Ryobi RY401200 Le manuel du propriétaire

Marque: Ryobi

Modèle: RY401200

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Ce tondeuse a été conçu et fabriqué conformément à nos strictes

normes de fiabilité, simplicité d’emploi et sécurité d’utilisation.

Correctement entretenu, cet outil vous donnera des années de

fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

Su podadora ha sido diseñado y fabricado de conformidad con

nuestras estrictas normas para brindar fiabilidad, facilidad de uso

y seguridad para el operador. Con el debido cuidado, le brindará

muchos años de sólido funcionamiento y sin problemas.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your lawn mower has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

16 in., 40 VOLT LAWN MOWER

16 po 40V TONDEUSE

16 pulg. 40V PODADORA

RY40100

ALL VERSIONS

TOUTES LES VERSIONS

TODAS LAS VERSIONES

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner

toutes les figures mentionnées dans le manuel

d’utilisation.

Consulte esta sección desplegable para ver todas

las figuras a las que se hace referencia en el

manual del operador.

iii

Fig. 1

Fig. 2

Fig. 4

Fig. 3

A - Lower handle (poignée inférieure, mango

inferior)

B - Lower handle lock (verrou de la poignée

inférieure, seguro del mango inferior)

C - Loosen (desserrer, aflojar)

D - Tighten (serrer, apriete)

E - Slot (fente, ranura)

A - Rear discharge door (couvercle d’éjection

arrière, puerta de descarga posterior)

B - Rear discharge opening (ouverture

d’éjection arrière, abertura de descarga

posterio)

C - Mulching plug (insert broyeur, tapón para

trituración)

A - Upper handle lock (verrou de la poignée

supérieure, seguro del mango superior)

B - Lower handle lock (verrou de la poignée

inférieure, seguro del mango inferior)

C - Open (ouvir, abra)

A - Battery cover (couvercle des piles, tapa de

las baterías)

B - Motor/blade control assembly (dispositif

de commande du moteur/de la lame,

conjunto de control del motor/hoja)

C - Start button (bouton « Start » [démarrer],

botón de arranque)

D - Upper handle (poignée supérieure, mango

superior)

E - Bail (anse, asa)

F - Upper handle lock (verrou de la poignée

supérieure, seguro del mango superior)

G - Lower handle (poignée inférieure, mango

inferior)

H - Lower handle lock (verrou de la poignée

inférieure, seguro del mango inferior)

I - Height adjustment lever (levier de réglage

de la hauteur, palanca de ajuste de altura)

J - Mulching plug (insert broyeur, tapón para

trituración)

K - Key (clé, llave)

L - Grass catcher (collecteur d’herbe, receptor

de hierba)

M - Carrying handle (poignée de transport,

mango de acarreo)

D - Close (fermeture, cerrar)

E - Knob (bouton, perilla)

F - Starter cable (câble de démarreur, cable del

arrancador)

Fig. 9

A - Key (clé, llave)

B - Battery cover (couvercle des piles, tapa de

las baterías)

C - Key slot (fente de la clé, ranura de la llave)

A - Battery pack (bloc-piles, paquete de

baterías)

B - Battery cover (couvercle des piles, tapa de

las baterías)

C - Battery port (logement de piles, receptáculo

para baterías)

D - Latch (loquet, pestillo)

Fig. 7

A - Height adjustment lever (levier de réglage

de la hauteur, palanca de ajuste de altura)

B - Lowest blade setting (le plus bas réglage

de la lame, ajuste más bajo de la hoja)

C - Highest blade setting (le plus haut réglage

de la lame, ajustes de cuchilla más alto)

A - Bail (anse, asa)

B - Start button(bouton « Start » [démarrer],

botón de arranque)

C - Upper handle (poignée supérieure, mango

superior)

Fig. 5

Fig. 6

A - Grass catcher handle (poignée de

collecteur d’herbe, mango del receptor de

hierba)

B - Slots (fentes, ranuras)

C - Rear door (couvercle d’éjection, puerta de

descarga)

Fig. 8 Fig. 10

D - Rear discharge opening (ouverture

d’éjection latérale, abertura de descarga

lateral)

E - Door rod (barre de couvercle, barra de la

puerta)

F - Hooks (crochets, ganchos)

A - Slots (fentes, ranuras)

B - Hooks (crochets, ganchos)

Fig. 13

Fig. 14

Fig. 15

A - Blade (lame, hoja)

B - Wrench (clé, llave)

C - Block of wood (pièce de bois, bloque de

madera)

A - Fan assembly (ensemble de ventilateur,

conjunto del ventilador)

B - Shaft (arbre, eje)

C - Blade (lame, hoja)

D - Blade insulator (isolant de lame, aislante

de hoja)

E - Spacer (entretoise, separador)

F - Blade nut (écrou de lame, tuerca de la

hoja)

G - Blade posts (tiges pour lame, montantes

de cuchilla)

Fig. 12

Fig. 11

TO STORE THE MACHINE

POUR REMISER L’ÉQUIPEMENT

PARA GUARDAR LA MÁQUINA

15° MAXIMUM

15° MAXIMAL

15° MÁXIMA

2 — English

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 Important Safety Instructions ........................................................................................................................................3-4

Règles de sécurité générales / Reglas de seguridad generales

Symbols ......................................................................................................................................................................... 5-6

Symboles / Símbolos

 Features ............................................................................................................................................................................7

Caractéristiques / Características

 Assembly .......................................................................................................................................................................7-8

Assemblage / Armado

 Operation ..................................................................................................................................................................... 9-10

Utilisation / Funcionamiento

 Maintenance ..............................................................................................................................................................10-11

Entretien / Mantenimiento

 Troubleshooting .............................................................................................................................................................. 12

Dépannage / Solución de problemas

 Warranty ......................................................................................................................................................................... 13

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

3 — English

WARNING:

READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below and on the

machine may result in electric shock, fire, and/or serious

personal injury.

READ ALL INSTRUCTIONS

This cutting machine is capable of amputating hands and

feet and throwing objects. Failure to observe all safety

instructions could result in serious injury or death.

Avoid dangerous environment - Do not use the lawn

mower in damp or wet conditions or operate in the rain.

Keep children away - Keep all bystanders, children, and

pets at least 100 ft. away. Stop machine if anyone enters

the area.

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that

children will remain where you last saw them.

• Keep children out of the mowing area and under the

watchful care of a responsible adult other than the

operator.

• Be alert and turn mower off if a child enters the area.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs,

trees, or other objects that may block your view of a

child.

Dress properly - Wear heavy, long pants, long sleeves,

boots, and gloves. Do not wear loose fitting clothing,

short pants, sandals, or go barefoot. Do not wear jewelry

of any kind. They can be caught in moving parts.

Don’t overreach - Keep proper footing and balance at all

times. Overreaching can result in loss of balance.

Do not operate the equipment while barefoot or when

wearing sandals or similar lightweight footwear. Wear

protective footwear that will protect your feet and improve

your footing on slippery surfaces.

Do not leave the mower unattended while running or with

the key installed.

Keep hands and feet away from cutting area. Keep clear

of the discharge opening at all times.

Operate the lawn mower only in daylight or good artificial

light.

Always wear safety glasses with side shields. Everyday

glasses have only impact resistant lenses. They are NOT

safety glasses. Following this rule will reduce the risk of

eye injury. Use face mask if operation is dusty.

Use safety glasses - Always wear eye protection with

side shields marked to comply with ANSI Z87.1. Use face

mask if operation is dusty.

Use the right appliance - Do not use the lawn mower for

any job except that for which it is intended.

Do not force the lawn mower - It will do the job better

and safer at the rate for which it was designed.

Stay alert - Watch what you are doing and use common

sense when operating the lawn mower. Do not operate

the mower while tired, upset or under the influence of

drugs, alcohol, or medication. A moment of inattention

while operating the lawn mower may result in serious

personal injury.

Maintain lawn mower with care - Keep machine in good

working condition. Keep blades sharp and guards in place

and in working order. Replace damaged or unevenly worn

blades before using mower for best performance.

Check all nuts, bolts, and screws at frequent intervals

for proper tightness to be sure the equipment is in

safe working condition. Mower blades are sharp. Wrap

the blade or wear gloves, and use extra caution when

servicing them.

Do not dispose of the battery in a fire. The cell may

explode. Check with local codes for possible special

disposal instructions.

Stop the motor, wait until the blade comes to a complete

stop, and remove the key and battery pack before

cleaning the lawn mower, removing the grass catcher,

or removing the mulching plug.

 Replace blade if it is bent or cracked. An unbalanced

blade causes vibration that could damage the motor

drive unit or cause personal injury. Sharpen a dull blade

equally at each end to maintain the balance. Clean the

blade thoroughly and check its balance by supporting it

horizontally on a thin nail through its center hole. The nail

should be in a horizontal position. If either end of the blade

rotates downward, remove some metal from the heavy

of lower end until the blade is balanced. It is balanced

when neither end drops.

When not in use, mower should be stored indoors in a

dry, locked up place—out of the reach of children. The

key should also be removed and stored in a separate

location out of the reach of children.

Always use safety protective devices. Do not operate the

mower without the entire grass catcher, mulching plug

and rear discharge door in place and working properly.

Do not open or mutilate the battery. Released electrolyte

is corrosive and may cause damage to the eyes or skin.

It may be toxic if swallowed.

Follow manufacturer’s instructions for proper operation

and installation of accessories. Only use accessories

approved by the manufacturer.

Exercise care in handling batteries in order not to short the

battery with conducting materials such as rings, bracelets,

and keys. The battery or conductor may overheat and

cause burns.

IMPORTANT SAFETY INSTRUCTIONS

4 — English

IMPORTANT SAFETY INSTRUCTIONS

Clear the work area before each use. Remove all objects

such as rocks, sticks, metal, wire, bones, toys, or other

objects which can be thrown by the blade.Stay behind

the handle when the motor is running.

Avoid holes, ruts, bumps, rocks, property stakes, or other

hidden objects. Uneven terrain could cause a slip and fall

accident.

Do not mow near drop-offs, ditches, or embankments.



Mow across the face of slopes, never up and down. Exercise

extreme caution when changing direction on slopes.



Plan your mowing pattern to avoid discharge of material

toward roads, sidewalks, bystanders and the like. Also, avoid

discharging material against a wall or obstruction, which may

cause the material to ricochet back toward the operator.

Do not mow on wet grass or excessively steep slopes.

Poor footing could cause a slip and fall accident. Walk,

never run.

Use extra care when approaching blind corners, shrubs,

trees, or other objects that may block your view.



Do not pull the mower backward unless absolutely

necessary. If you must back the mower away from a wall

or obstruction, first look down and behind to avoid tripping

or pulling the mower over your feet.

Never direct discharged material toward anyone. Avoid

discharging material against a wall or obstruction. Ma-

terial may ricochet back toward the operator. Stop the

blade when crossing gravel surfaces.

Objects struck by the lawn mower blade can cause severe

injuries to persons. The lawn should always be carefully

examined and cleared of all objects prior to each mowing.

If the lawn mower strikes a foreign object, follow these

steps:

•

Stop the lawn mower by releasing the bail, wait until the

blade comes to a complete stop, and then remove key.

• Thoroughly inspect the mower for any damage.

• Replace the blade if it is damaged in any way. Repair

any damage before restarting and continuing to operate

the mower.

Stop the motor, wait until the blade comes to a complete

stop, and remove key before unclogging the chute. The

cutting blade continues to rotate for a few seconds after

the motor is shut off. Never place any part of the body in

the blade area until you are sure the blade has stopped

rotating.

If the mower should start to vibrate abnormally, stop the

motor and check immediately for the cause. Replace

the blade if it is unevenly worn or damaged in any way.

Vibration is generally a warning of trouble.

Service on the product must be performed by qualified

repair personnel only. Service or maintenance performed

by unqualified personnel could result in injury to the user

or damage to the product.

Use only authorized replacement parts when servicing

the product. Use identical replacement blades only. Use

of unauthorized parts may create a risk of serious injury

to the user, or damage to the product.

Maintain or replace safety instructions labels, as

necessary.

Disconnect battery- Disconnect battery pack from the

appliance before storing, servicing, transporting, or chang-

ing accessories such as blades. Such preventive safety

measures reduce the risk of starting the tool accidentally.

Stop the unit and disconnect battery pack and key when

not in use. Carry or push the unit with the motor stopped

and the key and battery pack removed from the mower.

Battery tools do not have to be plugged into an electrical

outlet; therefore, they are always in operating condition.

Be aware of possible hazards when not using your bat-

tery tool or when changing accessories. Following this

rule will reduce the risk of electric shock, fire, or serious

personal injury.

 Do not use battery-operated appliance in rain.

 Remove or disconnect battery before servicing, cleaning

or removing material from the gardening appliance.



Use battery only with charger listed. For use with 40V

lithium-ion battery packs. See Tool/ Appliance/Battery Pack/

Charger Correlation Supplement 988000-842.

 Store idle appliances indoors- When not in use, mower

should be stored indoors in a dry, locked place out of the

reach of children.



Follow instructions for lubricating and changing accessories.



Keep guards in place and in working order.



Keep blades sharp.



Keep hand and feet away from cutting area.



Only allow responsible adults, who are familiar with the

instructions, to operate this machine.



Never operate machine in a closed area.



Never tamper with safety devices. Check for proper

operation regularly.



Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you

loan someone this tool, loan them these instructions also.

5 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Electric Shock Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Keep Hands and Feet Away Keep hands and feet away from blade and cutting area.

No Reach Do not reach hands or feet under mower deck.

No Slope Do not operate on inclines greater than 15º. Mow across the face

of slopes, never up and down.

Keep Children and

Bystanders Away Keep all children and bystanders at least 100 ft. away.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE: (Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

SYMBOLS

6 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Recycle Symbols

This product uses lithium-ion (Li-ion) batteries. Local, state, or

federal laws may prohibit disposal of batteries in ordinary trash.

Consult your local waste authority for information regarding

available recycling and/or disposal options.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

SYMBOLS

7 — English

PRODUCT SPECIFICATIONS

Battery ...................................................................... 40 Volt

Cutting Path ............................................................... 16 in.

Height Adjustments .................................3/4 in. to 2-3/4 in.

Wheel Size ..................................... 5-3/4 in. front, 7 in. rear

Weight ........................................................................ 40 lb.

FEATURES

KNOW YOUR LAWN MOWER

See Figure 1.

The safe use of this product requires an understanding of

the information on the product and in this operator’s manual

as well as a knowledge of the project you are attempting.

Before use of this product, familiarize yourself with all op-

erating features and safety rules.

BATTERY COVER

The battery cover protects the battery port from moisture

and debris.

CARRYING HANDLE

The lawn mower has a carrying handle for easy transport.

KEY

The key must be inserted before the mower can be started.

GRASS CATCHER

The grass catcher collects grass clippings and prevents them

from being discharged across your lawn as you mow.

HEIGHT ADJUSTMENT LEVER

The height adjustment lever provides cutting height

adjustments.

MOTOR/BLADE CONTROL ASSEMBLY

The motor/blade control, located on the upper handle of the

mower, engages and disengages the motor and blade.

MULCHING PLUG

Your mower is equipped with a mulching plug that covers

the rear discharge opening, which allows the mower blade

to cut and recut for finer clippings.

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Lawn Mower

Key

Mulching Plug

Grass Catcher

Operator’s Manual

WARNING:

If any parts are damaged or missing, do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

8 — English

WARNING:

Do not insert key or battery pack until assembly is

complete and you are ready to mow. Failure to comply

could result in accidental starting and possible serious

personal injury.

WARNING:

To prevent accidental starting, do not make any adjust-

ments or installations with the key or battery pack in-

serted. Accidental starting of the mower during assembly

could result in serious personal injury.

WARNING:

Never operate the mower without the proper safety de-

vices in place and working. Never operate the mower with

damaged safety devices. Operating the mower with miss-

ing or damaged parts can result in serious personal injury.

UNFOLDING AND ADJUSTING HANDLE

ASSEMBLY

See Figures 2 - 3.

To raise handle assembly:

 Open the lower handle locks.

 Pull up and back on the lower handle until it is aligned

with the slot between the handle locks and the mower

housing.

NOTE: If the lower handle is difficult to move, turn the

lower handle locks clockwise to free the handle.

 To secure the lower handle in place, close the lower handle

locks.

NOTE: If the lower handle is loose or does not seat

completely in the slot, turn the lower handle locks coun-

terclockwise to secure the handle.

 Open the upper handle locks.

 Pull up and back on the upper handle to raise it into

operating position. Make sure that the lower handle is

seated in the grooves at the bottom of the upper handle.

NOTICE:

Do not allow the starter cable to become pinched or

trapped when raising the handle.

 To secure the upper handle in place, close the upper

handle locks.

NOTE: If the upper handle is loose or separated from

the lower handle, tighten the knobs on the upper handle

locks by turning them clockwise.

To lower the handle assembly:

 Open the upper handle locks.

NOTE: If the handle lock is difficult to open, loosen the

knobs on the upper handle locks by turning them coun-

terclockwise.

ASSEMBLY

 Lower the upper handle.

 Open the lower handle lock.

 Push outward on each side of the lower handle until it

is free from the slot. Then, fold the handle to the front of

the unit. Avoid pinching or trapping any cables.

INSTALLING THE MULCHING PLUG

(FOR MULCHING OPERATION)

See Figure 4.

NOTE: When using the mulching plug, do not install the

grass catcher.

 Remove key and battery pack.

 Lift and hold the rear discharge door.

 Grasp the mulching plug by its handle and insert it at a

slight angle, as shown.

 Push the mulching plug securely into place.

 Lower the rear discharge door.

 Reinstall key and battery pack when you are ready to

mow.

INSTALLING THE GRASS CATCHER (FOR

REAR BAGGING OPERATION)

See Figures 5 - 6.

NOTE: When using the grass catcher, do not install the

mulching plug.

 Remove key and battery pack.

 Lift the rear discharge door.

 Lift the grass catcher by its handle and place under the

rear discharge door so that the hooks on the grass catcher

are seated onto the slots on the mower housing.

 Release the rear discharge door.

 Reinstall key and battery pack when you are ready to

mow.

SETTING BLADE HEIGHT

See Figure 7.

When shipped, the wheels on the mower are set to a low-

cutting position. Before using the mower for the first time,

raise the cutting position to the height best suited for your

lawn. The average lawn should be between 1-1/2 in. to 2 in.

during cool months and between 2 in. and 3-1/4 in. during

hot months.

To adjust the blade height:

 Remove key and battery pack.

 To raise the blade height, grasp the height adjustment

lever and move it toward the back of the mower.

 To lower the blade height, grasp the height adjustment

lever and move it toward the front of the mower.

 Reinstall key and battery pack when you are ready to

mow.

9 — English

OPERATION

WARNING:

Do not allow familiarity with products to make you care-

less. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

WARNING:

Always inspect mower for missing or damaged parts

and blade for damage, uneven, or excessive wear prior

to use. Use of the mower with damaged or missing parts

can result in serious personal injury.

This product will accept Ryobi 40V lithium-ion battery packs

only.

For complete charging instructions, refer to the Operator’s

Manuals for your Ryobi battery pack and charger models.

BATTERY PROTECTION FEATURES

Ryobi lithium-ion batteries are designed with features that

protect the lithium-ion cells and maximize battery life.

If the tool stops during use, release the bail to reset and

resume operation. If the tool still does not work, the battery

needs to be recharged.

WARNING:

Always remove battery pack and key from your tool when

you are assembling parts, making adjustments, cleaning,

or when not in use. Removing battery pack and key will

prevent accidental starting that could cause serious

personal injury.

TO INSTALL BATTERY PACK

See Figure 8.

 Raise the battery cover.

 Place the battery pack in the mower. Align raised ribs on

battery pack with grooves in the mower’s battery port.

WARNING:

Make sure the latch on the bottom of the battery pack

snaps in place and the battery pack is fully seated and

secure in the mower’s battery port before beginning

operation. Failure to securely seat the battery pack could

cause the battery pack to fall out, resulting in serious

personal injury.

 Lower the battery cover.

TO REMOVE BATTERY PACK

See Figure 8.

 Raise the battery cover.

 Press and hold the battery latch button at the bottom of

the battery pack.

 Remove battery pack from the mower.

WARNING:

To avoid serious personal injury, always remove the battery

pack and key when carrying or transporting the tool.

APPLICATIONS

You may use this product for the purpose listed below:

Mowing your lawn

STARTING/STOPPING THE MOWER

See Figures 9 - 10.

Raise the battery cover.

Install battery pack.

Insert the key into the slot beside the battery port.

Lower the battery cover.

Press and hold the start button. Pull the bail toward the

handle and release the button to start the mower.

To stop the mower, release the bail.

MOWING TIPS

Make sure the lawn is clear of stones, sticks, wires, and

other objects that could damage the lawn mower blades

or motor. Do not mow over property stakes or other metal

posts. Such objects could damage the blade or be acci-

dentally thrown by the mower in any direction and cause

serious personal injury to the operator and others.

For a healthy lawn, always cut off one-third or less of the

total length of the grass.

When cutting heavy grass, reduce walking speed to allow

for more effective cutting and a proper discharge of the

clippings.

Do not cut wet grass. It will stick to the underside of the

deck and prevent proper bagging or mulching of grass

clippings.

10 — English

OPERATION

New or thick grass may require a narrower cut or a higher

cutting height.

Clean the underside of the mower deck after each use

to remove grass clippings, leaves, dirt, and any other

accumulated debris.

NOTE: Always stop mower, allow blades to completely

stop, and remove the key before cleaning unerneath the

mower.

SLOPE OPERATION

See Figure 11.

WARNING:

Slopes are a major factor related to slip and fall accidents

that can result in severe injury. Operation on slopes

requires extra caution. If you feel uneasy on a slope, do

not mow it. For your safety, do not attempt to mow slopes

greater than 15 degrees.

Mow across the face of slopes, not up and down. Exercise

extreme caution when changing direction on slopes.

Watch for holes, ruts, rocks, hidden objects, or bumps

which can cause you to slip or trip. Tall grass can hide ob-

stacles. Remove all objects such as rocks, tree limbs, etc.,

which could be tripped over or thrown by the blade.

Always be sure of your footing. A slip and fall can cause

serious personal injury. If you feel you are losing your

balance, release the upper bail immediately.

Do not mow near drop-offs, ditches, or embankments;

you could lose your footing or balance.

EMPTYING THE GRASS CATCHER

See Figure 12.

 Stop the mower and allow blades to completely stop.

 Remove key and battery pack.

 Lift the rear discharge door.

 Lift the grass catcher by its handle to remove from mower.

 Empty grass clippings.

 Lift the rear discharge door and reinstall the grass catcher

as described earlier in this manual.

 Reinstall key and battery pack when you are ready to

mow.

WARNING:

Before performing any maintenance, make sure the

mower battery and key are removed to avoid accidental

starting and possible serious personal injury.

WARNING:

When servicing, use only authorized replacement parts.

Use of any other parts can create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

MAINTENANCE

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken, or

destroy plastic which can result in serious personal injury.

Periodically check all nuts and bolts for proper tightness to

ensure safe operation of the mower.

Remove any build-up of grass and leaves on or around the

motor cover. Wipe the mower clean with a dry cloth occa-

sionally. Do not use water.

11 — English

the mower deck and not down toward the ground. When

seated properly, the blade should be flat against the fan

assembly.

Replace the blade insulator and spacer, then thread the

blade nut on the shaft and finger tighten.

NOTE: Make certain all parts are replaced in the exact

order in which they were removed.

Torque the blade nut down clockwise using a torque

wrench (not provided) to ensure the bolt is properly

tightened. The recommended torque for the blade nut is

350-400 in. lbs.

STORING THE MOWER

See Figure 15.

Remove the battery and key and store in a secure location

out of the reach of children.

Before storage, wipe any dirt or debris from the battery

area.

Turn mower on its side and clean grass clippings that

have accumulated on the underside of the mower deck.

Wipe the mower clean with a dry cloth.

Check all nuts, bolts, knobs, screws, fasteners, etc., for

tightness.

Inspect moving parts for damage, breakage, and wear.

Have repairs made on any damaged or missing parts.

Check blade for damage, uneven, or excessive wear and

replace blade if these conditions exist.

Lower the handle assembly as described earlier in this

manual.

Store mower indoors in a clean, dry place out of the reach

of children.

Do not store near corrosive materials such as fertilizer or

rock salt.

MAINTENANCE

LUBRICATION

All of the bearings in this product are lubricated with a suf-

ficient amount of high grade lubricant for the life of the unit

under normal operating conditions. Therefore, no further

bearing lubrication is required.

WARNING:

Always protect hands by wearing heavy gloves and/or

wrapping the cutting edges of the blade with rags and

other material when performing blade maintenance. Con-

tact with the blade could result in serious personal injury.

REPLACING THE CUTTING BLADE

See Figures 13 - 14.

NOTE: Only use authorized replacement blades.

Stop the motor and remove the key. Allow blade to come

to a complete stop.

Remove the battery pack.

Turn the mower on its side.

Wedge a block of wood between the blade and mower

deck to prevent the blade from turning.

Loosen the blade nut by turning it counterclockwise (as

viewed from bottom of mower) using a 15 mm wrench

or socket (not provided).

Remove the blade nut, spacer, blade insulator, and blade.

Make certain the fan assembly is pushed completely

against the motor shaft.

Place the new blade on the shaft against the fan as-

sembly. Ensure blade is properly seated with shaft go-

ing through center blade hole and the two blade posts

inserted into their respective holes on the blade. Make

sure it is installed with the curved ends pointing up toward

12 — English

TROUBLESHOOTING

MAKE THE MOST OF YOUR PURCHASE!

Go to http://register.ryobitools.com and register your new tool on-line.

Your product has been fully tested prior to shipment

to ensure your complete satisfaction.

For any questions about operating or maintaining

your product, call the Ryobi® Help Line!

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

PROBLEM POSSIBLE CAUSE SOLUTION

Handle not in position Handle locks not locked. Lock upper and lower handle locks.

Mower not starting Battery is low in charge. Charge the battery.

Mower cutting grass unevenly Lawn is rough or cutting height not set

properly.

Adjust the cutting height.

Mower not mulching properly Wet grass clippings sticking to the un-

derside of the deck.

Wait until the grass dries before mow-

ing.

Mower hard to push High grass, rear of mower housing and

blade dragging in heavy grass, or cut-

ting height too low.

Raise cutting height.

Mower not bagging properly Cutting height set too low Raise cutting height.

Mower vibrating at higher speed Blade is unbalanced, excessively or

unevenly worn.

Bent motor shaft.

Replace the blade.

Stop the motor, remove key and battery.

Inspect for damage. Have repaired by

an authorized service center before

restarting.

Motor stops while cutting Cutting height set too low Raise the cutting height

13 — English

WARRANTY

LIMITED WARRANTY STATEMENT

Techtronic Industries North America, Inc., warrants to the

original retail purchaser that this RYOBI® brand outdoor

product is free from defect in material and workmanship

and agrees to repair or replace, at Techtronic Industries

North America, Inc.’s, discretion, any defective product

free of charge within these time periods from the date of

purchase.

 Three years if the product is used for personal, family

or household use;

 90 days, if used for any other purpose, such as

commercial or rental.

This warranty extends to the original retail purchaser

only and commences on the date of the original retail

purchase.

Any part of this product found in the reasonable judgment

of Techtronic Industries North America, Inc. to be defective

in material or workmanship will be repaired or replaced

without charge for parts and labor by an authorized service

center for RYOBI® brand outdoor products (Authorized

Ryobi Service Center).

The product, including any defective part, must be returned

to an authorized Ryobi service center within the warranty

period. The expense of delivering the product to the service

center for warranty work and the expense of returning it

back to the owner after repair or replacement will be paid

by the owner. Techtronic Industries North America, Inc.’s,

responsibility in respect to claims is limited to making the

required repairs or replacements and no claim of breach of

warranty shall be cause for cancellation or rescission of the

contract of sale of any RYOBI® brand outdoor product. Proof

of purchase will be required by the dealer to substantiate

any warranty claim. All warranty work must be performed

by an authorized service dealer.

This warranty is limited to ninety (90) days from the date

of original retail purchase for any RYOBI® brand outdoor

product that is used for rental or commercial purposes, or

any other income-producing purpose.

This warranty does not cover any product that has been

subject to misuse, neglect, negligence, or accident, or that

has been operated in any way contrary to the operating

instructions as specified in this operator’s manual. This

warranty does not apply to any damage to the product that

is the result of improper maintenance or to any product

that has been altered or modified. The warranty does not

extend to repairs made necessary by normal wear or by the

use of parts or accessories which are either incompatible

with the RYOBI® brand outdoor product or adversely affect

its operation, performance, or durability. In addition, this

warranty does not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive

Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,

Blower Fans, Blower and Vacuum Tubes, Vacuum Bag

and Straps, Guide Bars, Saw Chains

C. This warranty does not cover the battery for more than

three years from date of purchase.

Techtronic Industries North America, Inc., reserves the

right to change or improve the design of any RYOBI® brand

outdoor product without assuming any obligation to modify

any product previously manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE STATED WARRANTY PERIOD. ACCORDINGLY,

ANY SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, ARE DISCLAIMED

IN THEIR ENTIRETY AFTER THE EXPIRATION OF

THE APPROPRIATE THREE-YEAR OR NINETY-DAY

WARRANTY PERIOD. TECHTRONIC INDUSTRIES

NORTH AMERICA, INC.’S, OBLIGATION UNDER THIS

WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO

THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS

AND TECHTRONIC INDUSTRIES NORTH AMERICA,

INC., DOES NOT ASSUME OR AUTHORIZE ANYONE

TO ASSUME FOR THEM ANY OTHER OBLIGATION.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE

LIMITATION MAY NOT APPLY TO YOU. TECHTRONIC

INDUSTRIES NORTH AMERICA, INC., ASSUMES NO

RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,

OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED

TO, EXPENSE OF RETURNING THE PRODUCT TO AN

AUTHORIZED RYOBI SERVICE CENTER AND EXPENSE

OF DELIVERING IT BACK TO THE OWNER, MECHANIC’S

TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,

RENTAL OF A LIKE PRODUCT DURING THE TIME

WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,

LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS

OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS

OF TIME, OR INCONVENIENCE. SOME STATES DO NOT

ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This warranty applies to all RYOBI® brand outdoor products

manufactured by or for Techtronic Industries North America,

Inc., and sold in the United States and Canada.

To locate your nearest Authorized Ryobi Service Center,

dial 1-800-860-4050.

3 — Français

AVERTISSEMENT :

LISEZ ET VEILLEZ À COMPRENDRE TOUTES LES

INSTRUCTIONS. Le non respect des instructions

énumérées ci-dessous et sur la machine pourrait résulter

en un choc électrique, un incendie, et/ou des blessures

sérieuses.

LISEZ TOUTES LES INSTRUCTIONS

Cet outil coupant est capable d’amputer des mains et des

pieds et projeter des objets. Le non respect de toutes les

instructions de sécurité pourrait résulter en des blessures

graves ou la mort.

Éviter les environnements dangereux - N’utilisez pas la

tondeuse dans un environnement mouillé ou humide et ne

l’utilisez pas durant la pluie.

Garder les enfants à l’écart - Garder les badauds, enfants et

animaux domestiques à une distance minimum de 30,5 m

(100 pi). Arrêter la machine si quelqu’un entre dans la zone.

Des accidents tragiques peuvent survenir si l’opérateur n’est

pas conscient de la présence des enfants. Les enfants sont

souvent attirés pas la machine et l’activité de tondaison.

Ne prenez jamais pour acquis que les enfants resteront à

l’endroit où vous les avez vus la dernière fois.

• Assurez-vous que les enfants soient éloignés de la zone

de coupe et qu’ils soient supervisés par un adulte autre

que l’opérateur.

• Soyez vigilant et éteignez la tondeuse si un enfant

s’approche.

• Ne permettez jamais à des enfants d’utiliser la machine.

• Redoublez la prudence quand vous vous approchez des

coins, des arbustes, des arbres ou d’autres objets qui

peuvent masquer la présence d’un enfant.

Porter une tenue appropriée - Porter des pantalons longs,

manches longues, des chaussures de travail et des gants

épais. Ne pas porter de vêtements amples, bijoux, shorts,

sandales et ne pas travailler pieds nus. Ne porter aucun

bijou. Ils peuvent être pris dans les parties en mouvement.

Ne pas travailler hors de portée - Toujours se tenir bien

campé et en équilibre. Le travail hors de portée risque de

faire perdre l’équilibre.

N’utilisez pas l’outil pieds nus ou si vous portez des sandales

ou d’autres souliers légers de ce type. Portez des souliers de

protection qui protègeront vos pieds et amélioreront votre

équilibre sur des surfaces glissantes.

Ne laissez pas la tondeuse sans surveillance quand elle est

allumée ou une fois la clé fixée.

Éloignez les mains et les pieds de la zone de coupe. Tenez

vous éloigné de l’ouverture de décharge en tout temps.

Utilisez la tondeuse seulement à la lumière du jour ou avec

une bonne lumière artificielle.

Portez toujours des lunettes de sécurité avec des écrans

latéraux. Des lunettes de tous les jours résistent seulement

aux chocs. Ce ne sont PAS des lunettes de sécurité.

Le respect de cet avertissement réduira le risque d’une

blessure à l’oeil. Utilisez un masque facial si la tâche est

poussiéreuse.

Porter des lunettes de sécurité - Toujours porter une

protection oculaire avec écrans latéraux certifiée conforme à

la norme ANSI Z87.1.Porter un masque facial ou un masque

anti-poussière si le travail produit de la poussière.

Utilisez l’outil approprié - N’utilisez pas la tondeuse pour

aucune tâche sauf celle pour laquelle elle est conçue.

Ne forcez pas la tondeuse - Elle exécutera le travail mieux

et de façon plus sécuritaire à la vitesse pour laquelle elle fut

conçue.

Restez vigilant - Regardez ce que vous faites et utilisez

votre meilleur jugement lorsque vous utilisez la tondeuse.

N’utilisez pas la tondeuse si vous êtes fatigué, contrarié ou

sous influence de drogues, d’alcool ou de médicaments. Un

moment d’inattention pendant l’utilisation de la tondeuse

peut résulter en une blessure grave.

Faire l’entretien de la tondeuse avec soins - Gardez l’outil

en bon état. Assurez-vous que les lames soient affûtées et

que les dispositifs de protections soient en place et en état

de fonctionnement. Remplacer les lames endommagées ou

usées de façon inégale avant d’utiliser la tondeuse d’obtenir

un rendement optimal.

Vérifiez fréquemment si tous les écrous, boulons et vis sont

serrés pour s’assurer que l’équipement est sécuritaire. Les

lames de tondeuse sont tranchantes. Envelopper la lame ou

porter des gants et prendre beaucoup de précautions lors

de l’entretien.

Ne pas jeter le pile au feu. La cellule peut exploser. Vérifier

les codes locaux pour connaître toute instruction spéciale

relative à l’élimination des piles.

Arrêter le moteur, attendre que la lame s’arrête complètement

et retirer la clé et bloc-piles avant de nettoyer la tondeuse,

d’enlever le collecteur d’herbe ou retrait du capuchon du

broyeur.

Remplacer la lame si elle est pliée ou fissurée. Une

lame déséquilibrée provoque des vibrations qui peuvent

endommager le moteur de l’appareil et provoquer

des blessures. Affûter également les extrémités de la

lame émoussée afin de maintenir l’équilibre. Nettoyer

complètement la lame et vérifier son équilibre en la déposant

à l’horizontale et en plaçant l’orifice du centre sur un petit

clou. Le clou doit être placé à l’horizontale. Si l’une des

extrémistes de la lame tourne vers le bas, enlever un peu de

métal de la partie épaisse inférieure de la lame jusqu’à ce que

celle-ci soit équilibrée. Une lame équilibrée lorsqu’aucune

extrémité n’est inclinée.

Quand la tondeuse n’est pas utilisée, elle devrait être

entreposée à l’intérieur, dans un endroit sec et sécuritaire -

loin de la portée des enfants. Retirer la clé et la ranger dans

un endroit situé hors de la portée des enfants.

Toujours, utiliser des dispositifs de protection. N’utilisez

pas la tondeuse sans le collecteur d’herbe, le capuchon du

broyeur et porte arrière de décharge en place et fonctionne

correctement.

Ne pas ouvrir ou altérer le bloc de batteries. L’électrolyte est

un produit corrosif pouvant causer des lésions cutanées ou

oculaires. Il peut être toxique en cas d’ingestion.

Suivez les instructions du fabricant relatives à l’installation

et l’utilisation des accessoires. Utilisez seulement des

accessoires approuvés par le fabricant.

Manipuler les batteries avec soin pour éviter des courts-

circuits avec des objets conducteurs comme des anneaux,

des bracelets et des clés. La batterie ou l’objet conducteur

peuvent surchauffer et causer des brûlures.

INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ

4 — Français

INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ

Nettoyez la zone de travail avant chaque utilisation. Enlevez

tous les objets tels que les roches, les branches, métal, les

fils, les os, les jouets et d’autres objets qui peuvent être

projetés par la lame. Restez en arrière de la poignée quand

le moteur est en marche.

Évitez les trous, les ornières, les roches, bornes de propriété

ou d’autres objets cachés. Un terrain accidenté pourrait

provoquer un glissement et vous faire tomber par accident.

Ne tondez pas près des dépressions, fossés ou des berges.

Tondez les pentes dans le sens transversal, jamais en

montant ou en descendant. Soyez particulièrement prudent

lors des changements de direction sur les terrains en pente.

Planifiez le parcours de la tondeuse pour éviter d’éjecter

les matériaux sur les routes, les trottoirs, les passants, etc.

Évitez également d’éjecter les matériaux sur un mur ou une

obstruction ce qui pourrait causer un matériau d’être projeté

par ricochet en direction de l’opérateur.

Ne tondez pas l’herbe mouillée ou sur des pentes

excessivement raides. Une mauvaise position peut vous faire

glisser et tomber par accident. Marchez, ne courez jamais.

Redoublez la prudence si vous vous approchez des coins,

des arbustes, des arbres ou d’autres objets qui vous cachent

la vue.

Ne tirez jamais la tondeuse vers l’arrière à moins que cela

soit absolument nécessaire. Si vous devez tirer la tondeuse

pour éviter un mur ou une obstruction, commencez par

regarder en bas et en arrière pour ne pas trébucher o tirando

la podadora hacia los pies.

N’éjectez jamais du matériel en direction de quelqu’un.

Évitez d’éjecter le matériel sur un mur ou une obstruction.

Le matériel pourrait être projeté par ricochet en direction

de l’opérateur. Arrêtez la lame quand vous traversez des

surfaces recouvertes de gravier.

Des objets frappés par la lame de la tondeuse peuvent

causer des sérieuses blessures. La pelouse devrait toujours

être examinée attentivement et nettoyée de tout objet avant

la tondaison.

Si la tondeuse frappe un objet étranger, suivez ces étapes:

•

Arrêter la tondeuse en relachant l’anse, attendre que la lame

s’arrête complètement, puis retirer la clé.

• Arrêtez la tondeuse et relâchez le levier de commande.

• Remplacer la lame si elle est endommagée de quelque

façon que ce soit Réparez tout dommage avant de démar-

rer et de continuer à utiliser la tondeuse.

Arrêter le moteur, attendre que la lame s’arrête complètement

et retirer la clé avant de déboucher la goulotte. La lame

continue de tourner pendant quelques secondes après que

le moteur soit arrêté. Ne mettez jamais aucune partie du

corps dans la proximité de la lame avant d’être certain que

la lame a cessé de tourner.

Si la tondeuse commence à vibrer de façon anormale, arrêtez

le moteur et vérifiez immédiatement la cause. Remplacer la

lame si elle est usée de façon inégale ou endommagée de

quelque façon que ce soit. La vibration est généralement un

signe d’un problème.

Le produit doit être réparé par un personnel qualifié

seulement. Des réparations ou l’entretien effectués par un

personnel non qualifié pourrait résulter en des blessures

pour l’utilisateur ou endommager le produit.

Lors de réparation du produit, utilisez pièces de remplacement

autorisées. Utiliser uniquement des lames de rechange

identiques. L’utilisation des pièces non autorisées peut

créer un risque d’une blessure sérieuse à l’utilisateur ou

endommager le produit.

Conserver ou remplacer les étiquettes d’instructions de

sécurité, si nécessaire.

Déconnecter le bloc-piles – Débrancher l’appareil de la source

d’alimentation avant d’entreposer, d’effectuer l’entretien,

transport, ou de changer les accessoires comme la lame.

Ces mesures de sécurité réduisent les risques de démarrage

accidental de l’outil.

Arrêter l’produit et retirer le bloc de piles et clé lorsqu’il n’est

pas utilisé. Attendre ou mettre l’arrêt complet du moteur et la

clé et le bloc-piles retirés de la tondeuse avant de déplacer

l’produit.

Les outils fonctionnant sur batteries n’ayant pas besoin

d’être branchés sur une prise secteur, ils sont toujours en

état de fonctionnement. Tenir compte des dangers possibles

lorsque l’outil n’est pas en usage et lors du remplacement

des batteries. Le respect de cette règle réduira les risques

d’incendie, de choc électrique et de blessures graves.

 Ne pas utiliser un appareil alimenté par batterie sous la pluie.

 Retirer ou débrancher la batterie avant l’entretien ou le net-

toyage de l’outil de jardin ou avant d’en retirer des matériaux.



Ne recharger qu’avec l’appareil indiqué. Pour utiliser l’appareil

avec des piles au lithium-ion de 40 V, consulter le supplément

de raccordement pour chargeur/outils/piles/appareil n˚ 988000-

842.

 Ranger les appareils qui ne sont pas utilisés à l’intérieur –

lorsque la tondeuse n’est pas utilisé, le ranger à l’intérieur

dans un endroit sec et verrouillé hors de la portée des enfants.



Suivre les instructions de lubrification et de changement

d’accessoires.



Maintenir les dispositifs de protection en place et en bon état

de fonctionnement.



Garder les lames affûtées.



Éloigner les mains et les pieds de la zone de coupe.



Faire fonctionner cet appareil ne doit être permis qu’aux adultes

responsables et familiers avec les instructions.



Ne jamais faire fonctionner l’appareil dans un endroit clos.



Ne jamais modifier les dispositifs de sécurité. Vérifier

périodiquement l’état de fonctionnement.



Conserver ces instructions. Les consulter fréquemment et les

utiliser pour instruire les autres utilisateurs éventuels. Si cet

outil est prêté, il doit être accompagné de ces instructions.

5 — Français

Certains des symboles ci-dessous peuvent être utilisés sur produit. Veiller à les étudier et à apprendre leur signification.

Une interprétation correcte de ces symboles permettra d’utiliser produit plus efficacement et de réduire les risques.

SYMBOLE NOM DÉSIGNATION / EXPLICATION

Symbole d’alerte de sécurité Indique un risque de blessure potentiel.

Lire manuel d’utilisation Pour réduire les risques de blessures, l’utilisateur doit lire et veiller à

bien comprendre le manuel d’utilisation avant d’utiliser ce produit.

Protection oculaire Toujours porter une protection oculaire avec écrans latéraux

certifiée conforme à la norme ANSI Z87.1.

Avertissement concernant

l’humidité Ne pas exposer à la pluie ou l’humidité.

Choc électrique Ne pas utiliser la machine dans un endroit sec ou ne pas respecter

les pratiques de sécurité peut entraîner un choc électrique.

Garder les mains et les pieds

à l’écart

Garder les mains et les pieds à l’écart de la lame et de la zone

de coupe.

Se tenir loin Ne pas mettre ses mains ou ses pieds en dessous du châssis

de la tondeuse.

Éviter les pentes Ne pas utiliser sur des pentes de plus de 15°. Tondre les pentes

dans le sens transversal, jamais en montant ou en descendant.

Tenir les enfants et les cu-

rieux à bonne distance

Tenir les enfants et les curieux à une distance de 30,5 m (100 pi)

au moins.

SYMBOLES

Les termes de mise en garde suivants et leur signification ont pour but d’expliquer le degré de risques associé à l’utilisation

de ce produit.

SYMBOLE SIGNAL SIGNIFICATION

DANGER : Indique une situation extrêmement dangereuse qui, si elle n’est pas évitée,

aura pour conséquences des blessures graves ou mortelles.

AVERTISSEMENT : Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée,

pourrait entraîner des blessures graves ou mortelles.

ATTENTION : Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée,

pourraît entraîner des blessures légères ou de gravité modérée.

AVIS :

(Sans symbole d’alerte de sécurité) Indique une information importante

ne concernant pas un risque de blessure comme une situation pouvant

occasionner des dommages matériels.

La page est en cours de chargement...

Ryobi RY401200 Le manuel du propriétaire

Marque: Ryobi

Modèle: RY401200

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi RY401200 Owner's manual
español: Ryobi RY401200 El manual del propietario

Ryobi RY401200 Le manuel du propriétaire

Ryobi RY401200 Le manuel du propriétaire

dans d''autres langues

Documents connexes