Yes NV51CB700D12 Guide d'installation

Marque: Yes

Modèle: NV51CB700D12

Catégorie: Fours

Taper: Guide d'installation

Ce manuel convient également à

Built-In Electric Wall Oven

Installation manual

NV51**700**AA / NV51**600**AA

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 1DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 1 2023-04-07 오후 1:41:172023-04-07 오후 1:41:17

2 English

Contents

ContentsContents

Safety informations 2

Related equipment safety 2

Transport 2

Preparation 4

Checklist 4

Prepare to install the oven 4

Location requirements 5

Product dimensions - single ovens (NV51**700S, NV51**600S) 5

Cabinet dimensions - single ovens 6

Product dimensions - double ovens (NV51**700D, NV51**600D) 7

Cabinet dimensions - double ovens 7

Installation instructions 9

Prepare built-in oven 9

Remove and replace oven door(s) 10

Electrical connection 12

Install oven 14

Self-diagnosis 15

Temp sensor & Heater check 15

Safety informations

Related equipment safety

Remove all tape and packaging before using the appliance. Dispose of the

packaging after unpacking the appliance. Never allow children to play with

packaging material.

Never modify or alter the construction of the appliance. For example, do not

remove panels, wire covers or screws.

Transport

To avoid damage to the oven vent, use the transport method shown in the picture

below.

A. Front

B. Pallet

Support the bottom of the oven from either

side when moving it into the installation

location. Leave the unit attached to the

shipping pallet until it is in front of the

cabinet opening and is ready to be lifted

into place.

DANGER

ELECTRICAL SHOCK HAZARD

To avoid risk of electrical shock, personal injury or death; verify your appliance

has been properly grounded in accordance with local codes or in absence of codes,

with the National Electrical Code (NEC). ANSI/NFPA 70-latest edition.

WARNING

MOVING HAZARD

To avoid risk of severe personal injury; this appliance requires two or more people

while handling and moving. Use of appliance moving devices is recommended.

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 2DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 2 2023-04-07 오후 1:41:172023-04-07 오후 1:41:17

English 3

Safety informations

WARNING

• The information in this manual should be followed exactly.

-A re or electrical shock may result causing property damage, personal

injury or death.

• Important - Save this installation manual for local electrical inspector's use.

• Proper Installation - Be sure your appliance is properly installed and grounded

by a qualied technician.

• New branch-circuit installations (1996 NEC), mobile homes, recreational

vehicles, or installations where local codes prohibit grounding through the

neutral conductor require 4-wire branch-circuit connection.

• Improper connection of aluminum house wiring to copper leads can result in

an electrical hazard or re. Use only connectors designed for joining copper to

aluminum and follow the manufacturer’s recommended procedure closely.

• Mounting screws must be used.

-Failure to do so can result in the oven falling out of the cabinet causing

serious injury.

CAUTION

• Make sure the cabinets and wall coverings around the oven can withstand the

temperature (up to 194 °F [90 °C]) generated by the oven.

-Discoloration, delamination or melting may occur.

• DO NOT remove spacers on the side walls of the built-in oven.

-These spacers center the oven in the space provided. The oven must be

centered to prevent excess heat buildup that may result in heat damage

or re.

WARNING

• The information in this manual should be followed exactly.

-A re or electrical shock may result causing property damage, personal

injury or death.

IMPORTANT NOTE

Proper installation is the responsibility of the installer and product failure due to

improper installation is NOT covered under warranty.

WARNING

• DO NOT put any weight on the oven door. Never allow anyone to climb, sit,

stand or hang on the oven door.

-The oven could tip and injury might result from food or the oven itself.

WARNING

• The electrical power must be shut off while the electrical connections are

being made.

-Failure to do so can result in severe personal injury, death or electrical

shock.

IMPORTANT NOTE

• Observe all governing codes and ordinances. This appliance must be properly

grounded.

• Keep oven vent ducts unobstructed. The oven vent is located bottom of the

oven. This area could become hot during oven use. Never block this vent or

place plastic or heat-sensitive items in front of it.

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 3DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 3 2023-04-07 오후 1:41:172023-04-07 오후 1:41:17

4 English

Preparation

Checklist

Use this checklist to verify that you have completed each step of the installation

process. This can help you avoid mistakes.

1. Before installing the oven, be sure to verify the cabinet dimensions are correct

for your unit and the required electrical connections are present.

2. Refer to the installation manual for content regarding Safety, Cabinet

Dimensions, Removing Packaging, Electrical Installation, Testing the

Installation and Customer Service.

3. To lift up the oven, hang the install handle onto the side hook of the unit.

4. Move the oven unit into place in front of the cabinet opening, leaving the

bottom packaging on the unit to avoid damaging ooring.

5. Team lift the unit directly into the cabinet cutout taking care not to pinch

ngers or scratch hands or arms. Make sure the electrical conduit reaches to

the connection point properly.

6. Slide the unit all the way into place, making sure to route the electrical conduit

correctly.

7. Fasten the oven unit to the cabinetry opening with screws supplied (using

Phillips screwdriver).

8. Consult the complete installation instructions and follow the remainder of the

procedures listed, including performing an operation test.

9. All product literature and accessories are supplied (may be wrapped or boxed)

with the oven.

10. INSTALLER - Leave the literature pack and the accessories with the customer.

11. Hang the install handle onto the side hook of the oven.

Prepare to install the oven

Phillips Screwdriver Drill

Prepare to install the oven

6 screws (M4 L16)

6 Wood Screws For

Mounting (4 needed for

installation and 2 extra’s)

30” (76.2 cm)

Metal Bottom Trim

Install Handle

(only for double oven)

Materials needed

Junction Box Wire Nuts 3/4” Conduit Connector

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 4DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 4 2023-04-07 오후 1:41:172023-04-07 오후 1:41:17

English 5

Preparation

Location requirements

IMPORTANT: Observe all governing codes and ordinances.

• Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance with oven.

• Recessed installation area must provide complete enclosure around the

recessed portion of the oven.

• Grounded electrical supply is required. See “Electrical Requirements” section.

• Electrical supply junction box should be located 3” (7.6 cm) maximum below

the support surface when the oven is installed in a wall cabinet. A 1” (2.5 cm)

minimum diameter hole should have been drilled in the right rear or left

rear corner of the support surface to pass the appliance cable through to the

junction box.

NOTE

For under counter installation, it is recommended that the junction box be located

in the adjacent right or left cabinet. If you are installing the junction box on rear

wall behind oven, it is recommended that the junction box be recessed and located

in the upper Right of the cabinet.

• Oven support surface must be solid, level and ush with bottom of cabinet

cutout.

• Floor must be able to support a single oven weight of at least 199 lb (90 Kg).

• Floor must be able to support a double oven weight of at least 331 lb (150 Kg).

IMPORTANT: To avoid damage to your cabinets, check with your builder or

cabinet supplier to make sure that the materials used will not discolor, delaminate

or sustain other damage. This oven has been designed in accordance with the

requirements of UL and CSA International and complies with the maximum

allowable wood cabinet temperatures of 194 °F (90 °C).

Product dimensions - single ovens (NV51**700S, NV51**600S)

※ Oven Vent

Blocking the vent may cause

premature oven failure.

AG

D-2

D

D-1

H

DIMENSION

A2813/16” (73.1 cm) Overall height

B281/2” (72.4 cm) Recessed width

C273/16” (69.1 cm) Recessed height

D1265/8” (67.6 cm) Overall depth (with Handle)

D-1 231/8” (58.7 cm) Recessed depth

D-2 243/8” (62.0 cm) Overall depth

E293/4” (75.6 cm) Door width

F471/4” (120 cm) Conduit length

G12715/16” (70.9 cm) Overall width (Handle width)

H121/4” (5.6 cm) Handle depth

¹NV51**600S

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 5DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 5 2023-04-07 오후 1:41:172023-04-07 오후 1:41:17

6 English

Preparation

Cabinet dimensions - single ovens

Single Oven Under counter

01 Gas or Electric cooktops may be installed over this oven. See cooktop

installation instructions for cutout size. See label on top of approved

cooktop models.

02 Gas and Electrical Connections for Gas Cooktop Must be Located in an

Adjacent Accessible Location to the Right.

DIMENSION

AMin. 11/16” (1.75 cm) – Overlap of Over Side Edges of Cutout

BMin. 41/8” (10.5 cm)

C35/8” (9.1 cm)

DMin. 281/2”/ Max. 285/8” (Min. 72.4 cm / Max. 72.7 cm)

EMin. 1”/ Max. 11/4” (Min. 2.5 cm / Max. 3.2 cm)

FMin. 271/4”/ Max. 273/8” (Min. 69.2 cm / Max. 69.5 cm)

GMin. 231/2” (Min. 59.7 cm)

HMin 22” (Min 55.9 cm)

IMax. 91/2” (Max. 24.1 cm) – Junction Box

J363/8” (92.3 cm) - Counter top Height

K25” (63.5 cm)

Single Oven Wall Mount

01 Junction Box

02 Allow a minimum of 22” for clearance to adjacent corners, drawers, walls,

etc. when door is open

22”

DIMENSION

A30” (76.2 cm)

BMin. 13/8” (3.5 cm)

CMin. 31” (Min 78.7 cm)

DMin. 281/2”/ Max. 285/8” (Min. 72.4 cm / Max. 72.7 cm)

EMin. 1”/ Max. 11/4” (Min. 2.5 cm / Max. 3.2 cm)

FMin. 271/4”/ Max. 273/8” (Min. 69.2 / Max. 69.5 cm)

GMin. 231/2” (Min. 59.7 cm)

HMin. 22” (Min. 55.9 cm)

IMax. 91/2” (Max. 24.1 cm) – Junction Box

JMin. 11/16" (1.75 cm) - Wooden cabinet thickness

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 6DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 6 2023-04-07 오후 1:41:182023-04-07 오후 1:41:18

English 7

Preparation

Product dimensions - double ovens (NV51**700D, NV51**600D)

H

D-1

D-2

D

G

※ Oven Vent

Blocking the vent may cause

premature oven failure.

DIMENSION

A511/2” (130.7 cm) Overall height

B281/2” (72.4 cm) Recessed width

C497/8” (126.7 cm) Recessed height

D1265/8” (67.6 cm) Overall depth (with Handle)

D-1 231/8” (58.7 cm) Recessed depth

D-2 243/8” (62.0 cm) Overall depth

E293/4” (75.6 cm) Door width

F67” (170 cm) Conduit length

G12715/16” (70.9 cm) Overall width (Handle width)

H121/4” (5.6 cm) Handle depth

¹NV51**600D

Cabinet dimensions - double ovens

Double Ovens Installed in Cabinet

01 Junction Box

02 Allow a minimum of 22” for clearance to adjacent corners, drawers, walls,

etc. when door is open

22”

DIMENSION

A30” (76.2 cm)

BMin. 13/16” (3.0 cm)

C12” (30.5 cm)

DMin. 281/2”/ Max. 285/8” (Min. 72.4 cm / Max. 72.7 cm)

EMin. 1”/ Max. 11/4” (Min. 2.5 cm / Max. 3.2 cm)

F501/4” (127.6 cm)

GMin. 231/2” (Min. 59.7 cm)

HMin 47” (Min. 119.4 cm)

IMax. 91/2” (Max. 24.1 cm) – Junction Box

JMin. 11/16" (1.75 cm) - Wooden cabinet thickness

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 7DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 7 2023-04-07 오후 1:41:182023-04-07 오후 1:41:18

8 English

Preparation

Electrical Connection

To properly install your oven, you must determine the type of electrical connection

you will be using and follow the instructions provided in this manual.

• Oven must be connected to the proper electrical voltage and frequency as

specied on the model/serial/rating plate. The model/serial/rating plate is

located on the bottom left side of the trim. See the following illustrations.

Single Oven

A. Model/serial/rating plate

Double Oven

A. Model/serial/rating plate

• A circuit breaker is recommended.

• Use the chart below to determine the minimum recommended dedicated

circuit protection.

KW Rating (240 V) KW Rating (208 V) Recommended Circuit

Size (Dedicated)

≤4.8 KW ≤4.1 KW 20 Amp

4.9 KW - 7.5 KW 4.3 KW - 6.2 KW 30 Amp

7.3 KW - 9.6 KW 6.3 KW - 8.3 KW 40 Amp

9.7 KW - 12.0 KW 8.4 KW - 10.4 KW 50 Amp

• Connect directly to the circuit breaker box (or fused disconnect) through

exible, armored or nonmetallic sheathed, copper cable (with grounding wire).

See “Electrical Connection” section.

If codes permit and a separate ground wire is used, it is recommended that a

qualied electrical installer determine that the ground path and the wire gauge are

in accordance with local codes.

Check with a qualied electrical installer if you are not sure the oven is properly

grounded.

This oven must be connected to a grounded-metal permanent wiring system.

Be sure that the electrical connection and wire size are adequate and in

conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA

Standards C22.

1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all

local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 8DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 8 2023-04-07 오후 1:41:182023-04-07 오후 1:41:18

English 9

Installation instructions

• Flexible conduit from the oven should be connected directly to the junction

box.

• Fuse both sides of the line.

• Do not cut the conduit. The length of conduit provided is for serviceability of

the oven.

• A UL listed or CSA approved conduit connector must be provided.

• If the house has aluminum wiring, follow the procedure below:

1. Connect a section of solid copper wire to the ends of the exible conduit

leads.

2. Connect the aluminum wiring to the added section of copper wire using

special connectors and/or tools designed and UL listed for joining copper

to aluminum.

Follow the electrical connector manufacturer's recommended procedure.

Aluminum/copper connection must conform with local codes and industry accepted

wiring practices.

For power requirements for models NV51**700D, NV51**600D, NV51**700S,

NV51**600S, refer to the following table.

Model 240 VAC 208 VAC

kW kW

NV51**600D 9.3 7.0

NV51**600S 4.9 3.7

NV51**700D 10.6 8.0

NV51**700S 6.2 4.7

Installation instructions

Prepare built-in oven

WARNING

Excessive Weight Hazard

Use two or more people to move and install an oven.

Failure to do so can result in back or other injury.

1. Decide on the nal location for the oven. Avoid drilling or cutting into house

wiring during installation.

2. To avoid oor damage, set the oven on a cardboard prior to installation. Do

not use handle or any portion of the front frame for lifting.

3. Remove the shipping materials and tape from the oven.

Remember to keep the packing materials that may be needed for installation.

4. Remove the hardware package from inside of the bag containing literature.

5. Remove racks and other parts from inside the oven.

6. Move oven and cardboard close to the oven’s nal location.

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 9DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 9 2023-04-07 오후 1:41:182023-04-07 오후 1:41:18

10 English

Installation instructions

Remove and replace oven door(s)

IMPORTANT: Use two hands to remove oven door. For double ovens, repeat the

process for each door.

Prior to removing the oven door, prepare a surface where you will place it. This

surface should be at and covered with a soft blanket, or use the corner posts

from your packaging material.

Disconnect LED light wire harness (Only NV51**700*****)

Locate the LED light wire harness and disconnect it before removing the door.

Single Oven

Wire Harness

Double Oven

1. Carefully pull the wire to reveal the

connector.

2. Disconnect the connector.

Remove oven door(s)

A. Oven door hinge lock in

locked position

B. Oven door hinge lock in

unlocked position

1. Open the oven door.

2. Locate the oven door hinge locks in

both corners of the oven door, and

then rotate the hinge locks toward the

oven door to the unlocked position (see

illustration B). If the door hinge lock

is not rotated fully, the door will not

remove properly.

3. Partially close the door to engage the

door latch locks.

The door will stop at this point.

4. Using two hands, grasp the edges of

the oven door. Lift and pull the oven

door toward you and remove. You may

need to gently shift door from side to

side as you pull.

5. Set the oven door(s) aside on the

prepared covered work surface with the

oven door resting on its handle.

6. To continue with the oven installation,

go to the “Positioning Oven Feet

for Multiple Cabinet Cutout Heights”

section.

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 10DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 10 2023-04-07 오후 1:41:182023-04-07 오후 1:41:18

English 11

Installation instructions

Replace oven door(s)

CAUTION

The door is very heavy. You may need help lifting the door high enough to slide it

into the hinge slots. Do not lift the door by the handle.

A. Slot in the oven cavity for

door hinge lock

1. Using two hands, grasp side edges of

door at the midpoint.

Face the oven cavity.

2. Locate the slots on each side of the

oven cavity for the door hinge locks.

3. At a 45° angle, align door hinges with

slots in the lower front of the oven

cavity. Slowly insert door, making sure

you maintain the 45° angle. You will

know the door is engaged in the slot

when you feel a slight drop.

4. Lower the oven door to the fully open

position. If the oven door does not open

to a full 90°, repeat steps 1 through 3.

5. Locate the oven door hinge locks in the

corners of the oven door, and rotate the

hinge locks toward the oven cavity to

the locked position.

See Step 1 (illustration A) in the

“Remove Oven Door(s)” section for

proper locked position.

6. Close the oven door.

7. When the hinges are properly installed

and the door closed, there should be

an even gap between the door and the

control panel. If one side of the oven

door is hanging lower than the other,

the hinge on that side is not properly

installed.

8. Connect Wire Harness.

Double Oven

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 11DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 11 2023-04-07 오후 1:41:192023-04-07 오후 1:41:19

12 English

Installation instructions

Electrical connection

For Double Ovens

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge solid copper wire.

Make sure to ground the oven.

Failure to follow these instructions can result in death, re, or electrical shock.

This oven is manufactured with a neutral (white) power supply wire and a cabinet-

connected ground (green or bare) wire twisted together.

A. UL listed or CSA approved

conduit connector

1. Disconnect power.

2. Feed the exible conduit from the oven

through the opening in the cabinet.

3. Remove junction box cover if it is

present.

4. Install a UL listed or CSA approved

conduit connector to the junction box.

5. Route the exible conduit from the

oven to the junction box through a

UL listed or CSA approved conduit

connector.

6. Tighten screws on conduit connector.

7. See “Electrical Connection Options

Chart” to complete installation for your

type of electrical connection.

For Single Ovens

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge solid copper wire.

Electrically ground oven.

Failure to follow these instructions can result in death, re, or electrical shock.

Electrical Connection Options Chart

If your home has: Go to section:

4-wire

(1.3 cm)

½”

4-Wire Cable from Home Power Supply

3-wire

(1.3 cm)

½”

3-Wire Cable from Home Power Supply

NOTE

If the power connection is plugged in improperly, "Wire Installation Fail" appears

on the display.

Reconnect the power connection properly, and the message disappears.

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 12DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 12 2023-04-07 오후 1:41:192023-04-07 오후 1:41:19

English 13

Installation instructions

4-Wire Cable from Home Power Supply

IMPORTANT: Use the 4-wire cable from home power supply in the U.S. where local

codes do not allow grounding through neutral, New Branch circuit installations

(1996 NEC), mobile homes and recreational vehicles, new construction and in

Canada.

A. Cable from home power

supply

B. Black wires (normally L1)

C. Red wires (normally L2)

D. 4-wire exible conduit from

oven

E. Junction box

F. White wires (normally

N-neutral)

G. UL listed wire connectors

H. green wires (normally

G-ground)

I. UL listed or CSA approved

conduit connector

1. Connect the 2 black wires (B) together

using a UL listed wire connector.

2. Connect the 2 red wires (C) together

using a UL listed wire connector.

3. Untwist white wire from green (or bare)

ground wire coming from the oven.

4. Connect the 2 white wires (F) together

using a UL listed wire connector.

5. Connect the green (or bare) ground

wire (H) from the oven cable to the

green (or bare) ground wire (in the

junction box) using a UL listed wire

connector.

6. Install junction box cover.

3-Wire Cable from Home Power Supply - U.S. Only

IMPORTANT: Use the 3-wire cable from home power supply where local codes

permit a 3-wire connection.

A. Cable from home power

supply

B. Junction box

C. Black wires (normally L1)

D. White wires (normally

N-neutral)

E. green wires (normally

G-ground)

F. 4-wire exible conduit from

oven

G. Red wires (normally L2)

H. UL listed wire connectors

I. UL listed or CSA approved

conduit connector

1. Connect the 2 black wires (C) together

using a UL listed wire connector.

2. Connect the 2 white wires (D) and

the green (or bare) ground wire (of

the oven cable) using a UL listed wire

connector.

3. Connect the 2 red wires (G) together

using a UL listed wire connector.

4. Install junction box cover.

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 13DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 13 2023-04-07 오후 1:41:192023-04-07 오후 1:41:19

14 English

Installation instructions

Install oven

Install

Handle

1. Using 2 or more people, lift the oven

partially into the cabinet cutout. Hang

the install handle onto the side hook of

the oven as shown below.

NOTE

Carefully push against front oven frame.

2. Push against the seal area of the front

frame to push the oven into the cabinet

until the back surface of the front frame

touches the front wall of the cabinet.

3. Push oven completely into the cabinet

and center the oven into the cabinet

cutout.

4. Remove the tape from front trims.

• Securely fasten the oven to the

cabinet using the screws provided.

• Insert the screws through hole in

trim aligning with hole in oven

frame. Do not overtighten screws.

Barrier

WARNING

When inserting the oven, use caution not to

deform or damage the barrier underneath.

A. Trim Left

B. Trim Bottom

C. Screw

5. The bottom metal trim are shipped in

the foam packing.

To install the metal bottom trim, see

following instructions.

• Align tab of the bottom trim with a

hole in the left side trim of the unit

as shown. Repeat on the right side.

• Using one screw on each side

of the trim tab, fasten the trim

securely to the oven.

NOTE

The bottom trim piece is to cover any

unwanted gaps.

A. Trim Left

B. Trim Bottom Large

C. Screw

6. If the cutout size is larger than 3/4

inches use of the wider bottom trim is

recommended.

NOTE

To select the bottom trim properly, measure

the cutout between cabinet and oven. See

the following chart.

TYPE

Cutout 0 – 3/4”3/4” – 23/4”

IMPORTANT NOTE

Keep oven vent ducts unobstructed. The oven vent is located at the bottom of the

oven. This area could become hot during oven use. Never block this vent or place

plastic or heat-sensitive items in front of it.

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 14DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 14 2023-04-07 오후 1:41:202023-04-07 오후 1:41:20

English 15

Self-diagnosis

Temp sensor & Heater check

1. After connecting the power, check if the display works properly.

2. Remove all accessories (Gliding Rack, Flat-Rack, Smart Divider...etc.) from

inside of the oven cavity.

3. You cannot proceed with self-diagnosis if the oven cavity is hot or the door is

open.

• In this case, “Hot or door” message appears on the display.

4. To start self-diagnosis, press both Hidden Keys simultaneously for 5 seconds.

• Refer to the table below for the hidden keys for each model.

Model NV51**600S**AA NV51**600D**AA

Control panel

Off

Open/Close

Reservoir

Smart

Control

Light

Lock

(3 sec)

Settings

Off

Open/Close

Reservoir

Smart

Control

Lower

Off

Light

Settings

Upper

Hidden Key

Lock + Open/Close Reservoir

and touch “Install test” on

display.

UPPER + LOWER

and touch “Install test” on

display.

Model NV51**700S**AA NV51**700D**AA

Control panel

Off

Flex Lower

Open/Close

Reservoir

Smart

Control

Flex Upper

Off

Light

Settings

Lock(3 sec)

Off

Open/Close

Reservoir

Smart

Control

Lower

Off

Light

Settings

Upper

Hidden Key

Flex UPPER + Flex LOWER

and touch “Install test” on

display.

UPPER + LOWER

and touch “Install test” on

display.

5. If there is no error, 'PASS' appears on the display with an alert sound.

6. If there is an error, following message appears on the display with an alert

sound.

Model All models

Error code Remark

Feature

Upper Broil Upper Broil Fail Double/Single Oven

Upper Bake Upper Bake Fail

Lower Broil Lower Broil Fail Double Oven Only

Lower Bake Lower Bake Fail

7. If an error occurs, contact a Samsung service center for further service.

NOTE

If you see any other error messages that are not listed above, please contact a

Samsung service center. call e.g. 1-800-SAMSUNG (726-7864)

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 15DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 15 2023-04-07 오후 1:41:202023-04-07 오후 1:41:20

DG68-01561A-00

Scan the QR code* or visit

www.samsung.com/spsn

to view our helpful

How-to Videos and Live Shows

* Requiere la instalación de un lector en su

teléfono inteligente

Scan this with your smartphone

Please be advised that the Samsung warranty does NOT cover service calls to explain product operation, correct improper installation, or perform normal cleaning or

maintenance.

QUESTIONS OR COMMENTS?

COUNTRY CALL OR VISIT US ONLINE AT

U.S.A

Consumer Electronics 1-800-SAMSUNG (726-7864) www.samsung.com/us/support

CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca/support (English)

www.samsung.com/ca_fr/support (French)

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 16DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 16 2023-04-07 오후 1:41:202023-04-07 오후 1:41:20

Horno eléctrico empotrado en pared

Manual de instalación

NV51**700**AA / NV51**600**AA

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 1DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 1 2023-04-07 오후 1:41:212023-04-07 오후 1:41:21

2 Español

Contenido

ContenidoContenido

Información sobre seguridad 2

Seguridad de los equipos relacionados 2

Transporte 2

Preparación 4

Lista de vericación 4

Preparación para instalar el horno 4

Requisitos de ubicación 5

Dimensiones del producto: hornos simples (NV51**700S, NV51**600S) 5

Dimensiones del gabinete: hornos simples 6

Dimensiones del producto: hornos dobles (NV51**700D, NV51**600D) 7

Dimensiones del gabinete: hornos dobles 7

Instrucciones de instalación 9

Preparar el horno empotrado 9

Cómo retirar y reemplazar la(s) puerta(s) del horno 10

Conexión eléctrica 12

Cómo instalar el horno 14

Autodiagnóstico 15

Sensor de temperatura y control del calentador 15

Información sobre seguridad

Seguridad de los equipos relacionados

Retire toda la cinta y el empaque antes de usar el artefacto. Deseche el empaque luego de

quitar el artefacto. Nunca deje que los niños jueguen con el material de empaque.

Nunca modique o altere la construcción del artefacto. Por ejemplo, no quite paneles,

portacables o tornillos.

Transporte

Utilice el método de transporte que se ilustra a continuación a n de evitar que se dañe la

ventilación del horno.

A. Parte delantera

B. Palé

Sostenga la parte inferior del horno de ambos

lados al desplazarlo hacia su ubicación de

instalación. Deje la unidad en el palé de envío

hasta que esté frente a la abertura del gabinete y

esté listo para colocarlo en su lugar.

PELIGRO

PELIGRO DE ELECTROCUCIÓN

Para evitar el riesgo de electrocución, lesiones físicas o la muerte, verique que el artefacto

esté conectado a tierra correctamente de conformidad con los códigos locales o, en su

ausencia, con el Código eléctrico nacional (NEC). Versión más reciente de ANSI/NFPA 70.

ADVERTENCIA

PELIGRO DURANTE EL TRASLADO

Este artefacto requiere de dos o más personas para manipularlo o trasladarlo a n de evitar

el riesgo de sufrir lesiones personales graves. Se recomienda el uso de dispositivos para el

transporte del artefacto.

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 2DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 2 2023-04-07 오후 1:41:222023-04-07 오후 1:41:22

Español 3

Información sobre seguridad

ADVERTENCIA

• La información de este manual debe seguirse rigurosamente.

- De lo contrario, podrían producirse incendios o descargas eléctricas causantes de

daños a la propiedad, lesiones personales, o la muerte.

• Importante: Conserve este manual de instalación para que pueda ser consultado por el

inspector del servicio eléctrico de su localidad.

• Instalación adecuada: Asegúrese de que el artefacto se encuentre correctamente instalado

y conectado a tierra por un técnico calicado.

• Las nuevas construcciones de circuitos ramales (1996 NEC), casas rodantes, vehículos

recreativos e instalaciones donde los códigos locales prohíben la conexión a

tierra mediante el conductor neutro, requieren conexiones de circuitos ramales de

4 conductores.

• Si el cableado de aluminio de la casa no se conecta adecuadamente a los cables de cobre

podría existir riesgo de electrocución o incendio. Solo utilice conectores diseñados para

unir cobre con aluminio y siga el procedimiento recomendado por el fabricante del

conector.

• Se deben utilizar tornillos de montaje.

- De lo contrario, el horno podría caerse del gabinete y ocasionar lesiones graves.

PRECAUCIÓN

• Asegúrese de que los gabinetes y los revestimientos de las paredes alrededor del horno

puedan soportar las temperaturas (hasta 194 °F [90 °C]) que este genera.

- Se podrían producir alteraciones de color, deslaminación o derretimiento.

• NO quite los separadores de las paredes laterales del horno empotrado.

- Estos centran el horno en el espacio provisto. El horno debe estar centrado para

evitar la acumulación excesiva de calor que puede provocar daños o incendios.

ADVERTENCIA

• La información de este manual debe seguirse rigurosamente.

- De lo contrario, podrían producirse incendios o descargas eléctricas causantes de

daños a la propiedad, lesiones personales, o la muerte.

NOTA IMPORTANTE

La instalación adecuada es responsabilidad del instalador y la falla del producto debido a una

instalación inadecuada no está cubierta por la Garantía.

ADVERTENCIA

• NO coloque ningún peso sobre la puerta del horno. Nunca nadie se debe trepar, sentar,

parar o colgar de la puerta del horno.

- El horno podría inclinarse y producir lesiones ya sea por los alimentos calientes o el

mismo horno.

ADVERTENCIA

• Cuando se realizan las conexiones eléctricas, la alimentación eléctrica debe estar cortada.

- De lo contario, se podrían producir lesiones personales graves, descargas eléctricas

o la muerte.

NOTA IMPORTANTE

• Cumpla todos los códigos y ordenanzas exigidos por las autoridades pertinentes. Este

electrodoméstico debe conectarse a tierra correctamente.

• Mantenga los conductos de ventilación del horno libres de obstrucciones. La abertura

de ventilación del horno está ubicada en la parte inferior del horno. Esta área podría

calentarse durante el uso del horno. Nunca tapone esta abertura de ventilación ni coloque

elementos de plástico o sensibles al calor frente a dicha abertura.

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 3DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 3 2023-04-07 오후 1:41:222023-04-07 오후 1:41:22

4 Español

Preparación

Lista de vericación

Use esta lista de vericación para comprobar que ha completado todos los pasos del proceso

de instalación. Esto puede ayudarlo a evitar errores.

1. Antes de instalar el horno, asegúrese de vericar que las dimensiones del gabinete sean

las adecuadas para la unidad y que las conexiones eléctricas necesarias estén presentes.

2. Consulte el manual de instalación para ver contenido sobre Seguridad, Dimensiones del

gabinete, Desempaque, Instalación eléctrica, Prueba de la instalación y Servicio al Cliente.

3. Para levantar el horno, cuelgue la manija de instalación en el gancho lateral de la unidad.

4. Coloque el horno frente a la abertura del gabinete, dejando el empaque inferior en la

unidad para evitar dañar el piso.

5. Levante la unidad con ayuda de otras personas y colóquela directamente en el recorte

del gabinete cuidando de no agarrarse los dedos o rasparse las manos o los brazos.

Asegúrese de que el conducto eléctrico alcance bien el punto de conexión.

6. Deslice la unidad hasta el lugar deseado asegurándose de ir llevando el conducto

eléctrico correctamente.

7. Ajuste el horno a la abertura del gabinete con los tornillos provistos (usando un

destornillador Philips).

8. Consulte las instrucciones de instalación completas y siga el resto de los procedimientos

indicados, incluida la prueba de funcionamiento.

9. Junto con el horno, se suministran las instrucciones del producto y los accesorios

(envueltos o en caja).

10. INSTALADOR: Las instrucciones y los accesorios deben quedar en manos del cliente.

11. Cuelgue la manija de instalación en el gancho lateral del horno.

Preparación para instalar el horno

Destornillador Phillips Taladro

Preparación para instalar el horno

6 tornillos (M4 L16)

6 tornillos de montaje para

madera (4 necesarios para la

instalación y 2 adicionales)

30” (76.2 cm)

Borde inferior de metal

Manija de instalación

(solo para horno doble)

Materiales necesarios

Caja de empalmes Conectores de torsión Conector de conducto de 3/4”

DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 4DG68-01561A-00_IM_NV7000C_NV51xx600xxxAA_EN+MES+CFR.indb 4 2023-04-07 오후 1:41:222023-04-07 오후 1:41:22

La page charge ...