DELTA DORE TYXAL+ DU Guide d'installation

Taper
Guide d'installation
Contenu / Contents / Inhalt / Contenuto / Contenido / Spis treści / Inhoud
Instructions
Important
Product
Informations
FR
Le détecteur doit être associé à un système d’alarme DELTA DORE radio X3D.
EN
The detector must be associated with a DELTA DORE wireless X3D alarm system.
DE
Der Melder muss mit einer DELTA DORE Funk-Alarmanlage X3D verbunden werden.
IT
Il sensore deve essere associato ad un sistema d’allarme DELTA DORE radio X3D.
ES
El detector debe asociarse a un sistema de alarma DELTA DORE radio X3D.
PL
Detektor musi być skonfigurowany z radiowym systemem alarmowym DELTA DORE X3D.
NL
De detector moet worden gekoppeld aan een alarmsysteem DELTA DORE radio X3D.
Présentation / Presentation / Beschreibung / Presentazione / Presentación / Prezentacja
/ Voorstelling
1
LS 14250 - 3,6 V - 1,2 Ah - Lithium
Autonomie 10 ans - Autonomy 10 years
Consumption stand-by :
3,5 μA
Consumption : 14,2 mA max.
868,7 Õ 869,2 MHz - 100 m Ý 300m
Maximum power radio < 10 mW
Receiver category: 2
-10°C / +70°C
+5°C / +40°C
IP
IP 30 - IK 02
75 %
33 x 102 x 32 mm
Important product information (Ì)
www.deltadore.com
DU TYXAL+
FR
Notice d’installation
EN
Installation guide
DE
Installationsanleitung
IT
Guida di installazione
ES
Manual de instalación
PL
Instrukcja instalacji
NL
Installatiehandleiding
59 gr.
D1
D2
V1
V2
1
2 3
Fixation / Mounting / Montage / Fissaggio / Fijación / Mocowanie / Bevestiging
3
FR
Ê Séparez les 2 parties du boîtier.
Ë Tracez et percez les trous D1 et D2.
Ì Fixez le socle de l’émetteur avec les vis V1
et V2.
EN
Ê Open the unit.
Ë Mark and drill holes D1 and D2.
Ì Attach the transmitter base with the V1 and
V2 screws.
DE
Ê Öffnen Sie das Gehäuse, indem Sie die zwei
Gehäuseteile trennen.
Ë Markieren Sie die Bohrstellen und bohren
Sie die Löcher D1 und D2.
Ì Befestigen Sie den Sockel des Senders mit
den Schrauben V1 und V2.
IT
Ê Separare le 2 parti della scatola.
Ë Segnare e fare i fori D1 e D2.
Ì Fissare il supporto dell’emettitore con le viti
V1 e V2.
ES
Ê Separe las 2 partes de la caja.
Ë Marque y taladre los agujeros D1 y D2.
Ì Fije el zócalo del emisor con los tornillos V1
y V2.
PL
Ê Oddzielić 2 części obudowy.
Ë Zaznaczyć i wywiercić otwory D1 i D2.
Ì Przymocować podstawę nadajnika śrubami
V1 i V2.
NL
Ê Scheid de twee delen van de behuizing.
Ë Markeer en boor de gaten D1 en D2.
Ì Bevestig de basis van de zender met de
schroeven V1 en V2.
FR
Le détecteur universel fonctionne avec un capteur filaire. Placez l’émetteur à proximité du capteur (la
longueur de câble doit être inférieure à 2 m).
• Le détecteur universel doit être placé en intérieur.
• Pour l’emplacement et la fixation du capteur, voir sa notice.
EN
The universal detector operates with a hard-wired sensor. Install the transmitter close to the sensor
(cable length must not exceed 2 m).
The universal detector must be installed indoors.
• Refer to the guide for the location and mounting of the sensor.
DE
Der Melder arbeitet mit einem über Kabel angeschlossenen Sensor. Bringen Sie den Funksender in der
Nähe des Melders an (Kabellänge max. 2 m).
• Der Melder muss in einem Innenraum angebracht werden.
• Über Platzierung und Befestigung des Sensors gibt dessen Gebrauchsanleitung Auskunft.
IT
Il sensore universale funziona con un sensore filare. Posizionare l’emettitore vicino al sensore (la
lunghezza del cavo deve essere inferiore a 2 m).
• Il sensore universale deve essere posizionato all’interno.
• Per il posizionamento ed il fissaggio del sensore, consultare le istruzioni.
ES
El detector universal funciona con un sensor filar. Coloque el emisor cerca del sensor (la longitud del
cable debe ser inferior a 2 m).
• El detector universal se debe colocar en el interior.
• Para la colocación y fijación del sensor, consulte su manual.
PL
Detektor uniwersalny w zestawie z czujnikiem przewodowym. Umieścić nadajnik w pobliżu czujnika
(długość kabla musi być mniejsza niż 2 m).
Detektor uniwersalny musi być umieszczany wewnątrz.
Zobacz instrukcję w celu umiejscowienia i zamocowania czujnika.
NL
De universele sensor werkt met een bedrade sensor. Plaats de zender in de buurt van de sensor
(kabellengte moet minder dan 2 m bedragen).
• De universele detector moet binnen worden geplaatst.
Voor de locatie en de bevestiging van de sensor, zie de handleiding.
Emplacement / Location / Einbauort / Posizionamento / Ubicación / Lokalizacja / Locatie
2
Ø max = 3 mm
1
2
3
AL
Com
AP
1 2
Mise en service / Activation / Inbetriebnahme / Messa in funzione / Puesta en servicio /
Rozruch / Ingebruikname
4
FR
Ê Intrusion : câblez les fils de la détection d’intrusion sur les bornes AL et Com, et les fils de l’autoprotec-
tion sur les bornes AP et Com.
Technique : câblez les 2 fils du capteur de votre choix aux bornes AL et Com du détecteur universel.
La borne AP est non connectée.
Ë Mettez la pile en place en respectant son sens puis refermez le boîtier.
EN
Ê Intruder: connect the intruder alarm wires to the AL and Com terminals, and the tamper alarm wires to
the AP and Com terminals.
Other: connect the 2 wires of a sensor of your choice to the universal detector AL and Com terminals.
The AP terminal is not connected.
Ë Insert the battery and close the unit.
DE
Ê Einbruchmeldung: Schließen Sie die Leitungen des Melders an die Klemmen AL und Com an, die
Leitungen des Selbstschutzes an die Klemmen AP und Com.
Technik: Schließen Sie die beiden Drähte des Sensors Ihrer Wahl an die Klemmen AL und Com des
Universalmelders an. Die Klemme AP wird nicht belegt.
Ë Setzen Sie die Batterie unter Beachtung der Polarität ein und schließen Sie dann das Gehäuse.
IT
Ê Intrusione: collegare i fili per il rilevamento intrusione sui morsetti AL e Com, e i fili dell’autoprotezione
sui morsetti AP e Com.
Tecnica: collegare i 2 fili del sensore scelto ai morsetti AL e Com del sensore universale. Il morsetto
AP non è collegato.
Ë Posizionare la pila nel corretto senso e chiudere la scatola.
ES
Ê Intrusión: cablee los hilos de detección de intrusión en los bornes AL y Com, y los hilos de autoprotec-
ción en los bornes AP y Com.
Técnico: cablee los 2 hilos del sensor de su elección a los bornes AL y Com del detector universal. El
borne AP no se conecta.
Ë Coloque la pila respetando la polaridad y cierre la caja.
PL
Ê Wtargnięcie: połączyć przewody wykrywania wtargnięcia z końcówkami AL i Com, a przewody
samoobrony z końcówkami AP i Com.
Technika: połączyć 2 wybrane przewody czujnika z końcówkami AL i Com detektora uniwersalnego.
Końcówka AP pozostaje niepodłączona.
Ë Włożyć baterię zgodnie z polaryzacją, a następnie zamknąć obudowę.
NL
Ê Inbraak: sluit de kabels voor inbraakdetectie aan op de aansluitingen AL en Com, en de kabels voor
zelfbescherming op de aansluitingen AP en Com.
Techniek: sluit de twee kabels van de sensor van uw keuze aan op de aansluitingen AL en Com van
de universele detector. De aansluiting AP wordt niet aangesloten.
Ë Plaats de batterij in de correcte richting en sluit de behuizing.
SW
A
SW
B
SWA 1 SWA 2
SWB 1
SWB 2
SWA
ON
O
N
ON
ON
ON
ON
ON
SWB
Switchs / Switches / Schalter / Switch / Conmutadores / Wyłączniki / Schakelaars
5
FR
Les switchs SWA et SWB permettent de configurer le
produit.
EN
Switches SWA and SWB are used to configure the product.
DE
Mit den Schaltern SWA und SWB kann das Produkt
konfiguriert werden.
IT
Gli switch SWA e SWB permettono di configurare il
dispositivo.
ES
Los conmutadores SWA y SWB permiten configurar el
producto.
PL
Wyłączniki SWA i SWB pozwalają skonfigurować produkt.
NL
De schakelaars SWA en SWB worden gebruikt om het
product te configureren.
Changement de la pile /Changing the batteries /Batteriewechsel /Sostituzione delle batterie
/ Cambio de la pila / Wymiana baterii / Batterij vervangenassociations
FR
Le produit émet un bip à chaque détection, la pile est usée.
Avant d’ouvrir le boîtier, la centrale doit être en mode «Maintenance» (voir notice d’installation système).
EN
The product beeps with every detection, the battery is dead.
Before opening the unit, the alarm control unit must be in Maintenance mode (refer to system installation
guide).
DE
Das Gerät piept bei bei jeder Erfassung, die Batterie ist leer.
Die Alarmzentrale muss sich beim Öffnen des Gehäuses im Wartungsmodus befinden (siehe
Installationsanleitung System).
IT
Se il dispositivo emette un bip ad ogni rilevamento, la pila è esaurita.
Prima di aprire la scatola, la centralina deve essere in modalità “Manutenzione” (vedi istruzioni per
l’istallazione del sistema).
ES
El producto emite un pitido en cada detección, la pila se agota.
Antes de abrir la caja, la central debe estar en modo “Mantenimiento” (consultar el manual de instalación
del sistema).
PL
Produkt wydaje krótki dźwięk przy każdym wykryciu: bateria jest wyczerpana.
Przed otwarciem obudowy centrala musi być przełączona na tryb konserwacji (zob. instrukcja instalacji
systemu).
NL
Het product geeft een pieptoon wanneer de batterij bijna leeg is.
Voor het openen van de behuizing, moet het apparaat in de onderhoudsmodus worden geplaatst (zie
installatiehandleiding van het systeem).
7
FR
Si votre système d’alarme est équipé d’un clavier tactile CLT 8000, le switch SWB2 est ignoré car cette
configuration est réalisée sur celui-ci.
EN
If your alarm system has a CLT 8000 touch sensitive keypad, switch SWB2 will be ignored as this
configuration is done on the keypad.
DE
Wenn Ihre Alarmanlage mit der Touchscreen-Tastatur CLT 8000 ausgerüstet ist, erfolgt die Konfiguration
über diese, der Schalter SWB2 ist dann außer Funktion.
IT
Se il vostro sistema d’allarme è dotato di tastiera tattile CLT 8000, lo switch SWB2 viene ignorato perché
questa configurazione viene eseguita su di esso.
ES
Si su sistema de alarma está equipado con un teclado táctil CLT 8000, el conmutador SWB2 se ignora
puesto que esta configuración se lleva a cabo sobre el mismo.
PL
Jeżeli Twój system alarmowy jest wyposażony w klawiaturę dotykową CLT 8000, wyłącznik SWB2
należy zignorować, ponieważ konfigurację przeprowadza się za pomocą klawiatury.
NL
Als uw alarmsysteem is uitgerust met het touchscreen toetsenbord CLT 8000, dan wordt schakelaar
SWB2 genegeerd omdat deze configuratie door het toetsenbord wordt uitgevoerd.
Fonctionnement avec un système d’alarme / Operation with an alarm system / Betrieb mit
einer Alarmanlage / Funzionamento con un sistema d’allarme / Funcionamiento con el
sistema de alarma / Działanie z systemem alarmowym / Werking met alarmsysteem
6
FR
• Association avec un système d’alarme
• Choix du mode de déclenchement
• Test
• Retour à la configuration usine
Voir notice
d’intallation
système
EN
• Association with an alarm system
• Selection of triggering mode
• Test
• Restoring factory settings
DE
Verbindung mit einer Alarmanlage
Wahl des Auslösungsmodus
• Test
• Rückkehr zur Werkseinstellung
IT
• Associazione con un sistema d’allarme
• Scelta della modalità di scatto dell’allarme
• Test
• Ritorno alla configurazione di fabbrica
ES
• Asociación con el sistema de alarma
• Elección del modo de activación
• Prueba
Volver a la configuración de serie
PL
• Powiązanie z systemem alarmowym
Wybór sposobu wyzwalania
• Test
• Przywrócenie konfiguracji fabrycznej
NL
• Koppelen aan een alarmsysteem
• Activeringsmodus selecteren
• Test
• Fabrieksinstellingen herstellen
Refer to system
installation
guide
Siehe
Installationsanleitung
System
Vedi le istruzioni
di installazione
«Sistema»
Ver manual
de instalación
del sistema
Patrz instrukcja
instalacji
systemu
Zie
installatiehandleiding
systeem
SWA 1 = ON
(Détection technique / Detection / Technischer
Alarm / Rilevamento tecnico / Detección técnica /
Wykrywanie techniczne / Detectoren)
SWA 1 = OFF
(Détection intrusion / Intruder detection / Einbruchmeldung /
Rilevamento intrusione / Detección de intrusión / Wykrywanie
wtargnięcia / Inbraakdetectie)
SWA
2
ON OFF ON OFF
Normalement fermé /
Normally closed /
Normal geschlossen /
Normalmente chiuso /
Normalmente cerrado /
Normalnie zamknięte /
Normaal gesloten
Normalement ouvert /
Normally open /
Normal offen /
Normalmente aperto /
Normalmente abierto /
Normalnie otwarte /
Normaal open
Normalement fermé /
Normally closed /
Normal geschlossen /
Normalmente chiuso /
Normalmente cerrado /
Normalnie zamknięte /
Normaal gesloten
Normalement ouvert /
Normally open /
Normal offen /
Normalmente aperto /
Normalmente abierto /
Normalnie otwarte /
Normaal open
SWB
1
ON OFF
Autoprotection inactive /
Tamper alarm inactive /
Selbstschutz eingeschaltet /
Autoprotezione non attiva /
Autoprotección inactiva /
Samoobrona nieaktywna /
Zelfbescherming inactief
Autoprotection active /
Tamper alarm active /
Selbstschutz ausgeschaltet /
Autoprotezione attiva /
Autoprotección activa /
Samoobrona aktywna /
Zelfbescherming actief
SWB
2
ON OFF
Retardé /
Delayed /
Verzögert /
Ritardato /
Retardado /
Opóźniony /
Vertraagd
Immédiat /
Immediate /
Sofort /
Immediato /
Inmediato /
Natychmiastowy /
Onmiddellijk
1 / 1

DELTA DORE TYXAL+ DU Guide d'installation

Taper
Guide d'installation