Hotpoint LTF 8B116 EU Mode d'emploi

LTF 8B116 EU
Hotpoint
Marque
Hotpoint
Modèle
LTF 8B116 EU
Catégorie
Lave-vaisselle
Taper
Mode d'emploi
EN
1
Operating instructions
Contents
Product Fiche, 2
Precautions and advice, 3
General safety
Disposal
Saving energy and respecting the environment
Installation and Assistance, 4-5
Positioning and levelling
Connecting the water and electricity supplies
Advice regarding the first wash cycle
Technical data
Assistance
Description of the appliance, 6
Overall view
Control panel
Loading the racks, 7-8
Lower rack
Cutlery basket
Upper rack
Cutlery tray
Adjusting upper rack
Start-up and use, 9
Starting the dishwasher
Measuring out the detergent
Wash cycles, 10
Table of wash cycles
Special wash cycles and Options, 11
Rinse aid and refined salt, 12
Measuring out the rinse aid
Measuring out the refined salt
Care and maintenance, 13
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Troubleshooting, 14
English, 1
EN
LTF 8B116
DISHWASHER
Français, 15
FR
NL
Nederland, 30
EN
2
Product Fiche
Brand
HOTPOINT ARISTON
Model
LTF 8B116
Rated capacity in standard place settings (1)
13
Energy efciency class on a scale from A+++ (low consumption) to D (high consumption)
A+
Energy consumption per year in kWh (2)
293.0
Energy consumption of the standard cleaning cycle in kWh
1.03
Power consumption of the off-mode in W
0.5
Power consumption of the left-on mode in W
5.0
Water consumption per year in litres (3)
3080.0
Drying efcacy class on a scale from G (low efcacy) to A (high efcacy)
A
Programme time for standard cleaning cycle in minutes
190’
The duration of the left-on mode in minutes
10
Noise in dB(A) Re 1pW
46
Built-in model
Yes
NOTES
1) The information on the label and che relates to the standard cleaning cycle, this programme is suitable to clean normally soiled
tableware and it is the most efcient programme in terms of combined energy and water consumption. The standard cleaning cycle
corresponds to the Eco cycle.
2) Based on 280 standard cleaning cycles using cold water ll and the consumption of the low power modes. Actual energy
consumption depends on how the appliance is used.
3) Based on 280 standard cleaning cycles. Actual water consumption depends on how the appliance is used.
Product Fiche
EN
3
* Only available in selected models.
Precautions and advice
This appliance was designed and
manufactured in compliance with international
safety standards The following information has
been provided for safety reasons and should
therefore be read carefully.
Keep this instruction manual in a safe place for
future reference. If the appliance is sold, given
away or moved, please ensure the manual is kept
with the machine.
Please read these instructions carefully: they
contain important information on installation, use
and safety.
This appliance is designed for domestic use or
similar applications, for example:
- staff kitchen areas in shops, offices and other
work environments;
- farmhouses;
- use by guests in hotels, motels and other
residential settings;
- bed & breakfasts.
General safety
• The appliance should not be operated by
people (including children) with reduced
physical, sensory or mental capacities, or by
inexperienced people who are not familiar with
the product, unless supervision or instructions
on how to use it are provided by someone who
assumes responsibility for their safety.
• Anadultmustsupervisechildrenatalltimesto
prevent them from playing with the appliance.
• Theappliance was designed for domestic
use inside the home and is not intended for
commercial or industrial use.
• Theappliancemustbeusedbyadultsonlyto
wash domestic crockery in accordance with
the instructions in this manual.
• Theappliancemustnotbeinstalledoutdoors,
even in covered areas. It is extremely dangerous
to leave the machine exposed to rain and
storms.
• Donottouchtheappliancewhenbarefoot.
• Whenunpluggingtheappliancealwayspullthe
plug from the mains socket. Do not pull on the
cable.
• Thewatersupplytapmustbeshutoffandthe
plug should be removed from the electrical
socket before cleaning or maintaining the
appliance.
• Iftheappliancebreaksdown,donotunderany
circumstances touch the internal parts in an
attempt to perform the repair work yourself.
• Do not lean or sit on theopendoorofthe
appliance: this may cause the appliance to
overturn.
•Thedoorshouldnotbeleftopenasitmaycreate
a dangerous obstacle.
• Keepdetergentandrinseaidoutofreachof
children.
• Thepackagingmaterialshouldnotbeusedas
a
toy for children.
Disposal
• Disposal of packaging material: observe local
legislation so that the packaging may be
reused.
• The European Directive 2012/19/EU relating
toWasteElectricalandElectronicEquipment
(WEEE) states that household appliances
should not be disposed of using the normal
solidurbanwastecycle.Exhaustedappliances
should be collected separately in order to
optimise the re-using and recycling rate of the
materials inside the machine, while preventing
potential damage to the environment and public
health. The crossed-out dustbin symbol is
marked on all products to remind the owners
of their obligations regarding separated waste
collection.
For further information relating to the correct
disposal of household appliances, owners may
contact the relevant public authority or the local
appliance dealer.
Saving energy and respecting the
environment
Saving water and energy
• Only begin a wash cycle when the dishwasher
isfull.Whilewaitingforthedishwashertobe
filled, prevent unpleasant odours using the Soak
cycle
(seeWashcycles)
.
• Selectawashcyclethatissuitedtothetype
of crockery and to the soil level of the crockery
using the Table of wash cycles:
-fordisheswithanormalsoillevelusetheEco
washcycle,whichensureslowenergy/water
consumption levels.
- If the load is smaller than usual activate the
Half Load option*
(see Start-up and use).
• Ifyourelectricitysupplycontractgivesdetailsof
electricity-saving time bands, run wash cycles
when electricity prices are lower. The Delayed
Start button *
(see Start-up and use)
helps you
organise the wash cycles accordingly.
Phosphate-free and chlorine-free detergents
containing enzymes
• Westronglyrecommendthatyouusedetergents
that do not contain phosphates or chlorine, as
these products are harmful to the environment.
• Enzymesprovideaparticularlyeffectiveaction
at temperatures around 50°C. As a result
detergentscontainingenzymescanbeusedin
conjunction with low-temperature wash cycles
in order to achieve the same results as a normal
65°C wash cycle.
•Toavoidwastingdetergent,usetheproduct
in appropriate quantities based onthe
manufacturer’s
recommendations, the hardness
ofthewater,the soil levelandthe quantity
ofcrockerytobewashed. Even if they are
biodegradable, detergents contain substances
which may alter the balance of nature.
EN
4
Installation and Assistance
* Only available in selected models.
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto its
back.
Positioning and levelling
1. Remove the appliance from all packaging and check that
it has not been damaged during transportation. If it has been
damaged, contact the retailer and do not proceed any further
with the installation process.
2.Arrangethedishwashersothatitssidesorbackpanelarein
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop
*
(see the Assembly
Instruction sheet.)
3. Position the dishwasher on a level sturdy floor. If the floor
is uneven, the front feet of the appliance should be adjusted
untilitreachesahorizontalposition.Iftheapplianceislevelled
correctly, it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
4
*. To adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. Turn the
spanner in a clockwise direction to increase the height and in an
anticlockwise direction to decrease it
(see Building-in Instruction
sheet attached to the documentation.)
Connecting the water and electricity supplies
Connection to the water and electricity supplies should only
beperformedbyaqualifiedtechnician.
The dishwasher should not stand on the water hoses or
electricity supply cable.
The appliance must be connected to the water supply
network using new hoses.
Do not use old piping.
The water inlet and outlet hoses and the electricity supply cable
may be positioned towards the right or the left in order to achieve
the best possible installation.
Connecting the water inlet hose
• Toasuitablecoldwaterconnectionpoint:beforeattaching
the hose, run the water until it is perfectly clear so that any
impurities that may be present in the water do not clog the
appliance; after performing this operation, screw the inlet
hose tightly onto a tap with a ¾ gas threaded connection.
• Toasuitablehotwaterconnectionpoint:yourdishwasher
may be supplied with hot water from the mains supply (if you
have a central heating system with radiators) provided that it
does not exceed a temperature of 60°C.
Screw the hose to the tap as described for connection to a
cold water supply.
If the inlet hose is not long enough, contact a specialist store
or an authorised technician
(see Assistance.)
The water pressure must be within the values indicated in
the Technical Data table
(see adjacent information.)
The hose should not be bent or compressed.
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain duct with
a minimum diameter of 4 cm.
The outlet hose must be at a height ranging from 40 to 80 cm
fromthefloor/surfacewherethedishwasherrests(A).
Before connecting the water outlet hose to the sink drain, remove
the plastic plug (B).
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply
in the event of anomalies or leaks from inside the appliance.
Somemodelsarealsoequippedwiththesupplementarysafety
device New Acqua Stop
*, which guarantees anti-flooding
protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstances should the water inlet hose be cut, as
it contains live electrical parts.
Electrical connection
Before inserting the plug into the electrical socket, make sure
that:
• Thesocketisearthedandcomplieswithcurrentregulations.
• thesocketcanwithstandthemaximumloadoftheappliance,
which is indicated on the data plate located on the inside of
the door
(see Description of the appliance);
• Thepowersupplyvoltagefallswithinthevaluesindicatedon
the data plate on the inside of the door.
• Thesocketiscompatiblewiththeplugoftheappliance.If
this is not the case, ask an authorised technician to replace
the plug (
see Assistance
); do not use extension cables or
multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order
topreventallpotentialhazards
(see Assistance.)
EN
5
Anti-condensation strip*
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order
to protect it from any condensation which may form.
Advice regarding the first wash cycle
After the installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack, if any.
Immediately before the first washing, completely fill the salt
dispenser with water and add only then approximately 1 kg of salt
(see chapter entitled Rinse aid and refined salt). The water may
overflow: this is normal and is not a cause for concern. Select
the water hardness value (see chapter entitled Rinse aid and
refined salt). - After the salt has been poured into the machine,
theLOWSALTindicatorlight*switchesoff.
If the salt container is not filled, the water softener and
the heating element may be damaged as a result.
Technical data
Dimensions
width 59.5 cm
height 82 cm
depth 57 cm
Capacity 13 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply voltage See appliance data plate
Total absorbed power See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2009/125/EC (Comm. Reg.
1016/2010) (Ecodesign)
-97/17/EC (Labelling)
-2012/19/EC (WEEE)
The machine has a buzzer/set of tones
(depending on the
dishwasher model
) to inform the user that a command has
been implemented: power on, cycle end etc.
The symbols/indicator lights/LEDs on the control panel/
display may vary in colour and may have a flashing or fixed
light
(depending on the dishwasher model)
.
The display provides useful information concerning the type
of wash cycle, drying/wash-cycle phase, remaining time,
temperature etc etc.
* Only available in selected models.
Assistance
Before contacting Assistance:
• Checkwhethertheproblemcanberesolvedusingthe
Troubleshooting guide
(see Troubleshooting).
• Restarttheprogrammetocheckwhethertheproblem
has ceased to exist.
• Ifthe problempersists, contactthe Authorised
Technical Assistance Service.
Never use the services of unauthorised technicians.
Please have the following information to hand:
• Thetypeofmalfunction.
• Theappliancemodel(Mod.).
• Theserialnumber(S/N).
This information can be found on the appliance data plate
(see Description of the appliance)
.
EN
6
Overall view
Description of the
appliance
***Only in completely built-in models.
* Only available in selected models.
The number and type of wash cycles and options may vary depending on the dishwasher model.
1. Upper rack
2. Upper sprayer arm
3. Tip-up dispensers
4. Rack height adjuster
5. Lower rack
6. Lower sprayer arm
7. Washingfilter
8. Salt dispenser
9. Detergent and rinse-aid dispensers and
device Active Oxigen
*
10. Data plate
11. Control panel
****
Control panel
Select wash cycle button
Salt indicator light
Rinse aid indicator light
Wash cycle number and
remaining time indicator light
Delayed start button
ON-OFF/Reset button
and indicator light
Delayed start indicator light
EN
7
Loading the racks
Tips
Before loading the racks, remove all food residues from the
crockeryandemptyliquidsfromglassesandcontainers.No
preventive rinsing is needed under running water.
Arrange the crockery so that it is held in place firmly and does
not tip over; and arrange the containers with the openings facing
downwardsand the concave/convex partsplacedobliquely,
thus allowing the water to reach every surface and flow freely.
Make sure that the lids, handles, trays and frying pans do not
prevent the sprayer arms from rotating. Place any small items
in the cutlery basket.
Since plastic dishes and non-stick frying pans usually retain more
water drops, their drying will be not so good as that of ceramic
or stainless-steel dishes.
Lightweight items such as plastic containers should be placed
in the upper rack and arranged so that they cannot move.
After loading the appliance, make sure that the sprayer arms
can rotate freely.
Lower rack
The lower rack can hold pans, lids, dishes, salad bowls, cutlery
etc. Large plates and lids should ideally be placed at the sides.
Very soiled dishes and pans should be placed in the lower rack
because in this sector the water sprays are stronger and allow
a higher washing performance.
Several dishwasher models are fitted with tip-up sectors
*.
They can be used in a vertical position when arranging dishes
orinahorizontalposition(lower)toloadpansandsaladbowls
easily.
Cutlery basket
Thebasket is equipped with topgrilles forimproved cutlery
arrangement. The cutlery basket should be positioned only at
the front of the lower rack.
Knives and other utensils with sharp edges must be placed
in the cutlery basket with the points facing downwards or they
mustbepositionedhorizontallyinthetip-upcompartmentson
the upper rack
Upper rack
Load this rack with delicate and lightweight crockery such as
glasses, cups, saucers and shallow salad bowls.
Several dishwasher models are fitted with tip-up sectors
*.
Theycan be used ina verticalposition whenarranging tea/
dessert saucers or in a lower position to load bowls and food
containers.
*Only available in selected models with different numbers and
positions.
EN
8
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper rack
may be moved to a higher or lower position.
The height of the upper rack should be adjusted WHEN THE
RACK IS EMPTY.
NEVER raise or lower the rack on one side only.
IftherackisequippedwithaLift-Up
device*
(see figure)
, lift
it up by holding its sides. To restore the lower position, press
the levers (A) at the sides of the rack and follow the rack down.
Unsuitable crockery
• Woodencrockeryandcutlery.
• Delicatedecoratedglasses,artistichandicraftandantique
crockery. Their decorations are not resistant.
• Parts in synthetic materialwhich donotwithstand high
temperatures.
• Copperandtincrockery.
• Crockerysoiledwithash,wax,lubricatinggreaseorink.
Thecoloursofglassdecorationsandaluminium/silverpiecescan
change and fade during the washing process. Some types of
glass(e.g.crystalobjects)canbecomeopaqueafteranumber
of wash cycles too.
Damage to glass and crockery
Caused by:
• Typeofglassandglassproductionprocess.
• Chemicalcompositionofdetergent.
• Watertemperatureofrinsecycle.
Tips:
• Onlyuse glasses and porcelain guaranteedby the
manufacturer as dishwasher safe.
• Useadelicatedetergentsuitableforcrockery.
• Collectglassesandcutleryfromthedishwasherassoonas
the wash cycle is over.
Theupperrackcanbeadjustedforheightbasedonrequirements:
high position to place bulky crockery in the lower rack and low
positiontomakethemostofthetip-upcompartments/sectors
by creating more space upwards.
Tip-up compartments with adjustable position
The side tip-up compartments can be positioned at three
differentheightstooptimizethearrangementofcrockeryinside
the rack.
Wineglassescanbeplacedsafelyinthetip-upcompartments
by inserting the stem of each glass into the corresponding slots.
Cutlery tray*
Some dishwasher models are fitted with a sliding tray which
can be used to hold serving utensils or small cups. For optimum
washing performance avoid positioning bulky crockery directly
below the tray. The cutlery tray can be removed
(see Figure).
Before loading the tray, make sure the supports are properly
coupled to the upper rack
(see Figure).
* Only available in selected models.
EN
9
Start-up and use
* Only available in selected models.
Measuring out the detergent
A good wash result also depends on the correct
amount of detergent being used. Exceeding the stated
amount does not result in a more effective wash and
increases environmental pollution.
Based on how soiled the items are, the amount can be
adjusted to individual cases using powder or liquid
detergent.
In the case of normally soiled items, use approximately
either 35 gr (powder detergent) or 35 ml (liquid detergent).
If tablets are used, one tablet will be enough.
If the crockery is only lightly soiled or if it has been rinsed
with water before being placed in the dishwasher, reduce
the amount of detergent used accordingly.
For good washing results also follow the instructions shown
on the detergent box.
For further questions please ask the detergent producers'
Advice Offices.
To open the detergent dispenser use the opening device “A”.
Introduce the detergent into the dry dispenser “B” only.
Place the amount of detergent for pre-washing directly
inside the tub.
1.WhenmeasuringoutthedetergentrefertotheTableofwash
cyclestoaddtheproperquantity.CompartmentB comprises
alevel showing the maximum quantityof liquidor powder
detergent that can be added to each cycle.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the wash cycle.
If all-in-one detergents are used, we recommend using the TABS
option, because it adjusts the cycle so that the best washing
and drying results are always achieved.
Only use detergent which has been specifically designed
for dishwashers.
DO NOT USE washing-up liquid.
Using excessive detergent may result in foam residue
remaining in the machine after the cycle has ended.
The use of tablets is only recommended for models which
offer the MULTI-FUNCTIONAL TABLETS option.
To achieve the best results from each washing and drying
cycle, powder detergent, liquid rinse aid and salt should
be used.
Starting the dishwasher
1. Turn the water tap on.
2.Open the doorand pressON-OFFbutton: the ON/OFF
indicator lights, options and the display come on.
3. Measure out the detergent.
(see adjacent information).
4. Load the racks
(see Loading the racks)
.
5. Select the wash cycle in accordance with the type of crockery
and its soil level
(see table of wash cycles)
by pressing the P
button.
6. Select the wash options
*.
(see Special wash cycles and
options)
.
7. Start the wash cycle by shutting the door.
8. The end of the wash cycle is indicated by beeps and by the
flashing of the wash cycle number on the display. Open the door,
switchofftheappliancebypressingtheON/OFFbutton,shut
off the water tap and unplug the appliance from the electricity
socket.
9.Waitforafewminutesbeforeremovingthecrockery,inorder
to avoid burns. Unload the racks, beginning with the lower level.
- The machine will switch off automatically during
certain extended periods of inactivity, in order to
minimise electricity consumption.
AUTO WASH CYCLES*:some models of dishwashers are
equippedwithaspecialsensorwhichcanbeusedtoassess
the level of soiling and automatically setting the most efficient
and economic wash cycle accordingly.
The duration of the Auto wash cycles may vary due to the
operation of the sensor.
If the crockery is only lightly soiled or if it has been rinsed
with water before being placed in the dishwasher, reduce the
amount of detergent used accordingly.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection process,
it is possible to change the cycle, provided that it has only just
begun: open the door taking care to avoid the escaping steam,
bypressingandholdingtheON/OFFbutton,themachinewill
switchoff.SwitchthemachinebackonusingtheON/OFFbutton
and select the new wash cycle and any options desired; start
the cycle by closing the door.
Adding extra crockery
Withoutswitchingoffthemachine,openthedoor,takingcare
to avoid the escaping steam, and place the crockery inside the
dishwasher. Shut the door and the cycle will begin from the point
at which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a power
cut, the cycle stops. It starts again from the point at which it
was interrupted once the door has been shut or the electricity
supply is restored.
EN
10
Wash cycles
Wash-cycledataismeasuredunderlaboratoryconditionsaccordingtoEuropeanStandardEN50242.
Based on the different conditions of use, the wash-cycle duration and data can change.
The number and type of wash cycles and options may vary depending on the dishwasher model.
Wash cycle
Wash cycle
which
include
drying
Options
Approximate
duration of wash
cycles
Water
consumption
(l/cycle)
Energy
consumption
(KWh/cycle)
1. Eco Yes
Delayed start
03:10’ 11 1,03
2. Auto Intensive Yes
Delayed start
02:00’ - 03:10’ 14,0 - 15,5 1,5 - 1,8
3. Auto Normal Yes
Delayed start
01:30’ - 02:30’ 14,5 - 16,0 1,2 - 1,35
4. Auto Fast No
Delayed start
00:40’ - 01:20’ 13,0 - 14,5 1,15 - 1,25
5. Delicate Yes
Delayed start
01:40’ 11,0 1,1
6. Express 40’ No
Delayed start
00:40’ 9,5 0,9
7. Soak No
Delayed start
00:12’ 4,5 0,01
8. Sanitazing Yes
Delayed start
01:20’ 10,0 1,25
Instructions on wash-cycle selection and detergent dosage
1.TheECOwashcycleisthestandardcycletowhichtheenergylabeldatarefers.Itcanbeusedtowashcrockerywithanormal
soillevelandisthemostefficientcycleintermsofenergyandwaterconsumptionforthistypeofcrockery.27gr/ml+6gr/ml**–1
Tab (**Quantity of pre-washing detergent)
2.Heavilysoileddishesandpans(nottobeusedfordelicateitems).30gr/ml–1Tab
3.Normallysoiledpansanddishes.27gr/ml+6gr/ml**–1Tab
4.Limitedquantityofdailysoiling(idealfor4placesettings)25gr/ml–1Tab
5.Cyclefordelicateitems,whicharemoresensitivetohightemperatures30gr/ml–1Tab
6.Fastcycletobeusedforslightlydirtydishes(idealfor2placesettings)25gr/ml–1Tab
7. Pre-wash while awaiting completion of the load with the dishes from the next meal. No detergent.
8.High-temperaturedisinfectingcycle.Idealtocleancrockeryandfeedingbottles.30gr/ml–1Tab
Standbyconsumption:Left-onmodeconsumption:5W-Offmodeconsumption:0.5W.
EN
11
Special wash cycles and Options
Notes:
Optimumperformancelevelswhenusingthe“Fast"and"Express
40’” cycles can be achieved by respecting the specified number
of place settings.
To reduce consumption, only run the dishwasher when it is full.
Note for Test Laboratories: forinformationoncomparativeEN
testing conditions, please send an email to the following address:
[email protected]
Wash options
If an option is not compatible with the selected wash cycle
(see table of wash cycles), the corresponding LED flashes
rapidly 3 times and beeps will sound.
Delayed start
The start of the wash cycle may be delayed for a
period of time between 1 and 12 hours.
1.Press theDELAYEDSTART button:the corresponding
symbol appears on the display; each time you press the
button,thetime(1h,2h,etc.uptomax.12h)fromthestart
of the selected wash cycle will be increased.
2.Selectthecycleandclosethedoor:thetimerwillbegin
counting down;
3. Once this time has elapsed, the indicator light switches
off and the wash cycle begins.
To adjust the delay time and select a smaller period of time,
presstheDELAYEDSTARTbutton.Tocancelit,pressthe
button repeatedly until the selected delayed start indicator
light switches off. The wash cycle will start automatically as
soon as the door is shut.
EN
12
Rinse aid and refined salt
Only use products which have been specifically designed
for dishwashers.
Do not use table/industrial salt or washing-up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
any rinse aid. However, we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard.
(Follow the instructions given on the packaging).
If you do not add salt or rinse aid, the LOW SALT* and
LOW RINSE AID indicator lights will stay lit.
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water runs off
the surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:
• WhentheLOWRINSEAIDindicatorlight* on the control panel
is illuminated, a reserve supply of rinse aid is still available
for1-2cycles;
1. Open the dispenser
“D” by pressing and pulling up the tab
on the lid;
2.Carefully introduce the rinse aidas faras themaximum
reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
mayadjustthequantityofrinseaidused.Switchonandoffthe
dishwasherusingtheON/OFFbutton.PresstheP button three
times.PresstheON/OFFbutton,thesetlevelappearsonthe
display
(set to factory level).
Adjust the rinse aid supply level with the P button.
Press the ON/OFF button to save the adjustment setting.
TherinseaidlevelcanbesettoZERO,insuchacasetherinse
aid will not be supplied and the low rinse aid indicator light in
case of running out.
A maximum of 4 levels can be set according to the dishwasher
model.
•Iftherearestreaksonthecrockery,settoalownumber(1-2).
•Incaseofdropsofwaterorlimescalemarks,settoahigh
number number (3-4).
Setting the water hardness
Everydishwasherisequippedwithawatersoftenerwhich,by
using refined salt designed especially for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the
water hardness level in your area. This information can be
obtained from your local water supplier.
SwitchonandoffthedishwasherusingtheON/OFFbutton.Press
and hold the P button for a few seconds until you hear a beep.
SwitchonthedishwasherwiththeON/OFFbutton,thesetlevel
appears on the display
(water softener set to medium level).
Adjust the water hardness level with the P button,
(1-2-3-4-5*
see water hardness table)
up to a max. of 5 levels.
Press the ON/OFF button to save the adjustment setting.
Evenifusingmulti-functionaltablets,thesaltdispensershould
still be filled.
(°dH = hardness measured in German degrees - °f = hardness
measuredinFrenchdegrees–mmol/l=millimolesperlitre)
Measuring out the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
Refined salt removes limescale from the water, thus avoiding
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
• Whenthegreenfloat
* cannot be seen by simply looking at
the cap of the salt dispenser;
• WhentheLOWRINSEAIDindicatorlightonthecontrolpanel
is illuminated
*;
1. Remove the lower rack and unscrew the cap (anticlockwise).
2.Thefirsttimeyoudothis:fillthewater
tank right up to its edge.
3. Position the funnel
*
(see figure)
and
fill the salt dispenser up to the edge
(approximately 1 kg). It is normal for a
little water to leak out.
4. Remove the funnel* and wipe any salt
residues away from the opening; rinse the cap under running
water and then screw it on, the head facing downwards so as to
let the water flow out of the four slots (star-shaped arrangement)
in the lower part of the cap (cap with green float
*).
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
Whennecessary,measureoutthesaltbeforeawashcycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
* Only available in selected models.
Water Hardness Table
Average salt dispenser
capacity duration
**
level °dH °fH mmol/l months
1 0 - 6 0 - 10 0 - 1 7 months
2 6 - 11 11 - 20 1,1 - 2 5 months
3 12 - 17 21 - 30 2,1 - 3 3 months
4 17 - 34 31 - 60 3,1 - 6 2 months
5
*
34 - 50 61 - 90 6,1 - 9 2/3 weeks
For values between 0°f and 10°f, we do not recommend the use of salt.
* a setting of 5 may increase cycle duration.
** 1 wash cycle per day.
M
A
X
EN
13
Care and maintenance
Shutting off the water and electricity
supplies
• Turnoffthewatertapaftereverywashcycletoavoidleaks.
• Alwaysunplug the appliance whencleaning it and when
performing maintenance work.
Cleaning the dishwasher
• Theexternalsurfacesofthemachineandthecontrolpanel
can be cleaned using a non-abrasive cloth which has been
dampened with water. Do not use solvents or abrasive
products.
• Anymarksontheinsideoftheappliancemayberemoved
using a cloth dampened with water and a little vinegar.
Preventing unpleasant odours
• Alwayskeepthedooroftheapplianceajarinordertoavoid
moisture from forming and being trapped inside the machine.
• Cleanthesealsaroundthedooranddetergentdispensers
regularly using a damp sponge. This will avoid food becoming
trapped in the seals, which is the main cause behind the
formation of unpleasant odours.
Cleaning the sprayer arms
Food residue may become encrusted onto the sprayer arms
and block the holes used to spray the water. It is therefore
recommended that you check the arms from time to time and
clean them with a small non-metallic brush.
The two sprayer arms may both be removed.
To remove the upper sprayer arm,
turn the plastic locking ring in an
anti-clockwise direction. The upper
sprayer arm should be replaced
so that the side with the greater
number of holes is facing upwards.
The lower sprayer arm can be
removed by pressing on the side
tabs and pulling it upwards.
Cleaning the water inlet filter*
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free
of impurities before performing the necessary connections. If this
precaution is not taken, the water inlet could become blocked
and damage the dishwasher.
Clean the water inlet filter at the tap outlet regularly.
- Turn off the water tap.
- Unscrew the end of the water inlet hose, remove the filter and
clean it carefully under running water.
- Re-place the filter and screw the water hose back into position.
Cleaning the filters
The filter assembly consists of three filters which remove food
residues from the washing water and then recirculate the water.
They should be cleaned if you wish to achieve the best results
in every wash.
Clean the filters regularly.
The dishwasher should not be used without filters or if the
filter is loose.
•Afterseveralwashes,checkthefilterassemblyandifnecessary
clean it thoroughly under running water, using a non-metallic
brush and following the instructions below:
1. Turn the cylindrical filter C in an anti-clockwise direction and
pull it out
(fig. 1).
2. Remove the cup filter B by exerting a slight pressure on the
side flaps
(fig.2);
3. Slide out the stainless-steel plate filter A.
(fig. 3).
4. Inspect the trap and remove any food residues. NEVER
REMOVE the wash-cycle pump protection
(black detail) (fig.4).
After cleaning the filters, re-place the filter assembly and fix it in
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
Leaving the machine unused for extended
periods
• Disconnecttheappliancefromtheelectricitysupplyandshut
off the water tap.
• Leavethedooroftheapplianceajar.
• Whenyoureturn,runawashcyclewhenthedishwasheris
empty.
* Only available in selected models.
EN
14
Troubleshooting
Whenevertheappliancefailstowork,checkforasolutionfromthefollowinglistbeforecallingforAssistance.
* Only available in selected models.
Problem: Possible causes / Solutions:
The dishwasher does not start or
cannot be controlled.
• Switch off the appliance by pressing the ON/OFF button, switch it back on after approximately
one minute and reset the program.
• The appliance has not been plugged in properly.
• The dishwasher door has not been shut properly.
The door won’t close. • The lock was released. Strongly push the door until a “clacking” noise is heard.
No water drains out from the
dishwasher.
• The dishwasher cycle has not yet nished.
• The water inlet hose is bent (see Installation).
• The drain duct is blocked.
• The lter is clogged up with food residues.
The dishwasher makes excessive
noise.
• The dishes are rattling against each other or against the sprayer arms.
• Excessive foam presence: the detergent has not been measured out correctly or it is not
suitable for use in dishwashers. (see Start-up and use).
The dishes and glasses are covered
in a white lm or limescale deposits.
• The level of the rened salt is low or the dosage setting is not suited to the hardness of the
water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
The dishes and glasses are streaked
or have a bluish tinge.
• The rinse aid dosage is too high.
The crockery has not been dried
properly.
• A wash cycle without a drying programme has been selected.
• The rinse aid has been used up or the dosage is too low (see Rinse aid and salt).
• The rinse aid dispenser setting is not high enough.
• The crockery is made from non-stick material or plastic.
The dishes are not clean.
• The racks are overloaded (see Loading the racks).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles).
• Excessive foam presence: the detergent has not been measured out correctly or it is not
suitable for use in dishwashers. (see Start-up and use).
• The lid on the rinse aid compartment has not been shut correctly.
• The lter is dirty or blocked (see Care and maintenance).
• The rened salt level is low (see Rinse aid and salt).
The dishwasher does not take any
water in - Tap shut-off alarm
(beeps are heard and H appears for
some minutes on the display)
(the ON/OFF indicator light ashes and
number 6 appears on the display).
• There is no water in the mains supply.
• The water inlet hose is bent (see Installation).
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken when the beeps sounded.
Switch off the machine using the ON/OFF button, turn on the tap and switch the machine back
on after a few seconds by pressing the same button. Re-program the appliance and restart the
wash cycle.
Mode d’emploi
LAVE-VAISSELLE
Sommaire
Fiche de produit, 16
Précautions et conseils, 17-18
Sécurité générale
Mise au rebut
Economies et respect de l’environnement
Installation et Assistance, 19-20
Mise en place et mise à niveau
Raccordements eau et électricité
Caractéristiques techniques
Conseils pour le premier lavage
Assistance
Description de l’appareil, 21
Vue d’ensemble
Tableau de bord
Charger les paniers, 22-23
Panier inférieur
Panier supérieur
Panier à couverts
Plateau range-couverts
Réglage du panier supérieur
Mise en marche et utilisation, 24
Mettre en marche le lave-vaisselle
Charger le produit de lavage
Programmes, 25
Tableau des programmes
Programmes spéciaux et Options, 26
Produit de rinçage et sel régénérant, 27
Charger le produit de rinçage
Charger le sel régénérant
Entretien et soin, 28
Coupure de l’arrivée d’eau et du courant
Nettoyer le lave-vaisselle
Eviter les mauvaises odeurs
Nettoyer les bras de lavage
Nettoyage du filtre d’entrée d’eau
Nettoyer les filtres
En cas d’absence pendant de longues périodes
Anomalies et remèdes, 29
LTF 8B116
Français, 15
FR
16
FR
Fiche de produit
Marque
HOTPOINT ARISTON
Modèle
LTF 8B116
Capacité nominale dans un environnement standard (1)
13
Classe énergétique sur une échelle de A+++ (faible consommation) à D (consommation élevée)
A+
Consommation d''énergie par année en kWh (2)
293.0
Consommation d''énergie du cycle de lavage standard en kWh
1.03
Consommation d''energie en mode "off" en W
0.5
Consommation d''energie en mode "on" en W
5.0
Consommation d''eau par an en litres (3)
3080.0
Classe d’efcacité du séchage sur une échelle de G (efcacité minimum) à A (efcacité maximum)
A
Durée du programme pour un cycle de lavage standard en minutes
190’
Durée du mode "on" en minutes
10
Émissions acoustiques dans l’air, exprimées en dB(A) re 1 pW
46
Encastrable
Oui
Remarque
1) Les informations sur l’étiquette et sur la che se rapportent au cycle de lavage standard. Ce programme convient pour laver une
vaisselle normalement sale, et il s’agit des programmes les plus efcaces en termes de consommation combinée d’eau et d’énergie. Le
cycle de lavage standard correspond au cycle éco.
2) Sur la base de 280 cycles de lavage standard avec une alimentation en eau froide et une consommation en modes à faible
puissance. La consommation réelle d’énergie dépend des conditions d’utilisation de l’appareil.
3) Sur la base de 280 cycles de lavage standard. La consommation réelle d’énergie dépend des conditions d’utilisation de l’appareil.
Fiche de produit
FR
17
* Présent uniquement sur certains modèles.
Précautions et conseils
Cet appareil a été conçu et fabriqué
conformément aux normes internationales de
sécurité. Ces consignes sont fournies pour des
raisons de sécurité, il faut les lire attentivement.
Conserver ce mode d’emploi pour pouvoir le
consulter à tout moment. En cas de vente, de
cession ou de déménagement, s’assurer qu’il
accompagne bien l’appareil.
Lire attentivement les instructions : elles fournissent
des conseils importants sur l’installation, l’utilisation
et la sécurité de l’appareil.
Cet appareil est conçu pour un usage domestique
ou autres applications similaires, telles que :
- lieux aménagés en espace cuisine pour le
personnel de magasins, bureaux et autres lieux
de travail ;
- fermes ;
- utilisation par les clients d’hôtels, de motels ou
autres locaux de type résidentiel ;
- chambres d’hôtes.
Sécurité générale
• Cetélectroménagern'est pas destiné à être
utilisé par des personnes (enfants compris)
dont les capacités physiques, sensorielles ou
mentales sont réduites ou qui ne disposent
pasdesconnaissancesoudel'expérience
nécessaires, à moins qu'elles n'aient été
forméesetencadréespourl'utilisationdecet
appareil par une personne responsable de leur
sécurité.
• Lesenfantsdoiventêtresurveillésparunadulte
pour éviter qu’ils ne jouent avec l’appareil.
• Cetappareilestconçupourunusagedetype
nonprofessionnelàl'intérieurd'unehabitation.
• Cetappareilestdestinéaulavagedevaisselleà
usagedomestique,ilnedoitêtreutiliséquepar
des adultes et selon les instructions reportées
dans cette notice.
• Nepasinstallerl’appareilàl’extérieur,même
dansunendroitprotégé,carilestextrêmement
dangereux de l’exposer à la pluie et aux orages.
• Nepastoucheraulave-vaissellepiedsnus.
• Nejamaistirersurlecâblepourdébrancherla
fiche de la prise de courant.
• Fermerlerobinetdel’eauetdébrancherlafiche
de la prise de courant avant d’effectuer tous
travaux de nettoyage et d’entretien.
• Encasdepanne,éviteràtoutprixd’accéder
aux mécanismes internes pour tenter une
réparation.
• Ne pas s’appuyer à la porte ouverte ou s’y
asseoir : l’appareil pourrait basculer.
• Nepasgarderlaporteouvertepouréviterde
buter contre elle en risquant de se faire mal.
• Garderlesproduits delavageet derinçage
hors de la portée des enfants.
• Lesemballagesnesontpasdesjouetspourenfants.
Mise au rebut
• Mise au rebut du matériel d’emballage : se
conformer aux réglementations locales de
manièreàcequelesemballagespuissentêtre
recyclés.
• La directive européenne 2012/19/EU sur
les déchets d’équipements électriques
et électroniques (DEEE), prévoit que les
électroménagers ne peuvent pas être traités
comme des déchets solides urbains normaux.
Lesappareils usagés doivent être collectés
séparément afin d’optimiser le taux de
récupération et le recyclage des matériaux
qui les composent et réduire l’impact sur la
santé humaine et l’environnement Le symbole
de la poubelle barrée est appliqué sur tous les
produits pour rappeler qu’ils font l’objet d’une
collecte sélective.
Pour tout autre renseignement sur la collecte
des électroménagers usés, prière de s’adresser
au service public préposé ou au vendeur.
Economies et respect de l’environnement
Faire des économies d’eau et d’électricité
• Nefairefonctionnerlelave-vaissellequequand
il est rempli au maximum de sa capacité.
Dans l’attente de remplir l’appareil, lancer le
cycle de Trempage pour éviter la formation de
mauvaises odeurs
(voir Programmes)
.
• Sélectionnerunprogrammeadaptéautypede
vaisselle et à son degré de salissure, consulter
pour cela le Tableau des programmes :
- pour de la vaisselle normalement sale, choisir
le programme Eco (économique), il limite la
quantité d’eau et d’électricité utilisée.
- pour une quantité réduite de vaisselle, choisir
l’option Demi-charge
*
(voirMiseenmarcheet
utilisation).
• Silecontratdefournitured’électricitéprévoit
des tranches horaires à prix réduit, effectuer
les lavages pendant ces heures creuses.
L’option Départ différé
*
(voirMiseenmarche
et utilisation)
peut vous aider à organiser vos
lavages dans ce sens.
18
FR
Produits de lavage sans phosphates, sans
chlore et aux enzymes
• Ilestvivementconseilléd’utiliserdesproduits
de lavage sans phosphates et sans chlore, plus
indiqués pour la protection de l’environnement.
•Les enzymes développent une action
particulièrement efficace à des températures
avoisinant50°C,lesproduitsdelavageaux
enzymespermettentdoncdesélectionnerdes
lavages à de basses températures et d’obtenir
lesmêmesrésultatsqu’àunetempératurede
65°C.
• Pour bien doser le produit de lavage, il faut
tenir compte des indications du fabricant, de
la dureté de l’eau, de la quantité de vaisselle
et de son degré de salissure pour éviter tout
gaspillage. Bien que biodégradables, les
produits de lavage contiennent des éléments
qui altèrent l’équilibre de la nature.
FR
19
* Présent uniquement sur certains modèles.
En cas de déménagement, transporter l’appareil
verticalement; si besoin est, l’incliner sur le dos.
Mise en place et mise à niveau
1.Déballerl’appareilets’assurerqu’iln’apasétéendommagé
pendantle transport. S’il est abîmé, nepas leraccorder et
contacter le revendeur.
2.Installerlelave-vaisselledemanièreàcequelescôtéset
la paroi arrière touchent aux meubles adjacents ou au mur.
L’appareilpeutêtreencastrésousunplandetravailcontinu
*
(voir feuille de montage)
.
3.Installerlelave-vaissellesurunsolplatetrigide.Compenser
les irrégularités en vissant ou en dévissant les pieds avant
jusqu'àce que l'horizontalité de l’appareil soit parfaite.Une
bonnehorizontalitégarantitlastabilitédel’appareiletsupprime
tout risque de vibrations, bruits et déplacements.
4
*. Pour régler la hauteur du pied arrière, agir sur la douille rouge
à six pans située dans la partie avant du lave-vaisselle, en bas
etaumilieu,àl’aided’uneclémâleàsixpans,ouverture8mm.
Tourner dans le sens des aiguilles d’une montre pour augmenter
la hauteur et dans le sens inverse pour la diminuer.
(voir feuille
d’instructions jointe à la documentation)
Raccordements eau et électricité
L’adaptation des installations électriques et les travaux de
plomberiede l’installation doiventêtre effectuéspar du
personnel qualifié.
Lelave-vaissellenedoitpasécraserlestuyauxoulecâble
d’alimentation électrique.
Utiliserdestuyauxneufspoureffectuerleraccordementde
l’appareil au réseau de distribution de l’eau.
Nepasréutiliserlesancienstuyaux.
Lestuyaux d’amenée et d’évacuation del’eau et lecâble
d’alimentationélectriquepeuventêtreorientésversladroiteou
vers la gauche pour simplifier l’installation.
Raccord du tuyau d’amenée de l’eau
• Auneprised'eaufroide:bienvisserletuyaud’amenéeà
unrobinet à embout fileté 3/4gaz;avantde visser, faire
couler l’eau jusqu’à ce quelle devienne limpide et dépourvue
d’impuretés qui pourraient engorger l’appareil.
• Auneprised'eauchaude:encasd’installationdechauffage
centralisé(radiateurs),lelave-vaissellepeutêtrealimenté
avecdel’eauchaudederéseaunedépassantpas60°C.
Visser le tuyau au robinet en procédant comme pour la prise
d'eaufroide.
Silalongueurdutuyaud’amenéenesuffitpas,s’adresser
à un magasin spécialisé ou à un technicien agréé
(voir
Assistance)
.
Lapressiondel’eaudoitêtrecompriseentrelesvaleurs
reportées dans le tableau des Caractéristiques techniques
(voir
ci-contre)
.
Attentionàcequeletuyaunesoitpaspliéouécrasé.
Raccordement du tuyau d’évacuation de l’eau
Raccorder le tuyau d’évacuation, sans le plier, à une conduite
d’évacuation ayant au moins 4 cm de diamètre.
Letuyaud’évacuationdoitêtreplacéentre40et80cm au-
dessusdusoloudupland’appuidulave-vaisselle(A).
Avantderaccorderletuyaud’évacuationdel’eauausiphonde
l’évier, retirer le bouchon en plastique (B).
Sécurité anti-fuite
Pour éviter tout risque d’inondation, le lave-vaisselle :
- est équipé d’un dispositif qui coupe l’arrivée de l’eau en cas
d’anomalie ou de fuite à l’intérieur de l’appareil.
Quelques modèles sont équipés d’un dispositif de sécurité
supplémentaire New Acqua Stop
*, qui garantit contre tout
risqued'inondationmêmeencasderupturedutuyaud’amenée
de l’eau.
ATTENTION : TENSION DANGEREUSE !
Ilnefautenaucuncascouperletuyaud’amenéedel’eaucar
il contient des parties sous tension.
Raccordement électrique
Avantdebrancherlafichedanslaprisedecourant,s'assurer
que :
• la prise estbien reliéeà laterre etest conformeaux
réglementations en vigueur ;
• lapriseestbienapteàsupporterlapuissancemaximalede
la machine reportée sur la plaquette signalétique fixée à la
contre-porte
(voir chapitre Description du lave-vaisselle) ;
• atensiond’alimentationestbiencompriseentrelesvaleurs
figurant sur la plaque signalétique de la contre-porte ;
• la prise estbien compatibleavec lafiche del’appareil.
Autrement,faireremplacerlaficheparuntechnicienagréé
(voirAssistance)
; n’utiliser ni rallonges ni prises multiples.
Aprèsinstallation de l’appareil,le câbled’alimentation
électriqueet la prise decourant doivent êtrefacilement
accessibles.
Lecâblenedoitêtrenipliénitropécrasé.
Afind’éviter tout danger, fairechanger lecordon
d’alimentationabîmé,parlefabricantouparsonserviceaprès-
vente.
(VoirAssistance)
Installation et Assistance
20
FR
Caractéristiques techniques
Dimensions
largeur 59,5 cm
hauteur 82 cm
profondeur 57 cm
Capacité 13 couverts standard
Pression eau
d’alimentation
0,05 ÷ 1 MPa (0,5 ÷ 10 bar)
7,25 – 145 psi
Tension
d’alimentation
Voir étiquette des caractéristiques
Puissance totale
absorbée
Voir étiquette des caractéristiques
Fusible Voir étiquette des caractéristiques
Cet appareil est conforme aux
Directives Communautaires suivantes:
- 2006/95/EC (Basse Tension)
- 2004/108/EC (Compatibilité
Electromagnétique)
-2009/125/EC (Comm. Reg.
1016/2010) (Ecodesign)
-97/17/EC (Etiquetage)
-2012/19/EU (DEEE)
Ruban anti-condensation*
Aprèsavoirencastrélelave-vaisselle,ouvrirlaporteetcollerle
ruban adhésif transparent sous le plan en bois pour le protéger
contre la formation de condensation.
Conseils pour le premier lavage
Aprèsl’installation,enleverleschevillesplacéessurlespaniers
et les élastiques de blocage sur le panier supérieur (le cas
échéant).
Juste avant le premier lavage, remplir complètement d’eau le
réservoiràseletajouterenviron1kgdesel(voirProduitde
rinçage et sel régénérant) : il est tout à fait normal que de l’eau
déborde.Sélectionnerledegrédeduretédel’eau(voirProduit
derinçageetselrégénérant).-Aprèsremplissageduréservoir
àsel,levoyantSEL*s’éteint.
Le manque de remplissage du réservoir à sel, peut
endommager l’adoucisseur d’eau et l’élément chauffant.
Cet électroménager dispose de signaux sonores/bips
(selon
le modèle de lave-vaisselle
) qui signalent que la commande
a été activée: allumage, fin de cycle etc..
Tous les symboles/voyants/led lumineux du bandeau de
commande/afficheur peuvent avoir des couleurs différentes,
flasher ou être en fixe.
(selon le modèle de lave-vaisselle)
.
Affichage d'informations utiles concernant le type de cycle
sélectionné, la phase de lavage/séchage, le temps résiduel,
la température etc.... etc...
Avant d’appeler le service d’assistance
technique:
• Vérifier s’ilest possible de résoudre l’anomaliesoi-
même
(voirAnomaliesetremèdes).
• Faire repartirle programmepour s’assurerque
l’inconvénient a été résolu.
• Sicen’estpaslecas,contacterunServiced’Assistance
Technique agréé.
Ne jamais faire appel à des techniciens non agréés.
Communiquer:
• letyped’anomalie;
• lemodèledel’appareil(Mod.);
• lenumérodesérie(S/N).
Ces informations figurent sur la plaque signalétique
apposée sur l’appareil
(voir Description de l’appareil).
Service
* Présent uniquement sur certains modèles.
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Hotpoint LTF 8B116 EU Mode d'emploi

LTF 8B116 EU
Hotpoint
Marque
Hotpoint
Modèle
LTF 8B116 EU
Catégorie
Lave-vaisselle
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents