WAC Lighting WS-7316-BN Mode d'emploi

WAC Lighting
Marque
WAC Lighting
Modèle
WS-7316-BN
Taper
Mode d'emploi

Ce manuel convient également à

WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014
INSTALLATION INSTRUCTION
Svelte - dwelLED™
WS-7316, WS-7322, WS-7334
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en posi
tion d’arrêt (« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.
HARDWARE
A1 B1 C1 N1 K1 J1 O1
Wire Connector
Qty: 3
Junction Box
Screw
Qty: 2 + 1 Extra
Mounting
Screw
Qty: 4 + 1 Extra
Screw
Qty: 2 + 1 Extra
Mounting
Anchor
Qty: 2
Wood Screw
Qty: 2
Underprop
Qty: 2
Technology Upgraded
No Driver Required
Driver
(Please direct wire with 120V AC)
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014
INSTALLATION INSTRUCTION
Svelte - dwelLED™
WS-7316, WS-7322, WS-7334
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture. Including the mounting hardware.
2. Carefully unpack your new xture and lay out all the parts on a clear area.
Be careful to lose any small parts necessary for installation.
MOUNTING THE FIXTURE
3. Remove the mounting screws (C1) from the xture.
4. Place the glass (E1) onto the xture back plate (M1). Hold using end cover (H1). Secure with screws (N1) from the xture back
plate (M1) inside.
5. Connect the electrical wires as shown in Fig, 3, making sure that all wire connectors are secured. Fixture and junction box
ground wires should be connected to mounting plate using green screw provided. After wires are connected, tuck them carefully
inside the junction box.
FOR SWITCH BOX (Fig. 1)
6. Drill holes in the wall aligned with the key-hole location in the mounting plate (I1). Insert the mounting anchors (K1).
7. Secure the mounting plate (I1) to the switch box (G1) using screws (B1). The side of the mounting plate marked
“GND” (I1) must face out.
8. Fasten the wood screws (J1) into the mounting anchors (K1). Tighten the mounting plate (I1) on the wall.
A1
G1
B1
C1
I1
K1
J1
M1
N1
H1
E1
FIG.1
Wire connector
Switch box
Screw
Mounting Screw
Mounting plate
Mounting anchors
Wood screw
Fixture back plate
Screw
End cover
Glass
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014
FOR JUNCTION BOX (Fig. 2, if necessary)
9. Secure the mounting ring (D1) to the junction box (F1) using screws (B1). Make sure the two holes (spacing 2-3/4”)
are in a horizontal direction as shown in Fig, 2.
10. Thread the underprop (O1) into the mounting plate (I1) from back.
11. Put the mounting plate (I1) and the conversion plate (P1) onto the mounting ring (D1). Make sure the two holes on mounting
plate (I1), the two slots on conversation plate (P1) and the two holes (spacing 2-3/4”) are aligned. Fasten them using screws (Z1).
12. Place the xture (M1) over the mounting plate (I1) and secure with screws (C1).
INSTALLATION INSTRUCTION
Svelte - dwelLED™
WS-7316, WS-7322, WS-7334
100%10% DIMMING
COMPATIBLE WITH THE FOLLOWING ELECTRONIC
LOW VOLTAGE ELV DIMMERS
Brand Model
LUTRON SELV-300P
LUTRON DVELV-300P
LEVITON MLE03-1
J1
O1 K1
I1
Z1
P1
B1
D1
F1
FIG.2
Junction box
Mounting
ring
Screw
Conversation
plate
Screw
Mounting
plate
Mounting
Anchor
UnderpropWood screw
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
  • Page 1 1
  • Page 2 2
  • Page 3 3

WAC Lighting WS-7316-BN Mode d'emploi

WAC Lighting
Marque
WAC Lighting
Modèle
WS-7316-BN
Taper
Mode d'emploi
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents