Kenmore Elite 75223 Guide d'installation

Catégorie
Cuisinières
Taper
Guide d'installation
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2C3
www.sears.ca
Kenmore Elite®
P/N W11024188A
Gas Range
Estufa a gas
Cuisinière à gaz
Installation Instructions
Instrucciones de instalación
Instructions d’installation
English/Español/Français
IMPORTANT:
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
IMPORTANTE:
Instalador: Deje las instrucciones de instalación con el propietario.
Propietario: Conserve las instrucciones de instalación para referencia futura.
IMPORTANT :
Installateur : Remettre les instructions d’installation au propriétaire.
Propriétaire : Conserver les instructions d’installation pour référence ultérieure.
2
RANGE SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch.
Do not use any phone in your building.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
TABLE OF CONTENTS
RANGE SAFETY ....................................................................2
INSTALLATION REQUIREMENTS
..........................................4
Tools and Parts
.................................................................................4
Location Requirements
...................................................................4
Electrical Requirements
..................................................................6
Gas Supply Requirements
.............................................................. 6
INSTALLATION INSTRUCTIONS
........................................... 8
Unpack Range
.................................................................................8
Install Anti-Tip Bracket
...................................................................8
Adjust Leveling Legs
.......................................................................9
Level Range
....................................................................................10
Make Gas Connection
..................................................................10
Verify Anti-Tip Bracket IsInstalledandEngaged
..................... 11
Electronic Ignition System
.............................................................11
Remove/Replace Drawer
............................................................. 12
Oven Door...................................................................................... 12
Complete Installation
.................................................................... 13
GAS CONVERSIONS
.......................................................... 14
Propane Gas Conversion
..............................................................14
Natural Gas Conversion
...............................................................17
Adjust Flame Height
.................................................................... 20
3
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking appliance. This type of
ventilation system may cause ignition and combustion problems with this gas cooking appliance resulting in personal injury or
unintended operation.
In the State of Massachusetts, the following installation instructions apply:
Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
If using a ball valve, it shall be a T-handle type.
A flexible gas connector, when used, must not exceed 3 feet (91.4 cm).
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation instructions.
Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
Anti-Tip
Bracket
To verify the anti-tip bracket is installed and engaged:
Slide range forward.
Look for the anti-tip bracket securely attached to floor or wall.
Slide range back so rear range foot is under anti-tip bracket.
See installation instructions for details.
Range Foot
WARNING
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listedhere.
Tools Needed
Parts Supplied
Check that all parts are included.
Propane/Natural Gas Conversion Kit
#10 x 1
5
/
8
" (4.1 cm) screws
(for mounting anti-tipbracket)(2)
Anti-tip bracket (inside oven cavity)
Anti-tip bracket must be securely mounted to the back wall
or floor. Thickness of flooring may require longer screws
to anchor bracket to subfloor. Longer screws are available
from your local hardware store.
Parts Needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See the “Electrical Requirements”
and “Gas Supply Requirements” sections.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Donot obstruct ow of combustion and ventilation air.
It is the installer’s responsibility to comply with installation
clearances specied on the model/serial/rating plate. The
model/serial/rating plate is located behind the oven door
on the top left-hand side of the oven frame.
The range should be located for convenient use in the
kitchen.
Recessed installations must provide complete enclosure
ofthe sides and rear of the range.
All openings in the wall or oor where range is to be
installed must be sealed.
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see the “Install Anti-Tip
Bracket” section.
Grounded electrical supply is required. See the “Electrical
Requirements” section.
Proper gas supply connection must be available. See the
“Gas Supply Requirements” section.
Contact a qualied oor covering installer to check that the
oor covering can withstand at least 200°F (93°C).
Use an insulated pad or 1/4" (0.64 cm) plywood under
range if installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check
with your builder or cabinet supplier to make sure that the
materials used will not discolor, delaminate, or sustain other
damage. This oven has been designed in accordance with the
requirements of UL and CSA International and complies with
the maximum allowable wood cabinet temperatures of 194°F
(90°C).
Tape measure
Phillips screwdriver
Flat-blade screwdriver
1/8" (3 mm) at-blade
screwdriver
Level
Drill
Wrench or pliers
Pipe wrench
15/16" (2.4 cm)
combination wrench
1/8" (3.2 mm) drill bit
(forwood oors)
Marker or pencil
Pipe-joint compound
resistant to propane gas
3/16" (4.8 mm)
carbide-tipped masonry
drill bit (for concrete/
ceramic oors)
Noncorrosive leak-
detection solution
For Propane/Natural Gas
Conversions
5/8" (1.6 cm)
combination wrench
3/8" (1 cm) nut driver
9/32" (7 mm) nut driver
Masking tape
5
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the
Manufactured Home Construction and Safety Standard,
Title24 CFR, Part 3280 (formerly the Federal Standard for
Mobile Home Construction and Safety, Title 24, HUD Part
280). When such standard is not applicable, use the Standard
for Manufactured Home Installations, ANSI A225.1/NFPA 501A
or local codes.
In Canada, the installation of this range must conform with
thecurrent standards CAN/CSA - A240-latest edition or with
local codes.
Mobile Home Installations Require:
When this range is installed in a mobile home, it must be
secured to the oor during transit. Any method of securing
the range is adequate as long as it conforms to the
standards listed above.
Product Dimensions
This manual covers several models. Your model may appear
dierent from the models depicted. Dimensions given are
maximum dimensions across all models.
IMPORTANT: Range must be level after installation. Follow the
instructions in the “Level Range” section. Using the cooktop as
a reference for leveling the range is not recommended.
* Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth, and
36"(91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood
combination above the range, follow the range hood or
microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
Range may be installed next to combustible walls with zero
clearance.
NOTE: 24" (61.0 cm) minimum when bottom of wood or
metal cabinet is shielded by not less than 1/4" (0.64 cm)
ame-retardant millboard covered with not less than No.28
MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024"
(0.6mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the
cooking platform and the bottom of an uncovered wood
ormetal cabinet.
A
B
D
E
F
C
A. 1
3
/
16
" (3.0 cm) height from
cooktop to top of vent
B. 29
7
/
8
" (75.9 cm)
C. Model/serial/rating plate
(located behind the oven
door on the top left-hand
side of the oven frame)
D. 36" (91.4 cm) height to
top of cooktop edge with
leveling legs screwed in all
the way*
E. 28
25
/
64
" (72.1 cm) max.
depth from front of console
to back of range
F. 29
1
/
64
" (73.7 cm) max.
depth from handle to back
of range
M
A
B
C
D
E
F
H
I
J
L
K
G
A. 18" (45.7 cm) upper side cabinet to countertop
B. 13" (33 cm) max. upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to top of cooktop, see NOTE.
E. 30" (76.2 cm) min. opening width
F. 3" (7.6 cm) min. clearance from both sides of range to side wall
orother combustible material
G. The shaded area is recommended for installation of rigid gas pipe
and grounded outlet.
H. 13
1
/
8
" (33.3 cm)
I. 7
11
/
16
" (19.5 cm)
J. 4
13
/
16
" (12.2 cm)
K. 3
11
/
16
" (9.4 cm)
L. 12" (30.5 cm)
M. Cabinet door or hinges should not extend into the cutout.
6
Electrical Requirements
IMPORTANT: The range must be electrically grounded in
accordance with local codes and ordinances, or in the absence
of local codes, with the National Electrical Code, ANSI/NFPA
70 or Canadian Electrical Code, CSA C22.1.
This range is equipped with an electronic ignition system that
will not operate properly if plugged into an outlet that is not
properly polarized.
If codes permit and a separate ground wire is used, it is
recommended that a qualied electrical installer determine
that the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
A 120-volt, 60 Hz., AC-only, 15-amp fused, grounded, and
polarized electrical circuit is required. A time-delay fuse
or circuit breaker is also recommended. It is recommended
that a separate circuit serving only this range be provided.
Electronic ignition systems operate within wide voltage
limits, but proper grounding and polarity are necessary.
Check that the outlet provides 120-volt power and is
correctly grounded.
This gas range is not required to be plugged into a GFCI
(Ground-Fault Circuit Interrupter) outlet. It is recommended
that you not plug an electric spark ignition gas range or
any other major appliance into a GFCI wall outlet as it
maycause the GFCI to trip during normal cycling.
Performance of this range will not be aected if operated
on a GFCI-protected circuit. However, occasional nuisance
tripping of the GFCI breaker is possible due to the normal
operating nature of electronic gas ranges.
The tech sheet and wiring diagram are located on the back
of the range in a plastic bag.
NOTE: The metal chassis of the range must be grounded
in order for the control panel to work. If the metal chassis
of the range is not grounded, no keypads will operate.
Check with a qualified electrician if you are in doubt as
towhether the metal chassis of the range is grounded.
Gas Supply Requirements
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local
codes and ordinances. In the absence of local codes,
installation must conform with American National Standard,
National Fuel Gas Code ANSI Z223.1 - latest edition or
CAN/CGA B149 - latest edition.
IMPORTANT: Leak testing of the range must be conducted
according to the manufacturer’s instructions.
Type of Gas
Natural Gas:
This range is factory set for use with Natural gas. See the “Gas
Conversions” section. The model/serial/rating plate located on
the oven frame behind the top left-hand side of the oven door
has information on the types of gas that can be used. If the
types of gas listed do not include the type of gas available,
check with the local gas supplier.
Propane Conversion:
Conversion must be done by a qualied service technician.
No attempt shall be made to convert the appliance from the
gas specied on the model/serial/rating plate for use with a
dierent gas without consulting the serving gas supplier. See
the “Gas Conversions” section.
Gas Supply Line
Provide a gas supply line of 3/4" (1.9 cm) rigid pipe to
the range location. A smaller size pipe on longer runs
may result in insucient gas supply. With propane,
piping or tubing size can be 1/2" (1.3 cm) minimum.
Usually, propane suppliers determine the size and materials
used in the system.
NOTE: Pipe-joint compounds that resist the action of
propane must be used. Do not use TEFLON
®†
tape.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make
sure gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
®
TEFLON is a registered trademark of Chemours.
7
Flexible Metal Appliance Connector:
If local codes permit, a new CSA design-certied,
4to5 ft (122 to 152.4 cm) long, 1/2" or 3/4"
(1.3or1.9cm) I.D. (inside diameter), exible metal
appliance connector may be used for connecting
rangeto the gassupply line.
A 1/2" (1.3 cm) male pipe thread is needed for
connection to the female pipe threads of the
inlettotheappliance pressure regulator.
Do not kink or damage the exible metal tubing
whenmoving the range.
Must include a shut-o valve:
The supply line must be equipped with a manual shut-off
valve. This valve should be located in the same room but
external to the range opening, such as an adjacent cabinet.
It should be in a location that allows ease of opening and
closing. Do not block access to shut-off valve. The valve is
for turning on or shutting off gas to the range.
Gas Pressure Regulator
The gas pressure regulator supplied with this range must be
used. The inlet pressure to the regulator should be as follows
for proper operation:
Natural Gas:
Minimum pressure: 6" WCP
Maximum pressure: 14" WCP
Propane:
Minimum pressure: 11" WCP
Maximum pressure: 14" WCP
Contact local gas supplier if you are not sure about the inlet
pressure.
Burner Input Requirements
Input ratings shown on the model/serial/rating plate are for
elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings are reduced
at a rate of 4% for each 1,000 ft (304.8 m) above sea level
(not applicable for Canada).
Gas Supply Pressure Testing
Gas supply pressure for testing regulator must be at least 1"
water column pressure above the manifold pressure shown on
the model/serial/rating plate.
Line Pressure Testing Above 1/2 psi Gauge (14" WCP)
The range and its individual shut-o valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
1/2 psi (3.5 kPa).
Line Pressure Testing at 1/2 psi Gauge (14" WCP) or Lower
The range must be isolated from the gas supply piping
system by closing its individual manual shut-o valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psi (3.5 kPa).
A
B
C
A. Gas supply line
B. Shut-off valve open position
C. To range
8
INSTALLATION INSTRUCTIONS
Unpack Range
1. Remove shipping materials, tape, and lm from the range.
Keep cardboard bottom under range. Do not dispose of
anything until the installation is complete.
2. Remove oven racks and parts package from oven and
shipping materials.
3. To remove cardboard bottom, rst take 4 cardboard
corners from the carton. Stack one cardboard corner on
top of another. Repeat with the other 2 corners. Place them
lengthwise on the oor behind the range to support the
range when it is laid on its back.
4. Using 2 or more people, rmly grasp the range and gently
lay it on its back on the cardboard corners.
5. Remove cardboard bottom.
The leveling legs can be adjusted while the range is on its
back. See the “Adjust Leveling Legs” section.
NOTE: To place range back up into a standing position, put a
sheet of cardboard or hardboard on the oor in front of range
to protect the ooring. Using 2 or more people, stand range
back up onto the cardboard or hardboard.
Install Anti-Tip Bracket
1. Remove the anti-tip bracket from the inside of the oven.
2. Determine which mounting method to use: oor or wall.
If you have a stone or masonry floor, you can use the
wallmounting method. If you are installing the range in
amobile home, you must secure the range to the floor.
This anti-tip bracket and screws can be used with wood
ormetal studs.
3. Determine and mark centerline of the cutout space. The
mounting bracket can be installed on either the left-hand
orright-hand side of the cutout. Position mounting bracket
against the wall in the cutout so that the V-notch of the
bracket is 12
1
/
2
" (31.8 cm) from centerline, as shown.
WARNING
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
Centerline
A
B
A. 12
1
/
2
" (31.8 cm)
B. Bracket V-notch
9
4. Drill two 1/8" (3 mm) holes that correspond to the
bracket holes of the determined mounting method.
See the following illustrations.
Floor Mounting
Rear position Front position Diagonal (2 options)
Wall Mounting
5. Using the two #10 x 1
5
/
8
" (4.1 cm) Phillips-head screws
provided, mount anti-tip bracket to the wall or oor.
6. Move range close enough to opening to allow for nal
electrical connections. Remove shipping base, cardboard,
or hardboard from under range.
7. Move range into its nal location, making sure rear leveling
leg slides into anti-tip bracket.
8. Move range forward onto shipping base, cardboard,
or hardboard to continue installing the range, using the
following installation instructions.
Adjust Leveling Legs
1. If range height adjustment is necessary, use a wrench
orpliers to loosen the 4 leveling legs.
This may be done with the range on its back or with the
range supported on 2 legs after the range has been placed
back to a standing position.
NOTE: To place range back up into a standing position, put
a sheet of cardboard or hardboard in front of range. Using
2 or more people, stand range back up onto the cardboard
or hardboard.
2. Measure the distance from the top of the counter to the
oor.
3. Measure the distance from the top of the cooktop to the
bottom of the leveling legs. This distance should be the
same. If it is not, adjust the leveling legs to the correct
height. The leveling legs can be loosened to add up to
a maximum of 1" (2.5 cm). A minimum of 3/16" (5 mm)
isneeded to engage the anti-tip bracket.
NOTE: If height adjustment is made when range is standing,
tilt the range back to adjust the front legs, and then tilt
forward to adjust the rear legs.
4. When the range is at the correct height, check that there
is adequate clearance under the range for the anti-tip
bracket. Before sliding range into its nal location, check
that the antitip bracket will slide under the range and onto
the rear leveling leg prior to anti-tip bracket installation.
NOTE: If a Trim Kit will be used, the top of the cooktop
should be higher than the counter. See the Installation
Instructions included with the Trim Kit for the correct height.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
10
Level Range
1. Place level on the oven bottom, as indicated in one of the
2gures below, depending on the size of the level. Check
with the level side to side and front to back.
2. If range is not level, use a wrench or pliers to adjust leveling
legs up or down until the range is level.
Make Gas Connection
This range is factory set for use with Natural gas. To use this
range with propane, see the “Gas Conversions” section before
connecting this range to the gas supply. Gas conversions from
Natural gas to propane or from propane to Natural gas must
be done by a qualied installer.
Typical Flexible Connection
1. Apply pipe-joint compound made for use with propane to
the smaller thread ends of the exible connector adapters.
See B and G in the following illustration.
2. Attach 1 adapter to the gas pressure regulator and the
other adapter to the gas shut-o valve. Tighten both
adapters, being certain not to move or turn the gas
pressureregulator.
3. Use a 15/16" (2.4 cm) combination wrench and an
adjustable wrench to attach the exible connector to
the adapters.
IMPORTANT: All connections must be wrench-tightened. Do
not make connections to the gas regulator too tight. Making
the connections too tight may crack the regulator and
cause a gas leak. Do not allow the regulator to turn when
tightening fittings.
Complete Connection
1. Check that the gas pressure regulator shut-o valve
isintheOn position.
2. Open the manual shut-o valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.
3. Test all connections by brushing on an approved
noncorrosive leak-detection solution. If bubbles appear,
aleak is indicated. Correct any leak found.
4. Remove cooktop burner caps and bases from package
containing parts.
5. Align the gas tube opening in the burner base with the
orice holder on the cooktop and the igniter electrode
withthe notch in the burner base.
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make
sure gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
A
B
C
D
E
FG
H
A. Gas pressure regulator
B. Use pipe-joint compound.
C. Adapter (must have 1/2"
[1.3cm] male pipe thread)
D. Flexible connector
E. Manual gas shut-off valve
F. 1/2" (1.3 cm) or 3/4" (1.9 cm)
gas pipe
G. Use pipe-joint compound.
H. Adapter
A
A. Gas pressure regulator shut-off
valve shown in the On position
A
B
A. Closed valve
B. Open valve
11
6. Place the burner caps on the appropriate burner bases.
IMPORTANT: The bottom of the small and medium caps
are different. Do not put the wrong size burner cap on the
burner base. Each round burner cap is marked with an S,
M, L, or XL to match with a letter on the burner base.
Burner caps should be level when properly positioned. If
burner caps are not properly positioned, surface burners
will not light. The burner cap should not rock or wobble
when properly aligned.
7. Plug into a grounded 3 prong outlet.
Verify Anti-Tip Bracket
IsInstalledandEngaged
1. Slide range into nal location, making sure rear leveling
legslides into anti-tip bracket.
2. Remove the storage drawer. See the “Remove/Replace
Drawer” section.
3. Use a ashlight to look underneath the bottom of
therange.
4. Visually check that the rear range foot is inserted into
theslot of the anti-tip bracket.
Electronic Ignition System
Initial Lighting and Gas Flame Adjustments
Cooktop and oven burners use electronic igniters in place of
standing pilots. When the cooktop control knob is turned to
the Lite position, the system creates a spark to light the burner.
All cooktop burners will spark, but only the burner with the
control knob turned to the Lite position will produce a ame.
This sparking continues as long as the control knob is turned
totheLite position.
When the oven control is turned to the desired setting,
sparking occurs and ignites the gas.
Check Operation of Cooktop Burners
Standard Surface Burners
Push in and turn each control knob to the Lite position.
The ame should light within 4 seconds. The rst time a burner
is lit, it may take longer than 4 seconds to light because of air
in the gas line.
If Burners Do Not Light Properly:
Turn cooktop control knob to the O position.
Check that the range is plugged into a grounded 3 prong
outlet. Check that the circuit breaker has not tripped or
thehousehold fuse has not blown.
Check that the gas shut-o valves are set to the open
position.
Check that burner caps are properly positioned on burner
bases.
Repeat startup. If a burner does not light at this point, turn the
control knobs to the O position and contact your dealer or
authorized service company for assistance. Please reference
the back cover of the Use & Care Guide to contact service.
If the cooktop low burner ame needs to be adjusted for any
of the burners, see the “Adjust Flame Height” section.
A
B
C
D
E
A. Burner cap
B. Gas tube opening
C. Burner base
D. Igniter electrode
E. Orifice holder
Small cap
Medium cap
Large cap X-large cap
A
B
A. Incorrect
B. Correct
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
12
Check Operation of Oven Bake Burner
1. Press BAKE.
2. Press the Start keypad.
The oven burner should light within 8 seconds. The first
timea burner is lit, it may take longer than 8 seconds
tolight because of air in the gas line.
3. After 2 minutes, open the oven door and check that the
oven is warm.
If Burner Does Not Light Properly:
Press the Cancel keypad.
Check that the range is plugged into a grounded 3 prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
Check that the gas shut-o valves are set to the open
position.
Repeat steps 1 through 3. If the burner does not light at this
point, press the Cancel keypad and contact your dealer or
authorized service company for assistance. Please reference
the back cover of the Use & Care Guide to contact service.
If the bake burner ame needs to be adjusted, see the “Adjust
Flame Height” section.
Refer to the Use & Care Guide for proper operation of the
oven controls.
Check Operation of Oven Broil Burner
1. Close the oven door.
2. Press BROIL.
3. Press the Start keypad.
The oven burner should light within 8 seconds. The first time
a burner is lit, it may take longer than 8 seconds to light
because of air in the gas line.
4. After 2 minutes, open the oven door and check that the
oven is warm.
If Burner Does Not Light Properly:
Press the Cancel keypad.
Check that the range is plugged into a grounded 3 prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
Check that the gas shut-o valves are set to the open
position.
Repeat steps 1 to 3. If the burner does not light at this
point, press the Cancel keypad and contact your dealer or
authorized service company for assistance. Please reference
the back cover of the Use & Care Guide to contact service.
If the broil burner ame needs to be adjusted, see the “Adjust
Flame Height” section.
Refer to the Use & Care Guide for proper operation of the
oven controls.
Remove/Replace Drawer
Remove all items from inside the storage drawer, and then
allow the range to cool completely before attempting to
remove the drawer.
To Remove:
1. Open the drawer to its fully open position.
2. Raise the front edge and then lift out.
To Replace:
1. Align the forward drawer notches with the notches in the
drawer rails on both sides. Place the rear alignment tabs
into the drawer rails on both sides.
2. Push the drawer in all the way.
3. Gently open and close the drawer to ensure it is seated
properly on the rails on both sides.
Oven Door
For normal range use, it is not suggested to remove the oven
door. However, if removal is necessary, make sure the oven
iso and cool. Then, follow these instructions. The oven door
is heavy.
To Remove:
1. Open oven door all the way.
2. Pinch the hinge latch between 2 ngers and pull forward.
Repeat on other side of oven door.
3. Close the oven door as far as it will shut.
4. Lift the oven door while holding both sides.
Continue to push the oven door closed and pull it away
from the oven doorframe.
A
A. Hinge latch
13
To Replace:
1. Insert both hanger arms into the door. Be sure that the hinge
notches are engaged in the oven doorframe.
2. Open the oven door.
The door should be able to open all the way.
3. Move the hinge levers back to the locked position.
Checkthat the door is free to open and close and is
levelwhile closed. If it is not, repeat the removal and
installation procedures.
Complete Installation
1. Check that all parts are now installed. If there is an
extrapart, go back through the steps to see which step
wasskipped.
2. Check that you have all of your tools.
3. Check that you have all of the range accessories,
especiallyoven racks. These accessories may be
intherange packaging.
4. Dispose of/recycle all packaging materials.
5. Check that the range is level. See the “Level Range” section.
6. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by shipping material.
Dry thoroughly with a soft cloth. For more information, see
the “Range Care” section of the Use & Care Guide.
7. Read the Use & Care Guide.
8. Turn on surface burners and oven. See the Use & Care
Guide for specic instructions on range operation.
NOTE: Odors and smoke are normal when the oven
isusedthe first few times.
If Range Does Not Operate, Check the Following:
Household fuse is intact and tight or circuit breaker
hasnottripped.
Gas pressure regulator shut-o valve is in the open position.
Range is plugged into a grounded 3 prong outlet.
Electrical supply is connected.
9. When the range has been on for 5 minutes, check for heat.
If the range is cold, turn o the range and check that the
gas supply line shut-o valve is open.
If the gas supply line shut-o valve is closed, open it
and then repeat the 5-minute test as outlined above.
If the gas supply line shut-o valve is open, close it,
and contact a qualied technician.
If You Need Assistance or Service:
Please reference the back cover of the Use & Care Guide
tocontact service.
A
A. Hinge notch
14
GAS CONVERSIONS
Gas conversions from Natural gas to propane or from propane
toNatural gas must be done by a qualied installer.
Propane Conversion
1. Turn the manual shut-o valve to the closed position.
2. Unplug range or disconnect power.
To Convert Gas Pressure Regulator (Natural Gas
toPropane)
1. Remove the storage drawer. See the “Remove/Replace
Drawer” section.
2. Locate gas pressure regulator at rear of the drawer
compartment.
IMPORTANT: Do not remove the gas pressure regulator.
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make
sure gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
A
B
C
A. Gas supply line
B. Manual shut-off valve closed position
C. To range
A. Gas pressure regulator
15
3. Remove plastic cover from gas pressure regulator cap.
4. Turn gas pressure regulator cap counterclockwise with a
5/8" (1.6 cm) combination wrench to remove.
NOTE: Do not remove the spring beneath the cap.
5. Turn over the gas pressure regulator cap and reinstall on
regulator so that the hollow end faces out and the marking
ê LP” is facing the direction shown in the above drawing.
6. Replace plastic cover over gas pressure regulator cap.
To Convert Surface Burners (Natural Gas
to Propane)
1. Remove burner cap.
2. Remove the burner base.
3. Apply masking tape to the end of a 9/32" (7 mm) nut
driver to help hold the gas orice spud in the nut driver
while changing it. Press nut driver down onto the gas orice
spud and remove by turning it counterclockwise and lifting
out. Set gas orice spud aside.
4. Remove the orice spuds shipped in the literature package
in the oven. Gas orice spuds are stamped with a number,
marked with 1 or 2 color dots, and have a groove in the hex
area. Replace the Natural gas orice spud with the correct
propane orice spud.
Refer to the following chart for correct propane orifice
spud ratings and to spud holder card for proper placement.
Fully insert choke into bottom of X-Large burner base.
Choke should snap into place.
NOTE: Use only for spreader bases marked “XL.”
Propane Orifice Spud Chart for Surface Burners
Burner
Rating/Type
Color Size
(mm)
ID
number
Placement
15,000 BTU/
Stacked*
Silver
Black/Orange
1.05
0.32
L105
L32
LF
14,200
BTU/Ultra/
Stacked*
Silver 1.05 L105 RF
8,000 BTU/
Semi
Red/Orange 0.85 L85 RR/CTR
5,000 BTU/
Auxi
Red/Blue 0.65 L65 LR
1,200 BTU/
Stacked/
Simmer*
Black/Orange 0.32 L32 LF
(Simmer)
* Not in all kits/models
NOTE: Refer to the model/serial/rating plate located on the
oven frame behind the top left-hand side of the oven door for
proper sizing of spuds for each burner location.
5. Place Natural gas orice spuds in the orice spud bag.
IMPORTANT: Keep the Natural gas orifice spuds in case
ofreinstallation with Natural gas.
6. Replace the burner base.
7. Replace burner cap.
8. Repeat steps 1 through 7 for the remaining burners.
A
B
C
D
Side view before
Side view after
E
NG
LP
NG
LP
A. Plastic cover
B. Gas pressure regulator cap with solid end facing out
C. Gas pressure regulator cap with hollow end facing out
D. Washer
E. Gas pressure regulator cap
D
A
B
C
A. Igniter electrode
B. Burner cap
C. Gas tube opening
D. Burner base
A
B
C
X-Large Burner
A. Burner cap
B. Burner base
C. Choke (for use with x-large burner, propane
only)
A
B
C
D
A. Igniter electrode
B. Orifice spud
C. Orifice spud holder
D. Screws
A
A. Propane groove
16
To Convert Oven Bake Burner (Natural Gas
toPropane)
1. Remove the oven racks and the oven door. See the “Oven
Door” section.
2. Remove 2 screws and washers at the rear of the oven
bottom.
3. Lift the rear of the oven bottom up and back until the front
of the panel is away from the front frame. Remove from
oven and set it aside on a covered surface.
4. Remove 2 screws from the bake burner.
5. Slide the front of the bake burner to the side to remove tab
from front of oven. Lift the back of the bake burner o the
oven orice and set the bake burner aside. Do not
disconnect the wire.
6. Apply masking tape to the end of a 3/8" (1 cm) nut driver
to help hold the gas orice spud in the nut driver while
changing it. Press nut driver down onto the gas orice spud
and remove by turning the Natural gas bake burner orice
spud counterclockwise to remove. The spud will be stamped
with a “47.”
7. Replace the “47” spud with a “56” spud. Install the
propane bake burner orice spud, turning it clockwise
until snug.
IMPORTANT: Do not overtighten.
8. Position the back of the bake burner over the oven orice,
and then align the holes for the screws.
9. Reattach the bake burner with 2 screws.
10. Position the front of the oven bottom panel toward the
frontframe, and then lower the rear of the oven bottom
panel into the oven.
11. Reattach the oven bottom panel with 2 screws and
2washers.
To Convert Oven Broil Burner (Natural Gas
toPropane) (on some models)
1. Remove the 1 screw from the broil burner.
2. Remove the ame spreader.
3. Remove the broil burner from the broil burner orice hood.
NOTE: The broil burner will hang in the back of the oven
while you are changing the orifice hood.
A
B
A. Screws
B. Oven bottom
A
B
A. Bake burner
B. Screws
A
A. Oven orifice
A
A. Orifice spud
C
D
A
B
A. Broil burner
B. Flame spreader
C. Screws
D. Orifice hood
17
4. Apply masking tape to the end of a 3/8" (1 cm) nut driver
to help hold the gas orice spud in the nut driver while
changing it. Press nut driver down onto the gas orice
spud and remove by turning the Natural gas broil burner
orice hood counterclockwise to remove. The hood will be
stamped with a “155.”
5. Replace the “155” hood with a “100” hood. Install the
propane broiler burner orice hood, turning it clockwise
untilsnug.
IMPORTANT: Do not overtighten.
6. Place the broil burner on the broil burner orice hood.
Insertthe broil burner ceramic igniter in the hole in the
rearof the oven.
7. Replace the ame spreader with all 4 tabs facing up
andthe notches toward the rear of the oven.
8. Position the broil burner against the top of the oven
andattach it with 1 screw.
9. Replace storage drawer. See the “Remove/Replace
Drawer”section.
10. Replace the oven door. See the “Oven Door” section.
11. Replace the oven racks.
Complete Installation (Natural Gas to Propane)
1. Refer to the “Make Gas Connection” section for proper
connection of the range to the gas supply.
2. Refer to the “Electronic Ignition System” section for proper
burner ignition and operation.
3. Refer to the “Adjust Flame Height” section for burner
ameadjustments.
IMPORTANT: You may have to adjust the low setting for
each cooktop burner.
Checking for proper cooktop flame is very important. The
small inner cone should have a very distinct blue flame
1/4" to 1/2" (0.64 to 1.3 cm) long. The outer cone is not as
distinct as the inner cone. Propane flames have a slightly
yellow tip.
4. Refer to “Complete Installation” in the “Installation
Instructions” section of this manual to complete this
procedure.
Natural Gas Conversion
1. Turn the manual shut-o valve to the closed position.
2. Unplug range or disconnect power.
To Convert Gas Pressure Regulator (Propane
toNatural Gas)
1. Remove the storage drawer. See the “Remove/Replace
Drawer” section.
2. Locate gas pressure regulator at rear of the drawer
compartment.
IMPORTANT: Do not remove the gas pressure regulator.
x.xx
A
A. Orifice hood
IMPORTANT: Make sure to save the orifices that have
just been replaced in the conversion.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
A
B
C
A. Gas supply line
B. Manual shut-off valve closed position
C. To range
A. Gas pressure regulator
18
3. Remove plastic cover from gas pressure regulator cap.
4. Turn gas pressure regulator cap counterclockwise with a
5/8" (1.6 cm) combination wrench to remove.
NOTE: Do not remove the spring beneath the cap.
5. Turn over the gas pressure regulator cap and reinstall
onregulator so that the solid end faces out and the
marking “
ê NG” is facing the direction shown in the
abovedrawing.
6. Replace plastic cover over gas pressure regulator cap.
To Convert Surface Burners (Propane to
Natural Gas)
1. Remove burner cap.
2. Remove the burner base.
3. Apply masking tape to the end of a 9/32" (7 mm) nut
driver to help hold the gas orice spud in the nut driver
while changing it. Press nut driver down onto the gas orice
spud and remove by turning it counterclockwise and lifting
out. Set gas orice spud aside.
4. Gas orice spuds are stamped with a number on the side.
Replace the propane orice spud with the correct Natural
gas orice spud.
Refer to the following chart for the correct Natural gas
orifice spud placement.
Remove choke from X-Large burner base.
Natural Gas Orifice Spud Chart
Burner Rating Color Size (mm) ID Number
19,000 BTU (ST) White/Gray 1.84 184
18,000 BTU Blue 1.94 194
17,000 BTU (ST) N/A 1.75 175
17,000 BTU White/Blue 1.90 190
15,000 BTU White/Green 1.80 180
9,200 BTU White/Black 1.35 135
8,000 BTU White/Yellow 1.25 125
5,000 BTU White/Orange 1.00 100
1,200 BTU Black 0.52 52
NOTE: Refer to the model/serial/rating plate located on the
oven frame behind the top left-hand side of the oven door for
proper sizing of spuds for each burner location.
5. Place propane orice spuds in the orice spud bag.
IMPORTANT: Keep the propane orifice spuds in case
ofreinstallation with propane.
6. Replace the burner base.
7. Replace burner cap.
8. Repeat steps 1 through 7 for the remaining burners.
To Convert Oven Bake Burner (Propane
toNaturalGas)
1. Remove the oven racks and the oven door. See the “Oven
Door” section.
2. Remove 2 screws and washers at the rear of the oven
bottom.
A
B
C
D
Side view before
Side view after
E
NG
LP
LP
NG
A. Plastic cover
B. Gas pressure regulator cap with hollow end facing out
C. Gas pressure regulator cap with solid end facing out
D. Washer
E. Gas pressure regulator cap
D
A
B
C
A
B
C
A. Igniter electrode
B. Burner cap
C. Gas tube opening
D. Burner base
X-Large Burner
A. Burner cap
B. Burner base
C. Choke (for use with x-large burner, propane
only)
A
B
C
D
A. Igniter electrode
B. Orifice spud
C. Orifice spud holder
D. Screws
XXX
A
A. Stamped number
19
3. Lift the rear of the oven bottom up and back until the front
of the panel is away from the front frame. Remove from
oven and set it aside on a covered surface.
4. Remove 2 screws from the bake burner.
5. Slide the front of the bake burner to the side to remove tab
from front of oven. Lift the back of the bake burner o the
oven orice and set the bake burner aside. Do not
disconnect the wire.
6. Apply masking tape to the end of a 3/8" (1 cm) nut driver
to help hold the gas orice spud in the nut driver while
changing it. Press nut driver down onto the gas orice spud
and remove by turning the propane bake burner orice
spud counterclockwise to remove. The spud will be stamped
with a “56.”
7. Replace the “56” spud with a “47” spud. Install the Natural
gas bake burner orice spud, turning it clockwise until snug.
IMPORTANT: Do not overtighten.
8. Position the back of the bake burner over the oven orice,
and then align the holes for the screws.
9. Reattach the bake burner with 2 screws.
10. Position the front of the oven bottom panel toward the front
frame, and then lower the rear of the oven bottom panel
into the oven.
11. Reattach the oven bottom panel with 2 screws and
2washers.
To Convert Oven Broil Burner (Propane
toNaturalGas) (on some models)
1. Remove 1 screw from the broil burner.
2. Remove the ame spreader.
3. Remove the broil burner from the broil burner orice hood.
NOTE: The broil burner will hang in the back of the oven
while you are changing the orifice hood.
4. Apply masking tape to the end of a 3/8" (1 cm) nut driver
to help hold the gas orice spud in the nut driver while
changing it. Press nut driver down onto the gas orice
spud and remove by turning the propane broil burner
orice hood counterclockwise to remove. The hood will be
stamped with a “100.”
A
B
A. Screws
B. Oven bottom
A
B
A. Bake burner
B. Screws
A
A. Oven orifice
A
A. Orifice spud
C
D
A
B
A. Broil burner
B. Flame spreader
C. Screws
D. Orifice hood
20
5. Replace the “100” hood with a “155” hood. Install the
Natural gas broiler burner orice hood, turning it clockwise
until snug.
IMPORTANT: Do not overtighten.
6. Place the broil burner on the broil burner orice hood.
Insertthe broil burner ceramic igniter in the hole in the
rearof the oven.
7. Replace the ame spreader with all 4 tabs facing up
andthe notches toward the rear of the oven.
8. Position the broil burner against the top of the oven
andattach it with 1 screw.
9. Replace the storage drawer. See the “Remove/Replace
Drawer” section.
10. Replace the oven door. See the “Oven Door” section.
11. Replace the oven racks.
Complete Installation (Propane to Natural Gas)
1. Refer to the “Make Gas Connection” section for proper
connection of the range to the gas supply.
2. Refer to the “Electronic Ignition System” section for proper
burner ignition and operation.
3. Refer to the “Adjust Flame Height” section for burner ame
adjustments.
IMPORTANT: You may have to adjust the low setting
foreach cooktop burner.
Checking for proper cooktop, bake, and broil burner
flameis very important. Natural gas flames do not
haveyellow tips.
4. Refer to “Complete Installation” in the “Installation
Instructions” section of this manual to complete
thisprocedure.
Adjust Flame Height
Adjust Surface Burner Flame
Adjust the height of top burner ames. The cooktop “low”
burner ame should be a steady blue ame approximately
1/4" (0.64 cm) high. propane ames have a slightly yellow tip.
To Adjust Standard Burner:
The ame can be adjusted using the adjustment screw in the
center of the valve stem. The valve stem is located directly
underneath the control knob.
If the “Low” Flame Needs to Be Adjusted:
1. Light 1 burner and turn to lowest setting.
2. Remove the control knob.
Hold the knob stem with a pair of pliers. Use a small
flat-blade screwdriver to turn the screw located in the
center of the control knob stem until the flame is the proper
size. Turning the screw clockwise will increase the flame size
and counterclockwise will decrease the flame size.
3. Replace the control knob.
4. Test the ame by turning the control from the low position
to the high position, checking the ame at each setting.
5. Repeat the previous steps for each burner.
To Adjust Double Burner (on some models):
1. Light burner and turn to lowest setting where both inner
andouter burners are lit.
2. Remove the control knob.
3. Insert a 1/8" (3 mm) at-blade screwdriver into the
adjustment locations shown in the following illustration
andengage the slotted screw. Turn the screw until the
ameis the proper size. Turning the screw clockwise
willincrease the ame size and counterclockwise will
decrease the ame size.
x.xx
A
A. Orifice hood
IMPORTANT: Make sure to save the orifices that have
just been replaced in the conversion.
A. Low flame
B. High flame
A
B
A
B
C
A. Control knob stem
B. Screwdriver
C. Pliers
A
B
C
A. Control knob stem
B. Screwdriver
C. Pliers
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Kenmore Elite 75223 Guide d'installation

Catégorie
Cuisinières
Taper
Guide d'installation