VTech VM333 Manuel utilisateur

Marque: VTech

Modèle: VM333

Catégorie: Moniteurs vidéo bébé

Taper: Manuel utilisateur

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has all the feature operations

and troubleshooting necessary to install and

operate your new VTech product. Please

review this manual thoroughly to ensure

proper installation and operation of this

innovative and feature rich VTech product.

For support, shopping, and everything new at

VTech, visit our website at

www.vtechphones.com.

What’s in the box

1 set for VM333

2 sets for VM333-2

Install the battery

The parent unit runs on rechargeable battery

or AC power. To continuously monitor your

baby, make sure you use both battery and

AC power at the same time. With the battery

alone, the parent unit can cordlessly run for a

short time only.

NOTES

Use only the battery supplied with this product.

The operating time for using the rechargeable

battery is short. If you want to monitor your baby

for a long time, we recommend you connect the

parent unit to AC power.

If the parent unit will not be used for a long time,

disconnect and remove the battery to prevent

possible leakage.

Install the battery as shown below.

NOTES

Press down on the large tab of the battery

compartment cover to pull it out.

THIS SIDE UP

NOTES

Make sure the label THIS SIDE UP is facing up

while inserting the battery.

Replace the battery

To replace the battery, press down on the

large tab of the battery compartment cover

and pull it out, then follow the steps above to

install the battery.

•

Connect and charge the

battery

NOTES

Use only the power adapters supplied with this

product.

Make sure the electrical outlets are not controlled

by wall switches.

The power adapters are intended to be correctly

oriented in a vertical or ﬂoor mount position. The

prongs are not designed to hold the plug in place

if they are plugged into a ceiling, under-the-table

or cabinet outlet.

Make sure the parent unit, the baby unit and the

power adapter cords are out of reach of children.

Connect the baby monitor

•

Charge the parent unit battery

When you have connected the parent unit and

installed its battery, press and hold to turn

on the parent unit. The battery icon indicates

the battery status (see the following table).

NOTES

The parent unit battery is fully charged after

12 hours of continuous charging.

It takes longer to charge the battery when the

parent unit is turned on. To shorten the charging

time, turn the parent unit off while charging.

The standby time varies depending on the

sensitivity level you set, your actual use and the

age of the battery.

Battery

indicators

Battery

status

Action

The battery

icon is off

and

displays.

No battery

is installed

but operates

using AC

power, or the

battery has

been installed

incorrectly.

Install the

parent unit

battery.

Charge

without

interruption

(at least

30 minutes).

The screen

displays

Battery low

and . The

light

ﬂashes.

The battery

has very little

charge and

may be used

for only a

short time.

Charge

without

interruption

(about

30 minutes).

The battery

icon

becomes

solid .

The battery is

fully charged.

To keep

the battery

charged,

connect it to

AC power

when not in

use.

•

Before use

NOTE

This baby monitor is intended as an aid. It is not a

substitute for proper adult supervision, and should

not be used as such.

Test your baby monitor

You may test the baby monitor before initial

use, and at regular times thereafter.

CAUTION

For hearing protection, make sure the parent

unit is more than 1 meter (3 feet) away from

the baby unit. If you hear any high-pitched

noise, move the parent unit further until the

noise stops. You can also press VOL and

then or on the parent unit to lower or

mute the noise.

63℉

> 1m (3ft)

Make sure your baby units and parent unit

are on.

The parent unit displays images from the

baby unit.

Speak towards the baby unit microphone.

You will hear the sound at the parent

unit.

If you have more than one baby unit, press

VIEW on your parent unit. The screen

switches to other baby units. Then, repeat

step 2.

NOTE

When the parent unit displays No link, and

the LINK LED light ﬂashes, move the parent unit

closer to the baby unit (observe the minimum

distance of 1 meter/ 3 feet). You can also check

if the baby monitor is connected to a live power

socket and switched on.

TIP

Increase the parent unit speaker volume if you

cannot hear the sounds transmitted from the baby

unit.

•

Positioning the baby monitor

CAUTION

Keep the baby units out of the reach of your baby.

Never place or mount the baby units inside the

baby’s crib or playpen.

NOTE

To avoid interference from other electronic

devices, place your baby monitor far away from

devices such as wireless routers, microwaves,

cell phones and computers.

Place the baby units more than 1 meter

(3 feet) away from your baby.

More than 1 meter

(3 feet)

> 1m (3ft)

2. Place the parent unit more than 1 meter

(3 feet) away from the baby units.

> 1m (3ft)

< 1m (3ft)

63ē

CAUTION

If you experience high-pitched screeching noise

from your baby monitor while positioning:

Make sure your baby units and parent unit are

more than 1 meter (3 feet) apart, OR

Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is

up to 300 meters (1,000 feet) outdoors or

50 meters (160 feet) indoors. The actual

operating range may vary depending on

the environmental conditions and other

interferences such as walls, doors and other

obstructions.

•

Overview

Baby unit overview

1Light sensor

2Infrared LEDs

3Camera

4Microphone

5Speaker

6Antenna

7Power jack

8Temperature sensor

9ON/OFF LED light

On when the baby unit is turned on

and is paired to the parent unit.

Flashes when the baby unit is not

being viewed; or when the link to the

parent unit is lost.

•

10 ON/OFF switch

Slide to turn on or off the baby unit.•

11 -/VOL/+

Press to adjust the baby unit speaker

volume. It determines the talkback

volume transmitted from parent unit.

•

12 PAIR

Your baby units and parent unit

provided are already paired.

Press and hold on accessory baby

units (VM303, purchased separately)

to pair to the parent unit.

•

13 Threaded socket

For wall mount installation use.•

Parent unit overview

1MIC (Microphone)

2VOL

Press to enter the parent unit speaker

volume adjustment mode.

•

3 Zoom

Press to zoom in or out while viewing

image in Single Baby unit mode or

Patrol Mode.

•

4 LED lights

Indicate the different statuses of

the parent unit. For details, refer to

Parent unit lights.

•

5 LCD display

While in a menu, press to choose an

item.

While in Single Baby unit mode or

Patrol Mode, press and hold to move

the baby unit camera leftward.

While in Split Baby unit mode, press

to move the selection box leftward.

•

While in a menu, press to scroll up.

While in Single Baby unit mode or

Patrol Mode, press and hold to move

the baby unit camera upward.

While in Split Baby unit mode, press

to move the selection box upward.

•

8MENU/SELECT

Press to enter the menu.

While in a menu, press to choose an

item, or save a setting.

•

While in a menu, press to choose an

item.

While in Single Baby unit mode or

Patrol Mode, press and hold to move

the baby unit camera rightward.

While in Split Baby unit mode, press

to move the selection box rightward.

•

While in a menu, press to scroll down.

While in Single Baby unit mode or

Patrol Mode, press and hold to move

the baby unit camera downward.

While in Split Baby unit mode, press

to move the selection box downward.

•

Press to change the screen to view

images from different baby units.

•

12 Speaker

13 TALK

Press and hold to talk to the selected

baby unit in Single Baby unit mode

or Patrol Mode.

•

14 Antenna

15 On/off

Press and hold to power on.

Press and hold again to power off.

•

16 Power jack

17 Stand

Parent unit lights

LINK On when the parent unit is linked to

the baby unit.

Flashes when the link to the baby

unit being viewed in Single Baby

unit mode or Patrol Mode is lost;

or when the link to all baby units

being viewed in Split Baby unit

mode is lost.

On when the parent unit is

connected to AC power, or the

battery is charging.

Flashes when the parent unit

battery is low and needs charging.

Off when the parent unit is

disconnected from AC power.

TALK On when the parent unit is talking to

the baby unit.

On when the speaker volume of the

parent unit is turned off.

Parent unit display icons

Connection status

displays when strong signal

strength is detected between the

baby unit and the parent unit.

or displays when moderate

signal strength is detected

between the baby unit and the

parent unit.

displays when the link between

the baby unit and the parent unit

is lost.

•

Current view status

Displays the number of the baby

unit that is being viewed when in

Single Baby unit.

Displays the highlighted baby unit

when in Patrol Mode.

•

Zoom

Displays when the camera at the

baby unit has zoomed in.

•

Temperature alert

Displays when the temperature

alert is set to on.

•

oF or

Real-time temperature

Displays the real-time

temperature detected by the baby

unit in Fahrenheit (oF) or Celcius

(oC)(e.g. 57 oF or 14 oC).

•

Sound level indicators

isplays the sound level according

to the scales of loudness when

there is sound transmitted from

the baby unit.

Speaker volume off

Displays the speaker volume of

the parent unit is turned off.

Speaker volume

Displays the speaker volume level

while adjusting.

•

Battery status

animates when the battery is

charging.

displays solid when the

battery is fully charged.

displays when the battery is

low and needs charging.

displays when no battery is

installed but operates using AC

power, or the battery has been

installed incorrectly.

•

Parent unit main menu icons

Monitoring mode

You can choose to monitor in

Single Baby unit, Split Baby unit or

Patrol Mode if there are more than

one baby units in your system.

Language

You can select a language (English,

French or Spanish) to be used in all

screen displays.

Display

You can change the brightness of

the parent unit screen.

You can change the contrast of

the parent unit screen.

•

Alert tone

You can set whether the parent

unit beeps whenever the parent

unit operates in low battery

condition.

You can set whether the parent

unit beeps whenever the link

between the parent unit and the

baby unit is lost.

You may turn on the sound alert

so that the parent unit beeps as

soon as the baby unit detects

sounds which light up four sound

level indicators on the parent unit

when the parent unit volume is

turned off manually.

•

Temperature

You can set the desired minimum

room temperature of the baby

unit.

You can set the desired

maximum room temperature of

the baby unit.

You can set whether the parent

unit beeps whenever the

temperature is out of the preset

temperature range.

You can set the temperature

scale of the baby unit.

•

Sensitivity

You can use the parent unit to

change the sound sensitivity

level of the baby units.

•

Sound activation

You can set the screen to

be turned on automatically

whenever there are sounds

detected from the baby units

when the parent unit screen is

turned off manually.

•

Vibration

You may turn on the vibration

alert so that the parent unit

vibrates as soon as the baby unit

detects sounds which light up

three sound level indicators on

the parent unit.

•

Pair/unpair

The baby units and parent unit

provided are already paired. You

can add or replace baby units

(VM303, purchased separately)

to your baby monitor system.

•

Parent unit display messages

Battery low

When the parent unit

is powered by the

rechargeable battery and

the battery level is low, it

needs to be recharged.

Failed to

connect

The parent unit fails to

switch to the next baby

unit in Single Baby unit or

Patrol Mode.

No Link

The selected baby unit slot

is not linked to the parent

unit.

Pairing failed

The selected baby unit

cannot be paired with the

parent unit.

Conﬁrm to

unpair?

You try to unpair the baby

unit(s). The operation

needs your conﬁrmation.

Pairing

completed

The selected baby unit

has been paired with the

parent unit.

Unpairing

completed

The selected baby unit(s)

has been unpaired with the

parent unit.

Please Wait...

The link between the

parent unit and the

selected baby unit is lost,

or the selected baby unit

is out of range, or the

selected baby unit slot is

empty.

When you have only one

paired baby unit and the

link is lost, or you have

multiple paired baby units

and the links are lost.

Temperature

too low

The temperature detected

from the selected baby unit

is below the set minimum

temperature.

Temperature

too high

The temperature detected

from the selected baby unit

is above the set maximum

temperature.

Using the baby monitor

Power on or off the baby unit

Slide ON/OFF switch to the left to turn

on the baby unit. The ON/OFF LED light

turns on.

Slide ON/OFF switch to the right to turn

off the baby unit. The ON/OFF LED light

turns off.

Power on or off the parent unit

Press and hold to turn on the parent unit.

The LINK light turns on.

Press and hold again to turn off the

parent unit. The LINK light turns off.

Turn on or off the parent unit

screen

You can turn on or off the parent unit screen

without powering off the parent unit. You can

still hear sound from the baby unit.

Press on the parent unit at any time.

Adjust speaker volume

For parent unit:

Press VOL when the parent unit is not

in use.

Press , , or to adjust the speaker

volume.

NOTE

When the parent unit speaker volume is set to

zero, appears brieﬂy and the light

turns on.

For baby unit:

The baby unit speaker volume determines the

talkback volume transmitted from your parent

unit.

Press +/VOL or -/VOL on the baby unit at

any time.

•

Set the language

You can select a language (English, French or

Spanish) to be used in all screen displays.

Press MENU when the parent unit is idle.

Press or to choose LANGUAGE.

Press or to choose English, Français

or Español.

Adjust LCD brightness

You can change the brightness of the parent

unit screen from Level 1 to Level 5.

Press MENU when the parent unit is idle.

Press or to choose DISPLAY, then

press SELECT.

When Brightness is highlighted, press

or to choose the desired level of

brightness, then press SELECT to conﬁrm

your selection.

Adjust LCD contrast

You can change the contrast of the parent unit

screen from Level 1 to Level 5.

Press MENU when the parent unit is idle.

Press or to choose DISPLAY, then

press SELECT.

Press or to choose Contrast.

Press or to choose the desired level

of contrast, then press SELECT to conﬁrm

your selection.

Adjust the sound sensitivity of

the baby units

You can choose to hear sounds from the

baby units all the time, or to hear sounds

that exceed a certain level. You can use the

parent unit to adjust the microphone sensitivity

of your baby units from Level 1 to Level 5.

The higher the sensitivity level, the more

sensitive the baby unit is in detecting sounds

for transmitting to the parent unit. The sound

sensitivity level is preset to Level 5.

Sound sensitivity table for reference

Display Sensitivity Description

Level 5 High

sensitivity

Low

sensitivity

High sensitivity level

The parent unit speaker

is constantly on, and

you will hear all sounds

(including background

noises) from your baby’s

room.

Level 4 Medium high

sensitivity level

The parent unit speaker

turns on for soft babbling

and louder sounds from

your baby. It remains

quiet when your baby

sleeps soundly.

Level 3 Medium sensitivity

level

The parent unit speaker

turns on for loud babbling

and louder sounds from

your baby. It remains quiet

when your baby makes

soft sounds.

Level 2 Medium low sensitivity

level

The parent unit speaker

turns on for crying and

louder sounds from your

baby. It remains quiet

when your baby makes

soft sounds.

Level 1 Low sensitivity level

The parent unit speaker

turns on for loud crying or

screeching sounds from

your baby. It remains quiet

when your baby makes

soft sounds.

Press MENU when the parent unit is idle.

Press or to choose SENSITIVITY,

then press SELECT.

If you have more than one baby unit,

the system prompts you to choose the

desired baby unit or all baby units, press

or to choose a desired baby unit or

all baby units.

Press or to choose the desired

sensitivity level, then press SELECT to

conﬁrm your selection.

TIP

You can adjust the baby unit placement to

improve the sound detection.

Turn on or off the sound

activation

When sound activation is on, as long as no

sound is detected within 50 seconds, the

parent unit screen will turn off automatically to

save power.

When your baby unit detects a sound, the

sound activation triggers the parent unit

screen to turn on automatically. When no

sound is detected within 50 seconds, the

screen will be off again.

Press MENU when the parent unit is idle.

Press or to choose SOUND

ACTIVATION.

Press or to choose On or Off.

NOTE

If the sound sensitivity is set to Level 5, the

parent unit screen may remain on continuously

even though sound activation is on.

•

User’s manual

VM333

VM333-2

Safe & Sound®

Pan & Tilt Full Color

Video Monitor

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

Monitoring mode

You can choose to monitor in Single Baby

unit, Split Baby unit or Patrol Mode if there

are more than one baby units in your system.

To change the monitoring mode:

Press MENU when the parent unit is idle.

Press or to choose MONITORING

MODE, then press SELECT to select.

Press or to choose Single Baby unit,

Split Baby unit or Patrol Mode.

Single Baby unit - Press or to

choose a desired baby unit. The parent

unit only displays image of one baby unit.

You may change to view images from

different baby units by pressing in

this mode.

Split Baby unit - The parent unit

displays multiple baby unit images in a

maximum of four in one screen. If there

are more than four baby units in your

system, images will be shown on two split

screens, which alternates with each other

automatically.

Patrol Mode - The parent unit patrols to

display images from different baby units

in every 7 seconds. You may change to

view images from different baby units

even though the scanning period is not

expired by pressing in this mode.

Press SELECT to conﬁrm your selection.

NOTES

Monitoring mode is not applicable when there is

only one baby unit.

•

View

You can change the screen to view images

from different baby units.

To view different baby units while in Single

Baby unit:

Press repeatedly to switch to the desired

baby unit. The switching is in chronological

order: Baby unit 1 to Baby unit 4.

To view different baby units while in Split

Baby unit:

Press repeatedly to enlarge and switch

to the desired baby unit. The switching is in

chronological order: Baby unit 1 to Baby unit

4. The Split Baby unit mode resumes after

a while.

To view different baby units while in Patrol

mode:

Press repeatedly to switch to the desired

baby unit even if the scanning period on

a particular baby unit is not expired. The

switching is in chronological order: Baby unit

1 to Baby unit 4.

NOTES

If the switching fails, the screen displays Failed to

connect. Try the switching again.

Pan, tilt, zoom

You can remotely pan and tilt your baby unit

camera or zoom in while viewing images in

Single Baby unit mode and Patrol Mode.

Press and hold , , or to move the

baby unit camera upward, downward,

leftward or rightward correspondingly.

Press to zoom in. Press again to zoom

out.

Talk

You can use the TALK function of the parent

unit to comfort your baby in Single Baby unit

mode and Patrol Mode.

Press and hold TALK on the parent unit.

The TALK light turns on.

Speak towards the MIC (microphone) on

the parent unit. Your voice is broadcast to

the baby unit.

Release the TALK key to stop the

broadcast. The TALK light goes off.

•

Set alert tone

Low battery tone

You can set the parent unit to beep when the

parent unit operates in low battery condition.

Press MENU when the parent unit is idle.

Press or to choose ALERT TONE,

then press SELECT.

When Low Battery Tone is highlighted,

press or to choose On or Off, then

press SELECT to conﬁrm your selection.

No link alert

You can set the parent unit to beep when the

link between the parent unit and the baby unit

is lost.

Press MENU when the parent unit is idle.

Press or to choose ALERT TONE,

then press SELECT.

Press or to choose No Link Alert.

Press or to choose On or Off, then

press SELECT to conﬁrm your selection.

Sound alert

When the parent unit volume is turned off

manually, you may turn on the sound alert so

that the parent unit beeps as soon as the baby

unit detects sounds which light up four sound

level indicators on the parent unit.

Press MENU when the parent unit is idle.

Press or to choose ALERT TONE,

then press SELECT to select.

Press or to choose Sound alert.

Press or to choose On or Off, then

press SELECT to conﬁrm your selection.

NOTES

The sound alert feature is only available in

Split Baby unit mode.

•

Monitor the temperature

Your baby unit monitors the temperature of

your baby’s room with its built-in temperature

sensor. If the detected temperature is outside

of the preset temperature range, the parent unit

will display alert message.

Set temperature range

You can set the desired room temperature

alert range. The minimum temperature can be

set between 52 oF (11 oC) and 69 oF (20 oC).

The maximum temperature can be set

between 70 oF (21 oC) and 86 oF (30 oC).

Press MENU when the parent unit is idle.

Press or to choose TEMPERATURE,

then press SELECT.

Press or to choose Minimum or

Maximum, then press SELECT.

If you have more than one baby unit,

the system prompts you to choose the

desired baby unit or all baby units, press

or to choose a desired baby unit or

all baby units.

Press or to choose the desired

minimum or maximum temperature, then

press SELECT to conﬁrm your selection.

Temperature alert tone

You can turn on the temperature alert tone so

that the parent unit will emit an alert tone if the

detected temperature is out of range.

Press MENU when the parent unit is idle.

Press or to choose TEMPERATURE,

then press SELECT.

Press or to choose Alert Tone, then

press SELECT.

If you have more than one baby unit,

the system prompts you to choose the

desired baby unit or all baby units, press

or to choose a desired baby unit or

all baby units.

Press or to choose On or Off, then

press SELECT to conﬁrm your selection.

Temperature format

You can choose to display the temperature in

Fahrenheit (oF) or Celcius (oC).

Press MENU when the parent unit is idle.

Press or to choose TEMPERATURE,

then press SELECT.

When Format is highlighted, press or

to choose oF or oC, then press SELECT to

conﬁrm your selection.

•

Turn on or off the vibration

You may turn on the vibration alert so that the

parent unit vibrates as soon as the baby unit

detects sounds which light up three sound

level indicators on the parent unit.

To change the vibration setting:

Press MENU when the parent unit is idle.

Press or to choose VIBRATION, then

press SELECT to select.

Press or to choose On if speaker is

off, Always on or Off.

On if speaker is off - The parent unit

vibrates once whenever the baby units

detect sounds which light up three sound

level indicators while the speaker of the

parent unit is turned off.

Always on - The parent unit vibrates

once whenever the baby units detect

sounds which light up three sound level

indicators.

Off - The parent unit will not vibrate even

if the baby units detect sounds.

Press SELECT to conﬁrm your selection.

NOTES

If you set the sensitivity level to Level 5, the baby

unit will be very sensitive and detect any sounds

including background noises. These background

noises may disrupt the silence and prevent the

vibration feature to work properly.

Night vision

To help you monitor your baby even at night,

the baby unit automatically uses the light from

its infrared LEDs for transmitting images to the

parent unit when it is turned on in a dark room.

However, it only transmits black-and-white

images.

Pair new baby unit (VM303)

The baby units and parent unit provided are

already paired. You can add or replace any

baby units (VM303, purchased separately)

to your video and audio monitor system. You

can pair a maximum of four baby units to your

parent unit.

For more details, refer to the user’s manual

that comes with your VM303 new baby unit.

•

General product care

To keep this product working well and looking good,

follow these guidelines:

Avoid putting it near heating appliances and devices

that generate electrical noise (for example, motors or

ﬂuorescent lamps).

DO NOT expose it to direct sunlight or moisture.

Avoid dropping the product or treating it roughly.

Clean with a soft cloth.

DO NOT immerse the parent unit and the baby

unit in water and do not clean them under the tap.

DO NOT use cleaning spray or liquid cleaners.

Make sure the baby unit and parent unit are dry

before you connect them to the mains again.

Storage

When you are not going to use the baby monitor for

some time, remove the rechargeable battery from

the parent unit. Store the parent unit, the baby unit

and the adapters in a cool and dry place.

•

Frequently asked questions

Below are the questions most frequently asked about

the baby monitor. If you cannot ﬁnd the answer to your

question, visit our website at www.vtechphones.com,

or contact 1 (800) 595-9511 for customer service.

Why does the

baby monitor

not respond

normally?

Try the following (in the order

listed) for common cure:

1. Disconnect the power to the

baby units and the parent unit.

2. Remove the batteries in the

parent unit. Then install the

batteries again.

3. Wait a few seconds before

connecting power back to the

baby units and the parent unit.

4. Turn on the baby units and the

parent unit.

5. Wait for the parent unit to

synchronize with the baby

units. Allow up to one minute for

this to take place.

Why don’t

the power-on

light of the

baby unit and

parent unit

go on when I

switch on the

units?

Perhaps the parent unit is not

connected to the mains. Insert

the appliance plug into the parent

unit and put the adapter in a wall

socket. Then press and hold

to switch on the parent unit and

to establish connection with the

baby unit.

Perhaps the baby unit is not

connected to the mains. Connect

the baby unit to the mains. Then

set the ON/OFF switch to ON

to switch on the baby unit and

to establish connection with the

parent unit.

Why doesn’t

my parent unit

charge while

connected to

AC power?

Make sure the power is not

controlled by a wall switch.

Make sure the battery is correctly

installed in your parent unit.

You may have used the battery

for a long time. Replace a new

battery.

Why is my

screen in

black and

white?

The screen is in black and white

during nighttime or in a dark

room. This is normal due to

external light sources.

Why do I get

glare or blurry

display on my

screen when

viewing my

baby at night?

During nighttime or in a dark

room, the surroundings and other

interfering factors, like lightings,

objects, colors and backgrounds

may affect the image quality on

your parent unit screen. Adjust

the baby unit’s angle or place

the baby unit at a higher level to

prevent glare and blurry display.

Why does the

baby monitor

produce a

high-pitched

noise?

The parent unit and baby units

may be too close to each other.

Move the parent unit away

from the baby units until the

noise stops; OR

Turn down the volume of your

parent unit.

•

The ON/OFF

light on the

baby unit

ﬂashes and

the parent unit

displays .

The baby unit is unpaired from

the parent unit. Follow below

steps to pair the baby unit. Make

sure both parent unit and baby

unit are on before pairing.

Press MENU when the parent

unit is idle.

Press or to choose

PAIR/UNPAIR, then press

SELECT.

Press SELECT again to

choose Pair Baby unit.

Press or to choose an

empty baby unit slot, then

press SELECT.

The parent unit screen

displays Press and hold

PAIR on Baby Unit to

start Pairing. Immediately

press and hold PAIR on the

bottom of the baby unit.

Parent unit screen displays

Pairing...Please Wait...

and emits beep sound every

two seconds The LED light

ﬂashes quickly.

When pairing is successful,

the screen displays Pairing

completed. You hear a

conﬁrmation tone. The LED light

on the new baby unit turns green.

The parent unit returns to the

previous menu

If pairing fails, the screen

displays Pairing failed. Try the

pairing process again.

Only one baby unit can be

paired at a time.

•

Why does the

parent unit

beep?

The baby units may be out of

range. Move the parent unit

closer to the baby units (but not

less than 3 feet).

If the parent unit is powered

by the provided battery, it may

not have enough charge for the

parent unit to perform normally.

Charge the battery in the parent

unit for up to 12 hours.

If your parent unit is in

Split Baby unit mode, some

of your baby units may detect

sounds.

The temperature of your baby’s

room may be too high or too low.

Why does the

parent unit

beep/vibrate

frequently?

You may have set the sound

sensitivity level to Level 5 when

the sound alert (and vibration)

feature are turned on. The parent

unit notiﬁes you of all sounds

including background noise with

beeps (or vibrations). Adjust the

sound sensitivity to a lower level.

Why does

the parent

unit react too

quickly to

other sounds?

The baby unit also picks up other

sounds than those of your baby.

Adjust the sensitivity level to a

lower level or lower the parent

unit speaker volume.

Why don’t I

hear a sound/

Why can’t I

hear my baby

cry?

The parent unit speaker volume

may be too low or off. Press VOL

follow by , , or to increase

the volume.

You may have set a low sound

sensitivity level. See Adjust the

sound sensitivity of the baby

unit to set to a higher level.

Why can’t I

establish a

connection?

Why is the

connection

lost every now

and then?

Why are

there sound

interruptions?

The baby units may be out of

range. Move the parent unit

closer to the baby units

(observe the minimum distance

of 1 meter/ 3 feet).

Other electronic products may

cause interference with your baby

monitor. Try installing your baby

monitor as far away from these

electronic devices as possible.

Important safety

instructions

When using your equipment, basic safety precautions

should always be followed to reduce the risk of ﬁre,

electric shock and injury, including the following:

Follow all warnings and instructions marked on

the product.

Adult setup is required.

This product is intended as an aid. It is not

a substitute for responsible and proper adult

supervision and should not be used as such.

This product is not intended for use as a medical

monitor.

Do not use this product near water. For example,

do not use it next to a bath tub, wash bowl,

kitchen sink, laundry tub or swimming pool, or in

a wet basement or shower.

CAUTION: Use only the batteries indicated in

this manual. There may be a risk of explosion

if a wrong type of battery is used for the parent

unit. Use only the supplied rechargeable battery

or replacement battery pack (BT198555/

BT298555) for the parent unit. Do not dispose of

batteries in a ﬁre. They may explode. Dispose of

used battery according to the information in The

RBRC® seal.

Use only the adapters included with this product.

Incorrect adapter polarity or voltage can

seriously damage the product.

Baby unit power adapter: Output: 5.9V DC 1A

Parent unit power adapter: Output: 6V DC 800mA.

For pluggable equipment, the socket-outlet shall

be installed near the equipment and shall be

easily accessible.

The power adapters are intended to be correctly

oriented in a vertical or ﬂoor mount position. The

prongs are not designed to hold the plug in place

if it is plugged into a ceiling, under-the-table or

cabinet outlet.

Unplug this product from the wall outlet before

cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.

Unplug the power cords before replacing batteries.

Do not cut off the power adapters to replace

them with other plugs, as this causes a

hazardous situation.

Do not allow anything to rest on the power cords.

Do not install this product where the cords may

be walked on or crimped.

This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply in your home, consult your dealer or local

power company.

Do not overload wall outlets or use an extension

cord.

Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

10.

11.

12.

13.

14.

15.

This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a soft

surface such as a bed, sofa or rug. This product

should never be placed near or over a radiator or

heat register.

Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short circuit.

Never spill liquid of any kind on the product.

To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than speciﬁed

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

You should test the sound reception every

time you turn on the units or move one of the

components.

Periodically examine all components for damage.

Be aware of possible loss of privacy while using

public airwaves. Conversations may be picked

up by other nursery monitors, cordless phones,

scanners, etc.

Children should be supervised to ensure that

they do not play with the product.

The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety.

SAVE THESE INSTRUCTIONS

Cautions

Use and store the product at a temperature

between 32oF and 104oF.

Do not expose the product to extreme cold, heat

or direct sunlight. Do not put the product close to

a heating source.

Batteries should not be exposed to excessive

heat such as bright sunshine or ﬁre.

Make sure the baby unit(s) and the adapter

cord(s) are always out of reach of the baby, at

least 3 feet away from the baby or crib, to avoid a

possible strangulation hazard.

Never place the baby unit(s) inside the baby’s crib

or playpen. Never cover the baby unit(s) or parent

unit with anything such as a towel or a blanket.

Other electronic products may cause

interference with your baby monitor. Try

installing your baby monitor as far away

from these electronic devices as possible:

wireless routers, radios, cellular telephones,

intercoms, room monitors, televisions,

personal computers, kitchen appliances and

cordless telephones.

16.

17.

18.

19.

20.

21.

22.

23.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital cordless

devices):

Wireless Technology Research, LLC (WTR), an

independent research entity, led a multidisciplinary

evaluation of the interference between portable

wireless devices and implanted cardiac

pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

Should keep wireless devices at least six inches

from the pacemaker.

Should NOT place wireless devices directly over

the pacemaker, such as in a breast pocket, when

it is turned ON.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless devices.

Electromagnetic fields (EMF)

This VTech product complies with all standards

regarding electromagnetic ﬁelds (EMF). If handled

properly and according to the instructions in this

user’s manual, the product is safe to be used based

on scientiﬁc evidence available today.

The RBRC® seal

The RBRC® seal on the lithium-ion battery indicates

that VTech Communications, Inc. is voluntarily

participating in an industry program to collect and

recycle these batteries at the end of their useful

lives, when taken out of service within the United

States and Canada.

The RBRC® program provides a convenient

alternative to placing used lithium-ion batteries into

the trash or municipal waste, which may be illegal in

your area.

VTech’s participation in RBRC® makes it easy for

you to drop off the spent battery at local retailers

participating in the RBRC® program or at authorized

VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Li-ion

battery recycling and disposal bans/restrictions in

your area. VTech’s involvement in this program is

part of its commitment to protecting our environment

and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY®

are registered trademarks of the

Rechargeable Battery Recycling

Corporation.

•

FCC and IC regulations

FCC Part 15

This equipment has been tested and found to

comply with the requirements for a Class B digital

device under Part 15 of the Federal Communications

Commission (FCC) rules. These requirements are

intended to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to

try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment

and receiver.

Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV

technician for help.

WARNING: Changes or modiﬁcations to this

equipment not expressly approved by the party

responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established

criteria for the amount of radio frequency energy

that can be safely absorbed by a user or bystander

according to the intended usage of the product. This

product has been tested and found to comply with

the FCC criteria. The baby unit shall be installed

and used such that parts of all persons’ body are

maintained at a distance of approximately 8 in (20

cm) or more. The transmitter and antenna of the

parent unit shall be held at least 1 in (2.5 cm) from

your face.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

•

Industry Canada

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference,

including interference that may cause undesired

operation.

Privacy of communications may not be ensured when

using this product.

The term ‘’IC:‘’ before the certiﬁcation/registration

number only signiﬁes that the Industry Canada

technical speciﬁcations were met.

This product meets the applicable Industry Canada

technical speciﬁcations.

RF radiation exposure statement

The baby unit complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The baby unit should be installed and

operated with a minimum distance of 8 in (20 cm)

between the baby unit and all persons’ body. Use of

other accessories may not ensure compliance with

FCC RF exposure guidelines. This transmitter must

not be co-located or operating in conjunction with

any other antenna or transmitter. This equipment

complies also with Industry Canada RSS-102 with

respect to Canada’s Health Code 6 for Exposure of

Humans to RF Fields.

California Energy Commission

battery charging testing mode

This baby monitor meets the California Energy

Commission (CEC) regulations for energy

consumption. Your baby monitor is set up to comply

with the energy-conserving standards right out of

the box.

Follow the instructions to install and charge the

battery. The CEC battery charging testing mode is

activated while charging.

Even if the parent unit is paired to baby units, the

CEC battery charging testing mode is activated while

it is powered off and charging.

For cETL compliance only

Mesures de sécurité importantes

Lorsque vous utilisez votre appareil, vous devriez

toujours suivre certaines mesures de précaution

de base aﬁn de réduire les risques d’incendie,

d’électrocution et de blessures corporelles, dont

ceux qui suivent :

Observez toutes les instructions et mises en

garde inscrites sur l’appareil.

L’installation par un adulte est requise.

Ce produit a été conçu pour être un dispositif

d’appoint seulement. Il n’est pas le remplacement

d’une supervision responsable et adéquate par un

adulte et ne devrait pas être utilisé comme telle.

Ce produit n’est pas conçu pour être utilisé en

tant que moniteur médical.

N’utilisez pas cet appareil près de l’eau ni de

toute autre source d’humidité, par exemple, près

d’une baignoire, cuve à lessive, évier de cuisine,

dans un sous-sol humide ni près d’une piscine,

dans un soussol humide ou une douche.

MISE EN GARDE: Il peut y avoir un risque

d’explosion si vous utilisez le mauvais type de

piles pour l’unité du parent. N’utilisez que le

bloc-piles rechargeable inclus ou le bloc-piles de

rechange (BT198555/BT298555). N’incinérez pas

les piles. Celles-ci risqueraient d’exploser. Jetez

les piles usées selon les renseignements suivant

le sceau du RBRC®.

N’utilisez que les adaptateurs inclus avec ce

produit. L’utilisation d’un adaptateur dont la

polarité ou la tension serait inadéquate risque

d’endommager sérieusement le produit et mettre

votre sécurité en péril.

Adaptateur de l’unité du bébé :

Sortie : 5.9 V CC 1A

Adaptateur de l’unité du parent :

Sortie : 6 V CC 800mA

Pour les produits à brancher à une prise de

courant, la prise de courant doit être installée

près du produit, aﬁn d’assurer une accessibilité

sécuritaire à la prise de courant.

Lorsqu’ils sont branchés dans une prise de

courant, les adaptateurs secteur ont été conçus

pour être orientés correctement, soit à la

verticale ou au plancher. Les broches n’ont pas

été conçues pour supporter le poids du bloc

d’alimentation et le maintenir en place si celuici

est branché dans une prise au plafond, sous une

table ou dans un meuble.

Débranchez ce produit de la prise de courant

avant de procéder au nettoyage. N’utilisez pas de

nettoyants en aérosols. Utilisez un chiffon humide

pour le nettoyer.

Débranchez les cordons d’alimentation avant de

remplacer le bloc-piles.

Ne coupez pas les cordons d’alimentation pour

remplacer les ﬁches, car ceci peut présenter un

danger potentiel.

10.

11.

Ne laissez aucun objet reposer ni appuyer sur

le cordon d’alimentation. N’installez pas cet

appareil dans un endroit où l’on risque d’écraser

le cordon d’alimentation ou de le piétiner.

Ne faites fonctionner cet appareil qu’avec le

type d’alimentation indiqué sur l’étiquette. Si

vous ne connaissez pas le type d’alimentation

que vous possédez à votre domicile, consultez

votre marchand ou votre compagnie locale

d’électricité.

Ne surchargez pas les prises de courant

murales ni les rallonges électriques.

Ne placez pas cet appareil sur un chariot,

meuble, trépied, support de montage ni table

chancelants.

Les trous et ouvertures du boîtier, situés à

l’arrière de l’appareil ou sous celui-ci, servent à

aérer l’appareil. Pour l’empêcher de surchauffer,

ne bloquez sous aucun prétexte ces ouvertures

et n’empêchez pas l’aération adéquate de

l’appareil en le plaçant sur un lit, divan, tapis ou

toute autre surface similaire. De même, ne le

positionnez pas à proximité ni au-dessus d’une

source de chaleur ou d’un calorifère. De plus, ne

placez pas l’appareil dans un endroit avant de

vous assurer qu’il y ait une bonne circulation d’air.

N’enfoncez jamais d’objets à travers les

ouvertures de cet appareil, car ils pourraient

entrer en contact avec des points de tension

dangereux ou causer des courts-circuits qui

peuvent dégénérer en incendies ou en risques

d’électrocution. Ne renversez jamais de liquide

dans ce produit.

Aﬁn de réduire les risques d’électrocution, ne

démontez pas cet appareil, mais apportez-le

dans un centre de service autorisé. L’ouverture

du boîtier ou le retrait de toutes pièces que

contient cet appareil, à l’exception de l’accès

autorisé à certaines portes ou ouvertures,

risque de vous exposer à des points de tension

dangereux ou d’autres dangers. Un remontage

incorrect peut par la suite présenter des risques

d’électrocution.

Vous devriez tester la réception chaque fois que

vous mettez l’appareil en fonction.

Examinez les composantes aﬁn de vériﬁer si

celles-ci ne sont pas endommagées.

Soyez avisé de la perte de la conﬁdentialité

lorsque vous utilisez les ondes publiques. Les

conversations peuvent être entendues par

d’autres moniteurs de bébé, des téléphones

sans ﬁl, des scanneurs, etc.

Les enfants devraient être supervisés aﬁn de

vous assurer qu’ils ne jouent pas avec l’appareil.

Le produit n’est pas conçu pour être utilisé

par des personnes (incluant des enfants) aux

capacités physiques, sensorielles ou mentales

réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné

sufﬁsamment de supervision ou d’instructions

relativement à l’utilisation de l’appareil par une

personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

Mises en garde

Utilisez et entreposez le produit à une

température entre 0˚ C (32˚F) et 40˚C (104˚ F).

N’exposez pas cet appareil à des froids ou des

chaleurs extrêmes, ainsi qu’à la lumière directe

du soleil. Ne l’installez pas près d’une source de

chauffage.

Le bloc-piles ne doit pas être exposé à la

chaleur excessive telle que la lumière du soleil

ou au feu.

Assurez-vous que le moniteur et le cordon

de l’adaptateur sont toujours hors de portée

des enfants, à au moins 1 mètre (3 pieds) de

l’enfant ou du berceau, pour éviter tout risque de

strangulation.

Ne jamais placer le moniteur à l’intérieur du

berceau ou du parc de bébé. Ne jamais couvrir

le moniteur ou l’unité (s) portative avec un article

tel une serviette ou une couverture.

D’autres équipements électroniques peuvent

produire des interférences sur votre moniteur

vidéo et audio. Tentez d’installer votre

moniteur vidéo ou audio à l’écart des appareils

électroniques tels que des routeurs sans fil,

radios, téléphones cellulaires, interphones,

moniteurs, téléphones, ordinateurs personnels,

électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans

l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux

dispositifs numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC

(WTR)’, une firme de recherche indépendante,

a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans fil portatifs

et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des

aliments et drogues (FDA) des États-Unis, la firme

WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

Vous devriez maintenir les dispositifs sans fil à

au moins six pouces du simulateur cardiaque.

Ils ne doivent PAS placer le téléphone sans fil

directement sur le stimulateur cardiaque, tel que

dans une poche de chemise, lorsque celui-ci est

en marche.

L’étude effectuée par l’organisme WRS n’a pas

identifié de risque pour les détenteurs de simulateurs

cardiaques causés par les gens qui utilisent

dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes

les normes se rapportant aux champs

électromagnétiques (EMF) standard. Si vous le

manipulez correctement en suivant les instructions

de ce guide, son utilisation sera sécuritaire pendant

de nombreuses années, selon les meilleures

évidences scientifiques dont nous disposons

aujourd’hui.

•

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to

the holder of a valid proof of purchase (“Consumer”

or “you”) that the Product and all accessories

provided in the sales package (“Product”) are

free from defects in material and workmanship,

pursuant to the following terms and conditions,

when installed and used normally and in accordance

with the Product operating instructions. This limited

warranty extends only to the Consumer for Products

purchased and used in the United States of America

and Canada.

What will VTech do if the Product is not free from

defects in materials and workmanship during

the limited warranty period (“Materially Defective

Product”)?

During the limited warranty period, VTech’s

authorized service representative will repair

or replace at VTech’s option, without charge,

a Materially Defective Product. If we repair

the Product, we may use new or refurbished

replacement parts. If we choose to replace the

Product, we may replace it with a new or refurbished

Product of the same or similar design. We will

retain defective parts, modules, or equipment.

Repair or replacement of the Product, at VTech’s

option, is your exclusive remedy. VTech will return

the repaired or replacement Products to you in

working condition. You should expect the repair or

replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If

VTech repairs or replaces a Materially Defective

Product under the terms of this limited warranty,

this limited warranty also applies to the repaired

or replacement Product for a period of either (a)

90 days from the date the repaired or replacement

Product is shipped to you or (b) the time remaining

on the original one-year warranty; whichever is

longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, ﬁre, water or other

liquid intrusion; or

2. Product that has been damaged due to repair,

alteration or modiﬁcation by anyone other than an

authorized service representative of VTech; or

3. Product to the extent that the problem experienced

is caused by signal conditions, network reliability,

or cable or antenna systems; or

4. Product to the extent that the problem is caused

by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product

serial number plates or electronic serial numbers

have been removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for

repair from outside the United States of America

or Canada, or used for commercial or institutional

purposes (including but not limited to Products

used for rental purposes); or

7. Product returned without a valid proof of purchase

(see item 2 on the next page); or

8. Charges for installation or set up, adjustment of

customer controls, and installation or repair of

systems outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit

our website at www.vtechphones.com or

call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or callcall 1 (800) 267-7377.

NOTE: Before calling for service, please review the

user’s manual - a check of the Product’s controls

and features may save you a service call.

Except as provided by applicable law, you assume

the risk of loss or damage during transit and

transportation and are responsible for delivery or

handling charges incurred in the transport of the

Product(s) to the service location. VTech will return

repaired or replaced Product under this limited

warranty. Transportation, delivery or handling charges

are prepaid. VTech assumes no risk for damage or

loss of the Product in transit. If the Product failure

is not covered by this limited warra nty, or proof of

purchase does not meet the terms of this limited

warranty, VTech will notify you and will request that

you authorize the cost of repair prior to any further

repair activity. You must pay for the cost of repair and

return shipping costs for the repair of Products that

are not covered by this limited warranty.

What must you return with the Product to get

warranty service?

Return the entire original package and contents

including the Product to the VTech service

location along with a description of the malfunction

or difﬁculty; and

Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model)

and the date of purchase or receipt; and

Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech. It supersedes

all other written or oral communications related to this

Product. VTech provides no other warranties for this

Product. The warranty exclusively describes all of

VTech’s responsibilities regarding the Product. There

are no other express warranties. No one is authorized

to make modiﬁcations to this limited warranty and you

should not rely on any such modiﬁcation.

State/Provincial Law Rights: This warranty gives you

speciﬁc legal rights, and you may also have other rights,

which vary from state to state or province to province.

Limitations: Implied warranties, including those of

ﬁtness for a particular purpose and merchantability (an

unwritten warranty that the Product is ﬁt for ordinary

use) are limited to one year from the date of purchase.

Some states/provinces do not allow limitations on

how long an implied warranty lasts, so the above

limitation may not apply to you. In no event shall

VTech be liable for any indirect, special, incidental,

consequential, or similar damages (including, but

not limited to lost proﬁts or revenue, inability to use

the Product or other associated equipment, the cost

of substitute equipment, and claims by third parties)

resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of

incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Technical speciﬁcations

Frequency

control Crystal controlled PLL synthesizer

Transmit

frequency Baby unit: 2409.75 - 2473.875 MHz

Parent unit: 2409.75 -2473.875 MHz

Channels 24

LCD 2.8” Color LCD

(QVGA 320x240 pixel)

Nominal

effective

range

Maximum power allowed by FCC

and IC. Actual operating range may

vary according to environmental

conditions at the time of use.

Power

requirements Parent unit: 3.7V Li-polymer battery

Baby unit power adapter:

Output: 5.9V DC @ 1A

Parent unit power adapter:

Output: 6V DC @ 800mA

VTech Communications, Inc.

A member of THE VTECH GROUP OF COMPANIES.

VTech is the registered trademark of VTech Holdings Limited.

Speciﬁcations are subject to change without notice.

Document order number: 91-007363-070-100

Designed to ﬁt your home.

And your life.

VTech VM333 Manuel utilisateur

Marque: VTech

Modèle: VM333

Catégorie: Moniteurs vidéo bébé

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech VM333 User manual

VTech VM333 Manuel utilisateur

VTech VM333 Manuel utilisateur

dans d''autres langues

Documents connexes