme aux normes locales de sécurité, il est nécessaire de brancher l’appareil au moyen d’un

interrupteur omnipolaire avec une distance d’ouverture des contacts d’au moins 3 mm.

- N’utilisez en aucun cas de prises multiples ou de rallonges.

- Ne tirez jamais sur le cordon d’alimentation pour débrancher l’appareil de la prise secteur.

- Une fois l’installation terminée, l’utilisateur ne devra plus pouvoir accéder aux composants électriques.

- Évitez de toucher l’appareil avec les mains mouillées et ne l’utilisez pas lorsque vous êtes pieds nus.

- Ce four a été conçu uniquement comme appareil ménager destiné à la cuisson des aliments. Toute autre utilisation est

considérée comme impropre (chauffer une pièce, par exemple). Le fabricant décline toute responsabilité en cas de

dommages résultant d’une utilisation impropre ou d’un réglage erroné des commandes.

- Les personnes (y compris les enfants) qui, en raison de leurs capacités physiques, sensorielles ou mentales, de leur

inexpérience ou de leur méconnaissance, ne sont pas en mesure d’utiliser l’appareil en toute sécurité, doivent se servir de

l’appareil uniquement sous la surveillance ou en se conformant aux instructions d’une personne responsable.

- Les parties accessibles du four peuvent atteindre une température élevée quand l’appareil est en service. Veillez à

maintenir les enfants hors de portée de l’appareil. Contrôlez que les enfants ne jouent pas avec l’appareil.

- Veillez à ne pas toucher les résistances ou les surfaces intérieures du four, sous peine d’encourir des brûlures. Évitez de

mettre le four en contact avec des chiffons ou tout matériau inflammable avant que les composants de l’appareil ne

soient suffisamment refroidis.

- En fin de cuisson, soyez particulièrement prudent au moment d’ouvrir la porte. Laissez l’air chaud ou la vapeur s’évacuer

progressivement de l’enceinte de cuisson avant d’accéder à celle-ci. Lorsque la porte est fermée, l’air chaud est convoyé à

travers l’ouverture située au-dessus du bandeau de commande. Évitez d’obstruer les ouvertures de ventilation.

- Munissez-vous de gants pour retirer les plats et les accessoires chauds du four. Veillez à ne pas toucher les résistances.

- Ne placez jamais de produits inflammables à l’intérieur du four ou à proximité de celui-ci. Ces produits risqueraient en

effet de s’enflammer si le four était mis sous tension par inadvertance.

- Évitez de chauffer ou de cuisiner dans le four des aliments contenus dans des récipients hermétiques. La pression qui se

développe à l’intérieur du récipient pourrait le faire exploser et endommager le four.

- N’utilisez en aucun cas de récipients en matière synthétique pour cuire des aliments au four.

- Les graisses et l’huile surchauffées s’enflamment facilement. Surveillez régulièrement la cuisson si vous utilisez une

quantité importante de graisse ou d’huile.

- Ne laissez jamais l’appareil sans surveillance pendant le processus de séchage des aliments.

- Si vous utilisez des boissons alcoolisées (rhum, cognac, vin, par exemple) pour cuisiner des plats, rappelez-vous que

l’alcool s’évapore à des températures élevées. Il se peut, par conséquent, que les vapeurs dégagées par l’alcool

s’enflamment en entrant en contact avec la résistance électrique.

INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ

Ceci est le symbole de danger relatif à la sécurité. Il met en garde l’utilisateur et toute autre personne contre les risques

potentiels dérivant de l’utilisation de cet appareil.

Tous les messages relatifs à la sécurité sont précédés du symbole de danger et des termes suivants :

DANGER

Indique une situation dangereuse qui, si elle n’est pas évitée, occasionnera de graves

lésions.

AVERTISSEMENT

Indique une situation dangereuse qui, si elle n’est pas évitée, est susceptible

d’occasionner de graves lésions.

FR18

Mise au rebut des appareils ménagers usagés

- Cet appareil est fabriqué à partir de matériaux recyclables ou pouvant être réutilisés. Mettez-le au rebut en vous

conformant aux prescriptions locales en matière d’élimination des déchets. Avant de mettre votre appareil au rebut,

rendez-le inutilisable en sectionnant le câble d’alimentation.

- Pour toute information sur le traitement et le recyclage de cet appareil, contactez le service municipal compétent, votre

déchetterie locale ou le magasin où vous l’avez acheté.

Après avoir déballé le four, contrôlez que l’appareil n’a pas été endommagé pendant le transport et que la porte ferme

parfaitement. En cas de problème, contactez votre revendeur ou le Service Après-vente le plus proche. Nous recommandons de

retirer le four de la base en polystyrène uniquement avant de procéder à l’installation, afin d’éviter tout risque

d’endommagement de l’appareil.

PRÉPARATION DU MEUBLE POUR L’ENCASTREMENT

• Les meubles de cuisine adjacents au four doivent résister à la chaleur (min. 90 °C).

• Procédez au découpage complet du meuble avant d’y installer l’appareil et éliminez soigneusement les copeaux et la

sciure de bois.

• Vérifiez que la surface d'appui du four est parfaitement plane.

• On ne doit plus pouvoir accéder à la partie inférieure du four une fois l’installation terminée.

• Afin de garantir le bon fonctionnement de l’appareil, veillez à ne pas obstruer l’ouverture minimale prévue entre le plan

de travail et la partie supérieure du four.

BRANCHEMENT DE L’APPAREIL

Vérifiez que la tension figurant sur la plaque signalétique de l’appareil correspond à celle de votre habitation. La plaque

signalétique se trouve sur le rebord avant du four (visible lorsque la porte est ouverte).

• Le remplacement éventuel du câble d’alimentation (type H05 RR-F 3 x 1,5 mm

) doit être effectué uniquement par un

professionnel qualifié. Adressez-vous à un Service Après-vente agréé.

RECOMMANDATIONS GÉNÉRALES

Avant d’utiliser le four pour la première fois :

- Enlevez les protections en carton, les films transparents et les étiquettes autocollantes présentes sur les accessoires.

- Retirez tous les accessoires du four et faites-le chauffer à 200°C pendant une heure environ, afin de faire disparaître les

odeurs et les fumées qui se dégagent du matériau isolant et des graisses de protection.

Pendant l’utilisation :

- Évitez de déposer des objets lourds sur la porte du four sous peine de l’endommager.

- Évitez de prendre appui sur la porte du four ou de suspendre des objets sur la poignée du four.

- Évitez de couvrir l’intérieur du four avec des feuilles d’aluminium.

- Ne versez jamais d’eau dans le four lorsque celui-ci est chaud ; vous risqueriez d’endommager l’émail.

- Évitez de déplacer les ustensiles de cuisson en les traînant sur le fond du four sous peine de rayer le revêtement.

- Veillez à ce que le câble électrique d’autres appareils électroménagers se trouvant à proximité immédiate ne puisse ni

entrer en contact avec les parties chaudes, ni se coincer dans la porte du four.

- Évitez d’exposer le four aux éléments atmosphériques.

Élimination des emballages

Les matériaux d’emballage sont entièrement recyclables comme l’indique le symbole de recyclage ( ). Par conséquent, ne les

jetez jamais dans la nature mais conformez-vous aux réglementations locales en vigueur en matière d’élimination des déchets.

Mise au rebut de l’appareil

- Cet appareil est certifié conforme à la Directive Européenne 2002/96/CE, concernant les Déchets d’Équipements

Électriques et Électroniques (DEEE ou WEEE).

- En procédant correctement à la mise au rebut de cet appareil, vous contribuerez à empêcher toute conséquence nuisible

pour l’environnement et la santé.

- Le symbole apposé sur le produit et sur la documentation qui l’accompagne indique qu’il ne doit pas être jeté avec les

ordures ménagères, mais remis à un centre de collecte spécialisé dans le recyclage des appareils électriques et

électroniques.

Conseils pour économiser l’énergie

- Préchauffez le four uniquement si le tableau de cuisson ou votre recette le précise.

- Utilisez des moules à pâtisserie foncés, laqués noir ou émaillés, car ceux-ci absorbent très bien la chaleur.

INSTALLATION

CONSEILS POUR LA PROTECTION DE L’ENVIRONNEMENT

La page charge ...

Whirlpool AKZM 831 Le manuel du propriétaire

Marque: Whirlpool

Modèle: AKZM 831

Catégorie: Fours

Taper: Le manuel du propriétaire

Ce manuel convient également à

AKZM 831/IX

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool AKZM 831 Owner's manual

Whirlpool AKZM 831 Le manuel du propriétaire

Ce manuel convient également à

Whirlpool AKZM 831 Le manuel du propriétaire

dans d''autres langues

Documents connexes