Lifetime 90602 Le manuel du propriétaire

TOOLS REQUIRED TABLE OF CONTENTS

(x2) (x2) (x2) (x2) (x2)

(x1) (x1)

1/2" (≈13 mm) 9/16" (≈14 mm) 11/16" (≈18 mm) 3/4" (≈19 mm) 1/2" (≈13 mm) Icon Legend................................2

Warnings & Notices.....................3

Ground Preparation.....................4

Pole Assembly.............................9

Backboard-to-Rim Assembly......12

Backboard-to-Pole Assembly.......17

Parts Identiﬁ er..........................i-iv

Handle Assembly......................24

Final Assembly..........................32

Maintenance.........................37

Warning Sticker........................38

Registration........................42

Warranty................................43

(x1) (x1)

Concrete Mix

640 lb (291 kg)

Level

(x1)

1/2" (≈13 mm)

(x1)

(x1) (x3)

(x1)

CONTACT LIFETIME CUSTOMER SERVICE:

Dial 1-800-225-3865

7:00 am–5:00 pm (M–F) MST

and 9:00 am–1:00 pm (Sat) MST

QUESTIONS? Model Number: 90602

Product ID:

For Customer Service in Mainland

Europe and the United Kingdom,

E-mail: [email protected]

Live Chat:

www.lifetime.com/customerservice

PUMP ADJUST®

BASKETBALL SYSTEM

BEFORE ASSEMBLY:

• Requires 640 lb (291 kg) of concrete mix.

• Requires at least 72 hours (3 days) for concrete to cure, plus 3–4

hours to complete assembly steps.

• At least three (3) adults required for setup.

ASSEMBLY INSTRUCTIONS

MODEL 90602

Save this instruction in the event that the manufacturer must be contacted for replacement parts.

(≈4-6)

Bricks

3D ANIMATION

OF THE FULL ASSEMBLY

WATCH

SCAN THE

CODE

OR SEARCH

1184987,

1210184

2

• Indicates the parts to be used for a section.

• Indicates special heed should be taken when reading.

• Indicates the hardware to be used for a section.

• Indicates the tools to be used for a section.

• Indicates no hardware required for a speciﬁ c page.

• Indicates no parts required for a speciﬁ c section.

• Indicates to use/not to use an electric drill for a speciﬁ c step.

ICON LEGEND

• Indicates the use of a centerlock nut. A nut with this marking will require some effort to tighten.

This hardware was designed with this feature in order to prevent loosening later.

1220859 9/25/2021

3

WARNINGS & NOTICES

Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.

To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing

material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware

identiﬁ er and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operation and to reduce the

risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.

Owner must ensure that all players know and follow these rules for safe operation of the system.

• If using a ladder during assembly, use extreme caution.

• Three capable adults are recommended for this operation.

• Assemble the pole sections properly. Failure to do so could cause the pole sections to separate during play or transport.

• Before digging, contact utility company to locate underground power cables, gas, and water lines. Ensure that there are no

overhead power lines within 20' (7 m) radius of pole locations.

• Minimum operational height is 6'-6" (1.98 m) to the bottom of the backboard.

SAFETY INSTRUCTIONS

SAFE HANDLING OF THE GLASS BACKBOARD

BEFORE & DURING ASSEMBLY

1. Thoroughly inspect the backboard before beginning assembly. Do not use the backboard if there are any chips,

cracks, or other defects in the board. Call our customer service department if any problems are found.

2. Use extreme caution when handling or working around the backboard.

3. Keep tools, hardware, and other sharp and heavy objects away from the backboard.

4. Never rest the backboard directly on a hard surface, such as concrete or pavement. Always place cardboard or

other cushioning material between the backboard and the ground or other hard surfaces.

5. Always lay the backboard ﬂ at. Never place it in a position where it might tip over and break.

6. Glass is very heavy. Always use at least two adults when picking up or moving the backboard.

General Handling & Care

1. Inspect the backboard before each use. Do not use the backboard if there are any chips, cracks, or other defects in

the board. If any signs of damage are found, follow the instructions for “handling broken glass” below.

2. Use extreme caution when handling or working around the backboard.

3. The backboard was designed for use with a basketball. Do not use other types of balls or other objects with the

system. Do not use this system for any purpose other than its designed purpose.

Handling Broken Glass

At the ﬁ rst sign of breakage:

1. Keep everyone, especially children, away from the immediate area of the backboard.

2. Put on eye protection, and wear thick utility gloves and long sleeves. Small pieces of tempered glass may pop out of

the backboard.

3. Lower the backboard to its lowest height, and completely cover the backboard with a tarp.

4. Do not remove the backboard from the system without ﬁ rst lowering the system to its lowest setting. Carefully read

and follow the “removing backboard from system” instructions below.

Removing Backboard from System

1. With the backboard at its lowest height, have at least two capable adults support the system while one adult

removes the hardware securing the pole to the playing surface.

2. Have at least three capable adults carefully lay the system down. Make sure to rest the rim on a sheet of cardboard

or other non-abraisive surface.

3. Loosen and remove the hardware from the steps performed in the backboard to pole assembly section of this

manual in reverse order. Keep the hardware.

4. Loosen and remove the hardware from the steps performed inthe backboard to rim assembly section to safely

remove the rim. Keep all parts and hardware from this section for reassembly.

4

1

Metal parts

Hardware bag

TOOLS REQUIRED

PARTS REQUIRED

HARDWARE REQUIRED

(x1)

ALE (x1)

BGW (x1)

Plastic parts

(x1)

Concrete mix

640 lb (291 kg)

INITIAL SET UP

(≈4-6)

5

TOOLS AND HARDWARE REQUIRED

 SECTION 1 (CONTINUED)

1.1 • Dig a round hole 24” (≈61 cm) deep and 21” (≈53 cm) in diameter. If you live in an area where frost heaves may

pose a problem, consult your local building inspector to determine the proper hole depth. The edge of the hole

should be ﬂ ush with the edge of the playing surface.

24 in/po

21 in/po

• Widen the bottom diameter about 4” (≈10 cm)

into a bell-shaped hole as shown.

1.2

ALE

16 in/po

(40.6 cm)

• Make a mark 16 inches (40.6 cm) from the

dimpled end of the Bottom Pole (ALE) (do not

scratch the powder coating).

1.3

6

TOOLS AND HARDWARE REQUIRED

 SECTION 1 (CONTINUED)

• Stack bricks in the hole for the bottom pole to stand on. Stack enough bricks

in the hole so that the 16-inch (40.6 cm) mark on the pole is even with

the top edge of the playing surface. If the pole is not even with the playing

surface, dig the hole deeper or add more bricks as necessary. Position the

bricks close to the front edge of the hole, near the playing surface. The correct

distance from the basketball court to the front of the pole is 4” (≈10 cm).

1.4

640 lb (291 kg)

• A ground sleeve is available as an

alternative to cementing the pole into the

ground. Please contact Customer Service

for more information.

!

Playing surface

Bricks

16 in. mark

• Mix the concrete. Have one adult hold the bottom pole in place

on the bricks, then pour the mixed concrete into the hole until it is

ﬁ lled to the level of the playing surface.

1.5

Playing surface

4 in/po

• IMPORTANT! If the pole is buried too deep

or too shallow, the rim will not to be at the

correct height.

!

7

TOOLS AND HARDWARE REQUIRED

 SECTION 1 (CONTINUED)

• Slide the paper Alignment Frame (BGW) over the bottom pole. For regulation courts, the alignment frame should

cross the playing surface at the middle of the scored measurements.

1.7

• IMPORTANT! If the pole is buried too deep

or too shallow, the rim will not to be at the

correct height.

!

Playing Surface

ALE

TOP VIEW

BGW

• Use a level to make sure the bottom pole is standing vertical. Form the cement into a downward slope away from

the pole to allow water runoff. Failure to do so may result in premature rusting of the pole.

1.6

(x1)

Slope

8

TOOLS AND HARDWARE REQUIRED

 SECTION 1 (CONTINUED)

!

• Check the pole several times within the ﬁ rst hour to make sure that all sides are vertical and that the 16-inch

mark (40.6 cm) remains level with the surface.

1.8

• STOP ASSEMBLY NOW!

Do not continue the assembly until the concrete has been allowed to set for at least 72 hours (3 days). In humid climates or wet

weather, allow more time for the concrete to cure. Do not proceed until the curing process is complete.

• You may now remove the

alignment frame (BGW).

(x1)

BGW

9

POLE ASSEMBLY

2

BCO

Metal Parts

Hardware Bag

TOOLS REQUIRED

PARTS REQUIRED

HARDWARE REQUIRED

(1)

9/16" (≈15 mm)

(1) (2)

• Warning Sticker applied to this Pole

CMV (x2)*

AAA (x2) AAF (x2)

ANF (x2)

ANE (x2)

5”

• Only one Self-Drilling Screw (CMV) will

be used in Section 2. Save the second

Screw for use in Section 5.

ALL (x1)

!

ALF (x1)

ALH (x1)

10

TOOLS AND HARDWARE REQUIRED

 SECTION 2 (CONTINUED)

• Secure the Pole Bracket (ALL) to Top Pole (ALH)

with the hardware shown.

2.1

ANE (x2)

ANF (x2)

ALH

ANF

ANE ALL

AAA

AAF

Large Holes

Small Holes

AAA (x2)

9/16” (≈15 mm)

(2)

5”

AAF (x2)

ALH

ALF

• Slide the Top Pole over the Middle Pole (ALF). Make

sure the Warning Sticker is on the opposite side of

the assembly as the Pole Bracket.

2.2

FAUTE DE NE PAS SUIVRE CES AVERTISSEMENTS, VOUS RISQUEZ DE CAUSER

DES BLESSURES GRAVES ET/OU DES DOMMAGES À L’ÉQUIPEMENT.

Le propriétaire doit s’assurer que tous les joueurs con-

naissent et appliquent les règles suivantes aﬁn d’utiliser

l’équipement en toute sécurité.

SI NO SE OBEDECEN ESTAS ADVERTENCIAS PUEDEN PRODUCIRSE

GRAVES LESIONES Y/O DAÑOS A LA PROPIEDAD.

El propietario del sistema debe asegurarse de que todos

los jugadores conozcan y respeten estas reglas para que el

sistema se use en forma segura.

WARNING

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

Owners must ensure that all players know and follow these

rules for safe operation of the system.

• Only hang from the Rim brieﬂy to regain balance or avoid

injuring others. Release the Rim as soon as safely possible.

• During play, especially when performing dunk type activities,

keep player’s face away from the Backboard, Rim, and Net.

Serious injury could occur if teeth/face come in contact with

the Backboard, Rim, or Net. Player should wear a mouth

guard during play.

• Do not slide, climb, or play on Base or Pole.

• When adjusting height or moving system, keep hands and

ﬁngers away from moving parts.

• Do not allow children to move or adjust system.

• Do not wear jewelry (rings, watches, necklaces, etc.) during

play. Objects may entangle in Net.

• Keep water and organic material away from Pole Base. Grass,

litter, etc. could cause corrosion and/or deterioration.

• Never play on damaged equipment.

• Once a month check Pole and all metal parts for signs of

corrosion (rust, pitting, chipping). Completely remove rust and

repaint with exterior enamel. If rust has penetrated any steel

part, replace that part immediately.

• Check system before each use for proper ballast, loose

hardware, excessive wear, instability, and signs of corrosion

and repair before use.

• Do not use the system to lift or hoist anything. The

mechanism is designed to lift only the weight of the

Backboard and Rim. Do not hang anything from the Handle,

Rim, Backboard, or Lifter Arms as this will damage the

system and void the warranty.

• Ne vous suspendez pas à l’anneau plus que nécessaire pour

retrouver votre équilibre ou éviter de blesser les autres joueurs.

Relâchez l’anneau aussitôt que possible.

• Lors d’un match, particulièrement dans le cas des smashs, le

visage du joueur ne doit pas faire face au panneau, à l’anneau, ni au

ﬁlet. Le joueur risque de graves blessures si ses dents ou son visage

entrent en contact avec le panneau, l’anneau, ou le ﬁlet. Les joueurs

doivent toujours porter un protège-dents lorsqu’ils jouent.

• Ne glissez pas, ne grimpez pas, et ne jouez pas sur la base ou le

poteau.

• Lorsque vous ajustez la hauteur ou lorsque vous déplacez

l’équipement, gardez vos mains et doigts loin des pièces mobiles.

• Ne permettez pas aux enfants de déplacer ou d’ajuster

l’équipement.

• Ne portez pas de bijoux (bagues, montres, colliers, etc.) lorsque

vous jouez. Ces objets pourraient s’accrocher au ﬁlet.

•Gardez de l’eau et de la matiére organique loin de la base. Le

gazon, les déchets, etc. pourraient provoquer la corrosion et/ou la

détérioration.

• Une fois par mois, vériﬁez que le Poteau et toutes les pièces en

métal ne montrent pas de signes de corrosion (rouille, piqûres,

écaillage). Enlevez toute la rouille et repeignez complètement avec

une peinture pour extérieur. Si la rouille a pénétré une des pièces en

acier, vous devrez remplacer immédiatement la pièce en question.

• A chaque fois que vous allez utiliser l’équipement, vériﬁez d’abord

l’équilibre, la possibilité de pièces desserrées ou usées, la stabilité

de l’équipement et tout signe de corrosion ou réparation nécessaire

avant utilisation.

• Ne jouez jamais avec un équipement endommagé.

• N’utilisez pas l’équipement pour lever ou soulever quoique ce soit.

Son mécanisme a été conçu uniquement pour soutenir le poids du

panneau et de l’anneau. N’accrochez rien au manche, à l’anneau,

au panneau ni aux leviers sous peine d’endommager l’équipement

et d’annuler la garantie.

• Cuélguese del aro sólo en forma breve, para recuperar el equilibrio

o evitar lesionar a otros jugadores. Suéltese del aro lo más pro nto

que pueda hacerlo con seguridad.

• Durante el juego, e specialmente al embocar violentamente de

alto, la cara de los jugadores debe mantenerse alejada del tablero,

el aro y la red. Pueden producirse lesiones graves si los dientes o la

cara entran en contacto con el tablero, el aro o la red. Los jugadores

deben usar un protector bucal durante el juego.

• No se deslice, no trepe ni juegue sobre la base o el poste.

•Mantenga las manos y los dedos alejados de las piezas movibles

cuando regule la altura o desplace el sistema.

• No deje que los niños regulen ni desplacen el sistema.

• No use joyas (anillos, relojes, collares o gargantillas, etc.) durante el

juego. Estos objetos pueden engancharse en la red.

• Guarde aqua y materia orgánica. Céspe d, basura,etc., prodrian

causar corrosión et/o deterioros.

• Co ntrole el poste y todas las piezas metálicas una vez al mes

en busca de signos visibles de corrosión (oxidación, picaduras,

escamado). Elimine todo rastro de óxido y vuelva a pintar con

esmalte para exteriores. Si el óxido ha penetrado cualquier pieza de

acero, reemplace esa pieza de inmediato.

• Inspeccione el sistema antes de cada uso para veriﬁcar que esté

adecuadamente contrapesado, que los elementos de ﬁjación no

estén ﬂojos, que no haya desgaste excesivo, inest abilidad ni signos

de corrosión. Si encuentra irregularidades, repárelas antes de usar

el sistema.

• Nunca juegue con un equipo dañado.

•No use el sistema para levantar ningún objeto. El mecanismo está

diseñado para elevar solamente el peso del tablero con el aro. No

cuelgue nada de la agarradera, el aro, el tablero ni los brazos de

elevación, ya que esto puede dañar el sistema y anular la garantía.

www.lifetime.com # 1176611

ADVERTENCIAAVERTISSEMENT

Lifetime Products, Inc., Clearﬁeld, UT 84016

1-800-225-3865 7/12/2016

11

TOOLS AND HARDWARE REQUIRED

 SECTION 2 (CONTINUED)

2.3

• Do not hit your feet with the Pole

sections, as serious injury could

occur.

(1)

• THIS STEP CANNOT BE REVERSED! Strike the end of the Pole Assembly on a piece of scrap wood or

cardboard ﬁ ve to six times.

6x

!

(1)

CMV (x1)

CMV

ALH

ALF

1" up from bottom of

Top Pole

• After the Poles have been seated, measure up 1" from the bottom center of the Top Pole (ALH) and insert one

Self-Drilling Screw (CMV) into the Pole as shown.

2.4

WARNING

The Poles must be seated together! Poles must

be struck on a hard surface ﬁve to six times!

Failure to seat the Poles correctly could allow the

Poles to separate during use, which could lead

to serious personal injuries or property damage.

12

BACKBOARD TO RIM ASSEMBLY

3

BCS

Hardware Bag

PARTS REQUIRED

HARDWARE REQUIRED

AJI (x1)

Metal Parts

ANK (x4)

ABK (x4)

ADX (x2) BGZ (x1)

ANL (x1)

5 9/16”

AAX (x1) ANO (x1) ABD (x4)

ANM (x2)

ABB (x2)

ANN (x2) ANJ (x4)

AMB (x1)

AMA (x1)

BGY (x1)

AMC (x1)

AMK (x1)

ALY (x1)

BPZ (x1)

BQA (x1)

ALX (x1)

TOOLS REQUIRED

1/2" (13 mm) 9/16" (14 mm) 3/4" (19 mm)

(x1) (x2) (x2) (x2)

13

 SECTION 3 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

ANJ (x2)

ABD (x2) ABK (x2)

3.1

• The Glass Backboard will break if the Rim

Spacer (BGY) is not installed as shown in this

step. This may result in personal injury or

property damage.

!ANJ

ANJ

ABD

AMB

AMC

BGY

AJI

ABK

• Lay the Backboard (AJI) face up with the Rim holes exposed over the edge of a table. Place the Rim Impact Spacer

(BGY) in the Backboard. Add the Left and Right Rim Housings (AMC & AMB) on top of the Rim Impact Spacer and slide

the hardware shown into place.

9/16" (14 mm)

(x2)

14

 SECTION 3 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

3.2

3.3

• Secure the Rim Adapter Plate (ALY) to the Backboard (AJI) by using the hardware as shown.

• Slide the end of the Rim Pin (BPZ) into the Rim (ALX) and through the Eye Bolt (BQA) in the location indicated. Attach

the Rim to the Rim Housing using the hardware shown, making sure the Nylon Washers (ANK) rest between the Rim

and the Rim Housing.

ANJ (x2)

ABD (x2)

ABK (x2)

ABD

ANJ ANJ

ALY

ABK

AJI

BPZ BQA

ALX

ANK

ANL

AAX

5 9/16”

ANL (x1) AAX (x1)

ANK (x2)

1/2" (13 mm)

(x2)

3/4" (19 mm)

(x2)

15

 SECTION 3 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

ANM (x2) ABB (x2)

ALX

BQA

AMK

ANK (x2)

ANM

ABB

3.4 • Slide the Spring Holder Clevis (AMK) onto the Eye Bolt (BQA) and secure with the hardware shown.

ANK

9/16" (14 mm)

(x2)

16

 SECTION 3 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

3.5

3.6

• Slide the Compression Spring (BGZ) onto the Eye Bolt (BQA), and secure with the hardware shown. Tighten the 3/8” Zinc

Nuts (ANN) to adjust Rim tension.

• Attach the Rim Cover Plate (AMA) to the Rim with the hardware shown.

BQA

ANN

ANN (x2)

ANO

BGZ (x1)

ANO (x1)

BGZ

ADX (x2)

AMA

ADX

(x1)

9/16" (14 mm)

(x2)

17

Metal Parts

Hardware Bag

TOOLS REQUIRED

PARTS REQUIRED

HARDWARE REQUIRED

BACKBOARD TO POLE ASSEMBLY

4

(x1) (x2) (x1) (x1)

1/2" (≈13 mm) 1/2" (≈13 mm)

3/4" (≈19 mm) 11/16" (≈18 mm)

(x1)

BCR

AAD (x1)

ANQ (x2) AQD (x1)

ANU (x2) AQB (x2)

ANS (x8)

AAN (x2)

AAX (x4)

5”

ANP (x1) AOR (x6)

ABP (x2) ANK (x4)

AQC (x2)

BGP (x2)

BGO (x2)

BLC (x1)

ANZ (x2)

ABN (x4)

ALM (x1)

Plastic Parts

7 1/16" (17,9 cm)

18

 SECTION 4 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

4.1 • Insert one end of the Tie Plate (BLC) into the slot on the Lower Extension Arm (BGP), then insert the opposite end of the

Tie Plate (BLC) into the slot on the other Lower Extension Arm (BGP) as shown.

• Do not overtighten the Cap Nut. If the end of the Bolt breaks

through the plastic cap, call our Customer Service Department.

Exposed threads on the end of the Bolt may cause serious injuries.

!

1/2” (≈13 mm)

(x1)

1/2” (≈13 mm)

(x1)

BLC BLC

BGP

AQB

AAN

BGP

BLC

AQB (x2) AAN (x2)

4.2 • Secure the Lower Extension Arms (BGP) together with the hardware shown. Use a 1/2” Socket Wrench to screw the Thread-

Cutting Bolts (AQB) through the Lower Extension Arms and the Tie Plate (BLC).

19

 SECTION 4 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

4.3

TOOLS AND HARDWARE REQUIRED / HERRAMIENTAS Y ACCESORIOS REQUERIDOS / OUTILS ET ACCESSOIRES REQUIS

• Insert the Extension Arm Caps (AQC) into the ends of the Lower Extension Arms (BGP) as shown.

 SECTION 4 (CONTINUED)

• Place the Top Pole (ALH) to the Lower Extension Arms (BGP) and secure them with the hardware shown.

4.4

BGP

AQC

BGP

AAX

AAD

AOR

ANZ ANZ ANZ

ANZ

ALH

• Tighten the Nut until it is

ﬂ ush with the end of the Bolt.

!

AAX (x1)

AAD (x1)

3/4" (≈19 mm)

(x2)

ANZ (x2)

AOR (x2)

20

 SECTION 4 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

AAX (x1)

4.6 • Attach the Upper Extension Arms (BGO) to the Top Pole (ALH) with the hardware as shown.

3/4" (≈19 mm)

(x2)

5”

BGO

AQD

AAX

ANK

ABN

ANK

AQD (x1)

ANK (x2)

• Tighten the Nut until it is ﬂ ush

with the end of the Bolt.

!

ABN (x2)

(x1)

4.5 • Insert the Pole Cap (ALM) into the Top Pole as shown. Line up the Pole Cap stirrups with the holes in the top of the Pole.

ALM

La page charge ...

Lifetime 90602 Le manuel du propriétaire

Lifetime 90602 Le manuel du propriétaire

dans d''autres langues