Kohler K-7517-CP Mode d'emploi

Installation and Care Guide

Bath/Deck Mount Faucet

M product numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

M corresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-73081

1276523-2-A

Tools and Materials

Before You Begin

WARNING: Risk of personal injury. Do not install the bath

faucet in an area where it may inadvertently be used for

support by the bather.

CAUTION: Risk of property damage. Select a cutting tool

appropriate for the deck/rim surface type. Refer to the

surface manufacturer’s instructions for the proper cutting

procedures.

IMPORTANT! Install to a ﬁnished deck only. Cannot be installed

on a rough deck.

IMPORTANT! Do not install the spout or handles to a bath valve

other than the one included. The spout and handles are not

compatible with other valves.

Observe all local plumbing and building codes.

Shut off the water supply.

Protect the surface of the bath deck/rim during installation.

Plumbers Putty

5/8" OD Copper

Tubing (1/2" Nominal)

• 3" (76 mm) Maximum

Reinforcing Material

Plus:

Hex Wrench

5/32" & 5/64"

Rags

Solder

Hacksaw or Tubing Cutter

1276523-2-A 2 Kohler Co.

Roughing-In

1. Prepare the Site

NOTE: To simplify future servicing, install an access panel to reach

the plumbing.

NOTICE: In standard installations, locate the valve bodies 4″ (102

mm) from the spout center, as shown in the diagram. The valve

bodies may be installed anywhere on the deck. Adjust the

dimensions as needed.

Determine the mounting hole locations for the spout and valves.

Refer to the roughing-in dimensions illustrated for proper

placement and diameter.

For a ﬁnished bath deck/rim less than 5/8″ (16 mm) thick: Install

wood reinforcement to the underside of the deck/rim. The

combined thickness of the reinforcing material and the deck/rim

must not exceed 3″ (76 mm).

CAUTION: Risk of property damage. Select a cutting tool

appropriate for the deck/rim surface type. Refer to the

surface manufacturer’s instructions for proper cutting

procedures.

Ø 1-3/4"

(44 mm)

5/8"

(16 mm)

8"

(203 mm)

Min

5/8"

(16 mm)

Min

3"

(76 mm)

Max

5-5/8"

(143 mm)

8-1/4"

(210 mm)

5-3/4"

(146 mm)

10-1/16"

(256 mm)

1-1/2"

Max

4"

(102 mm)

1-1/2"

Max

Kohler Co. 3 1276523-2-A

Prepare the Site (cont.)

NOTICE: Do not exceed 1-1/2″ (38 mm) hole diameters for the

spout and valve body mounting holes. Maximum contact area is

necessary for a successful installation.

Carefully cut mounting holes for the spout and side valves.

Install or relocate the water supplies as needed.

1276523-2-A 4 Kohler Co.

2. Install the Supply Tube

Insert the large O-ring into the large groove in the washer, and

the small O-ring in the small groove on the opposite side of the

washer.

With the large O-ring in the washer and facing down, position

the washer over the mounting hole. Carefully insert the supply

tube assembly through the washer and mounting hole.

Orient the tabs on the plate up. Slide the plate onto the supply

tube assembly from underneath until ﬂush with the underside of

the deck/rim. Secure with the screws. Slide the ﬂat washer onto

the supply tube assembly, then wrench tighten the nut.

Install the pipe plug (not shown) into the top of the supply tube.

Nut

Screw

Plate

Washer

Small O-Ring

Large O-Ring

Grooved Washer

Supply Tube

Kohler Co. 5 1276523-2-A

3. Install the Valve Bodies

Measure the thickness of the ﬁnished deck. If the deck is less than

1-1/4″ (32 mm), use a dished washer. If the deck is more than

1-1/4″ (32 mm) thick, you may use or discard the dished washer.

Apply plumbers putty or sealant to the underside of a collar.

Partially thread two screws into a threaded ring as shown.

Assemble a threaded ring, washer, and dished washer (if used)

down one of the valve bodies as far as possible.

From underneath, insert the valve body through the mounting

hole.

From above, thread the collar onto the valve until it stops.

Lift up the valve body to expose the collar setscrew. Then tighten

the collar setscrew.

Repeat for the second valve body.

Valve Body

Dished Washer

Washer

Threaded Ring

Collar

Setscrew

1276523-2-A 6 Kohler Co.

4. Cut the Tubing

If the tee is not attached to the spout tube, attach it now.

Measure the distance between the tee inlets and each valve body

outlet.

Cut the tubing to ﬁt.

Pivot the valve bodies, and install the two pieces of tubing.

Conﬁrm the tubes are cut to the correct lengths.

Valve Outlet

Tee

Tee Inlet

Kohler Co. 7 1276523-2-A

5. Secure the Valves

Turn the threaded ring up each valve body until ﬁnger tight, then

use a Phillips screwdriver to securely tighten the threaded ring

screws.

Clean away any excess plumbers putty from the deck.

Connect the hot and cold valve bodies to the appropriate water

supply lines.

Solder the connections.

Hot

Solder

Cold

Screw

1276523-2-A 8 Kohler Co.

6. Install the Handles

NOTE: Lever handles should be parallel to the bath rim when the

handles are in the OFF position. The handles should point toward

the bath when in the ON position.

Align a handle assembly onto the collar. Press down and turn the

bonnet to secure the handle assembly.

Repeat for the second handle.

Open and close the handles to conﬁrm alignment and

unobstructed operation.

Kohler Co. 9 1276523-2-A

7. Complete the Installation

Make sure the faucet valves are closed.

Open the water supplies to the faucet.

Check for leaks, and repair as needed.

Close the water supplies.

Remove the plug from the supply tube.

Press the O-ring into the groove in the underside of the

escutcheon.

Install the spout and escutcheon onto the supply tube.

Align the spout, and secure with the setscrew.

Press the plug button into the setscrew hole.

Turn the water supplies on.

Run water through the spout, and check for leaks.

Plug Button

Setscrew

O-Ring

Escutcheon

1276523-2-A 10 Kohler Co.

Care and Cleaning

For best results, keep the following in mind when caring for your

KOHLER product:

•

Use a mild detergent such as liquid dishwashing soap and warm

water for cleaning. Do not use abrasive cleaners that may scratch

or dull the surface.

•

Carefully read the cleaner product label to ensure the cleaner is

safe for use on the material.

•

Always test your cleaning solution on an inconspicuous area

before applying to the entire surface.

•

Do not allow cleaners to sit or soak on the surface.

•

Wipe surfaces clean and rinse completely with water immediately

after cleaner application. Rinse and dry any overspray that lands

on nearby surfaces.

•

Use a soft, dampened sponge or cloth. Never use an abrasive

material such as a brush or scouring pad to clean surfaces.

For detailed cleaning information and products to consider, visit

www.kohler.com/clean. To order Care & Cleaning information, call

1-800-456-4537.

Warranty

KOHLER

®

Faucet Lifetime Limited Warranty

Kohler Co. warrants its Faucets* manufactured after January 1, 1997, to

be leak and drip free during normal residential use for as long as the

original consumer purchaser owns his or her home. If the Faucet

should leak or drip during normal use, Kohler Co. will, free of charge,

mail to the purchaser the cartridge necessary to put the Faucet in good

working condition. This warranty applies only to Kohler Faucets

installed in the United States of America, Canada or Mexico (″North

America″).

Kohler Co. also warrants all other aspects of the faucet or accessories

(″Faucet″)*, (except gold, non-Vibrant

®

, non-chrome ﬁnishes) to be free

of defects in material and workmanship during normal residential use

for as long as the original consumer purchaser owns his or her home.

This warranty applies only to Kohler Faucets installed in North

America. If a defect is found in normal residential use, Kohler Co. will,

at its election, repair, provide a replacement part or product, or make

appropriate adjustment. Damage to a product caused by accident,

misuse, or abuse is not covered by this warranty. Improper care and

Kohler Co. 11 1276523-2-A

Warranty (cont.)

cleaning will void the warranty**. Proof of purchase (original sales

receipt) must be provided to Kohler Co. with all warranty claims.

Kohler Co. is not responsible for labor charges, installation, or other

incidental or consequential costs. In no event shall the liability of

Kohler Co. exceed the purchase price of the Faucet.

If the Faucet is used commercially or is installed outside of North

America, or if the ﬁnish is gold, non-Vibrant or a painted or powder

coated color ﬁnish, Kohler Co. warrants the Faucet to be free from

defects in material and workmanship for one (1) year from the date the

product is installed, under Kohler Co.’s standard one-year limited

warranty.

If you believe that you have a warranty claim, contact Kohler Co.,

either through your Dealer, Plumbing Contractor, Home Center or

E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444

Highland Drive, Kohler, WI 53044, USA. Please be sure to provide all

pertinent information regarding your claim, including a complete

description of the problem, the product, model number, color, ﬁnish,

the date the product was purchased and from whom the product was

purchased. Also include your original invoice. For other information,

or to obtain the name and address of the service and repair facility

nearest you, call 1-800-4-KOHLER (1-800-456-4537) from within the

USA and Canada, and 001-800-456-4537 from within Mexico, or visit

www.kohler.com within the USA, www.ca.kohler.com from within

Canada, or www.mx.kohler.com in Mexico.

KOHLER CO. AND/OR SELLER ARE PROVIDING THESE

WARRANTIES IN LIEU OF ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. KOHLER CO. AND/OR

SELLER DISCLAIM ALL LIABILITY FOR SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states/provinces do not

allow limitations of how long an implied warranty lasts or the

exclusion or limitation of such damages, so these limitations and

exclusions may not apply to you. This warranty gives the consumer

speciﬁc legal rights. You may also have other rights that vary from

state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

*Trend

®

faucets, MasterShower

®

tower, BodySpa systems and

components; WaterHaven

®

tower, systems and components; Tripoint

®

faucets, Polished Gold, non-Vibrant and painted or powder coated

ﬁnishes, ﬁttings; all items within the ″Fixture Related″ section of the

Kohler Faucets Price Book, drains, Duostrainer

®

sink strainers,

1276523-2-A 12 Kohler Co.

Warranty (cont.)

soap/lotion dispensers, Moxie

®

Wireless Speaker; and faucets used in

commercial settings, and outside North America, are covered by

Kohler Co.’s one-year limited warranty.

**Never use cleaners containing abrasive cleansers, ammonia, bleach,

acids, waxes, alcohol, solvents or other products not recommended for

chrome. This will void the warranty.

Warranty

For Mexico

KOHLER CO.

It is recommended that at the time of purchase, you verify that all

accessories and components are complete in this package.

This Kohler product is warranted to be free of defects in material and

workmanship for one (1) year from the date of purchase as shown on

the invoice or receipt.

1. Kohler Co. will only service its commercialized products through its

authorized distributors.

2. To obtain warranty service, please present the invoice and

corresponding warranty.

3. Through its authorized distributors, Kohler Co. promises to repair

the defective product or provide a new replacement or an equivalent

model (in those cases that the model has been discontinued) when the

product is beyond repair, without any charge to the consumer.

4. The time of repair will not exceed six (6) weeks commencing on the

date the product is received.

5. It is recommended that the consumer save the invoice or receipt as

additional protection, as it may substitute the warranty in the case that

there is a discrepancy in the validity of the warranty.

EXCEPTIONS AND RESTRICTIONS

The Warranty will not be valid in the following cases:

1. When the product is not operated in accordance with the

instructions concerning use and operation set forth in the owner’s

manual or installation instructions, and when the recommendations

and warnings included are not observed.

2. When the product has been modiﬁed or dismantled partially or

totally; or has been used in a negligent fashion and as a consequence

has suffered damages attributable to the consumer, individual, or

Kohler Co. 13 1276523-2-A

Warranty (cont.)

hardware not authorized by Kohler Co.

3. This warranty does not cover the damages as a result of disaster

such as ﬁre or acts of God, including ﬂooding, earthquake, or electric

storms, etc. To obtain a list of distributors in your area where you can

exercise your rights under this warranty, please call 001-800-456-4537.

KOHLER CO., KOHLER, WI 53044 U.S.A.

IMPORTER:

COMERCIALIZADORA INTERCERAMIC, S.A. DE C.V.

AV. CARLOS PACHECO NO. 7200, COL. MADERA 65

CHIHUAHUA, CHIH., MEXICO C.P. 31060

R.F.C. CIN141022IE9

TEL: 52 (614) 429-11-11

IMPORTER:

GAMA MATERIALES Y ACEROS, S.A. DE C.V.

AVE LOS ANGELES NO. 1800

COL VALLE DEL NOGALAR, SAN NICOLAS DE LOS GARZA

N.L. MEXICO

R.F.C. GMA901220U11

TEL: 81-1160-5500

1276523-2-A 14 Kohler Co.

Guide d’installation et d’entretien

Robinet à montage sur baignoire/plateau

Outils et matériel

Avant de commencer

AVERTISSEMENT: Risque de blessures. Ne pas installer le

robinet de baignoire dans un endroit où la personne dans le

bain peut s’y appuyer par inadvertance.

ATTENTION: Risque de dommages matériels. Choisir un

outil de coupe adapté à la surface du plateau/rebord à

découper. Voir les instructions de découpage dans les

instructions du fabricant de la surface.

IMPORTANT! Installer sur un plateau ﬁni seulement. Ne peut pas

être installé sur un plateau brut.

IMPORTANT! Ne pas installer le bec ou les poignées sur une

vanne de baignoire autre que celle fournie. Le bec et les poignées ne

sont pas compatibles avec d’autres vannes.

Respecter tous les codes de plomberie et de bâtiment locaux.

Fermer l’arrivée d’eau.

Mastic de plombier

Tube en cuivre de

dia. ext. 5/8" (1/2" nominal)

• Matériau de renfort de

3" (76 mm) maximum

Plus:

Clé hexagonale

5/32" et 5/64"

Chiffons

Brasure

Scie à métaux ou

coupe-tube

Kohler Co. Français-1 1276523-2-A

Avant de commencer (cont.)

Protéger la surface du plateau/rebord de la baignoire durant

l’installation.

1276523-2-A Français-2 Kohler Co.

Raccordement

1. Préparer le site

REMARQUE: Pour simpliﬁer les interventions ultérieures, prévoir

un panneau d’accès à la plomberie.

AVIS: Dans les installations standard, placer les corps de vannes à

4″ (102 mm) du centre du bec, comme indiqué sur le schéma. Les

corps de vannes peuvent être installés n’importe où sur le plateau.

Ajuster les dimensions selon les besoins.

Déterminer l’emplacement des trous de ﬁxation pour le bec et les

vannes. Voir les emplacements et diamètres corrects sur le plan de

raccordement coté.

Plateau/rebord de baignoire ﬁni de moins de 5/8″ (16 mm)

d’épaisseur : Installer un renfort en bois sur le dessous du

plateau/rebord. L’épaisseur combinée du renfort et du

plateau/rebord ne doit pas dépasser 3″ (76 mm).

ATTENTION: Risque de dommages matériels. Choisir un

outil de coupe adapté à la surface du plateau/rebord à

découper. Se reporter aux instructions du fabricant de la

surface pour les procédures de découpage adéquates.

Ø 1-3/4"

(44 mm)

5/8"

(16 mm)

8"

(203 mm)

Min

5/8"

(16 mm)

Min

3"

(76 mm)

Max

5-5/8"

(143 mm)

8-1/4"

(210 mm)

5-3/4"

(146 mm)

10-1/16"

(256 mm)

1-1/2"

Max

4"

(102 mm)

1-1/2"

Max

Kohler Co. Français-3 1276523-2-A

Préparer le site (cont.)

AVIS: Ne pas dépasser des diamètres de trous de 1-1/2″ (38 mm)

pour les trous de montage du bec et des corps de vannes. La surface

de contact doit être maximale pour assurer installation réussie.

Avec précaution, découper les trous de ﬁxation pour le bec et les

vannes latérales.

Installer ou déplacer les arrivées d’eau selon les besoins.

1276523-2-A Français-4 Kohler Co.

2. Installer le tube d’arrivée

Insérer le grand joint torique dans la grande gorge de la rondelle

et le petit joint torique dans la petite gorge située sur le côté

opposé de la rondelle.

Avec le grand joint torique dans la rondelle tourné vers le bas,

placer la rondelle sur le trou de montage. Insérer avec précaution

le tube d’arrivée dans la rondelle et le trou de montage.

Placer les languettes de la plaque vers le haut. Enﬁler la plaque

sur l’ensemble du tube d’arrivée à partir du dessous jusqu’à ce

qu’il soit à ras du dessous du plateau/rebord. Sécuriser avec les

vis. Enﬁler la rondelle plate sur l’ensemble du tube d’arrivée, puis

serrer l’écrou avec une clé.

Installer le bouchon du tuyau (non illustré) dans le dessus du

tube d’arrivée.

Écrou

Vis

Plaque

Rondelle

Petit joint torique

Grand joint torique

Rondelle à gorge

Tube d'arrivée

Kohler Co. Français-5 1276523-2-A

3. Installer les corps de vannes

Mesurer l’épaisseur du plateau ﬁni. Si le plateau mesure moins de

1-1/4″ (32 mm), utiliser une rondelle bombée. Si l’épaisseur du

plateau est supérieure à 1-1/4″ (32 mm), la rondelle bombée peut

être utilisée ou jetée.

Appliquer du mastic de plombier ou du matériau d’étanchéité sur

le dessous d’un collier.

Visser partiellement deux vis dans un anneau ﬁleté comme

illustré.

Assembler un anneau ﬁleté, une rondelle et une rondelle bombée

(le cas échéant) vers le bas des corps de vannes, aussi loin que

possible.

À partir du dessous, insérer le corps de vanne à travers le trou de

montage.

À partir du dessus, enﬁler le collier sur la vanne, jusqu’à ce qu’il

s’arrête.

Lever le corps de vanne pour exposer la vis d’arrêt du collier.

Serrer ensuite la vis d’arrêt du collier.

Corps de robinet

Rondelle bombée

Rondelle

Collier

Vis d'arrêt

L'anneau fileté

1276523-2-A Français-6 Kohler Co.

La page charge ...

Kohler K-7517-CP Mode d'emploi

Kohler K-7517-CP Mode d'emploi

dans d''autres langues

Documents connexes