Modern Forms PD-51318 Gilt Mode d'emploi

Taper
Mode d'emploi
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2014
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en posi
tion d’arrêt (« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel quil est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.
HARDWARE C1 E1 I1 J1 L1 M1 B1
INSTALLATION INSTRUCTION
GILT
PD-51318
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2014
INSTALLATION INSTRUCTION
GILT
PD-51318
PREPARATION
1. Shut o the power at the circuit breaker and remove
existing xture, including the mounting hardware.
2. Carefully unpack your new xture and lay out
all the parts on a clear area. Be careful not to lose
any small parts necessary for installation.
MOUNTING THE FIXTURE (FIG.1)
3. Place the glass (O1) into the ring (P1). Secure them to the top
inside of metal shade (N1) using the long screw (L1) and washer
(M1).
4. Place the glass panel (K1) (frosted side face down) onto the top
of the metal shade (N1). Secure it using the short screws (I1) and
plastic washers (J1).
5. Secure the mounting plate (D1) to the junction box (A1) using
junction box screw (E1). The side of the mounting plate marked
“GND” must face out.
6. Unscrew the set-screw on canopy spider with a at-head
screw-driver (not provided).
7. Adjust the cable wires to desired length and tighten set screws.
8. Adjust the strain relief (Q1) near the wiring holes.
CONNECTING THE WIRES (FIG.2)
9. Connect the transformer input wires to supply wires as shown
in Fig.2, making sure that all wire connectors (C1) are secured.
Cut the two wires marked “24V AC” leaving at least 6” length and
connect to the transformer output wires (red). Make sure that all
wire connectors are secured.
Note: The xture wire has two braided layers.
Strip two layers carefully.
10. If your outlet box has a ground wire, connect it to the xture’s
ground wire. Otherwise, connect the xtures ground wire directly
to the mounting plate (D1) using the green screw provided. Tuck
wires carefully inside the junction box.
11. Place the canopy (F1) over the mounting plate (D1) and
secure with ball nuts (B1). Thread the ceiling pan (H1) onto the
canopy (F1) clockwise until tight.
FIG.2
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare Copper
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
A1
C1
G1
E1
D1
F1
Q1
B1
H1
I1
J1
K1
L1
M1
N1
O1
P1
FIG.1
  • Page 1 1
  • Page 2 2

Modern Forms PD-51318 Gilt Mode d'emploi

Taper
Mode d'emploi