Modern Forms PD-55718 Yolo Mode d'emploi

Modern Forms
Marque
Modern Forms
Modèle
PD-55718 Yolo
Taper
Mode d'emploi
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
557 - LED Pendant
PD-55718, PD-55726
Wire Connector
Qty: 3 pcs + 1 Extra
Junction Box Screw
Qty: 2 pcs + 1 Extra
#8-32x1
Zinc Plating
Mounting Screw
Qty: 1 Extra
5/32-32x1/2
GL / SL
A1 B1 C1
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut o the power at the circuit breaker and remove existing
xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on
a clear area. Be careful not to lose any small parts necessary
for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screw (C1) from the xture.
Disconnect the Driver’s output wire.
4. Connect the driver input wires with supply wires as shown in
Fig. 2, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire,
connect the xture’s ground wire to it. Otherwise, connect
the xture’s ground wire directly to the mounting plate using
the green screw provided. After wires are connected, tuck
them carefully inside the junction box.
*Requires Driver to be recessed within the junction box.
MOUNTING THE FIXTURE (Fig. 1)
5. Secure mounting plate to the junction box using junction
box screws (B1). The side of the mounting plate marked
“GND” must face out. Pull out the driver output wire.
6. Choose the number of down rods suitable of your
application.
7. Thread the xture wire through the rods, swivel and canopy.
Connect the canopy, swivel, rods and xture body. Make sure
all are tightened.
8. Connect the driver output wires with xture wire as shown in
Fig. 2, making sure that all wire connectors ( A1) are secured.
9. Twist lock the glass diuser to xture shade.
10. Place the xture over the mounting plate and secure it with
mounting screws (C1).
11. For slope ceiling application, rotate swivel at the top of the
stem to ensure luminaries is aiming down (Fig. 3).
FIG. 1
Back Plate Dimensions
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
GND
Knurling Nut
Junction Box Screw
Mounting Screw
Canopy
Rod
(RPL-ROD-IN06-WTA)
(RPL-ROD-IN12-WTA)
(RPL-ROD-IN06-BZ)
(RPL-ROD-IN12-BZ)
Fixture Shade
Glass Diuser
Output
Mounting Plate
Junction Box
Fixture Wire
Input
Drive A1
B1
C1
Fig. 3
Turn to down
1/2"
4 1/2"
1 3/4"
1 3/8"
INSTALLATION INSTRUCTION
557 - LED Pendant
PD-55718, PD-55726
1
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program. JAN 2019
INSTALLATION INSTRUCTIONS
148– LED Wall Sconce
WS-14818/WS-14824/WS-14836
HARDWARE
Mounti
Qty: 1 Extra
7MPF0409S3(CH/BN)
7MPF0409S3BK(BK)
5/32”-32X5/16
C
Junction Box Screw
Qty: 4pcs+2 Extra
#8-32x5/8 SS
B
Mounting Ring
Qty:1pc
7MBC101501
D
Driver
Qty:1pc
LD-700MA28U-IS-P
E
Conversion Plate
Qty:1pc
4MBC221104BN
4MBC221104CH
4MBC221104B4
SPCC
F
Mounting Screw
Qty: 1 Extra
7MPF0409S3(CH/BN)
7MPF0409S3BK(BK)
5/32"-32X5/16
C
Mounting Ring
Qty:1pc
7MBC101501
D
Conversion Plate
Qty:1pc
4MBC221104BN
4MBC221104CH
4MBC221104B4
SPCC
EF
Driver
Qty:1pc
LD-700MA28U-IS-P
Junction Box Screw
ty: 4pcs+2 Extra
#8-32x5/8 SS
B
F
7MPF0415C2
0415C2
Binding Collar
Qty:1 pc
Set Screws
Qty: 2 pcs
Wire Connector
Qty: 4 pcs Qty: 1 pc
A B C D
557- LED Pendant
PD-55735
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec
les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce produit
dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez contacter un
revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un
chiffon humide.
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE BEGINNING.
-Read all instructions before installing.
-System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
-Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch
”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on.
-Place the wall switch in the “OFF” position.
- Lisez toutes les instructions avant l’installation.
- Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
- Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could result
in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or
missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal
areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
Back Plate Screw
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
2
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program. JAN 2019
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for
installation.
MOUNT ON 2”X4” SWITCH BOX (Fig. 1)
3. Remove the mounting screw (C) from the xture, and then take down the mounting back plate.
4. Connect the Driver (F) input wires (F) to switch box wires as shown in Fig. 3, making sure that all wire connectors (A) are
secured. If your outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect
the xture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them
carefully inside the switch box.
*
Requires Driver to be recessed in the switch box.
OR
148– LED Wall Sconce
WS-14818/WS-14824/WS-14836
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
A
C
Wire Connector
Ground Wire
Mounting Screw
Switch Box
3/4”
(check part# in haedware)
C
Mounting Screw
A
Wire Connector
Ground Wire
Switch Box
1 5/8” 1 3/8”
3. Remove the back plate screw (B) and back plate from the fixture.
5.
4.
MOUNTING THE FIXTURE (Fig. 1)
COMPLETING THE INSTALLATION
1. Shut o the power at the circuit breaker and remove existing
xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on
a clear area. Be careful not to lose any small parts necessary for installation.
6.
7.
Choose the number of downrods suitable for your application.
Thread the safety cords and fixture wire through the rods, swivel
and canopy. Connect the canopy, rods and fixtures body, Make
sure all are tightened.
Loosen the two set screws (C) on binding collar (D), place the
safety cords across the binding collar (D) as shown (Fig. 1), and
tighten the the two set screws (C) after adjusting the safety cord
length.
Secure back plate to junction box using the screws provided with
the junction box.
NOTE: The side of the back plate marked "GND" must face out.
CONNECTING THE WIRES (Fig. 2)
8.
Connect the fixture wires to junction box wires as shown
(Fig. 2). Make sure that all wire connectors (A) are secure. If
your outlet box has green or bare copper ground wire,
connect the fixture’s ground wire to it. Otherwise, connect
the fixture’s ground wire directly to the back plate using the
green screw provided. After wires are connected, tuck them
carefully inside the junction box.
Twist lock the glass diffuser to fixture shade.
10. Secure the xture to the
back plate using the back plate screw (B).
For slope ceiling application, rotate swivel at the top of the stem
to ensure luminaries is aiming down (Fig.3).
557- LED Pendant
PD-55735
Junction Box
Supply wire
Canopy
Wire Connector
Back Plate
Junction Box Screw
Back Plate Screw
Fixture Shade
Glass Diffuser
Glass
(RPL-GLA-55735-GL)
(RPL-GLA-55735-SL)
Fixture Wire
Binding Collar
Set Screws
Ground Wire Screw
Rod 3X12"
Rod 1X6"
A
B
D
C
Safety Cord
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring Back Plate
Fig.1
Φ4 7/8”
1 3/4” 1 3/8”
Fig.3
MAX30
9.
11.
INSTALLATION INSTRUCTIONS
PREPARTION
Swivel
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Modern Forms PD-55718 Yolo Mode d'emploi

Modern Forms
Marque
Modern Forms
Modèle
PD-55718 Yolo
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents