Faber TRATIS36SS600B Guide d'installation

Marque: Faber

Modèle: TRATIS36SS600B

Catégorie: Hottes

Taper: Guide d'installation

TRATIS36SS600-B

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

TRATTO IS 36"

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan

orlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.

BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE

AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this

fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on acciden-

tally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or

Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcientairisneededforpropercombustionandexhaustingofgasesthrough

theue(chimney)offuelburningequipmenttopreventbackdrafting.Followthe

heating equipment manufacturer's guideline and safety standards such as those

publishedbytheNationalFireProtectionAssociation(NFPA),andtheAmerican

SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and

the local code authorities.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

4. Ducted fans must always be vented to the outdoors.

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST

BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood

and the cooking surface or countertop. This hood has been approved by UL at this distance

from the cooktop. Overhead cabinets on both sides of this unit must be a minimum of 18" above

the cooking surface or countertop.

Consult the cooktop or range installation instructions given by the manufacturer before making

any cutouts. MOBILE HOME INSTALLATION The installation of this rangehood must conform

to the Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280).

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

Cold Weather installations

An additional back draft damper should be installed to minimize backward cold air ow and a

nonmetallic thermal break should be installed to minimize conduction of outside temperatures as

part of the vent system. The damper should be on the cold air side of the thermal break. The break

should be as close as possible to where the vent system enters the heated portion of the house.

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the

wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient

performance. The size of the ductwork should be uniform. Do not install two elbows together. Use

duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening

around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence

that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.

Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting

frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do

not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-delay

fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with

the electrical rating of this unit as specied on the serial/rating plate located inside the unit near the eld

wiring compartment.

ELECTRICAL INSTALLATION WITH WIRING BOX

THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform to the

requirements of the National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and

ordinances. Wire size and connections must conform with the rating of the appliance. Copies of the

standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

This appliance should be connected directly to the fused disconnect (or circuit breaker) through

exible, armored or nonmetallic sheathed copper cable. Allow some slack in the cable so the

appliance can be moved if servicing is ever necessary. A UL Listed, 1/2" conduit connector must

be provided at each end of the power supply cable (at the appliance and at the junction box).

When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through wood

must be sanded until smooth. A hole through metal must have a grommet.

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO

NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or

grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the rangehood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

RANGEHOOD DIMENSIONS

Min. 24"

MAIN PARTS

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Con-

trols, Light, Filters, Blower.

2 1 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

7.1 1 Telescopic frame complete with

extractor, consisting of:

7.1a 1 Upper frame

7.1b 1 Lower frame

10 1 Damper ø 5 7/8"

24 1 Junction Box

Ref. Qty. Installation Components

12f 2 Screws 3/16" x 9/16"

12c 2 Screws 1/8" x 1/4"

12e 4 Screws 1/8" x 3/8"

12q 4 Screws 1/4" x 9/16"

21 1 Drilling template

22 4 1/4" int. dia washers

Qty. Documentation

1 Instruction Manual

2.2

2.1

7.1

12q

12c

12e

12f

7.1a

7.1b

Available Accessories

-HighCeilingKitthatreplacesthelowerue.-sku#HIGH2.

-DuctlessKit-IncludesDuctlessDiverter,CharcoalFilters,Lowerchimneywithvent

grates-sku#DUCT2

-6"Make-UpAirDamperKit-MUDAMPER6

-8"Make-UpAirDamperKit-MUDAMPER8

-CFMReducerKit-CFMRED

-ActivatedCharcoalFilterAccessory-sku#FILTER2

- Wireless RemoteControlAccessory-REMCTRL

Parts needed

-6"RoundMetalductwork

Choose your ducting method

Non Ducted - Recirculation OptionDucted Venting Options Installation

RequiresDuctlessAccessoryKit

(purchasedseparately)

6 "

Putathick,protectivecoveringovercooktop,

set-in range or countertop to protect from

damageordirt.

Determineandclearlymarkwithapencilonthe

ceilingwheretherangehoodwillbeinstalled.

A template 21 for mounting the support is

supplied in the carton with the support. Use

thistemplatetomarkholesfor

supportontheceiling.

Determine and make necessary cuts for the

ductwork.Theduct openingisshownonthe

mountingtemplate.Install

ductworkbeforemountingthehood.

Determine the proper location for the Power

Supply Cable as indicated on the template.

Use a 1 1/4" Drill Bit to make this hole. Run

thePowerSupplyCable.Usecaulkingtoseal

aroundthehole.

A knockout for threading through the Power

Supply from the ceiling is located on the top

oftheframe.DonotconnectthePowerCable

totheWiringBoxorpowerupthehoodatthis

time.Runenoughpowercablefromtheceiling

toreachthewiringboxonthehood.

Ø 10 mm

1/16”

9/16”









24”

9/16”

1 1/4"

Donotmakeanycutoutsuntilyouhavedecidedwhetherthisinstallationwillbeductedor

non-ductandthenplanaccordingly.

DUE TO THE SIZE AND

WEIGHT OF THIS RANGE-

HOOD, THE SUPPORT MUST

BE FIRMLY ATTACHED TO

THE CEILING. For plaster or

sheet rock ceiling, the support

must be attached to the joists.

If this is not possible, a support

structure must be built behind

the plaster or sheet rock. The

manufacturer assumes no re-

sponsibility forinjury or damage

caused by improper installa-

tions.

WARNING

Chimney Flues Must Be Removed Before Installing the Hood

Loosen the two screws fastening the lower chimney

and remove this from the lower frame.

If you need to adjust the height of the frame,

proceed as follows:

• Unfasten the metric screws joining the two

columns, located at the sides of the frame

(1,2,3,4,5,6).

• Adjust the frame to the height required, then

ret all the screws removed as above.

Loosen the two screws fastening the upper chimney

and remove this from the upper frame.

MIN

740

MAX

940

After the regulation for height adjustment, insert

the upper chimney stack from above, and leave it

running free on the frame.

Upper Flue Must Be In Place

Before Proceeding

Install Damper that is included with the Hood before

connecting to the ductwork.

Only for Ducted Venting

Installation







Now take either your woods screws or bolts

depending on your set-up and screw all four

into the pilot holes and leave 1/4" of the

heads exposed.

Next install a UL or CSA listed strain relief

in the wiring box so that the screws can

be tightened after the chimney support is

attached to the ceiling.

Now lift the chimney support into it's nal

position and feed the electrical supply through

the strain relief.

Next position the chimney support so that

the large end of the keyhole slots are over

the ceiling attachment screws or bolts. Then

push the chimney support so that the bolts

are in the neck of the slots. Tighten all four

screws or bolts securely.

• The frame mountings must be secure to

withstand the weight of the hood and any

stresses caused by the occasional side

thrust applied to the device. On completion,

check that the base is stable, even if the

frame is subjected to bending.

• In all cases where the ceiling is not

strong enough at the suspension point,

the installer must provide strengthening

using suitable plates and backing pieces

anchored to the structurally sound parts.

Installation of wiring

connection

Remove the cover from the

eld wiring compartment.

DO NOT turn on the power until

installation is complete!

Connect the Power Supply

Cable to the rangehood.

Connect the Green (Green and

Yellow) ground wire under the

Green grounding screw. Attach

the White lead of the power

supply to the White lead of the

rangehood with a twist-on type

wire connector.

Attach the Black lead of the

power supply to the Black lead

of the rangehood with a twist-

on type wire connector.

Replace the eld wiring compart-

ment cover and the grease lters.

A. Home power supply cable

B. Black wires

C. UL listed wire connectors

D. White wires

E. Green (or bare) ground wire from home power supply connected to green ground screw

F. Range hood power supply cable

G. Range hood power supply cable connected to green ground screw

Version 02/12 - Page 8

FIGURE 13

MAKE THE ELECTRICAL CONNECTION

Remove the cover from the eld wiring compartment. (SEE

FIGURE 11) DO NOT turn on the power until installation is

complete! Connect the Power Supply Cable to the rangehood.

Connect the Green (Green and Yellow) ground wire under the

Green grounding screw. Attach the White lead of the power

supply to the White lead of the rangehood with a twist-on type

wire connector. Attach the Black lead of the power supply

to the Black lead of the rangehood with a twist-on type wire

connector.

1. The UPPER CHIMNEY

COVER (C in FIGURE 13)

attaches to the top of the

support structure using two

screws provided (G in FIGURE

13). If using the High Ceiling

Chimney Kit, use the UPPER

CHIMNEY COVER supplied

with the kit. Slide up and

attach the UPPER CHIMNEY

COVER.

2. Attach the duct work to the

DAMPER (M in FIGURE 1).

Make sure to seal all joints with

duct tape to prevent leaks.

3. The LOWER CHIMNEY

COVER (B in FIGURE 13)

attaches using two screws

provided (G in FIGURE 13).

Install the LOWER CHIMNEY

COVER by sliding it up over

the support and the UPPER

CHIMNEY COVER.

For ductless installations, line up the DUCTLESS DIVERTER

EXTENSIONS HORIZONTAL (B in FIGURE 12) with the holes

in the LOWER CHIMNEY COVER (D in FIGURE 12) and snap

in the VENT GRIDS (C in FIGURE 12).

INSTALLING THE RANGEHOOD

A. Home power supply cable

B. Black wires

C. UL listed wire connectors

D.White wires

E. Green (or bare) ground wire from home power supply

connected to green ground screw

F. Range hood power supply cable

G.Range hood power supply cable connected to green

ground screw

FIGURE 11

Ductless installations require

a Ductless Conversion

Kit whose components are

pictured in FIGURE 12. Do

not use the DAMPER (M

in FIGURE 1) for ductless

installations. The LOWER

CHIMNEY COVER (B

in FIGURE 1) should be

discarded and replaced by

the new one with holes from

the Ductless Conversion Kit

(D in FIGURE 12).

As indicated in FIGURE

12, place the DUCTLESS

DIVERTER (A) over the

exhaust opening of the EASY

CUBE (E). Fit the DUCTLESS

DIVERTER EXTENSIONS

HORIZONTAL (B) into the

DIVERTER (A).

FIGURE 12

FOR DUCTLESS INSTALLATIONS

Position the upper chimney section and x the upper

part to the frame using the 2 screws removed previously.

Similarly, position the lower chimney section and x the lower part to the frame using the 2 screws

removed previously.

Only For Ductless Installations

Ductless installations require a Ductless

Conversion Kit whose components are

pictured in FIGURE 12.

Do not use the DAMPER for ductless

installations. The LOWER CHIMNEY COVER

should be discarded and replaced by the

new one with holes from the Ductless

Conversion Kit (D in FIGURE 12).

As indicated in FIGURE 12, place the

DUCTLESS DIVERTER (A) over the exhaust

opening of the EASY CUBE (E). Fit the

DUCTLESS DIVERTER EXTENSIONS

HORIZONTAL (B) into the DIVERTER (A).

Version 02/12 - Page 8

FIGURE 13

MAKE THE ELECTRICAL CONNECTION

Remove the cover from the eld wiring compartment. (SEE

FIGURE 11) DO NOT turn on the power until installation is

complete! Connect the Power Supply Cable to the rangehood.

Connect the Green (Green and Yellow) ground wire under the

Green grounding screw. Attach the White lead of the power

supply to the White lead of the rangehood with a twist-on type

wire connector. Attach the Black lead of the power supply

to the Black lead of the rangehood with a twist-on type wire

connector.

1. The UPPER CHIMNEY

COVER (C in FIGURE 13)

attaches to the top of the

support structure using two

screws provided (G in FIGURE

13). If using the High Ceiling

Chimney Kit, use the UPPER

CHIMNEY COVER supplied

with the kit. Slide up and

attach the UPPER CHIMNEY

COVER.

2. Attach the duct work to the

DAMPER (M in FIGURE 1).

Make sure to seal all joints with

duct tape to prevent leaks.

3. The LOWER CHIMNEY

COVER (B in FIGURE 13)

attaches using two screws

provided (G in FIGURE 13).

Install the LOWER CHIMNEY

COVER by sliding it up over

the support and the UPPER

CHIMNEY COVER.

For ductless installations, line up the DUCTLESS DIVERTER

EXTENSIONS HORIZONTAL (B in FIGURE 12) with the holes

in the LOWER CHIMNEY COVER (D in FIGURE 12) and snap

in the VENT GRIDS (C in FIGURE 12).

INSTALLING THE RANGEHOOD

A. Home power supply cable

B. Black wires

C. UL listed wire connectors

D.White wires

E. Green (or bare) ground wire from home power supply

connected to green ground screw

F. Range hood power supply cable

G.Range hood power supply cable connected to green

ground screw

FIGURE 11

Ductless installations require

a Ductless Conversion

Kit whose components are

pictured in FIGURE 12. Do

not use the DAMPER (M

in FIGURE 1) for ductless

installations. The LOWER

CHIMNEY COVER ( B

in FIGURE 1) should be

discarded and replaced by

the new one with holes from

the Ductless Conversion Kit

(D in FIGURE 12).

As indicated in FIGURE

12, place the DUCTLESS

DIVERTER (A) over the

exhaust opening of the EASY

CUBE (E). Fit the DUCTLESS

DIVERTER EXTENSIONS

HORIZONTAL (B) into the

DIVERTER (A).

FIGURE 12

FOR DUCTLESS INSTALLATIONS

Screw the 2 screws 12f half way into the holes provided in the sides of the bottom of the frame.

Remove the grease lters from the hood canopy.

Remove any activated charcoal lters.

Lift the hood canopy and engage the screws 12f in the slots as far as they will go.

Working from below, x the

hood canopy to the frame

where indicated, using the 4

screws 12q and 4 washers 22

provided, then tighten all the

screws securely.

I







T[

[

Attachment of Hood Canopy

ConnectthecontrolconnectorCmd.

Placetheconnectorsinthejunctionbox24and

closeitusingthe4screwsprovided.

12c x 2

Fixthejunctionbox

tothehoodbody

usingthe2screws

12cprovided.



H

Make the Internal Electrical Connection

For Non-Ducted Recirculation

Option

RequiredActivatedCharcoalFilter

Accessory-sku#-FILTER2

(purchasedseparately)

Attacha

charcoal

lterinthe

correct

positionand

blockitby

thexing

hooksas

shown.

Unlockthexinghooks(towardsthebackofthe

inserthood)toremove.

Reinstall the grease lters

from the hood canopy.

USE AND CARE INFORMATION

T1.FanOffButton:TurntheblowerOff.Thefancanbeoperatedbypressinganyofthefansetting

buttons.

 Holddownthisbuttonfor2secondstoactivateDelayOfffunctionwhichwillkeepthefanOnfor15

minutesandautomaticallyshutOff.

T2.FanSettingsButtons:LowSpeed.

T3.FanSettingsButtons:MediumSpeed.

T4.FanSettingsButtons:HighSpeed/IntensiveSpeed.

 Holddownthebuttonfor2secondstoactivatetheINTENSIVESPEED,whichistimedtorunfor10

minutes.Attheendofthistimeitwillautomaticallyreturntothespeedsetbefore.Suitabletodeal

withmaximumlevelsofcookingfumes.

L. LightButton:On/Dim/Offswitchforthelights.PresstheLIGHTbuttontoturnthelighton,againto

setthelightstodimmer,andagaintoturnoff.

T1 T2 T3 T4 L

LT1 T2 T3 T4

For Best Results

Start the rangehood several minutes before cooking to develop proper airow.Allow the

rangehoodtooperateforseveralminutesaftercookingiscompletetoclearallsmokeand

odorsfromthekitchen.

Cleaningmetalgreaselters

The lters must be cleaned every 2 months of operation, or more

frequently for particularly heavy usage, and can be washed in

a dishwasher.

• Remove the Filters one at a time, pushing them towards

the back of the unit and at the same time pulling downward.

• Wash the Filters without bending them, and leave them to

dry completely before replacing. (If the surface of the lter

changes color as time goes by, this will have absolutely no

effect on the efciency of the lter itself.)

• Replace, taking care to ensure that the handle faces forwards.

Replacing Activated Charcoal Filter

The lter is not washable and cannot be regenerated, and must

be replaced approximately every 4 months of operation, or more

frequently for particularly heavy usage.

• Remove the Filters one at a time, pushing them towards

the back of the unit and at the same time pulling downward.

• Remove the saturated charcoal lter by releasing the xing

hooks.

• Fit the new lter and fasten it in its correct position.

• Replace, taking care to ensure that the handle faces forwards.

Lighting Unit

• LED lights must be replaced by Faber factory authorized

service.

Wiring Diagram

Dolce, Corrado

17-Feb-2016

Released

         

 





  

   



































































































 





































































 















January 4, 2016

FABER CONSUMER WARRANTY & SERVICE

All Faber products are warranted against any defect in materials or workmanship for the original purchaser

for a period of 1 year from the date of original purchase (requires proof of purchase). This warranty covers

labor and replacement parts. Faber, at its option, may repair or replace the product or components

necessary to restore the product to good working condition. To obtain warranty service, contact the dealer

from whom you purchased the range hood, or the local Faber distributor. If you cannot identify a local Faber

distributor, contact us at (508) 358-5353 for the name of a distributor in your area.

The following is not covered by Faber's warranty:

1. Service calls to correct the installation of your range hood, to instruct you how to use your range hood, to

replace or repair house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace range hood light bulbs, fuses or filters. Those consumable parts are

excluded from warranty coverage.

3. Repairs when your range hood is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,

installation not in accordance with electrical or plumbing codes or Faber documentation, or use of products

not approved by Faber.

5. Replacement parts or repair labor costs for units operated outside the United States or Canada, including

any non-UL or C-UL approved Faber range hoods.

6. Repairs to the hood resulting from unauthorized modifications made to the range hood.

7. Expenses for travel and transportation for product service in remote locations and pickup and delivery

charges. Faber range hoods should be serviced in the home.

THIS WARRANTY DOES NOT ALLOW RECOVERY OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, PERSONAL INJURY/WRONGFUL

DEATH OR LOST PROFITS FABER WARRANTY IS LIMITED TO THE ABOVE CONDITIONS AND TO THE WARRANTY PERIOD

SPECIFIED HEREIN AND IS EXCLUSIVE. EXCEPT AS EXPRESSLY SPECIFIED IN THIS AGREEMENT, FABER DISCLAIMS ALL

EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT LIMITATION, ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

This warranty gives you specific legal rights that may vary from state to state.

Model#: ______________________________ Serial #: _____________________________

VEUILLEZ LIRE ET CONSERVER LA PRÉSENTE NOTICE AVANT DE

COMMENCER L'INSTALLATION DE LA HOTTE DE CUISINE

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE D'UN FEU DE GRAISSE SUR LA TABLE DE

CUISSON:

a) Ne laissez jamais sans surveillance les éléments de la surface de cuisson à température élevée.

Les bouillonnements excessifs peuvent provoquer de la fumée et les débordements de graisse

peuvents'enammer.L'huiledoitêtrechaufféelentement,àunetempératurebasseoumoyenne.

b) Assurez-vous de toujours mettre en marche le ventilateur de la hotte lorsque vous cuisinez à

températureélevéeoupréparezunmetsambé(p.ex.crêpesSuzette,cerisesjubilé,bœufambé).

c) Nettoyez régulièrement les ventilateurs d'aspiration. Assurez-vous de ne pas laisser de la

graisses'accumulersurleventilateurouleltre.

d)Utiliseztoujoursdespoêlesetcasserolesdelatailleappropriée.Utiliseztoujoursdesustensiles

de cuisine de la taille adaptée à celle de l'élément chauffant.

AVERTISSEMENT:-POURPRÉVENIRLESBLESSURESENCASDEFEUDEGRAISSESURLA

TABLEDECUISSON,SUIVEZLESRECOMMANDATIONSSUIVANTES*:

a) ÉTOUFFEZ LES FLAMMES à l'aide d'un couvercle hermétique, d'une plaque à biscuits ou d'un

plateau métallique, puis éteignez le brûleur. FAITES ATTENTION AUX BRÛLURES. Si le feu ne

s'éteint pas immédiatement, QUITTEZ LES LIEUX ET APPELEZ LES POMPIERS.

b) NE PRENEZ JAMAIS UNE CASSEROLE EN FLAMME - Vous pourriez vous brûler.

c) N'UTILISEZ JAMAIS DE L'EAU, ni un linge à vaisselle ou un torchon mouillé, pour éteindre le

feu. Cela pourrait provoquer une violente explosion de vapeur.

d)UtilisezunextincteurUNIQUEMENTsi:

1. Vousêtescertainqu'ils'agitd'unextincteurdeclasseABCetquevousconnaissezbien

son mode d'emploi.

2. Le feu est de faible intensité et se limite à l'endroit où il a démarré.

3. Les pompiers ont déjà été appelés.

4. Unevoiedesortiesetrouvederrièrevouspendantquevouséteignezlesammes.

* D'après le guide «Kitchen Firesafety Tips» publié par la NFPA aux États-Unis

AVERTISSEMENT - POUR RÉDUIRE LE RISQUE D'INCENDIE OU DE CHOC ÉLECTRIQUE, n'utilisez

jamais ce ventilateur en association avec un dispositif de réglage de vitesse à semi-conducteurs.

AVERTISSEMENT - POUR RÉDUIRE LES RISQUES D'INCENDIE, DE CHOC ÉLECTRIQUE OU

DEBLESSURECORPORELLE,RESPECTEZLESINSTRUCTIONSSUIVANTES:

1. Utilisez cet appareil uniquement de la façon prévue par le fabricant. Pour toute question,

communiquez avec le fabricant.

2. Avant de procéder à l'entretien ou au nettoyage de l'appareil, coupez l'alimentation au

niveau du panneau électrique et verrouillez-le pour vous assurer que l'électricité n'est pas

rétablie accidentellement. S'il n'est pas possible de verrouiller le dispositif d'interruption de

l'alimentation,afchezdefaçonfermeetbienvisibleunavisdedanger,parexempleàl'aide

d'une étiquette sur le panneau.

ATTENTION:Destinéàunusagedeventilationgénéraleuniquement.N'utilisezpascedispositif

pour l'aspiration de vapeurs ou de matériaux dangereux ou explosifs.

AVERTISSEMENT - POUR RÉDUIRE LES RISQUES D'INCENDIE, DE CHOC ÉLECTRIQUE OU

DEBLESSURECORPORELLE,RESPECTEZLESINSTRUCTIONSSUIVANTES:

1. L'installationetlebranchementélectriquedoiventêtreréalisésparuntechnicienqualié

et conformément à tous les codes et normes en vigueur, incluant ceux concernant la con-

struction à l'épreuve du feu.

2. Andegarantirunecombustionetuneévacuationadéquatesdesgazparlesconduites

de la cheminée des appareils à combustion, une bonne aération est nécessaire pour éviter

le refoulement. Respectez les lignes directrices fournies par le fabricant du matériel chauf-

fant, ainsi que les normes de sécurité comme celles publiées par la National Fire Protection

Association(NFPA)etlaAmericanSocietyforHeating,RefrigerationandAirConditioning

Engineers(ASHRAE)auxÉtats-Unis,ainsiquelescodesenvigueurdansvotrerégion.

La page charge ...

Faber TRATIS36SS600B Guide d'installation

Marque: Faber

Modèle: TRATIS36SS600B

Catégorie: Hottes

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Faber TRATIS36SS600B Installation guide

Faber TRATIS36SS600B Guide d'installation

Faber TRATIS36SS600B Guide d'installation

dans d''autres langues

Documents connexes