Samsung WF448AAP Manuel utilisateur

Catégorie
Machines à laver
Taper
Manuel utilisateur

Ce manuel convient également à

Washing Machine
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
WF448AAW
WF448AAP
WF448AAE
WF428AAW
WF428AAL
WF448AAW-02535B-11_EN.indd 1WF448AAW-02535B-11_EN.indd 1 2011-01-13 ¿ÀÀü 10:26:582011-01-13 ¿ÀÀü 10:26:58
2_ Features of your new VRT™ STEAM washer
features of your new VRT™
STEAM washer
1. VRT™ (Vibration Reduction Technology)
This Samsung washer performs smoothly at top spin speeds, minimizing noise and vibration.
2. The Largest Capacity
Samsung’s extra-large capacity laundry machine can wash a full set of your bedding, a king-
size comforter, or up to 28 bath towels in a single load. Since you don’t have to do as many
loads, you save time, money, water and energy.
3. Deep steam (WF448***)
The Deep Steam feature boosts cleaning performance and loosens grime and dirt, thus
providing superior cleaning results.
4. Diamond drum™
Take gentle care of your fabrics. With inside holes 36% smaller than those of conventional
drums,the diamond drum prevents fabrics from sticking out and consequently being
damaged.
5. Stylish design
The stylish design of this washer blends well with your environment.
6. LCD Display & Center jog dial
The Jog dial enables you to select cycles in both directions with ease, and the LCD display is
easy to use and understand.
7. DD Motor
The power to handle anything! Our direct-drive inverter motor delivers power right to the
washer tub from a variable speed, reversible motor. A beltless direct-drive motor generates
a higher spin speed of 1,300rpms for more effective, quiet operation. The washer also has
fewer moving parts, meaning fewer repairs.
8. Sanitize
When selecting this cycle, the water heats to an extra high temperature to remove 99.9% of
certain bacteria typically found on clothing, bedding, or towels. This certification is conducted
by NSF International, an independent third-party testing and certification organization.
Please check garment care label to avoid garment damage. Only sanitizing cycles have been
designed to meet the requirements of this protocol for sanitization efficacy.
NSF Protocol P172
Sanitization Performance of Residential and
Commercial, Family-Sized Clothes Washers
WF448AAW-02535B-11_EN.indd Sec9:2WF448AAW-02535B-11_EN.indd Sec9:2 2011-01-13 ¿ÀÀü 10:27:062011-01-13 ¿ÀÀü 10:27:06
Features of your new VRT™ STEAM washer _3
9. Pedestal with Storage Drawers (Model No : WE357*)
An optional 15” pedestal is available to raise the washer for easier loading and unloading.
It also offers a built-in storage drawer that can hold a 100 oz. bottle of detergent
10. Stacking (Model No : SK-5A/XAA)
Samsung washers and dryers can be stacked to maximize usable space. An optional
stacking kit is available for purchase from your Samsung retailer.
<Pedestal with Storage Drawers> <Stacking>
WF448AAW-02535B-11_EN.indd Sec9:3WF448AAW-02535B-11_EN.indd Sec9:3 2011-01-13 ¿ÀÀü 10:27:062011-01-13 ¿ÀÀü 10:27:06
4_ Safety information
safety information
Congratulations on your new Samsung SilverCare™ Washer. This manual
contains important information on the installation, use and care of your
appliance. Please take time to read this manual to take full advantage of your
Washer’s many benefits and features.
WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS
Warnings and Important Safety Instructions in this manual do not cover all possible conditions and
situations that may occur. It is your responsibility to use common sense, caution, and care when installing,
maintaining, and operating your Washer.
IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS
WARNING
Hazards or unsafe practices that may result in severe personal injury or
death.
CAUTION
Hazards or unsafe practices that may result in minor personal injury or
property damage.
CAUTION
To reduce the risk of fire, explosion, electric shock, or personal injury when
using your washer, follow these basic safety precautions:
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions explicity.
Unplug the power plug from the wall socket.
Make sure the machine is grounded to prevent electric shock.
Call the service center for help.
Notice
Read all instructions before using the appliance.
With any equipment using electricity and moving parts, potential hazards exist.
To safely operate this appliance, become familiar with its operation and be careful when
using it.
Install and store your washer inside, away from exposure to weather.
Install and level your washer on a floor that can support its weight.
Your washer must be properly grounded. Never plug it into an ungrounded outlet. See page
8 for more information on grounding your washer.
WF448AAW-02535B-11_EN.indd Sec1:4WF448AAW-02535B-11_EN.indd Sec1:4 2011-01-13 ¿ÀÀü 10:27:072011-01-13 ¿ÀÀü 10:27:07
Safety information _5
To reduce the risk of fire or explosion:
Do not wash items that have been washed, soaked, or treated with gasoline, dry
cleaning solvents, or other flammable or explosive substances. They give off vapors that
could ignite or explode. Rinse by hand any material that has been exposed to cleaning
solvent or other flammable liquids or solids before putting in your washer. Be sure that
all traces of such liquids, solids, and fumes have been removed. Dangerous substances
include acetone, denatured alcohol, gasoline, kerosene, certain liquid household
cleaners and spot removers, turpentine, waxes, and wax removers.
Do not put gasoline, dry cleaning solvents, or other flammable or explosive substances
into the washer.
Under certain conditions, hydrogen gas may be produced in a hot water system–such
as your hot water heater-- that has not been used for two weeks or more. HYDROGEN
GAS IS EXPLOSIVE. If your hot water system has not been used for two weeks or
more, turn on all hot water faucets in your home, and let the water flow for several
minutes before using your washer. This will release any hydrogen gas build–up. Since
hydrogen gas is flammable, do not smoke or light an open flame during this time.
Unplug the power cord before servicing your washer.
Do not reach into the appliance when the tumbler is moving.
Do not let children play on or in your washer. The washer door isn’t easily opened from the
inside, and a child could be seriously injured if trapped inside.
Do not tamper with the controls.
Do not repair, replace, or service any part of your washer yourself unless you fully
understand the recommended user–repair instructions and have the skills to carry them
out. Work done by an unauthorized person may void your warranty.
Store laundry detergents and other laundry supplies in a cool, dry place out of children’s reach.
Do not wash or dry items that are soiled with vegetable or cooking oil. These items may contain
some oil after laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself.
Do not use chlorine bleach, ammonia, or acids (such as vinegar or rust remover) in the
same wash. Hazardous fumes can form.
Do not wash fiberglass materials. Small particles can stick to fabrics washed in subsequent
loads and cause skin irritation.
Before disposing of your washer, remove the door so that children or small animals cannot
get trapped inside.
Do not sit on top of your Washer.
Inlet hoses are subject to damage and deterioration over time. Check the hoses periodically
for bulges, kinks, cuts, wear or leaks, and replace them every five years.
Ensure pockets are free from small irregularly shaped hard objects, foreign materials such
as coins, knives, pins, etc. These objects could damage your washer.
Do not wash clothing with large buckles, buttons, or other heavy metal.
Do not wash throw rug or doormat.
If you wash throw rug or doormat, the sand will accumulate inside the washer. It may
result in error such as not draining.
Make sure the detergent drawer is closed before you put laundry into the washer or remove
laundry from the washer.
If the detergent drawer is open, you could strike the drawer with your head and injure yourself.
WARNING
WARNING
WARNING
WARNING
WF448AAW-02535B-11_EN.indd Sec1:5WF448AAW-02535B-11_EN.indd Sec1:5 2011-01-13 ¿ÀÀü 10:27:072011-01-13 ¿ÀÀü 10:27:07
6_ Contents
contents
INSTALLING YOUR WASHER
7
7 Unpacking your washer
7 Overview of your washer
8 Electrical
8 Grounding
8 Water
9 Drain facility
9 Flooring
9 Location considerations
9 Alcove or closet installation
9 Undercounter installation(washer only)
10 With optional pedestal base or stacking kit
11 Important note to installer
OPERATING INSTRUCTIONS
13
13 Loading your washer
13 Getting started
WASHING A LOAD OF LAUNDRY
14
14 Overview of the control panel
16 Child lock
16 Interior Lamp
16 Select the Language
16 Garment+
17 My cycle
17 Washing clothes using the cycle selector
18 For SilverCare™ washing
18 Using steam wash (WF448***)
19 Detergent use
19 Features
MAINTAINING YOUR WASHER
21
21 Cleaning the exterior
21 Cleaning the interior
21 Cleaning the dispensers
21 Storing your washer
22 Cleaning the debris filter
22 Cleaning the door seal/bellow
22 Preserving the top cover and the front frame
TROUBLESHOOTING
23
23 Check these points if your washer…
25 Information codes
APPENDIX
27
27 Fabric care chart
28 Cycle chart
30 Helping the environment
30 Declaration of conformity
30 Specification
WF448AAW-02535B-11_EN.indd Sec3:6WF448AAW-02535B-11_EN.indd Sec3:6 2011-01-13 ¿ÀÀü 10:27:072011-01-13 ¿ÀÀü 10:27:07
Installing your washer _7
installing your washer
UNPACKING YOUR WASHER
Unpack your Washer and inspect it for shipping damage. Make sure you have received all of the items
shown below. If your Washer was damaged during shipping, or you do not have all of the items, contact
1-800-SAMSUNG(726-7864).
To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.
Packing materials can be dangerous to children; keep all packing material (plastic bags, polystyrene,
etc.) well out of the reach of children.
OVERVIEW OF YOUR WASHER
Wrench Bolt Hole Covers Water Supply Hoses Hose Guide
Plastic Zip Hose Tie
01 Installing your washer
Adjustable legs
Cold water supply
hose
Hot water supply
hose
Drain Hose
Detergent drawer
Control panel
Door
Tub
Debris filter
Drain tube
Filter cover
WARNING
WF448AAW-02535B-11_EN.indd Sec2:7WF448AAW-02535B-11_EN.indd Sec2:7 2011-01-13 ¿ÀÀü 10:27:072011-01-13 ¿ÀÀü 10:27:07
8_ Installing your washer
BASIC LOCATION REQUIREMENTS
Electrical
120 Volt 60 Hz 15 AMP fuse or circuit breaker
Individual branch circuit serving only your Washer is recommended.
Your Washer is equipped with a power cord.
NEVER USE AN EXTENSION CORD.
Grounding
ELECTRICAL GROUNDING IS REQUIRED ON THIS APPLIANCE.
This appliance must be grounded. In the event of malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a path of least resistance for electric current.
This appliance is equipped with a power cord having a three-prong grounding plug for use in a
properly installed and grounded outlet.
Improper connection of the equipment-grounding conductor can result in a risk of electrical
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the
appliance is properly grounded. Do not modify the plug provided with the appliance – if it
does not fit the outlet, have a proper outlet installed by a qualified electrician.
IMPORTANT SAFETY PRECAUTIONS
To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and
grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No.
70 Latest Revision and local codes and ordinances. It is the personal responsibility of the
appliance owner to provide adequate electrical service for this appliance.
NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT
WATER PIPES.
Water
To correctly fill your Washer in the proper amount of time, water pressure of 20-116psi (137-
800kPa) is required.
Water pressure less than 20 psi may cause water valve failure, or may not allow the water valve
to shut off completely. Or, it may extend the fill time beyond what your Washer controls allow,
resulting in your Washer turning off. A time limit is built into the controls in the event of an internal
hose becoming loose and flooding your home.
The water faucets must be within 4 feet/122cm of the back of your Washer for the inlet hoses
provided with your Washer.
Accessory inlet hoses are available in various lengths up to 10 feet/305cm for faucets that
are further away from the back of your Washer.
To avoid the possibility of water damage:
Have water faucets easily accessible
Turn off faucets when the washer is not in use.
Periodically check that there is no leakage from the water inlet hose fittings.
CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS.
installing your washer
CAUTION
WARNING
WARNING
CAUTION
WF448AAW-02535B-11_EN.indd Sec2:8WF448AAW-02535B-11_EN.indd Sec2:8 2011-01-13 ¿ÀÀü 10:27:082011-01-13 ¿ÀÀü 10:27:08
Installing your washer _9
Drain facility
The recommended height of the standpipe is 18 in/46 cm. The drain hose must be routed
through the drain hose clip to the standpipe. The standpipe must be large enough to accept the
outside diameter of the drain hose. The drain hose is attached at the factory.
Flooring
For best performance, your Washer must be installed on a solidly constructed floor. Wood floors
may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting
and soft tile surfaces are contributing factors in vibration may cause your washer to move slightly
during the spin cycle.
Never install your washer on a platform or weakly supported structure.
Location considerations
Do not install your washer in areas where water may freeze, since your washer will always
maintain some water in its water valve, pump, and hose areas. This can cause damage the belts,
the pump, hoses and other components.
Alcove or closet installation
MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:
Sides – 1 in / 25 mm
Rear – 4 in / 102 mm
Top – 17 in / 432 mm
Closet Front – 2 in / 51 mm
If the washer and dryer are installed together, the closet front must have at least a 72 in² (465
cm²) unobstructed air opening. Your washer alone does not require a specific air opening.
A. Recessed area
B. Side view - closet or confined area
Undercounter installation(washer only)
01 Installing your washer
1 in.
(2.5 cm)
27 in.
(68.6 cm)
1 in.
(2.5 cm)
40 in.
(101.6 cm)
B
2 in.
(5 cm)
31.9 in.
(81.1 cm)
4 in.
(10.2 cm)
17 in.
(43.2 cm)
A
1 in.
(2.5 cm)
27 in.
(68.6 cm)
1 in.
(2.5 cm)
1 in.
(2.5 cm)
27 in.
(68.6 cm)
WF448AAW-02535B-11_EN.indd Sec2:9WF448AAW-02535B-11_EN.indd Sec2:9 2011-01-13 ¿ÀÀü 10:27:082011-01-13 ¿ÀÀü 10:27:08
10_ Installing your washer
installing your washer
With optional pedestal base or stacking kit
Required Dimensions for Installation With Pedestal
Required Dimensions for Installation With Stacking Kit
341.1 in.
(86.5 cm)
4 in.
(10 cm)
51.7 in. (131.4 cm) to clear open door
27 in.
(68.6 cm)
39 in.
(99.1 cm)
53.6 in.
(136.2 cm)
31.9 in.
(81.1 cm)
3 in.
(7.6 cm)
Closet or Door
48 in.² *
(310 cm²)
3 in.
(7.6 cm)
24 in.² *
(155 cm²)
1 in.
(2.5 cm)
5.5 in.**
(14 cm)
2.5 in.
(6.3 cm)
6 in. *
(15.2 cm)
1 in.
(2.5 cm)
78 in.
(198.1 cm)
27 in.
(68.6 cm)
* Required spacing
** External exhaust elbow requires
additional space.
WF448AAW-02535B-11_EN.indd Sec2:10WF448AAW-02535B-11_EN.indd Sec2:10 2011-01-13 ¿ÀÀü 10:27:092011-01-13 ¿ÀÀü 10:27:09
Installing your washer _11
IMPORTANT NOTE TO INSTALLER
Please read the following instructions carefully before installing your Washer.
These instructions should be retained for future reference.
We recommend you hire a professional for installation of this washer.
STEP 1
Removing the Shipping Bolts
Before using your Washer, you must remove the four shipping
bolts from the back of the unit.
1. Loosen all the bolts with the supplied wrench.
2. Slide the bolt and spacer up and remove the bolt with the
spacer through the hole in the rear wall of your washer.
Repeat for each bolt.
3. Fill the holes with the supplied Bolt Hole Covers (See page 7).
4. Keep the shipping bolts and spacers for future use.
STEP 2
Selecting a Location
Before you install your washer, make sure the location:
Has a hard, level surface
Is away from direct sunlight
Has adequate ventilation
Will not freeze (below 32°F or 0°C)
Is away from heat sources such as oil or gas
Has enough slack for the power cord.
Doesn’t have any carpeting that will obstruct ventilation openings.
STEP 3
Installing your Washer
1. Place the drain hose in the drain facility. Be
sure an airtight connection is NOT made
between the drain hose and the standpipe.
The standpipe must be at least 18 in or 46
cm high.
Caution must always be exercised to
avoid collapsing or damaging the drain
hose. For best results, the drain hose
should not be restricted in any way – by
elbows, couplings, or excessive lengths.
For situations where the drain hose
cannot be conveniently elevated to at
least 18 in or 46 cm, the drain hose must
be supported.
01 Installing your washer
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie strap
Laundry tub Stand pipe
WF448AAW-02535B-11_EN.indd Sec2:11WF448AAW-02535B-11_EN.indd Sec2:11 2011-01-13 ¿ÀÀü 10:27:102011-01-13 ¿ÀÀü 10:27:10
12_ Operating instructions
installing your washer
2. Check the inlet hose to ensure a washer is inside each fill
hose.
Thread the inlet hoses to the HOT and COLD faucet
connections.
On the other end of the hose, check for one rubber washer
per hose and install each fill hose to the water valve. Make
sure the hose with the Hot printed line is attached to the
HOT faucet. Tighten by hand until snug, then two-thirds of a
turn with pliers.
For correct water use, connect both HOT and COLD water
valves. If either or both are not connected, an “nF” (no fill)
error can occur.
3. Turn on the “HOT” and “COLD “water supply and check all
connections at the water valve and the faucet for leaks.
4. Plug the power cord into a 3-Prong, well grounded 120 volt
60 Hz approved electrical outlet protected by a 15-amp
fuse or comparable circuit breaker.
Your washer is grounded through the third prong of the
power cord when plugged into a three-prong grounded
receptacle.
5. Slide your washer into position.
6. Level your washer by turning the leveling legs in or out as
necessary by hand or by using the wrench included with
your washer.
When your washer is level, tighten the Locking nuts using
the wrench or (-) flathead screwdriver.
Your Washer must be leveled on all four sides. A
carpenter’s level should be used on all four corners of
your Washer. It’s a good idea after the first dozen washes
to recheck your washer’s levelness.
Avoid damage to the legs. Do not move
the Washer unless the Locking-nuts are
fastened to the bottom of the Washer.
Levelling Leg
Locking Nut
Cold Hot
Cold printed Hot printed
Rubber Washer
WF448AAW-02535B-11_EN.indd Sec5:12WF448AAW-02535B-11_EN.indd Sec5:12 2011-01-13 ¿ÀÀü 10:27:102011-01-13 ¿ÀÀü 10:27:10
Operating instructions _13
operating instructions
LOADING YOUR WASHER
You can fill the tub with dry, unfolded clothes; but DO NOT OVERLOAD the tub.
Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or
wrinkling of the load.
Wash delicate items such as bras, hosiery, and other lingerie in the Delicates cycle with similar
lightweight items.
When washing big bulky items or a few smaller items that don’t fill the tub completely – a rug, a pillow,
stuffed toys, or one or two sweaters, for example – add a few towels to improve tumbling and spin
performance.
During the spin cycle, the washer may add additional water to redistribute the excessive imbalance
inside the drum.
When washing heavily soiled loads, do not overload your Washer in order to assure good cleaning
results.
To add a forgotten item:
1. Press the Start/Pause Button.
2. Wait for the Door Lock light to go out (5 seconds)
3. Add the item, close the door, and press the Start/Pause Button.
After a 10-second pause, the cycle will resume.
To ensure thorough cleaning, add items within five minutes of starting the wash cycle.
Try washing bedding, towels, undergarments, and other articles that usually have close body
contact using the SilverCare™ Option, which sanitizes using cold water.
GETTING STARTED
1. Load your Washer.
2. Close the door.
Push the laundry into the drum completely to prevent the laundry from being caught in the door or
from falling out of the drum.
3. Add detergent and additives to the dispenser (see pages 20~21).
4. Select the appropriate cycle and options for the load (see pages 14~16).
5. Press the Start/Pause Button.
6. The Wash Indicator light will illuminate.
7. The estimated cycle time will appear in the display.
The time may fluctuate to better indicate the time remaining in the cycle.
The actual time required for a cycle may differ from the estimated time in the display depending on the
water pressure, water temperature, detergent, and laundry.
8. Before your washer starts to fill, it will make a series of clicking noises to check the door lock and do a
quick drain.
When the cycle is complete, the Door Lock light will go out and “End” will appear in the display.
DO NOT attempt to open the door until the Door Lock light is off. To add a forgotten item, see
“Loading your Washer” section. (page 13)
When your Washer is restarted after a pause, expect a delay of up to 15 seconds before the cycle
continues.
Pressing Power button cancels the cycle and stops your washer.
The Pre Wash, Wash, Rinse and Spin indicator lights will illuminate during those portions of the cycle.
02 Operating instructions
CAUTION
WF448AAW-02535B-11_EN.indd Sec5:13WF448AAW-02535B-11_EN.indd Sec5:13 2011-01-13 ¿ÀÀü 10:27:122011-01-13 ¿ÀÀü 10:27:12
14_ Washing a load of laundry
washing a load of laundry
OVERVIEW OF THE CONTROL PANEL
Cycle Selector
Select the appropriate cycle for the type of load.
This will determine the tumble pattern and spin speed for the cycle.
To minimize wrinkling of laundry, select the Perm Press cycle.
Normal - For most fabrics including cottons, linens, and normally soiled garments.
Heavy Duty - For sturdy, colorfast fabrics and heavily soiled garments.
Whites - For white fabrics with or without bleach.
Perm Press - For wash-and-wear, synthetic fabrics, and lightly to normally
soiled garments.
Sanitize - For heavily soiled, colorfast garments. This cycle heats the water to
150°F to eliminate bacteria.
If Pause is selected during the heating portion of the Sanitize Cycle, your
Washer door will remain locked for your safety.
Towels - For bath towels, washcloths and mats.
Bedding - For bulky items such as blankets and sheets. When you are
washing comforters, use liquid detergent.
Deep steam (WF448***) -
For heavily soiled, colorfast garments, this cycle
provides high washing temperature and steam and is efficient in cleaning stains.
Delicates - For sheer fabrics, bras, lingerie silk, and other handwash-only
fabrics. For best results, use liquid detergent.
Hand Wash - For handwashable, special care garments.
Wool - For machine-washable wool. Loads should be under 8 pounds.
The wool wash cycle of this machine has been approved by
Woolmark for the washing of machine washable Woolmark
products provided that the products are washed according
to the instructions on the garment label and those issued by
the manufacturer of this washing machine, M0509
Quick Wash - For lightly soiled garments needed quickly.
Rinse + Spin - Use for loads that need rinsing only or to add rinse-added
fabric softener to a load.
Spin Only - Provides a spin to remove more water..
321 76
5
4
9
10
11
8
12
1
WF448AAW-02535B-11_EN.indd Sec11:14WF448AAW-02535B-11_EN.indd Sec11:14 2011-01-13 ¿ÀÀü 10:27:122011-01-13 ¿ÀÀü 10:27:12
Washing a load of laundry _15
LCD display
The large LCD Display is easy to use. It provides instructions and diagnostics
while keeping you updated on the cycle status and time remaining.
Select Cycle
Option
Press these buttons to select different cycle options.
Extra Wash - Add additional time to the wash cycle for better stain removal.
Extra Rinse - Add an additional rinse at the end of the cycle to more
thoroughly remove laundry additives and perfumes.
Extended Spin - Add additional time to remove more water from loads.
My Cycle - Choose your favorite cycle including temperature, spin, soil level, option, etc.
Pre Wash - To use this feature add detergent to the Pre Wash section of the
detergent compartment. When turned on, the washer fills with cold water and
detergent, tumbles, then drains and advances to the selected wash cycle.
Some cycles cannot be selected with this option.*
* You cannot select the PreWash option in the Delicate, Wool and Quick
Wash cycles.
Delay Start - Any cycle can be delayed for up to 24 hours in one-hour
i
ncrements. Displayed hour indicates the time at which the wash will be started.
SilverCare™
button
Press this button to sanitize your laundry in cold water.
Active silver ions are produced from pure silver plates by the process of
electrolysis and released into the wash water effectively sanitizing your wash,
even in cold water, without bleach. The SilverCare™ system sanitizes while
using 92% less energy use than traditional heat sanitization.
Temperature
selection button
Press the button repeatedly to cycle through the different water temperature options.
Extra Hot/Cold - Heavily soiled, colorfast items. Only available with the Sanitize cycle.
Hot/Cold - Whites and heavily soiled, colorfast items.
Warm/Warm -
Colorfast items. When warm rinse is selected, only the final rinse will be warm.
The other rinses will be cold to conserve energy.
Warm/Cold - Moderately soiled, colorfast items; most wrinkle-free items.
Cold/Cold - Brightly colored, very lightly soiled items.
Spin selection
button
Press the button repeatedly to cycle through the different spin speed options.
Extra High - Removes more water from loads during spin.
To minimize wrinkling of wrinkle-free and no-iron fabrics, DO NOT use
the Extra High spin option for these loads, nor overload your Washer.
High - Use for underwear, t-shirts, jeans and sturdy cottons.
Medium - Use for jeans, wrinkle-free or wash-and-wear items and synthetics.
Low - Use for delicate items needing a slow spin speed.
No Spin - Drains your Washer without spinning. Use for extremely delicate
items that cannot tolerate any spin.
Soil Level
selection button
Press the button to select the Soil Level/washing time.
Heavy - For heavily soiled loads.
Normal - For moderately soiled loads. This setting is best for most loads.
Light - For lightly soiled loads.
Signal selection
button
Press the button to increase or decrease the end of cycle signal volume or
turn off the signal.
Steam selection
button
(WF448***)
Press this button to use steam. Steam Care is available with Heavy Duty,
Normal, Whites, Perm Press, Sanitize, Towels, Bedding cycles. For heavily
soiled, colorfast garments. Steam care improves stain treatment and use less
water of each cycle.
Start/Pause
selection button
Press to pause and restart programs.
Power button
Press once to turn your washer on, press again to turn your washer off. If
the washer is left on for more than 10 minutes without any buttons being
touched, the power automatically turns off.
Drum Light
button
(WF428***)
Press the button to turn the interior Lamp on or off.
2
03 Washing a load of laundry
4
5
7
8
9
10
3
6
11
12
WF448AAW-02535B-11_EN.indd Sec11:15WF448AAW-02535B-11_EN.indd Sec11:15 2011-01-13 ¿ÀÀü 10:27:132011-01-13 ¿ÀÀü 10:27:13
16_ Washing a load of laundry
Child lock
A function that prevents children from playing with your washer.
Once the Child Lock function is activated, the control panel cannot be activated, preventing
children from playing with the washer.
ACTIVATING/DEACTIVATING
If you want to activate/deactivate the Child Lock function, press the Soil Level and Signal
buttons at the same time for 3 seconds.
How It works:
1. To activate or deactivate the Child Lock function, press and hold both the Soil level and
Signal buttons for 3 seconds. Activation/Deactivating the Child Lock function is only available
when the power is on.
2. When the Child Lock function is activated, and any button except for the Power button is
pressed, the buzzer will sound for a short period and the “Child Lock” indicator will turn off
for 10 seconds.
3. The Child Lock function stays on even after the power has been turned on and off or the
power cord has been disconnected and reconnected.
When buttons, other than the Power button, do not respond, please check if the Child
Lock function is on.ower button, do not respond, please check if the “Child Lock”
function is on.
Interior Lamp
1. If the door is opened when the power is on, the Interior Lamp is automatically turned on.
2. If the door is closed when the power is on, the Interior Lamp is automatically turned off.
3. Press the Temp and the Spin buttons simultaneously to turn the Interior Lamp on or off.
4. If 4 minutes have passed after the Interior Lamp is turned on, the Interior Lamp is
automatically turned off.
Select the Language
1. Press the Extra Wash and Extra Rinse buttons simultaneously
for 3 seconds.
2. The “Select the Language” message appears on the display.
3. Turn the Jog Dial to select a language.
You can select English, Spanish, or French.
4. Press the Signal button to select the chosen language.
Garment+
You can add or take out laundry items even after the wash has started, as long as the
“Garment+” light is on. Pushing the Start/Pause button unlocks the door, unless the water is
too hot or if there is too much water in your Washer. If you are able to unlock the door and wish
to continue the wash cycle, close the door and press the Start/Pause button.
washing a load of laundry
WF448AAW-02535B-11_EN.indd Sec11:16WF448AAW-02535B-11_EN.indd Sec11:16 2011-01-13 ¿ÀÀü 10:27:132011-01-13 ¿ÀÀü 10:27:13
Washing a load of laundry _17
My cycle
Allows you to activate your custom wash (temperature, spin, soil level, etc.) with one–button
convenience.
By pushing the My Cycle button, you activate the settings used during the My Cycle mode.
The “My Cycle” light will indicate activation.
You can select all options as follows in “My Cycle” mode.
1. Select cycle using the Cycle Selector dial.
2. After cycle selection, set each option.
See page 28 for available option settings with each cycle.
3. Then, you can start “My Cycle” by pushing the Start/Pause button in “My Cycle” mode.
The cycle and options you select will be displayed the next time you choose “My Cycle”.
You can change the “My Cycle” settings by repeating the same process above.
The last used setting will be displayed the next time you choose “My Cycle”.
Washing clothes using the cycle selector
Your new washing machine makes washing clothes easy, using Samsung’s “Fuzzy Control”
automatic control system. When you select a wash program, the machine will set the correct
temperature, washing time, and washing speed.
1. Turn on your sink’s water tap.
2. Press the Power button.
3. Open the door.
4. Load the articles of clothing one at a time loosely into the drum, without overfilling it.
5. Close the door.
6. Add detergent, softener, and pre-wash detergent (if necessary) into the appropriate
compartments.
Pre-wash is only available when selecting the Cottons, Synthetics, Denim, Sports Wear,
Baby Care, Dark Garment and Daily Wash cycles. It is only necessary if your clothing is
heavily soiled.
7. Use the Cycle Selector to select the appropriate cycle according to the type of material:
Normal, Whites, PermPress,Sanitize, Towels, Bedding, Delicates, Hand Wash, Wool, Quick
Wash, Rinse + Spin, Spin Only, SteamCare, Heavy Duty. The relevant indicators will illuminate
on the control panel.
8. At this time, you can control the wash temperature, the number of rinse cycles, the spinning
speed, and the delay time by pressing the appropriate option button.
9. Press the Start/Pause button on the Cycle Selector and the wash will begin. The process
indicator will light up and the remaining time for the cycle will appear in the display.
Pause Option
1. Within 5 minutes of starting a wash, it is possible to add/remove laundry items to the wash.
2. Press the Start/Pause button to unlock the door.
3. The door cannot be opened when the water is too HOT or the water level is too HIGH.
4. After closing the door, press the Start/Pause button to restart the wash.
When the cycle is finished:
After the total cycle has finished, the power will turn off automatically.
1. Open the door.
2. Remove laundry.
03 Washing a load of laundry
WF448AAW-02535B-11_EN.indd Sec11:17WF448AAW-02535B-11_EN.indd Sec11:17 2011-01-13 ¿ÀÀü 10:27:132011-01-13 ¿ÀÀü 10:27:13
18_ Washing a load of laundry
FOR SILVERCARE™ WASHING
An increased consumer demand for energy-saving products prompted Samsung to develop a system to
use silver, widely known for its antimicrobial properties, as a sanitizing agent in your washing machine.
Pure silver atoms have an electron stripped away by electrolysis during the wash and rinse cycles, which
releases up to 16 million trillion silver ions that then penetrate deep into the fabric to sanitize clothing
(according to U.S. EPA Test Guideline DIS/TSS-13). It does not need hot water or bleach.
Here’s how it works: A grapefruit-sized device alongside the tub uses two pure silver plates the size of large
chewing gum sticks as electrodes in the water inlet system. The resulting positively charged silver atoms
- Silver ions (Ag+) -- are sprayed into the tub during the wash and final rinse cycle.
During tests, this process removed more than 99.9% of bacteria.
Extra delicate blouses, shirts, or even lingerie that can’t be washed in hot water can now be sanitized
effectively without the adverse effects of hot water. The silver plates can easily be replaced by a Service
Technician if needed.
To use :
1. Load the washer.
2. Press the Power button.
3. Select a Cycle by turning the Cycle Selection dial.
4. Press the SilverCare™ button.
5. Add detergent in the dispenser tray for main washing, and add fabric softener up to the marked line.
6. Press the Start/Pause button.
: The washer automatically selects optimal washing conditions by sensing the laundry’s weight.
FOR HOME USE ONLY– COMMERCIAL USERS SHOULD NOTIFY THEIR LOCAL WASTE
TREATMENT AUTHORITIES BEFORE USE
The total number of silver cycles run by the washer is displayed when pushing the Signal button and the
SilverCare™ button simultaneously while the power is on.
LU1 : less than 1000 cycles
LU0 : 1000 cycles
You should replace the SilverCare™ kit when the display reads “LU0” as the electrodes are near the end of
their useful life. Contact 1-800-SAMSUNG.
You cannot choose the SilverCare™ option with the Wool cycle.
USING STEAM WASH (WF448***)
The Steam Wash function injects steam directly into the laundry in the wash tub to increase the wash
temperature and enhance the Soak effect, thus improving the wash performance.
1. Load the washer.
2. Press the Power button.
3. Turn the Cycle Selector and select a Steam Cycle. (The Deep Steam course automatically selects
Steam.)
4. Press the Steam button.
5. Add detergent into the dispenser tray for a wash, and add fabric softener up to the marked line.
6. Press the Start/Pause button.
: The washer automatically selects the optimal wash conditions by sensing the weight of the laundry.
Steam may not necessarily be visible during the steam cycles.
Steam may not be present during entire steam wash cycle.
washing a load of laundry
WF448AAW-02535B-11_EN.indd Sec11:18WF448AAW-02535B-11_EN.indd Sec11:18 2011-01-13 ¿ÀÀü 10:27:142011-01-13 ¿ÀÀü 10:27:14
Washing a load of laundry _19
DETERGENT USE
Your Washer is designed to use high efficiency (HE) detergents.
For best cleaning results, use a high efficiency detergents such as Tide
HE, Wisk HE, Cheer HE or Gain HE*. High efficiency detergents contain
suds suppressors that reduce or eliminate suds. When fewer suds are
produced, the load tumbles more efficiently and cleaning is maximized.
Regular detergent is Not recommended. Please use HE detergents
only.
Reducing the amount of detergent may reduce the quality of cleaning. It is important to pre–treat
stains, sort carefully by color and soil level, and avoid overloading.
* Brand names are trademarks of their respective manufacturers.
FEATURES
Automatic dispenser
Your Washer has separate compartments for dispensing
detergent and color-safe bleach, chlorine bleach, and fabric
softener. All laundry additives are added to their respective
compartments before starting your Washer.
The automatic dispenser MUST ALWAYS be in place before
starting your Washer.
DO NOT open the automatic dispenser when your washer is
running.
To use:
1. Never exceed the manufacturer’s recommendations when
adding detergent.
2. This compartment holds liquid detergent for the main wash
cycle, which is added to the load at beginning of cycle.
When using powdered detergent, remove the detergent
liquid from the compartment. Powdered detergent will not
dispense with detergent liquid.
Detergent compartment
1. Pour the recommended amount of laundry detergent directly into the detergent compartment
before starting your washer.
If an excessive amount of detergent is used it may be mixed with the softener.
2. If color-safe bleach is to be used, it should be added with detergent to the detergent
compartment.
When adding color-safe bleach with detergent, it is best if both laundry products are in the
same form – granular or liquid.
To protect the environment, avoid using excessive amount of detergent when washing
laundry.
03 Washing a load of laundry
WARNING
Pre wash
compartment
Detergent Liquid
WF448AAW-02535B-11_EN.indd Sec11:19WF448AAW-02535B-11_EN.indd Sec11:19 2011-01-13 ¿ÀÀü 10:27:142011-01-13 ¿ÀÀü 10:27:14
20_ Washing a load of laundry
Pre wash compartment
When using the Pre Wash option, detergent should be added to both the Pre Wash
compartment and the detergent compartment. The detergent will automatically be dispensed
during Pre Wash.
If high efficiency (HE) detergent is used, add 1/3 of the recommended amount to the Pre
Wash compartment and 2/3 of the recommended amount to the detergent compartment.
Bleach compartment
(Liquid chlorine bleach only)
1. Add chlorine bleach to the bleach compartment.
DO NOT exceed the MAX FILL line.
2. Avoid splashing or over–filling the compartment.
3. Your Washer automatically dispenses bleach into the tub at
the appropriate time.
4. The dispenser automatically dilutes liquid chlorine bleach
before it reaches the wash load.
Never pour undiluted liquid chlorine bleach directly onto
the load or into the tub. It is a powerful chemical and
can cause fabric damage, such as weakening of the
fibers or color loss, if not used properly.
If you prefer to use color–safe, non–chlorine bleach,
add it to the appropriate detergent compartment.
DO NOT pour color–safe bleach into the Bleach
compartment.
Fabric softener compartment
1. Pour the recommended amount of liquid fabric softener into the softener compartment.
For smaller loads, use less than one capful.
2. Fabric softener should be diluted with water until it reaches MAX FILL in the compartment.
3. The dispenser automatically releases liquid fabric softener at the proper time during the rinse
cycle.
Use the softener compartment ONLY for liquid fabric softeners.
DO NOT use a Downy Ball* in the Fabric softener Compartment of this Washer. It will
not add fabric softener at the appropriate time.
Use the detergent Compartment.
* Brand names are trademarks of their respective manufacturers.
washing a load of laundry
Fabric Softener
compartment
Bleach
compartment
WF448AAW-02535B-11_EN.indd Sec11:20WF448AAW-02535B-11_EN.indd Sec11:20 2011-01-13 ¿ÀÀü 10:27:142011-01-13 ¿ÀÀü 10:27:14
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Samsung WF448AAP Manuel utilisateur

Catégorie
Machines à laver
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues