Simplicity 040547-00 Guide d'installation

Installation and Operation Manual

17kW 20kW

Single Phase Air-Cooled

Standby Generator System

This generator is rated in accordance with UL (Underwriters Laboratories) 2200 (stationary engine generator

assemblies) and CSA (Canadian Standards Association) standard C22.2 No. 100-4 (motors and generators).

Milwaukee, WI, USA.

80020100USCN

Revision ( E )

™

Thank you for purchasing this quality-built Briggs & Stratton® standby generator. We are pleased that you’ve

placed your confidence in the Briggs & Stratton brand. When operated and maintained according to the

instructions in the operator’s manual, your standby generator will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with residential

generator systems and how to avoid them. This generator system is designed and intended only for use as an

optional home standby system that provides an alternate source of electric power and to serve loads such as

heating, refrigeration systems, and communication systems that, when stopped during any power outage, could

cause discomfort or inconvenience. Save these original instructions for future reference.

This generator system requires professional installation before use. The installer should follow the

instructions completely.

Where to Find Us

You never have to look far to find support and service for your generator. Consult your Yellow Pages. There are

many Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact

Briggs & Stratton Customer Service by phone at 800 732-2989 between 8:00 AM and 5:00 PM CT., or click on

Find a Dealer at BRIGGSandSTRATTON.COM, which provides a list of authorized dealers.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase

issues.

DATE OF PURCHASE

GENERATOR

Model Number

Serial Number

Model Number

Model Revision

Serial Number

ENGINE

3

Important Safety Instructions........................4

Installation ....................................7

Owner Responsibilities.........................................7

Installing Dealer/Contractor Responsibilities ........................7

Unpacking Precautions ........................................8

Delivery Inspection............................................8

Shipment Contents............................................8

Generator Placement ..........................................9

REDUCE THE RISK OF CARBON MONOXIDE POISONING.............10

Other General Location Guidelines...............................11

REDUCE THE RISK OF FIRE....................................12

Electrical and Fuel Inlet Locations ...............................14

Lifting the Generator .........................................15

Concrete Anchoring of Unit ....................................15

Access Ports ...............................................16

The Gaseous Fuel System .....................................18

Fuel Consumption ...........................................19

Fuel Pressure ...............................................19

Power Loss ................................................19

Fuel Pipe Sizing .............................................19

Fuel Conversion .............................................20

System Connectors ..........................................21

Communication Connections ...................................22

Generator AC Connection System ...............................22

Grounding the Generator ......................................23

Utility Circuit Connection ......................................23

Generator Power Connection ...................................23

Transfer Switch Communication ................................23

System Control Panel.........................................24

Final Installation Considerations ................................29

Initial Start-up (No Load)......................................30

Electronic Governor System ...................................31

Operation .................................... 32

Automatic Operation Sequence .................................32

Setting Exercise Timer ........................................32

Installation Inspection ........................................32

Schematic / Wiring Diagrams ...................... 34

Operator’s Section .............................. 38

Controls ..................................... 38

Access Panels ..............................................40

Operation .................................... 42

Engine Oil..................................................42

Battery ....................................................42

15 Amp Fuse ...............................................42

Automatic Operation Sequence .................................42

Maintenance .................................. 43

Service Code Detection System .................................43

Generator Maintenance .......................... 46

Engine Maintenance..........................................48

Adjust Valve Lash............................................48

Service Air Cleaner...........................................50

Service Spark Plugs..........................................51

Troubleshooting................................ 52

Generator Specifications.......................... 53

Engine Specifications ............................ 53

Common Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Table Of Contents

4

Save These Instructions

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide could result in death,

serious injury, headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that

will not accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open

garage doors or other openings that can allow

exhaust gas to enter inside or be drawn into a

potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed

and maintained indoors according to the

manufacturer’s instructions/recommendations.

Smoke alarms cannot detect carbon monoxide gas.

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol

may be used to represent the type of hazard. The signal

word NOTICE is used to address practices not related to

personal injury.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

The manufacturer cannot possibly anticipate every

possible circumstance that might involve a hazard.

The warnings in this manual, and the tags and decals

affixed to the unit are, therefore, not all-inclusive. If you

use a procedure, work method or operating technique

that the manufacturer does not specifically recommend,

you must satisfy yourself that it is safe for you and

others. You must also make sure that the procedure,

work method or operating technique that you choose

does not render the generator system unsafe.

Explosion

Fire

Electrical Shock

Rotating Parts

Hot Surface

Toxic Fumes

Chemical BurnExplosive PressureAuto Start

Lift Hazard

Read Manual

WARNING The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING Certain components in this product

and related accessories contain chemicals known to

the State of California to cause cancer, birth defects, or

other reproductive harm. Wash hands after handling.

WARNING Storage batteries give off explosive

hydrogen gas during recharging.

Slightest spark will ignite hydrogen

and cause explosion, resulting in

death, serious injury and/or property damage. Battery

electrolyte fluid contains acid and is extremely caustic.

Contact with battery contents could cause severe

chemical burns. A battery presents a risk of electrical shock

and high short circuit current.

• DO NOT dispose of battery in a fire. Recycle battery.

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, rubber

boots and rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

5

WARNING Generator produces hazardous

voltage. Failure to properly ground generator

could result in electrocution.Failure to isolate

generator from utility power could result in death

or serious injury to electric utility workers due to

backfeed of electrical energy.

• When using generator for backup power, notify

utility company.

• DO NOT touch bare wires or bare receptacles.

• DO NOT use generator with electrical cords which

are worn, frayed, bare or otherwise damaged.

• DO NOT handle generator or electrical cords while

standing in water, while barefoot, or while hands or

feet are wet.

• If you must work around a unit while it is operating,

stand on an insulated dry surface to reduce the risk

of a shock hazard.

• DO NOT allow unqualified persons or children to

operate or service generator.

• In case of an accident caused by electrical shock,

immediately shut down the source of electrical

power and contact the local authorities. Avoid

direct contact with the victim.

• Despite the safe design of the generator, operating

this equipment imprudently, neglecting its

maintenance or being careless could cause possible

injury or death.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you

are physically or mentally fatigued.

• Before performing any maintenance on the

generator, disconnect the battery cable indicated

by a NEGATIVE, NEG or (-) first. When finished,

reconnect that cable last.

• After your system is installed, the generator may crank

and start without warning any time there is a power

failure. To prevent possible injury, always set the

generator’s system switch to OFF, remove the service

disconnect from the disconnect box AND remove the

15 Amp fuse BEFORE working on the equipment.

WARNING Propane and Natural Gas are extremely

flammable and explosive, which could cause

burns, fire or explosion resulting in death,

serious injury and/or property damage.

• Install the fuel supply system according to NFPA 37

and other applicable fuel-gas codes.

• Before placing the generator into service, the fuel

system lines must be properly purged and leak tested.

• After the generator is installed, you should inspect

the fuel system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or

other explosive conditions exist.

• DO NOT smoke around the generator. Wipe up any

oil spills immediately. Ensure that no combustible

materials are left in the generator compartment. Keep

the area near the generator clean and free of debris.

WARNING Hazardous Voltage - Contact with

power lines could cause electric shock

or burns, resulting in death or serious

injury.Lifting Hazard / Heavy Object -

Could result in serious injury.

• If lifting or hoisting equipment is used, DO NOT

contact any power lines.

• DO NOT lift or move generator without assistance.

• Use lifting pipes as described in Lifting the Generator.

• DO NOT lift unit by roof as damage to generator

will occur.

6

WARNING Starter and other rotating parts could

entangle hands, hair, clothing, or accessories

resulting in serious injury.

• NEVER operate generator without protective

housings, covers, or guards in place.

• DO NOT wear loose clothing, jewelry or anything that

could be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

• Before servicing, remove 15 Amp fuse from control

panel and disconnect Negative (NEG or -) battery

cable.

CAUTION Installing the 15A fuse could cause

the engine to start at any time without warning

resulting in minor or moderate injury.

• Observe that the 15 Amp fuse has been removed

from the control panel for shipping.

• DO NOT install this fuse until all plumbing and wiring

has been completed and inspected.

CAUTION Excessively high operating speeds

could result in minor injury and/or equipment

damage. Excessively low speeds impose a heavy

load on generator.

• DO NOT tamper with governed speed. Generator

supplies correct rated frequency and voltage when

running at governed speed.

• DO NOT modify generator in any way.

NOTICE Improper treatment of generator could

damage it and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, contact

your authorized dealer.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating

air is critical to correct generator operation.

• The access panels/doors must be installed

whenever the unit is running.

• DO NOT expose generator to excessive moisture,

dust, dirt, or corrosive vapors.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you

are physically or mentally fatigued.

• DO NOT start engine with air cleaner or air cleaner

cover removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as a step.

Stepping on the unit could cause stress and break parts.

This may result in dangerous operating conditions from

leaking exhaust gases, fuel leakage, oil leakage, etc.

• If connected devices overheat, turn them off and

disconnect them from generator.

Shut off generator

and contact an authorized deaker

if

- electrical output is lost;

- equipment sparks, smokes, or emits flames;

- unit vibrates excessively;

- unit makes unusual noises.

WARNING

Exhaust heat/gases could ignite

combustibles or structures resulting in

death, serious injury and/or property

damage. Contact with muffler area could

cause burns resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust

gases.

• Allow equipment to cool before touching.

• Exhaust outlet side of weatherproof enclosure must

have at least 5 ft. (1.5 m) minimum clearance from

any structure, shurbs, trees or any kind of vegetation.

• Standby generator weatherproof enclosure must be at

least 5 ft. (1.5 m) from windows, doors, any wall opening,

shrubs or vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must

have a minimum of 5 ft. (1.5 m) overhead clearance

from any structure, overhang or trees.

• DO NOT place weatherproof enclosure under a deck

or other type of structure that may confine airflow.

• Use only flexible fuel line provided. Connect

provided fuel line to generator, DO NOT use with or

substitute any other flexible fuel line.

• Smoke detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Carbon monoxide

alarms cannot detect smoke.

• Keep at least minimum distances shown in General

Location Guidelines to insure for proper generator

cooling and maintenance clearances.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any

forest-covered, brush-covered, or grass-covered

land unless the exhaust system is equipped with

a spark arrester, as defined in Section 4442,

maintained in effective working order. Other states

or federal jurisdictions may have similar laws

Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester designed

for the exhaust system installed on this engine.

• Replacement parts must be the same and installed

in the same position as the original parts.

7

Installation

Equipment Description

This product is only for use as an optional generator

system which provides an alternate source of electric

power and to serve loads such as heating, refrigeration

systems, and communication systems that, when stopped

during any power outage, could cause discomfort or

inconvenience.

NOTICE This product does NOT qualify for either an

emergency standby or legally required standby system

as defined by NFPA 70 (NEC).

• Emergency generator systems are intended to

automatically supply illumination, power, or both,

to designated areas and equipment in the event of

failure of the normal supply. Emergency systems

may also provide power for such functions as

ventilation where essential to maintain life, where

current interruption of the normal supply would

produce serious life safety or health hazards.

• Legally Required standby generator systems

are intended to automatically supply power

to selected loads in the event of failure of the

normal source which could create hazards or

hamper rescue or fire-fighting operations.

Every effort has been made to ensure that information

in this manual is accurate and current. However, we

reserve the right to change, alter, or otherwise improve

the product and this document at any time without prior

notice.

Only current licensed electrical and plumbing professionals

should attempt standby generator system installations.

Installations must strictly comply with all applicable codes,

industry standards, laws and regulations.

Owner Responsibilities

• Read and follow the instructions given in the

operator’s manual.

• Follow a regular schedule in maintaining, caring

for and using your generator, as specified in the

operator’s manual.

• Carbon monoxide detector(s) MUST be installed

and maintained indoors according to the

manufacturer’s instructions/recommendations.

Smoke alarms cannot detect carbon monoxide

gas.

• Smoke detector(s) MUST be installed

and maintained indoors according to the

manufacturer’s instructions/ recommendations.

Carbon monoxide alarms cannot detect smoke.

If you have questions about intended use, ask your

installer or dealer or call 800 732-2989 between

8:00 AM and 5:00 PM CT.

Installing Dealer/Contractor

Responsibilities

• Read and observe the safety rules.

• Install only an UL approved transfer switch that is

compatible with the generator.

• Read and follow the instructions given in this

installation and start-up manual.

• Installation must strictly comply with all applicable

codes, industry standards, laws, and regulations.

• Allow sufficient room on all sides of the generator

for maintenance and servicing.

Cold Weather Kit

If operating the generator below 30°F (-1°C), it is HIGHLY

RECOMMENDED that a Model 6404 Cold Weather Kit

be installed.

These items are available at your local servicing dealer.

For cold weather areas (below 0°F (-18°C)) it is also

recommended that a BCI, Size 75, wet lead-acid

battery be used of 630 CCA minimum.

If you need more information on this matter, please call

800 732-2989 between 8:00 AM and 5:00 PM CT.

30°F (-1°C)

8

Unpacking Precautions

The unit is shipped ready for installation. Avoid

damage from dropping, bumping, collision, etc. Store

and unpack carton with the proper side up, as noted

on the shipping carton.

Delivery Inspection

After removing the carton, carefully inspect the

generator for any damage that may have occurred

during shipment.

If loss or damage is noted at time of delivery, have

the person(s) making delivery note all damage on the

freight bill and affix his signature under the consignor’s

memo of loss or damage. If loss or damage is noted

after delivery, separate the damaged materials

and contact the carrier for claim procedures. Parts

damaged in shipping are not warranted.

Shipment Contents

The standby generator system is supplied with:

• Oil (5W30 Synthetic)

• Flexible steel fuel line

• Installation/Operation manual

• Product and emissions warranty booklet

• Spare access roof keys

• Spare 15 Amp ATO-type fuse

• Tamper proof plug

Not included:

• Carbon monoxide detector(s)

• Smoke detector(s)

• Starting battery

• Connecting wire and conduit

• Fuel supply valves/plumbing

• Crane, lifting straps, chains or cables

• Two 60” lengths of 3/4” nominal minimum

scheduled 40 steel pipe (NOT conduit)

• Torque screwdriver, 5 to 50 inch-pound range

• Voltage/frequency meter

9

Generator Placement

Before installing generator, consult with home owner

and convey the following requirements, which must be

satisfied before the installation is complete.

There are two equally important safety concerns in

regards to carbon monoxide poisoning and fire. There

are also several general location guidelines that must be

met before the installation in considered complete.

Exhaust Side of the Generator

A - Exhaust outlet side of weatherproof enclosure

B - Air inlet side of weatherproof enclosure

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide could result in death

serious injury, headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that

wil not accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open

garage doors or other openings that can allow

exhaust gas to enter inside or be drawn into a

potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed

and maintained indoors according to the

manufacturer’s instructions/recommendations.

Smoke alarms cannot detect carbon monoxide gas.

B

A

B

10

All fossil fuel burning equipment, such as standby

generators, contains carbon monoxide (CO) gas in

the engine exhaust. CO gas is odorless, colorless and

tasteless and is unlikely to be noticed until a person is

overcome. CO gas can kill you so it is required that the

following is included as part of the installation:

• Install generator outdoors in an area that will not

accumulate deadly exhaust gas.

• DO NOT install generator where exhaust gas

could accumulate and enter inside or be drawn

into a potentially occupied building or structure.

• By law it is required in many states to have a

Carbon Monoxide (CO) detector in operating

condition in your home. Carbon monoxide

detector(s) (A) MUST be installed and maintained

indoors according to the manufacturer’s instructions

/ recommendations. A CO monitor is an electric

device that detects hazardous levels of CO. When

there is a buildup of CO, the monitor will alert the

occupants by flashing visual indicator light and

alarm. Smoke alarms cannot detect CO gas.

• Your neighbor(s) home may be exposed to the engine

exhaust from your standby generator and must be

considered when installing your standby generator.

• Ensure exhaust gas is kept away from:

B - windows

C - doors

D - ventilation intakes

E - soffit vents

F - garage doors

G - crawl spaces or other openings that can allow

exhaust gas to enter inside or be drawn into a

potentially occupied building or structure.

Placement of Standby Generator to REDUCE THE RISK OF CARBON MONOXIDE POISONING

The arrows in the figure below point to POTENTIAL points of entry for Carbon Monoxide Gas.

A

F

C

D

B

G

E

F

C

D

B

E

G

11

• Direct the standby generator exhaust away from

or parallel to the building or structure. DO NOT

direct the generator exhaust towards a potentially

occupied building, structure, windows, doors,

ventilation intakes, soffit vents, crawl spaces,

open garage doors or other openings where

exhaust gas could accumulate and enter inside

or be drawn into potentially occupied building or

structure.

• DO NOT place standby generator in any area

where leaves or debris normally accumulates.

Position standby generator in an area where

winds will carry the exhaust gas away from any

potentially occupied building or structure.

Other General Location Guidelines

• Place the standby generator in a prepared

location that is flat and has provisions for water

drainage.

• Install the standby generator in a location where

sump pump discharge, rain gutter downspouts,

roof run-off, landscape irrigation, or water

sprinklers will not flood the unit or spray the

enclosure and enter any air inlet or outlet

openings.

• Install the standby generator where it will not

affect or obstruct and services including covered,

concealed and underground, such as telephone,

electric, fuel (natural gas/ LPG vapor), irrigation,

air conditioning, cable, septic, sewer, well and so

forth.

• Install the standby generator where leaves, grass,

snow, etc. will not obstruct air inlet and outlet

openings. If prevailing winds will cause blowing or

drifting, you may need to construct a windbreak to

protect the unit.

ENGINE

EXHAUST

STANDBY

GENERATOR

12

Placement of Standby Generator to

REDUCE THE RISK OF FIRE

Requirements:

NFPA 37 2010, section 4. 1. 4, Engines Located

Outdoors. Engines, and their weatherproof housings

if provided, that are installed outdoors shall be located

at least 1.5m (5 ft) from openings in walls and at least

1.5 m (5 ft) from structures having combustible walls. A

minimum separation shall not be required where either of

the following conditions exist:

1. The adjacent wall of the structure has a fire

resistance rating of at least 1 hour.

2. The weatherproof enclosure is constructed

of noncombustible materials and it has been

demonstrated that a fire within the enclosure will not

ignite combustible materials outside the enclosure. *

Annex A Explanatory Material

A.4.1.4 (2) Means of demonstrating compliance

are by means of full-scale fire tests or by calculation

procedures, such as those given in NFPA 555, Guide on

Methods for Evaluating Potential for Room Flashover.

To comply with condition 2 above the weatherproof

enclosure has been constructed completely of non-

combustible materials and full-scale fire tests have been

conducted to demonstrate that a fire within the enclosure

will not ignite combustible materials outside the enclosure.

WARNING

Exhaust heat/gases could ignite

combustibles or structures resulting in death,

serious injury and/or property damage.

• Exhaust outlet side of weatherproof enclosure must

have at least 5 ft. (1.5 m) minimum clearance from any

structure, shrubs, trees or any kind of vegetation.

• Standby generator weatherproof enclosure must be at

least 5 ft. (1.5 m) from windows, doors, any wall opening,

shrubs or vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must have

a minimum of 5 ft. (1.5 m) overhead clearance from

any structure, overhang or trees.

• DO NOT place weatherproof enclosure under a deck

or other type of structure that may confine airflow.

• Use only flexible fuel line provided. Connect provided

fuel line to generator, DO NOT use with or substitute

any other flexible fuel line.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot

detect smoke.

• DO NOT place weatherproof enclosure in manner

other than shown in illustrations.

Legend for Generator Locations to reduce the risk

of fire.

A Standby weatherproof enclosure must be at least 5 ft

(1.5 m) from windows, doors, any wall opening, shrubs

or vegetation over 12 inches (30.5 cm) in height.

B Exhaust outlet side of weatherproof enclosure must

have at least 5 ft (1.5 m) minimum clearance from any

structure, shrubs, trees or any kind of vegetation.

C Standby weatherproof enclosure must have a

minimum of 5 feet (1.5 m) overhead clearance from

any structure, overhang or trees.

D Standby Weatherproof enclosure must have a

minimum of 18 inches (45.7 cm) clearance from any

structures with or without a fire rating.

NOTICE DO NOT place weatherproof enclosure under a

deck or other type of covered structure that may confine

airflow.

NOTICE The figures below demonstrate the minimum

installation distances allowed to structures and items

shown in legend.

D

A

B A

C

A

B

Standby

5 ft (1.5 m)

Exhaust

Direction

18 in.

(45.7 cm) min.

Standby

Exhaust

Direction

5 ft (1.5 m)

A

13

Electrical and Fuel Inlet Locations

The 3/4 inch N.P.T. fuel inlet connector (A) and

electrical inlet location (B) is shown below.

A ½ inch knock-out is provided for the electrical

inlet. This inlet may be enlarged or supplemented to

accommodate a maximum conduit size of 1 ½ inches.

Ensure that the installed conduit(s) enter the unit in the

zone (C) shown in the drawing such that they properly

enter the electrical box and do not interfere with the

fully opened roof.

The standby generator is supplied with a base that,

unless mandated by local code, does not require a

concrete slab.

A

B

C

14

Lifting the Generator

The generator weighs more than 500 pounds (227 kg).

Proper tools, equipment and qualified personnel should be

used in all phases of handling and moving the generator.

Two 60” lengths of 3/4’” nominal minimum scheduled

40 steel pipe (A), supplied by the installer, are required

to lift the generator manually. Insert pipes through the

lifting holes (B) located near the unit’s base.

You may also lift the unit using a “hook and hoist”

method attached to the lifting pipes, provided that you

use a spreader bar to ensure that the chains or cables

DO NOT touch the generator’s roof.

WARNING Hazardous Voltage - Contact with

power lines could cause electric shock

or burns, resulting in death or serious

injury.Lifting Hazard / Heavy Object - Could result in

serious injury.

• If lifting or hoisting equipment is used, DO NOT

contact any power lines.

• DO NOT lift or move generator without assistance.

• Use lifting pipes as described in Lifting the

Generator.

• DO NOT lift unit by roof as damage to generator will occur.

In areas determined to be hurricane prone, it is

recommended to anchor the standby generator to

concrete. The concrete anchors must be rated to hold

800 lbs ( kg). There are four (C) 7/16 inch hole locations

around the base of generator in which to anchor the unit.

Concrete Anchoring of Unit

NOTICE Unless mandated by local or state code, a

concrete slab is not required.

A

B

C

C C

C

1257 mm

49.5”

600 mm

23.6”

1181 mm

46.5”

710 mm

28”

15

Access Ports

The generator is equipped with an enclosure that has

several access panels, as shown.

The access panels and the components located

behind them are listed below:

A - Roof (Control Panel, air filter, oil dipstick, and circuit

breaker)

B - Front Access Panel (oil drain and oil filter)

C - Battery Panel (battery and generator data label)

D - Rear Access Panel (fuel regulator, fuel selector, and

engine starter)

E - Control Panel Cover (field wiring and control wires)

Each generator is shipped with a set of identical keys.

These keys fit in the lock on the front removable panel.

The roof must be unlocked in order for it to open.

A

B

D

E

C

16

To open roof:

1. Insert key into lock (A) of front panel. Gently push

down on roof above the lock to aid in turning the

key. Turn key one quarter turn clockwise.

2. Lift roof to the open position.

To remove front panel:

1. Remove the two bolts (B) that secure the panel to the unit.

2. Lift panel to remove from unit.

To secure front panel:

1. Place panel in unit.

2. Secure the panel with two bolts.

To remove rear panel:

1. Ensure the roof is in the open position.

2. Remove the two bolts (C) that secure the panel to

the unit.

3. Lift panel to remove from unit.

To secure rear panel:

1. Slide panel into place on unit.

2. Secure the panel with two bolts.

To remove battery panel:

1. Ensure the roof is in the open position.

2. Remove the two bolts (D) that secure the panel to

the unit.

3. Lift up on panel and remove.

To secure battery panel:

1. Place panel in unit.

2. Secure the panel with two bolts.

A

B

C

D

17

The Gaseous Fuel System

The information below is provided to assist

gaseous fuel system technicians in planning

installations. In no way should this information

be interpreted to override applicable fuel gas

codes. Consult with your local fuel supplier or Fire

Marshall if questions or problems arise.

TO THE INSTALLER: Consult with the generator

owner(s) and convey any technical considerations

that might affect their installation plans before

applying these general guidelines.

The following general rules apply to gaseous fuel

system piping:

WARNING Propane and Natural Gas are extremely

flammable and explosive, which could cause

burns, fire or explosion resulting in death,

serious injury and/or property damage.

• Before placing the generator into service, the fuel system

lines must be properly purged and leak tested.

• No leakage is permitted.

NOTICE The supplied flexible

steel fuel line

is not to be

installed underground or in contact with the ground.

• The entire

flexible

steel fuel line must be visible for

periodic inspection and must not be concealed

within nor contact nor run through any wall, floor,

or partition.

• The piping should be of a material that conforms

to federal and local codes, rigidly mounted and

protected against vibration.

• Piping should be protected from physical

damage where it passes through flower beds,

shrub beds, and other cultivated areas where

damage could occur.

NOTICE The illustration is representative of a typical

installation. Your installation may differ.

• Install the

flexible

steel fuel line

(B)

(supplied)

between the generator fuel inlet port

(A)

and

rigid piping to prevent thermal expansion,

contraction, or any standby movement from

causing excessive stress on the piping material.

A

• A union

(C)

or flanged connection shall be

provided downstream to permit removal of standby

generator.

• A manometer port should be provided

(D)

. A digital

manometer, P/N 19495, is available at your Briggs &

Stratton service center. When the initial test runs are

completed, the manometer is removed and the port

is plugged. The manometer port permits temporary

installation of a manometer to ensure that the

engine receives the correct fuel pressure to operate

efficiently throughout its operating range.

• Where the formation of hydrates or ice is known

to occur, piping should be protected against

freezing. The termination of hard piping should

include a sediment trap

(F)

where condensate is

not likely to freeze.

• A minimum of one accessible, approved manual

shutoff valve (E) shall be installed in the fuel supply

line within 6 ft. (180 cm) of the standby generator.

• A manual fuel shut-off valve should be installed

in the interior of the building.

• Where local conditions include earthquake,

tornado, unstable ground, or flood hazards, special

consideration shall be given to increase strength

and flexibility of piping supports and connections

• Piping must be of the correct size to maintain

the required supply pressures and volume flow

under varying generator load conditions with all

gas appliances connected to the fuel system

turned on and operating.

• Use a pipe sealant or joint compound approved

for use with NG/LPG on all threaded fittings to

reduce the possibility of leakage.

• Installed piping must be properly purged and

leak tested, in accordance with applicable codes

and standards.

WARNING Propane and Natural Gas are extremely

flammable and explosive, which could cause

burns, fire or explosion resulting in death,

serious injury and/or property damage.

• LP gas is heavier than air and will settle in low areas.

• Natural gas is lighter than air and will collect in high areas.

• The slightest spark could ignite these fuels and

cause an explosion.

• DO NOT light a cigarette or smoke.

A

B

C

D

E

F

18

Fuel Consumption

Estimated fuel supply requirements at half and full load

for natural gas and LP vapor fuels are shown below.

LP Vapor (Propane)

20kW 17kW

Full Load

Cu Ft/Hr 135 118

Gal/Hr

(liquid)

3.75 3.28

BTU/Hr 337500 295000

3/4 Load

Cu Ft/Hr 109 99

Gal/Hr

(liquid)

3.03 2.75

BTU/Hr 272500 247500

1/2 Load

Cu Ft/Hr 83 74

Gal/Hr

(liquid)

2.31 2.06

BTU/Hr 207500 185000

1/4 Load

Cu Ft/Hr 56 54

Gal/Hr

(liquid)

1.56 1.5

BTU/Hr 140000 135000

Exercise

Cu Ft/Hr 40 40

Gal/Hr

(liquid)

1.11 1.11

BTU/Hr 100000 100000

Natural Gas

20 kW

(18 kW)

17 kW

(15.3 kW)

Full Load

Cu Ft/ Hr 260 248

BTU / Hr 260000 248000

3/4 Load

Cu Ft/ Hr 240 218

BTU / Hr 240000 218000

1/2 Load

Cu Ft/ Hr 187 170

BTU / Hr 187000 170000

1/4 Load

Cu Ft/ Hr 135 128

BTU / Hr 135000 128000

Exercise

Cu Ft/ Hr 99 99

BTU / Hr 99000 99000

Recommended

Energy Content of

Fuel

LP Vapor Natural

Gas

Heating Value:

BTU per gallon (gross**)

Cubic feet (gas)

91,547

2,500 1,000

Fuel Pressure

Both LP vapor and natural gas fuel supply pressure

at the generator’s fuel inlet port should be between

the following levels at full load with all gas appliances

turned on and operating.

• NG is 3.5-7”

• LP is 11-14” W.C.

Ensure that all gas line shutoff valves are OPEN and

that adequate fuel pressure is available whenever

automatic operation is desired.

For natural gas fuel pressure levels of 3.5-5” W.C.,

replace regulator assembly with service kit 6331-00.

Power Loss

Air density is less at high altitudes, resulting in less

available engine power. Specifically, engine power

will decrease 3.5% for each 1,000 feet (300 meters)

above sea level and 1% for each 10° F (5.6°C) above

77°F (25°C). Make sure you and your installer consider

these factors when determining total generator load.

Fuel Pipe Sizing

There are numerous on-line or otherwise-published

references for fuel pip sizing. For example, NFPA

54-Natural Fuel Gas Code, 2006 (Item #: 320-6031-06)

is a common resource.

The installer should consider the specific gravity of gas

and compensate for a nominal amount of restriction

from bends, fittings, etc. If an unusual number of

fittings, bends, or other restrictions are used, refer to

federal and local codes for guidance.

19

Fuel Conversion

The engine of your generator system is factory calibrated

to run on natural gas (NG) or on liquefied petroleum (LP)

vapor. To convert to either fuel, follow these steps:

NOTICE Units are set to NG at the factory.

1. Put the key into the lock of the front panel. Lightly

push down on the roof above the lock, and then

turn the key one quarter turn clockwise.

2. Lift the roof to the open position.

3. Push the control board OFF button.

4. Remove 15-amp fuse from the control panel.

5. Remove the rear panel.

6. Find the fuel selector switch (A) on top of the fuel

regulator (B).

Option A:

• Use a 5 mm hex wrench and turn the selector

switch to LP or NG.

• Install the tamper-proof plug (supplied) over fuel

selector switch. Make sure that the convex side

points out.

Option B:

• Remove cap (C) from Fuel Select Valve by

sliding it upward.

• LP or NG is selected by using the cap (C)

as a tool to rotate the indicator to the LP or

NG mark (the image below shows the FSV

set to LP fuel).

• Install the cap (C) after fuel selection is

complete.

7. Once the fuel selection is complete, apply

a drop of cyanoacrylate (super) glue on

the Fuel Select Cap (C) before installing it

again.

8. Install the rear panel.

9. Install 15-amp fuse in the control panel.

10. Push the control board AUTO button.

11. Close the roof.

A

B

C

Option B:

Option A:

20

System Connectors

Low Voltage connections to signal fault contacts, transfer switch communication and auxiliary 12VDC power are

made via a field connection terminal block in control board area. Compare this illustration with your generator to

familiarize yourself with the location of these connections.

• For power output connection (Line 1, Line 2, Neutral, and Ground), refer to the following table:



17 kW 20 kW

4AWG [21 mm

2

] Cu 4AWG [21 mm

2

] Cu

3AWG [27 mm

2

] Al 2AWG [34 mm

2

] Al

• Reference NEC 2014 table 310.15 (B) (16) • Use National Electric Code for correction factors and wire size calculations

• Metric system rounded for simplicity.

• For transfer switch communication use #18 AWG [1 mm

2

] twisted pair conductors, no greater than 200 ft in length, 300

volt 90°C wire.

• When connecting to the terminal block, fasten only one wire to each connector screw.

• Torque terminal block screws to 4.4 in-lb [0.49 Newton meter].

• Torque circuit breaker connections to 45 in-lb [5 Newton meter].

A

- Two Pin Terminal Block — Used to connect

utility 240 VAC from fuse block in ATS to the

control board. Connect only one wire per

terminal. Use #14 AWG [2.5 mm

2

] minimum 300

volt wire.

B

- Fault Contacts — Use NO, COM and NC to

hook up a siren, light, etc. to alert you in case of

a fault. Contacts reverse state (NO goes to NC

and vice versa) upon a fault condition.

C

– Transfer Switch Communication (TxRx

and TxRx GND) — Connect to transfer switch

control board for communication interface using

18AWG [1 mm

2

] twisted pair wire.

D

– +LED and GND Connection — Not required for

wireless monitor included with unit. Available for

optional hardwired remote system status panel

accessory, #6154.

E

- Eight Pin Terminal Block — Used to connect

signal wires to the control board. Connect only

one wire per terminal.

F

- Power Connection (Line 1 and Line 2) —

Power connection to transfer switch.

G

- Ground Connection — Connect to transfer

switch ground

H

- Neutral Connection — Connect to transfer

switch neutral

25

26

1

2

3

4

5

6

7

8

]

L1

N

L2

B

C

F

H

G

D

A

E

La page charge ...

Simplicity 040547-00 Guide d'installation

Ce manuel convient également à

Simplicity 040547-00 Guide d'installation

dans d''autres langues

Documents connexes