PowerStroke PS171433 Le manuel du propriétaire
- Catégorie
- Nettoyeurs haute pression
- Taper
- Le manuel du propriétaire
SAVE THIS MANUAL FOR FUTURE REFERENCE
Ce nettoyeur haute pression a été conçu et fabriqué conformément
aux strictes normes de fiabilité, simplicité d’emploi et sécurité
d’utilisation. Correctement entretenu, il vous donnera des années
de fonctionnement robuste et sans problème.
AVERTISSEMENT :
Pour réduire les risques de
blessures, l’utilisateur doit lire et veiller à bien comprendre
le manuel d’utilisation avant d’utiliser ce produit.
Merci de votre achat.
Su lavadora de presión ha sido diseñada y fabricada de confor-
midad con las estrictas normas para brindar fiabilidad, facilidad
de uso y seguridad para el operador. Con el debido cuidado,
le brindará muchos años de sólido y eficiente funcionamiento.
ADVERTENCIA: Para reducir el riesgo de lesiones,
el usuario debe leer y comprender el manual del operador
antes de usar este producto.
Le agradecemos su compra.
CONSERVER CE MANUEL POUR
FUTURE RÉFÉRENCE GUARDE ESTE MANUAL PARA
FUTURAS CONSULTAS
Your pressure washer has been engineered and manufactured to our high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
1700 PSI ELECTRIC PRESSURE WASHER
NETTOYEUR PRESSION À ÉLECTRIQUE DE 1700 PSI
LAVADORA DE PRESIÓN A ELÉCTRICA DE 1700 PSI
PS171433
(ALL VERSIONS / TOUTES LES VERSIONS / TODAS LAS VERSIONES)
To register your POWERSTROKE product, please visit:
http://register.powerstroketools.com/
Pour enregistrer votre produit de POWERSTROKE, s’il vous
plaît la visite: http://register.powerstroketools.com/
Para registrar su producto de POWERSTROKE, por favor
visita: http://register.powerstroketools.com/
CUSTOMER SERVICE
SERVICE CLIENTELE
SERVICIO AL CLIENTE
USA: 1-877-617-3501
Mexico: 01 800 843 1111
www.powerstroketools.com
DO NOT USE E15 OR E85 FUEL IN THIS UNIT.
IT IS A VIOLATION OF FEDERAL LAW
AND WILL DAMAGE THE UNIT
AND VOID YOUR WARRANTY.
NE PAS UTILISER D’ESSENCE E15 OU E85 DANS CET APPAREIL. UNE
TELLE UTILISATION REPRÉSENTE UNE VIOLATION DE LA LOI FÉDÉRALE ET
ENDOMMAGERA L’APPAREIL ET ANNULERA LA GARANTIE.
NO UTILICE COMBUSTIBLES E15 O E85 EN ESTA UNIDAD.
ESTO CONSTITUYE UNA VIOLACIÓN A LA LEY FEDERAL,
DAÑARÁ LA UNIDAD Y ANULARÁ LA GARANTÍA.
ii
Fig. 1
Fig. 2
A
Fig. 3
A - Electrical cord with GFCI plug (cordon électrique avec prises
GFCI, cordón del mango con tomacorriente GFCI)
B - Spray wand (lance de pulvérisation, tubo rociador)
C - Trigger (gâchette, gatillo)
D - Lock-out button (bouton de verrouillage, botón del seguro)
E - High pressure hose (tuyau haute pression, manguera de alta
presión)
F - Water intake (prise d’eau, entrada de agua)
G - On/off switch (interrupteur marche/arrêt, interruptor de
encendido/apagado)
H - Detergent tank (réservoir de détergent, tanque de detergente)
I - Spray wand holder (zone de rangement de la lance de
pulvérisation, almacenamiento del tubo rociador)
J - High pressure hose storage reel (dévidoir pour tuyau haute
pression, carrete de almacenamiento de la manguera de alta
presión)
K - Face of power cord storage reel (couvercle du dévidoir pour
cordon d’alimentation, frente del carrete de almacenamiento del
cordón eléctrico)
L - Nozzle storage (rangement de buse, almacenamiento de
boquillas)
M
- Trigger handle (poignée de gâchete, mango del gatillo)
Fig. 4
A
F
H
E
Fig. 5
A - Trigger handle (poignée à gâchette, mango
del gatillo)
B - Spray wand (poignée à gâchette, tubo
rociador)
A
B
A - Test button (essayer le bouton, botón de
prueba)
B - Reset button (bouton « reset », botón de
reajuste)
See this fold-out section for all of the figures referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner toutes les figures mentionnées dans le manuel d’utilisation.
Consulte esta sección desplegable para ver todas las figuras a las que se hace referencia en el manual del operador.
B
A - Handle assembly (ensemble de poignée,
conjunto de mango)
B - Buttons (boutons, botóns)
G
I
J
K
A
B
B
B
C
D
LM
A - Pressure washer power cord
(cordon d’alimentation de la
laveuse à pression, cordón de
corriente de la lavadora de presión)
B - Drip loop (boucle d’égouttement,
vuelta de goteo)
C - Extension cord (cordon
prolongateurs, cordón de
extensión)
A
B
C
iii
Fig. 6
A - Hose inlet (arrivée de tuyau, entrada de
manguera)
B - High pressure hose (tuyau de haute pression,
manguera de alt a presión)
C - Hose lock (verrouillage de tuyau, bloqueo de
manguera)
A - Cap (capuchon, tapa)
B - Detergent (détergente, detergente)
C - Detergent tank (réservoir de détergente,
tanque de detergente)
BC
A
B
C
Fig. 13
A - Trigger (gâchette, gatillo)
B - Lock-out button (bouton de verrouillage,
botón de seguro)
Fig. 9
A - Spray wand (lance de pulvérisation, tubo
rociador)
B - Nozzle (buse, boquilla)
C - Turbo nozzle (buse de turbo, boquilla de
turbo)
D - Pull back the quick-connect collar (tirer la
bague à connexion rapide, tire del collar de
conexión rápida)
E - Push the nozzle into place (insérer en place la
buse, introduzca la boquilla en su lugar)
F - Push the collar forward (poussez en avant la
bague, empuje del collar adelante)
A
BC
Fig. 11
A - On/off switch (interrupteur marche/arrêt,
interruptor de encendido)
A
Fig. 10
A
B
A
Fig. 7
Fig. 12
A - Garden hose (tuyau d’arrosage, manguera de
jardín)
B - Water intake (rise d’eau, entrada de agua)
A
B
Fig. 8
A - Straightened paper clip (trombone droit, clip
para papel abierto)
B - Nozzle (embout, boquilla)
A
B
25
25
DD
E
E
FF
Fig. 14
Page / Página 2
Introduction ......................................................................................................................................................................2
Introduction / Introducción
Important Safety Instructions ........................................................................................................................................... 3
Instructions importantes concernant la sécurité / Instrucciones importantes de seguridad
Specific Safety Rules .....................................................................................................................................................4-5
Règles de sécurité particulières / Reglas de seguridad específicas
Symbols ......................................................................................................................................................................... 6-7
Symboles / Símbolos
Electrical ........................................................................................................................................................................... 8
Caractéristiques électriques / Aspectos eléctricos
Features ............................................................................................................................................................................9
Caractéristiques / Características
Assembly .....................................................................................................................................................................9-10
Assemblage / Armado
Operation ................................................................................................................................................................... 11-13
Utilisation / Funcionamiento
Maintenance ................................................................................................................................................................... 13
Entretien / Mantenimiento
Troubleshooting .............................................................................................................................................................. 14
Dépannage / Solución de problemas
Warranty ......................................................................................................................................................................... 15
Garantie / Garantía
Parts Ordering and Service ...............................................................................................................................Back Page
Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
* * *
Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la
conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à
utiliser et à entretenir.
* * *
Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto
se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.
TABLE OF CONTENTS
TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO
INTRODUCTION
INTRODUCTION / INTRODUCCIÓN
Page 3 — English
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire, and/or serious personal injury.
WARNING:
When using this product basic precautions should always
be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
THIS PRODUCT
To reduce the risk of injury, close supervision is neces-
sary when a product is used near children.
Be thoroughly familiar with controls. Know how to stop
the product and release pressure quickly.
Stay alert and exercise control. Watch what you are
doing and use common sense. Do not operate product
when you are tired. Do not rush.
Do not operate the product while under the influence
of drugs, alcohol, or any medication.
Keep the area of operation clear of all persons,
particularly small children, and pets.
Don’t overreach or stand on unstable support. Keep
proper footing and balance at all times.
Follow the maintenance instructions specified in this
manual.
This product is provided with a ground fault circuit
interrupter built into the power cord plug. If replace-
ment of the plug or cord is needed, use only identical
replacement parts.
WARNING: Risk of injection or injury – Do not direct
discharge stream at persons.
SAVE THESE INSTRUCTIONS
GROUND FAULT CIRCUIT INTERRUPTER
PROTECTION
This pressure washer is provided with a ground fault circuit
interrupter (GFCI) built into the plug of the power supply
cord. This device provides additional protection from the risk
of electric shock. Should replacement of the plug or cord
become necessary, use only identical replacement parts that
include GFCI protection.
EXTENSION CORDS
See Figure 1.
Use only extension cords that are intended for outdoor use.
These extension cords are identified by a marking “Accept-
able for use with outdoor appliances; store indoors while not
in use.” Use only extension cords having an electrical rating
not less than the rating of the product. Do not use damaged
extension cords. Examine extension cord before using and
replace if damaged. Do not abuse extension cord and do
not yank on any cord to disconnect. Keep cord away from
heat and sharp edges. Always disconnect the extension cord
from the receptacle before disconnecting the product from
the extension cord. Always plug the extension cord into a
GFCI protected outlet.
To avoid the possibility of the tool plug getting wet when
using an extension cord, arrange a “drip loop” in the cord
connecting the pressure washer to the extension cord. The
“drip loop” is that part of the cord below the level of the
connector which prevents water travelling along the cord
and coming in contact with the connection. If the plug does
get wet, DO NOT unplug the cord. Disconnect the fuse or
circuit breaker that supplies power to the tool, then unplug
and examine for presence of water in the connection.
WARNING: To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not touch plug with
wet hands.
IMPORTANT SAFETY INSTRUCTIONS
Page 4 — English
To reduce the risk of electric shock the supervi-
sory circuit must be operated before an appliance is
plugged into any receptacle on the device.
Know your product. Read the operator’s manual carefully.
Learn the machine’s applications and limitations as well
as the specific potential hazards related to this product.
To reduce the risk of injury, keep children and visitors
away. All visitors should wear safety glasses and be kept
a safe distance from work area.
Use right product. Don’t force product or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
Dress properly. Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you
into moving parts. Rubber gloves and nonskid footwear
are recommended when working outdoors. Also wear
protective hair covering to contain long hair.
Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
Exercise caution to avoid slipping or falling.
Alwaysweareyeprotectionwithsideshieldsmarked
to comply with ANSI Z87.1. Following this rule will reduce
the risk of serious personal injury.
Use only recommended accessories. The use of
improper accessories may cause risk of injury.
Check damaged parts. Before further use of the
product, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged must be properly repaired or replaced by an
authorized service center to avoid risk of personal injury.
Never leave product running unattended. Turn power
off. Don’t leave product until it comes to a complete
stop.
Keep the motor free of grass, leaves, or grease to
reduce the chance of a fire hazard.
Follow manufacturer’s recommendations for safe
loading, unloading, transport, and storage of machine.
Keep product dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use
brake fluids, gasoline, petroleum-based products, or any
solvents to clean product.
Check the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire, or string
which can be thrown or become entangled in the
machine.
Do not use product if switch does not turn it off. Have
defective switches replaced by an authorized service
center.
Avoid dangerous environment. Don’t expose to rain.
Keep work area well lit. Do not operate the pressure
washer after dark.
Do not abuse the cord. Never use the cord to carry the
product or to disconnect the plug from an outlet. Keep
cord away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for the product. Receptacles are available having
built-in GFCI protection and may be used for this measure
of safety.
To reduce the risk of electric shock, this product
may have a polarized plug (one blade is wider than
the other) and if so, will require the use of a polarized
extension cord. The plug will fit into a polarized extension
cord only one way. If the plug does not fit fully into the
extension cord, reverse the plug. If the plug still does not
fit, obtain a correct polarized extension cord. A polarized
extension cord will require the use of a polarized wall
outlet. This plug will fit into the polarized wall outlet only
one way. If the plug does not fit fully into the wall outlet,
reverse the plug. If the plug still does not fit, contact a
qualified electrician to install the proper wall outlet. Do not
change the equipment plug, extension cord receptacle,
or extension cord plug in any way.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. A wire
gauge size (A.W.G.) of at least 14 is recommended for an
extension cord 25 feet or less in length. If in doubt, use the
next heavier gauge. The smaller the gauge number, the
heavier the cord. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating.
WARNING: Use outdoor extension cords marked SW-A,
SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOWA.
These cords are rated for outdoor use and reduce the risk
of electric shock.
Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil or
grease.
Never direct a water stream toward people or pets,
or any electrical device.
Ensure the high pressure hose is properly connected
before using the product.
Before starting any cleaning operation, close doors
and windows. Clear the area to be cleaned of debris,
toys, outdoor furniture, or other objects that could create
a hazard.
SPECIFIC SAFETY RULES
Page 5 — English
ONLY use cold water.
Make sure minimum clearance of 3 feet is maintained
from combustible materials.
Connect pressure washer only to an individual branch
circuit.
Hold the handle and wand securely with both hands.
Expect the trigger handle to move when the trigger is
pulled due to reaction forces. Failure to do so could cause
loss of control and injury to yourself and others.
Save these instructions. Refer to them frequently and
use them to instruct other users. If you loan someone this
product, loan them these instructions also.
Do not use acids, alkalines, solvents, flammable
material, bleaches, or industrial grade solutions in this
product. These products can cause physical injuries to
the operator and irreversible damage to the machine.
WARNING: High pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
animals, electrical devices, or the machine itself.
Keep the motor away from flammables and other
hazardous materials.
Check bolts and nuts for looseness before each use. A
loose bolt or nut may cause serious motor problems.
Before storing, allow the motor to cool.
When servicing use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
SPECIFIC SAFETY RULES
Page 6 — English
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
NOTICE: (Without Safety Alert Symbol) Indicates important information not related to an
injury hazard, such as a situation that may result in property damage.
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
Wet Conditions Alert Do not expose to rain or use in damp locations.
Risk of Injection
To reduce the risk of injection or injury, never direct a water stream
towards people or pets or place any body part in the stream. Leak-
ing hoses and fittings are also capable of causing injection injury.
Do not hold hoses or fittings.
Kickback To reduce the risk of injury from kickback, hold the spray wand
securely with both hands when the machine is on.
Electric Shock Failure to use in dry conditions and to observe safe practices can
result in electric shock.
Chemical Burns
To reduce the risk of injury or damage, DO NOT USE ACIDS,
ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,
OR INDUSTRIAL GRADE SOLUTIONS in this product.
Page 7 — English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
Alternating Current Type of current
n
o
No Load Speed Rotational speed, at no load
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
Page 8 — English
USE ONLY THIS SIZE EXTENSION CORD WHEN USING
THIS PRODUCT:
Cord Length Wire Size (A.W.G.)
25 ft. 14
50 ft. 12
100 ft. Not Allowed
NOTE: A.W.G. = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools, or other obstructions while you are working
with a power tool. Failure to do so can result in serious
personal injury.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use the product with a
damaged cord since touching the damaged area could
cause electrical shock resulting in serious injury.
GROUND FAULT CIRCUIT INTERRUPTER
See Figure 2.
This unit is equipped with a Ground Fault Circuit Interrupter
(GFCI), which guards against the hazards of ground fault
currents. An example of ground fault current is the current
that would flow through a person who is using an appliance
with faulty insulation and, at the same time, is in contact
with an electrical ground such as a plumbing fixture, wet
floor, or earth.
GFCI plugs do not protect against short circuits, overloads,
or shocks.
NOTE: To ensure readiness for use, press the reset button
each time you connect the pressure washer to the power
supply.
The GFCI plug can be tested with the TEST and RESET
buttons.
To test:
Press the TEST button. You will hear a “click” sound and
the red LED light will go out.
To restore power, press the RESET button. The LED light
will illuminate to indicate power has been restored.
Perform this test monthly to ensure proper operation of the
GFCI.
To reduce the risk of electric shock the supervi-
sory circuit must be operated before an appliance is
plugged into any receptacle on the device.
DOUBLE INSULATION
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-
wire grounded power cord. All exposed metal parts are
isolated from the internal metal motor components with
protecting insulation. Double insulated products do not need
to be grounded.
WARNING:
The double insulated system is intended to protect the
user from shock resulting from a break in the product’s
internal insulation. Observe all normal safety precautions
to avoid electrical shock.
NOTE: Servicing of a product with double insulation requires
extreme care and knowledge of the system and should be
performed only by a qualified service technician. For service,
we suggest you return the product to your nearest authorized
service center for repair. Always use original factory replace-
ment parts when servicing.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should
be connected to a power supply that is 120 volts, AC only
(normal household current), 60 Hz. Do not operate this
product on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,
double-check the power supply.
EXTENSION CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, possibly
resulting in overheating, loss of power, and/or circuit breaker
or GFCI tripping. Use the chart to determine the minimum wire
size required in an extension cord. Only round jacketed cords
listed by Underwriter’s Laboratories (UL) should be used.
When working outdoors with a product, use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” or “W” on the cord’s jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
It is possible to tie the extension cord and power cord in a
knot to prevent them from becoming disconnected during use.
Make a knot, then connect the plug end of the power cord
into the receptacle end of the extension cord. This method
can also be used to tie two extension cords together.
ELECTRICAL
Page 9 — English
PRODUCT SPECIFICATIONS
Induction Motor ......................................................................................................................120 V, 60 Hz, 13 Amps, 3-Wire
Maximum Pounds Per Square Inch Pressure* ..........................................................................................................1700 psi
Maximum Gallons Per Minute* ...................................................................................................................................1.4 gpm
Maximum Inlet Water Temperature ................................................................................................................................104˚F
*Max. rating determined by PWMA Standard 101
KNOW YOUR PRESSURE WASHER
See Figure 3.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
DETERGENT TANK
Remove the cap from the detergent tank to add detergent
to the pressure washer.
GFCI PLUG
The pressure washer is equipped with a GFCI plug to guard
against the hazards of ground fault currents. This plug does
not protect against short circuits, overloads, or shocks.
HIGH PRESSURE HOSE STORAGE REEL
A convenient hose reel stores the high pressure hose when
the pressure washer is not in use.
ON/OFF SWITCH
This switch turns the pressure washer ON and OFF.
POWER CORD STORAGE REEL
Store the power cord on the convenient storage reel when the
pressure washer is not in use. Rotate the reel face counter-
clockwise and remove for quick release of the cord.
TELESCOPING HANDLE
The telescoping handle allows the handle to be lowered for
convenient storage.
TRIGGER HANDLE
The trigger handle has a gripping surface that provides added
control of the spray wand and helps reduce fatigue.
TRIGGER WITH LOCK-OUT
Pulling the trigger releases a stream of water for high
pressure cleaning. The lock-out provides protection against
unauthorized use.
FEATURES
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
WARNING:
Do not use this product if any parts on the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-877-617-3501 for assistance.
ASSEMBLY
PACKING LIST
Pressure Washer with 25 ft. High Pressure Hose
Trigger Handle
Spray Wand
Nozzles (25°, Soap, Turbo)
Operator’s Manual
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
Page 10 — English
WARNING:
Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not connect to power supply until assembly is com-
plete. Failure to comply could result in accidental starting
and possible serious personal injury.
ATTACHING THE HANDLE ASSEMBLY
See Figure 4.
Orient the handle assembly as shown.
Depress the buttons on the handle assembly and insert
into the holes on the pressure washer. Press down on the
handle assembly until the buttons on the handle clicks
into place.
To lower the handle, depress the buttons again and lower
the handle completely.
INSTALLING THE SPRAY WAND
See Figure 5.
Push the end of the spray wand into the trigger handle
and rotate clockwise to secure.
Place the assembled spray wand in the spray wand holder.
Pull on the spray wand to be certain it is properly secured.
CONNECTING HIGH PRESSURE HOSE TO
TRIGGER HANDLE
See Figure 6.
Slide the hose lock forward to open.
Insert the high pressure hose into the trigger handle.
NOTE: See Using The High Pressure Hose in Operation
for more information about using the high pressure hose.
Slide the hose lock backward to secure the hose in place.
Pull on the hose to be certain it is properly secured.
ASSEMBLY
CONNECTING THE GARDEN HOSE
See Figure 7.
NOTICE:
Always observe all local regulations when connecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water
supply to prevent the feedback of chemicals into
the drinking water supply. Direct connection through
a receiver tank or backflow preventer is usually
permitted.
The water supply must come from a water main. NEVER
use hot water or water from pools, lakes, etc. Before
connecting the garden hose to the pressure washer:
Run water through the hose for 30 seconds to clean any
debris from the hose.
Inspect the screen in the water intake.
If the screen is damaged, do not use the machine until
the screen has been replaced.
If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
Completely uncoil the garden hose or remove completely
from reel to prevent kinks.
NOTE: There must be a minimum of 10 feet of unre-
stricted hose between the pressure washer intake and
the hose faucet or shut off valve (such as a “Y” shut off
connector).
With the hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by
hand.
NOTICE:
Do not run the pressure washer pump without water sup-
ply connected and turned on, as this may damage the
high pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Page 11 — English
WARNING:
Do not allow familiarity with the product to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
WARNING:
Never direct a water stream toward people or pets, or
any electrical device. Failure to heed this warning could
result in serious injury.
APPLICATIONS
You may use this tool around the house for cleaning most
small to large horizontal or vertical exterior surfaces, smaller
exterior objects and structures, and outdoor equipment and
tools.* You can:
Clean or remove mold and mildew from weathered decks,
driveways, patios, walkways, sidewalks, etc.
Remove dirt from various exterior vertical surfaces such
as house exteriors, siding, fences, brick, concrete or stone
walls, etc.
Wash boats, outdoor furniture, powered or non-powered
garden equipment, gutters, window screens, grills, play-
ground equipment, etc.
*Always test in an inconspicuous area first.
ADDING DETERGENT TO THE PRESSURE
WASHER
See Figure 8.
Use only detergents designed for pressure washers; house-
hold detergents, acids, alkalines, bleaches, solvents, flam-
mable material, or industrial grade solutions can damage
the pump. Many detergents may require mixing prior to use.
Prepare cleaning solution as instructed on the solution bottle.
Always test in an inconspicuous area before beginning.
Disconnect pressure washer from power supply.
Place pressure washer upright on a flat surface.
Remove cap from detergent tank.
OPERATION
Pour detergent into tank.
NOTE: Use a funnel, if needed, to prevent accidental
spilling of the detergent outside the tank. If any detergent
is spilled during the filling process, make sure the unit is
cleaned and dried before proceeding.
Reinstall cap.
PUMP LUBRICANT
The pressure washer pump has been filled with sufficient
lubricant at the factory and is maintenance free. You do not
need to check or add lubricant to the pump before initial use.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figure 9.
NOTICE:
Do not run the pressure washer pump without water sup-
ply connected and turned on, as this may damage the
high pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Connect the garden hose.
Turn the garden hose on then squeeze the trigger to
relieve air pressure. Once a steady stream of water ap-
pears, release the trigger.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
After ensuring the On/Off switch is in the OFF ( O ) posi-
tion, connect the pressure washer to the power supply.
NOTE: If using an extension cord, make sure to arrange
a drip loop as described on page 3.
Press the reset button on the pressure washer’s plug to
make sure the unit is ready for operation.
Press ON ( I ) on the switch to start the motor.
To stop the motor, release the trigger and press OFF
( O ) on the switch.
NOTE: The pressure washer may be on and the sytem
may have pressure even when the pump and/or motor
cannot be heard running. Always use caution around the
pressure washer.
WARNING:
While operating and storing, keep at least 3 feet of clear-
ance on all sides of this product, including overhead.
Allow a minimum of 30 minutes of “cool down” time
before storage. Heat created by muffler and exhaust
gases could be hot enough to cause serious burns and/
or ignite combustible objects.
Page 12 — English
OPERATION
USING THE TRIGGER AND LOCK-OUT
See Figure 10.
For greater control and safety, keep both hands on the
trigger handle at all times.
Pull back and hold the trigger to operate the pressure
washer.
Release the trigger to stop the flow of water through the
nozzle.
To engage the lock-out:
Slide the lock-out button to the left side of the trigger
handle to engage the lock-out.
To disengage the lock-out:
Slide the lock-out button to the right side of the trigger
handle to disengage the lock-out.
To use the spray wand, start with the nozzle 1-2 ft. away
from the cleaning surface. Carefully approach the surface
just until the desired level of cleaning is achieved. If the spray
is too close it can damage the cleaning surface.
SELECTING THE RIGHT NOZZLE FOR THE
JOB
See Figure 11.
Each of the nozzles has a different spray pattern. Before
starting any cleaning job, determine the best nozzle for the
job. Refer to the Nozzle Selection Guide for more informa-
tion about which nozzle to choose.
WARNING:
NEVER change nozzles without engaging the lock-out
on the trigger handle and NEVER point the wand at your
face or at others. The quick-connect feature contains
small springs that could eject the nozzle with some force.
Failure to heed this may cause personal injury.
To connect a nozzle to the trigger handle:
Turn off the pressure washer and shut off the water sup-
ply. Pull trigger to release water pressure.
Engage the lock-out on the trigger handle by pushing the
trigger lock button to the left.
Pull back the quick-connect collar.
Push the nozzle into place in the spray wand.
Push the collar forward so that the nozzle is secured
properly. Check to see that the nozzle is secure.
NOZZLE SELECTION GUIDE
HIGH PRESSURE
(NO SOAP WHEN USING THESE NOZZLES)
LOW PRESSURE
(FOR SOAP OR
GENTLE RINSE)
Turbo Nozzle 25º Blue or Black
Soap Nozzle
Concrete, Brick, Masonry
Siding, Gutters, House
Fencing, Deck, Patio
Lawn Equipment, Boat, RV
Recommended Nozzle Use With Caution for Certain Applications
Page 13 — English
To disconnect a nozzle from the trigger handle once
the cleaning job is complete:
Turn off the pressure washer and shut off the water sup-
ply. Pull trigger to release water pressure.
Engage the lock-out on the trigger handle by pushing the
trigger lock button to the right.
Remove the nozzle by placing hand over nozzle then
pulling back the quick-connect collar. Place nozzle in the
nozzle storage area on the trigger handle.
USING THE HIGH PRESSURE HOSE
The high pressure hose features an outer covering that pro-
vides strength to the hose. If the outer covering becomes
damaged, the hose must be replaced immediately. Do not
use a high pressure hose if the outer covering is damaged.
To prevent damage to the outer covering:
Inspect the hose before every use.
Fully unwrap and straighten hose before use.
Do not allow the high pressure hose to be kinked.
Keep hose away from hot surfaces and sharp edges.
Do not pull unit by high pressure hose.
Do not allow hose to be crushed or wrapped around
objects.
OPERATION
OPERATING THE PRESSURE WASHER
See Figure 12.
Use only detergents designed for pressure washers. Many
detergents may require mixing prior to use. Prepare cleaning
solution as instructed on the solution bottle.
To clean:
Pour detergent in the detergent tank.
Install the blue or black soap nozzle on the spray wand.
Start the pressure washer and spray the detergent on
a dry surface using long, even, overlapping strokes. To
prevent streaking, do not allow detergent to dry on the
surface.
To rinse:
Using the 25˚ nozzle, spray away from the rinsing surface
for approximately 10 seconds to allow any remaining
detergent to be flushed from the line.
Start at the top of the area to be rinsed and work down,
overlapping the strokes.
MOVING THE PRESSURE WASHER
Turn the pressure washer off. Point nozzle in a safe direc-
tion and pull trigger to release water pressure.
Raise the handle up until the buttons click into the holes
on the handle.
Tilt the machine toward you until it balances on the wheels
then roll the machine to the desired position.
DO NOT attempt to move the unit by pulling on any of
the hoses.
Page 14 — English
MAINTENANCE
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts could create a hazard or cause
product damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
Before inspecting, cleaning or servicing the machine, shut
off motor, wait for all moving parts to stop, disconnect
unit from power supply, and pull trigger to release water
pressure. Failure to follow these instructions can result
in serious personal injury or property damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which could result in serious personal
injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at an authorized service center.
NOZZLE MAINTENANCE
See Figure 13.
Excessive pump pressure (a pulsing sensation felt while
squeezing the trigger) may be the result of a clogged or
dirty nozzle.
Unplug the pressure washer.
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Remove the nozzle from the spray wand.
NOTE: Never point the spray wand at your face.
Using a straightened paper clip or nozzle cleaning tool
(not provided), free any foreign materials clogging or
restricting the nozzle.
Using a garden hose, flush debris out of nozzle by back
flushing (running the water through the nozzle backwards
or from the outside to the inside).
Reconnect the nozzle to the spray wand.
Turn on the water supply.
STORING THE PRESSURE WASHER
See Figure 14.
NOTE: Regular use of pump protector will give you
better performance of the unit and increase the life of
the pump. See the Replacement Parts List for available
sizes and part numbers and call customer service at
1-877-617-3501 to order.
Allow 30 minutes of “cool down” time before storing the
machine. Store in a dry, covered area where the weather
can’t damage it.
It is important to store this product in a frost-free area. Always
empty water from all hoses, the pump, and the detergent
bucket before storing.
Make sure the on/off switch is in the OFF position.
Disconnect the water connection.
Tilt the unit as shown to allow any remaining water in the
pump to drain from the water inlet.
NOTICE:
The use of a pump protector is strongly encouraged to
prevent cold weather damage during storage over the
winter months.
Remove all hoses. Coil the hoses and store as shown.
Do not allow the hose to become kinked.
Store the unit and accessories in an area that does not
reach freezing temperatures. Do not store near furnace or
other sources of heat that could dry out the pump seals.
Page 15 — English
PROBLEM POSSIBLE CAUSE SOLUTION
Pressure washer does not start
when trigger is depressed
Power cord not connected to power
source
Switch is off
GFCI is tripped
House/shop circuit breaker is tripped
Water pressure in hose
Connect the power cord to a live
120V AC, 60 Hz AC receptacle.
Turn switch on.
Press reset button on the GFCI
plug.
Reset house/shop breaker. Make
sure pressure washer is connected
to an individual branch circuit only. If
using an extension cord, make sure it
is heavy enough to carry the current
of the pressure washer.
Squeeze trigger to relieve water
pressure.
Pump doesn’t produce pressure Inadequate water supply
Spray wand leaks
Nozzle is clogged
Pump is faulty
Air in line
Water inlet filter is clogged or dirty
Provide adequate water flow.
Check connections and / or replace
wand.
Clean nozzle.
Contact authorized service center.
Squeeze trigger on spray wand to
remove air from line.
Remove the water inlet filter, rinse
with warm water, then replace in
unit.
Machine doesn’t reach high
pressure
Diameter of garden hose is too small
Water supply is restricted
Not enough inlet water
Hose is leaking
Kink in hose
Replace with 3/4 in. garden hose.
Check garden hose for kinks, leaks,
and blockages.
Open water source full force.
Replace hose.
Eliminate kinks in hose.
No detergent Detergent tank is empty
Water supply is inadequate or
clogged
Wrong nozzle is attached
Add additional detergent to tank.
Check garden hose for kinks, leaks
and blockages.
Attach blue or black soap nozzle.
Wand leaks O-ring needs replacing Replace o-ring. If this does not
correct the problem, contact your
authorized service center to purchase
a new wand.
TROUBLESHOOTING
Page 16 — English
WARRANTY
LIMITED WARRANTY
WARRANTY COVERAGE
OWT Industries, Inc., (the Company) warrants to the original retail purchaser that this PowerStroke Product is free from
defects in material and workmanship and agrees to repair or replace, at the Company’s sole discretion, any defective
Product free of charge within these time periods from the date of purchase:
Two years, if the Product is used solely for personal, family, or household use;
90 days, if the Product is used for business or commercial use.
This warranty applies only to Products sold within the United States of America, the District of Columbia, Canada,
Mexico, the Commonwealth of Puerto Rico, the Virgin Islands, Guam, the Canal Zone, or American Samoa.
This warranty is not transferable and does not cover damage resulting from defects other than in material or workman-
ship, or damage caused by unreasonable use, including the failure to provide reasonable and necessary maintenance.
Other items not covered under this warranty include:
Transportation charges for sending the product to the Company or its authorized service representative for warranty
service, or for shipping repaired or replacement products back to the customer; these charges must be borne by
the original retail purchaser.
Damages caused by abuse, accident, misuse, neglect, alteration, modification, the effects of corrosion, erosion,
normal wear and tear or repairs by other than the Company or its authorized service representative.
Warranty is voided if the customer fails to install, maintain and operate the product in accordance with the instruc-
tions and recommendations of the Company as set forth in the Product’s operator’s manual or if the Product is used
as rental equipment.
The Company will not pay for repairs or adjustments to the Product, or for any costs or labor, performed without the
Company’s prior authorization.
SAVE YOUR SALES SLIP
Proof of purchase in the form of your dated sales receipt, cash register slip, etc. showing the serial number and the
model of your Product will be required before the Company and/or its authorized service representatives can perform
warranty service on the Product.
EXCLUSIONS AND LIMITATIONS
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ANY IMPLIED WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, APPLICABLE TO THIS PRODUCT,
SHALL BE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY. THE WARRANTY SERVICE
DESCRIBED ABOVE IS THE EXCLUSIVE REMEDY UNDER THIS WARRANTY. THE COMPANY SHALL NOT BE LIABILE
FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
SOME STATES DO NOT ALLOW A LIMITATION ON THE DURATION OF IMPLIED WARRANTIES, OR THE EXCLUSION
OR LIMITATION OF INCIDENTAL, OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU.
HOW TO OBTAIN WARRANTY SERVICE
For warranty service: Call toll free 1-877-617-3501, or write to OWT Industries, Inc., P.O. Box 35, Hwy. 8, Pickens,
SC 29671.
For warranty service outside the USA, please contact your local PowerStroke dealer.
Page 17 — English
NOTES
Page 3 — Français
INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ
AVERTISSEMENT :
Lire attentivement toutes les instructions. Le non-
respect de toutes les instructions ci-dessous peut
entraîner un choc électrique, un incendie et/ou des bles-
sures graves.
AVERTISSEMENT :
Lors de l’utilisation de ce produit, toujours suivre les
consignes de base, notamment :
LIRE TOUTES LES INSTRUCTIONS AVANT
D’UTILISER CE PRODUIT
Pour réduire les risques de blessures, porter une
attention particulière lorsque le produit est utilisé en
présence d’enfants.
Se familiariser complètement avec les commandes.
Veiller à savoir arrêter la machine et relâcher la pression
rapidement.
Rester vigilant et garder le contrôle. Se montrer attentif
et faire preuve de bon sens. Ne pas utiliser le produit en
état de fatigue. Ne pas se presser.
Ne pas utiliser ce produit sous l’influence de l’alcool,
de drogues ou de médicaments.
Ne laisser personne approcher la zone de travail,
particulièrement les petits enfants et les animaux domes-
tiques.
Ne pas travailler hors de portée ou se tenir sur une
surface instable. Toujours se tenir bien campé et en
équilibre.
Suivre les instructions d’entretien décrites dans le
présent manuel.
Ce produit est fourni avec un disjoncteur de fuite à la
terre intégré dans la fiche du cordon d’alimentation.
S’il est nécessaire de procéder au remplacement de la
fiche ou du cordon, utiliser exclusivement des pièces
identiques à celles d’origine.
AVERTISSEMENT : Risque d’injection ou de blessures
– ne pas diriger le jet directement vers quelqu’un.
CONSERVER CES INSTRUCTIONS
PROTECTION D’UN DISJONCTEUR DE FUITE
À LA TERRE
Cette laveuse à pression est fournie avec un disjoncteur de
fuite à la terre intégré dans la fiche du cordon d’alimentation.
Ce dispositif offre une protection supplémentaire contre
les décharges électriques. S’il est nécessaire de procéder
au remplacement de la fiche ou du cordon, utiliser
exclusivement des pièces identiques à celles d’origine qui
incluent un disjoncteur de fuite à la terre.
CORDONS PROLONGATEURS
Voir la figure 1.
Utiliser uniquement des cordons prolongateurs conçus
pour l’extérieur. Ces cordons prolongateurs sont
étiquetés « Compatibles avec les appareils extérieurs;
entreposer à l’intérieur lorsque le produit n’est pas utilisé ».
Utiliser uniquement des cordons prolongateurs dont
les caractéristiques électriques ne sont pas inférieures
à la puissance du produit. Ne pas utiliser des cordons
prolongateurs endommagés. Examiner le cordon prolongateur
avant de l’utiliser et le remplacer s’il est endommagé. Ne pas
malmener les cordons prolongateurs ni tirer d’un coup sec
dessus pour les débrancher. Garder le cordon à l’écart de
la chaleur et des rebords tranchants. Toujours débrancher
le cordon prolongateur de la prise de courant avant de
débrancher le produit du cordon prolongateur. Toujours
brancher le cordon prolongateur dans une prise protégée
par un disjoncteur de fuite de terre.
Pour éviter que la fiche de l’outil ne se mouille au moment
d’utiliser un cordon prolongateur, installer une « boucle
d’égouttement » sur le cordon qui relie la laveuse à pression
au cordon prolongateur. La « boucle d’égouttement » est la
partie du cordon située sous le connecteur qui empêche
l’eau de suivre le cordon et d’entrer en contact avec la
prise. Si la fiche est mouillée, NE PAS débrancher le cordon.
Débrancher le fusible ou le disjoncteur qui alimente l’outil,
puis débrancher ce dernier en vérifiant si de l’eau s’est
infiltrée dans la prise.
AVERTISSEMENT : Pour réduire le risque d’électrocution,
garder toutes les connexions au sec et au-dessus du sol.
Ne pas manipuler la fiche avec les mains mouillées.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
PowerStroke PS171433 Le manuel du propriétaire
- Catégorie
- Nettoyeurs haute pression
- Taper
- Le manuel du propriétaire
dans d''autres langues
Documents connexes
Autres documents
-
Homelite ut80720 Manuel utilisateur
-
Ryobi RY1418MT Le manuel du propriétaire
-
-
-
-
-
-
Ryobi ZRRY141900NB Manuel utilisateur