YoLink YS3606-UC DimmerFob Dimmer Switch Mode d'emploi
- Taper
- Mode d'emploi
In the Box
C
Quick Start Guide
YS3606-UC
DimmerFob
Revision Jan. 03, 2023
Before You Begin
B
Installation & User
Guide
Product Support
Support produit
Soporte de producto
Your DimmerFob connects to the
internet via a YoLink hub (SpeakerHub or
the original YoLink Hub), and it does not
connect directly to your WiFi or local
network. In order for remote access to
the device from the app, and for full
functionality, a hub is required. This
guide assumes the YoLink app has been
installed on your smartphone, and a
YoLink hub is installed and online (or
your location, apartment, condo,
etcetera, is already served by a YoLink
wireless network).
You can also find all guides and
additional resources, such as videos and
troubleshooting instructions, on the
DimmerFob Product Support page by
scanning the QR code below or by
visiting:
https://shop.yosmart.com/
pages/dimmerfob-product-support
Please note: this is a quick start guide,
intended to get you started on the
installation of your DimmerFob.
Download the full Installation & User
Guide by scanning this QR code:
LED & Beep Behaviors
Blinking Red Once, Then Green
Once
Device Power Up
Blinking Red And Green Alternately
Restoring to Factory Defaults
Blinking Green Once
One Beep
On or Brightness Increase/
Decrease Button Pressed
Blinking Red Once
Two Beeps
Dimmer Off Button Pressed
Blinking Green Twice
Connecting to Cloud
Quick Blinking Green
Control-D2D Pairing in Progress
Quick Blinking Red
Control-D2D Unpairing in Progress
Slow Blinking Green
Updating
Fast Blinking Red Every 30 Seconds
Batteries are Low, Please Replace
the Batteries
Welcome!
A
Thank you for purchasing YoLink
products! We appreciate you trusting
YoLink for your smart home & automa-
tion needs. Your 100% satisfaction is our
goal. If you experience any problems
with your installation, with our products
or if you have any questions that this
manual does not answer, please contact
us right away. See the Contact Us
section for more info.
Thank you!
Eric Vanzo
Customer Experience Manager
Pour des instructions en
français, scannez les codes
QR dans la section suivante.
Para obtener instrucciones en
español, escanee los códigos
QR en la siguiente sección.
Fr
Es
User Guide Conventions
The following icons are used in this guide to
convey specific types of information:
Very important information
(can save you time!)
Battery
Compartment Screw
Compartment houses
two AAA batteries
Get to Know Your
DimmerFob
D
DimmerFob
Quick Start Guide
AAA Batteries (2)
Installed
Status LED
LED is off when the
fob is in a normal
status
Four Buttons
Key Ring Slot
Attach the fob to a
key ring, if desired
Power Up
E
Open the app and tap Sign up for an
account. You will be required to provide
a username and a password. Follow the
instructions, to set up a new account.
Allow notifications, when prompted.
You will immediately receive a welcome
email from [email protected] with
some helpful information. Please mark
the yosmart.com domain as safe, to
ensure you receive important messages
in the future.
Log in to the app using your new
username and password.
The app opens to the Favorite screen.
This is where your favorite devices and
scenes will be shown. You can organize
your devices by room, in the Rooms
screen, later.
Refer to the full user guide and online
support for instructions on the use of the
YoLink app.
Install the App
F
If you are new to YoLink, please install
the app on your phone or tablet, if you
have not already. Otherwise, please
proceed to the next section
Scan the appropriate QR code below or
find the “YoLink app” on the appropriate
app store.
Add the DimmerFob to
the App
G
2. Approve access to your phone’s
camera, if requested. A viewfinder will be
shown on the app.
3. Hold the phone over the QR code so
that the code appears in the viewfinder.
If successful, the Add Device screen will
be displayed.
4. You can change the device name and
assign it to a room later. Tap Bind
device.
5. If successful, the screen will appear as
shown. Tap Done.
Contact Us
H
We are here for you, if you ever need any
assistance installing, setting up or using
a YoLink app or product!
Need help? For fastest service, please
email us 24/7 at [email protected]
Or call us at 831-292-4831 (US phone
support hours: Monday - Friday, 9AM to
5PM Pacific)
You can also find additional support and
ways to contact us at:
www.yosmart.com/support-and-service
Or scan the QR code:
Finally, if you have any feedback or
suggestions for us, please email us at
Thank you for trusting YoLink!
Eric Vanzo
Customer Experience Manager
Support
Home Page
15375 Barranca Parkway
Ste. J-107 | Irvine, California 92618
© 2022 YOSMART, INC IRVINE,
CALIFORNIA
1. Tap Add Device (if shown) or tap the
scanner icon:
Apple phone/tablet
iOS 9.0 or higher
Android phone/
tablet 4.4 or higher
Scanner icon
Press any button
on your fob briefly.
Observe the LED
blinks red then
green.
-
1
-
2
