Simplicity 020522-00 Manuel utilisateur

Marque: Simplicity

Modèle: 020522-00

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association

(PWMA) standard PW101-2010 (Testing and Rating Performance of Pressure Washers).

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

MILWAUKEE, WISCONSIN, U.S.A.

Manual No. 315652 Revision A

Electric

Pressure Washer

OPERATOR’S

MANUAL

2 BRIGGSandSTRATTON.COM

Thank you for purchasing this quality-built Briggs & Stratton® electric pressure washer. We are pleased that you’ve placed your

confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your Briggs &

Stratton electric pressure washer will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with electric pressure washers and

how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this electric pressure washer could

be used for, it is important that you read and understand these instructions thoroughly before attempting to start or operate this

equipment. Save these original instructions for future reference.

This electric pressure washer requires final assembly before use. Refer to the Assembly section of this manual for instructions on

final assembly procedures. Follow the instructions completely.

Where to Find Us

Should you require assistance with set-up, or immediate answers regarding the operation of your model, please call us toll free at

(800) 743-4115, Monday through Friday, between 8:00 AM and 5:00 PM CST.

Electric Pressure Washer

Model Number

Revision

Serial Number

Date Purchased

Briggs & Stratton Power Products is a registered

trademark of Briggs & Stratton Corporation

Milwaukee, WI, USA

Table of Contents

Operator Safety .................................4

Equipment Description.........................................4

Important Safety Information....................................4

Assembly .....................................7

Unpack Electric Pressure Washer ................................7

Prior to Operation ............................................7

Assemble Main Unit...........................................8

Lubricate O-Rings ............................................9

Connect Hoses and Water Supply ...............................10

Connect Wand and Spray Tips..................................10

Checklist Before Starting Pump Motor............................11

Servicing Of A Double-Insulated Appliance ........................11

Features and Controls............................ 12

Operation .................................... 13

How to Start Your Electric Pressure Washer .......................13

How to Stop Your Electric Pressure Washer .......................14

How to Use the Spray Tips ....................................14

Applying Detergent...........................................15

Electric Pressure Washer Rinsing ...............................15

How to Use the Electric Inflator Function..........................16

Maintenance .................................. 17

General Recommendations ....................................17

Electric Pressure Washer Maintenance ...........................17

Spray Tip Maintenance........................................18

Pump and Motor Maintenance..................................18

After Each Use ..............................................19

Winter or Long Term Storage ...................... 19

Initial Storage Procedures .....................................19

Protecting the Pump .........................................19

Final Storage Procedures......................................19

Troubleshooting................................ 20

Warranty..................................... 21

Electric Pressure Washer Owner Warranty ........................21

Product Specifications ........................... 22

4 BRIGGSandSTRATTON.COM

Operator Safety

SAVE THESE INSTRUCTIONS

Equipment Description

The electric pressure washer operates at 1700 PSI (117.2 BARS)

at a flow rate of 1.3 gallons per minute (4.9 liters per minute).

Every effort has been made to ensure that the information in

this manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and this

document at any time without prior notice.

Ground Fault Circuit Interrupter Protection

This product must be properly grounded. This pressure washer

is provided with a ground-fault circuit-interrupter (GFCI) built

into the plug of the power supply cord. This device provides

additional protection from the risk of electric shock. Should

replacement of the plug or cord become necessary, use only

identical replacement parts that include GFCI protection.

Automatic Shut-Off

The electric pressure washer is equipped with a sensor that will

detect that water flow has stopped when releasing or locking the

spray gun trigger. The sensor will cause the motor to shut off for

as long as the spray gun trigger is released or locked.

If the motor continues to run when the spray gun trigger is

released or locked, DO NOT USE THE MACHINE. Call the electric

pressure washer helpline at (800) 743-4115 for assistance.

NOTICE The electric pressure washer is equipped with a main

power ON/OFF switch. The switch should always be set to the

OFF position (O) when the electric pressure washer is not being

used to prevent possible damage.

Motor Overload

The electric motor in this electric pressure washer is equipped

with an overload protection device (thermostat). This device will

automatically shut off the motor if the motor overheats or draws

excessive current.

If the overload protection device is tripped, disconnect the power

supply by turning the master ON/OFF switch to the OFF (O)

position. Let unit cool for 30 minutes. Then turn the master ON/

OFF switch to the ON (—) position to resume operation.

Important Safety Information

Please read and understand this entire manual before attempting

to assemble, operate or service the product. Follow the

maintenance instructions specified in this manual. If you have

any questions regarding the product, please call customer service

at (800) 743-4115, 8 a.m. - 5 p.m., CST, Monday - Friday.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal injury

hazard. A signal word (DANGER, WARNING, or CAUTION) is used

with the alert symbol to designate a degree or level of hazard

seriousness. A safety symbol may be used to represent the type

of hazard. The signal word NOTICE is used to address practices

not related to personal injury.

DANGER indicates a hazard which, if not avoided, will result in

death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could result

in minor or moderate injury.

NOTICE address practices not related to personalinjury.

For Grounding Instructions, See Assembly Section.

WARNING Failure to read and follow the operator’s

manual and all operating instructions before using

could result in death, serious injury, and/or property

damage.

• Read this manual carefully and become familiar with your

electric pressure washer. Know its applications, its limitations,

and any hazards involved.

WARNING Risk of electrocution. Use of an extension cord

could cause electric shock or burn resulting in death or

serious injury.

• DO NOT use an extension cord with this electric pressure

washer. Your home’s electrical circuit receptacle or extension

cord may not provide lifesaving ground-fault circuit-

interruption protection.

Chemical Burn

Electrical Shock

Slippery Surface Fall

Flying Objects

Read Manual

Projectile

Fluid Injection

Fire

Bursting

WARNING Risk of electrocution. Contacting both power

conductors, at the same time could cause electric

shock or burn resulting in death or serious injury.

• Connect only to a properly grounded outlet. DO NOT remove

ground pin from plug.

• Inspect cord before each use, DO NOT use if cord is

damaged.

• The product is equipped with a ground fault circuit interrupter

(GFCI) built into the power cord plug. If replacement of the

plug or cord is required, use only identical replacement parts.

• Keep all connections dry and off the ground.

• DO NOT touch plug with wet hands.

• DO NOT run cord through doorways, windows, holes in

ceilings, walls, or floors.

• DO NOT walk on cord.

• DO NOT drive over, drag or place objects over cord.

• DO NOT spray near power source.

WARNING Use of electric pressure washer could create

puddles and slipperysurfaces.

Risk of kickback. Spray gun could kickback

causing you to fall resulting in death or

serious injury.

• Operate the electric pressure washer from a stablesurface.

• Do not overreach or stand on unstable support. Keep good

footing and balance at all times.

• The cleaning area should have adequate slopes and drainage

to reduce the possibility of a fall due to slippery surfaces.

• Be extremely careful if you must use the electric pressure

washer from a ladder, scaffolding, or any other similar

location.

• Firmly grasp spray gun with both hands when using power

spray modes to avoid injury when spray gun kicks back.

WARNING Chemical Burn Hazard.

Chemicals could cause burns resulting in

death or serious injury.

• Always wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using chemicals.

• DO NOT substitute safety glasses or dry-condition goggles

for indirect vented safetygoggles.

• DO NOT use caustic liquid with electric pressure washer.

• Use ONLY pressure washer safe detergents/soaps. Follow all

manufacturers instructions.

WARNING The high pressure stream of water that this

equipment produces could cut through skin and its

underlying tissues, resulting in serious injury and

possible amputation.

Spray gun traps high water pressure, even when motor is

stopped and water is disconnected, which could result in

serious injury.

• NEVER aim spray gun at people, animals, or plants.

• ALWAYS point spray gun in safe direction, squeeze spray

gun trigger to release high pressure, every time you turn off

pressure washer.

WARNING Risk of eye or bodily injury. Spray could splash

back, propel objects or cause internal harm

resulting in serious injury.

• Always wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using or in vicinity

of this equipment. NEVER substitute safety glasses or dry-

condition goggles for indirect vented safety goggles.

• Know how to stop the pressure washer and bleed pressure

quickly. Be thoroughly familiar with the controls.

• DO NOT allow CHILDREN to operate the electric pressure

washer.

• Keep operating area clear of all persons.

• Inspect high pressure hose before each use. NEVER repair

high pressure hose; replace it.

• DO NOT repair leaking connections with sealant of any kind;

replace o-rings and gaskets.

• Keep hose connected to electric pressure washer and spray

gun while system is pressurized.

• ALWAYS point spray gun in safe direction while system is

pressurized and squeeze spray gun trigger to release high

pressure, every time you turn off the pressure washer.

• DO NOT aim spray gun at people or animals.

• DO NOT

drink from hose connected accessories.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while the electric

pressure washer is in ON (—) position.

• DO NOT use a spray gun which does not have a trigger lock

or trigger guard in place and in working order.

• Always be certain spray gun and accessories are correctly

attached.

• Stay alert – watch what you are doing.

• DO NOT operate the product when fatigued or under the

influence of alcohol or drugs.

• Close supervision is necessary when this product is used near

children.

6 BRIGGSandSTRATTON.COM

WARNING Risk of fire. Spraying flammable liquids could

result in death or serious injury.

• DO NOT spray flammable liquids.

WARNING Risk of fire. Overheated cord could result in

death or serious injury.

• Uncoil cord completely prior to use.

• DO NOT cover cord with any material.

WARNING This product contains lead and lead

compounds, known to the State of California to cause birth

defects or other reproductive harm. Wash your hands after

handling this product.

NOTICE High pressure spray could damage fragile items

including glass.

• DO NOT point spray gun at glass when using red (0°) spray

tip.

• NEVER aim spray gun at plants.

NOTICE Improper treatment of electric pressure washer could

damage it and shorten its life.

• If you have questions about intended use, ask dealer or

contact authorized service center.

• DO NOT operate units with broken or missing parts, or

without protective housing or covers.

• DO NOT by-pass any safety device on the electric pressure

washer.

• DO NOT modify the electric pressure washer in any way.

• Before starting the electric pressure washer in cold weather,

check all parts of the equipment to be sure ice has not formed

there.

• DO NOT move the electric pressure washer by pulling on

hoses. Move unit using the transport handle supplied.

• Use ONLY branded accessories intended for use with this

product.

WARNING Risk of bursting. High pressure air could result

in death or serious injury.

• Follow manufacturer’s instructions on items to avoid over

inflation.

• Use only recommended air-handling parts acceptable for

pressures not less than 250 PSI.

• Do not leave inflator unattended while running.

• Do not use at pressure greater than 100 PSI.

• Air pressure gauge for reference only.

• Always check items being inflated with a calibrated gauge to

determine actual pressure.

• Inflating items 10 PSI or less, inflate using short bursts and

check pressure with calibrated gauge.

Assembly

Read entire operator’s manual before you attempt to

assemble or operate your new electric pressure

washer.

Your electric pressure washer requires some assembly but

is quickly ready for use. If you have any problems with the

assembly of your electric pressure washer, please call the

electric pressure washer helpline at (800) 743-4115. If calling for

assistance, please have the model, revision, and serial number

from the identification label available.

Tools Needed

 • Phillipsscrewdriver,#2

 • Needlenosepliers

Items Not Included

 • Gardenhose

Unpack Electric Pressure Washer

1. Remove everything from carton.

2. Ensure you have all included items prior to assembly.

Items Included in the Carton

 • Mainunit

 • Handle

 • Accessorytray

 • Wheels(2)

 • Detergentbottle

 • StabilityFoot

 • Screws(6)

 • Spraygun

 • Highpressurehose

 • Turbowand

 • Metalwand(1)andtips(3)

 • Partsbag(whichincludesthefollowing):

 • O-rings,spare:2forspraygun;2largeand2smallfor

high pressure hose

 • Operator’smanual

 • Owner’sregistrationcard

Check all contents. If any parts are missing or damaged, call the

electric pressure washer helpline at (800) 743-4115.

Become familiar with each component before assembling the

electric pressure washer. Identify contents with the illustration

shown in Features and Controls.

Prior to Operation

1. Please fill out and send in the registration card.

2. Read and perform the following instructions while paying

close attention to all warnings and notices.

NOTICE Connect ONLY to water source capable of supplying a

minimum of 3 gpm (11.4 l) and no less than 20 psi (1.38 bars)

at the electric pressure washer end of garden hose. Inspect all

equipment, hoses and accessories thoroughly before each use;

DO NOT use if damaged.

• ONLY use branded accessories intended for use with this

product.

• For optimum performance, DO NOT use a garden hose that

exceeds 50 feet in length.

• Replace only with original equipment parts.

• To order, call (800) 743-4115 or visit

BRIGGSandSTRATTON.COM.

8 BRIGGSandSTRATTON.COM

Assemble Main Unit

When performing the following assembly procedures, pay close

attention to the illustration at the bottom of this page.

1. Remove and discard the protective cap (A) from each wheel

shaft.

NOTICE During shipment wheel tabs may compress inward. If

so, gently spread tabs outward.

2. Slide wheel shafts (B) into holes at sides of main unit (C).

Wheels are installed correctly when you hear a CLICK and

they are securely in place.

3. Slide the handle (D) into the slots at top of main unit. Install

two (2) screws to secure the handle to the main unit.

4. Slide accessory tray (E) into slots at back of main unit. Install

two (2) screws to secure the accessory tray to the main unit.

5. Install stability foot (F) if equipped, and secure using two

screws.

6. Confirm that black rubber gasket (G) is installed in water inlet

located at lower front of unit.

7. Place detergent bottle (H) onto shelf at back of unit.

8. Rotate detergent bottle cap (J) counter-clockwise until it

clicks onto retaining tab. Make sure that end of suction hose

contacts bottom of bottle.

Lubricate O-Rings

Lubrication of o-rings is extremely important for installation and

operation. The use of a lubricant (petroleum or synthetic grease)

during assembly helps seat o-rings properly and provides an

improved seal. It also helps protect the o-ring from damage by

abrasion, pinching or cutting and extends the life of the o-ring.

NOTICE ALWAYS apply a small amount of lubricant on o-rings

prior to assembling the garden hose to the pump (A), high

pressure hose (pump end) (B), high pressure hose (gun end)

(C), turbo wand (gun end) (D), metal wand (spray tip end) (E)

and metal wand (gun end)(F).

Lubricate all connections shown below, following these

instructions:

1. Inspect and clean connecting surfaces prior to lubrication and

assembly.

2. Use lubricants sparingly during assembly; a light film is all

that is required.

3. Use a small brush or cotton swab to apply grease directly to

o-rings where they are not accessible (QC fitting, M22 fitting).

10 BRIGGSandSTRATTON.COM

Connect Hoses and Water Supply

NOTICE Use ONLY cold water (less than 100°F).

1. Attach garden hose (50 ft. / 15.24 m maximum) to water

supply.

2. Run water through garden hose for 30 seconds to flush the

hose of debris. Turn off water.

3. Confirm that black rubber gasket (A) is installed in water inlet

located at lower front of unit.

NOTICE DO NOT run the pump without the water supply

connected and turned on.

 • Damagetoequipmentresultingfromfailuretofollowthis

instruction will void warranty.

4. Attach opposite end of garden hose (B) to the water inlet

coupling (C). Tighten by hand.

5. Attach high pressure hose (D) to the unit’s water outlet (E)

located at lower back of unit. Tighten by hand.

6. Attach opposite end of high pressure hose to the spray gun.

Press red button (F) on spray gun, then insert end of high

pressure hose (D) into gun until it SNAPS into place. Release

the red button and make sure connection is secure.

Connect Wand and Spray Tips

1. Turn ON water, point gun in a safe direction, press trigger

release (G), then squeeze trigger (H) to purge pump system

and spray gun of air and impurities.

2. Insert and twist wand (J) into spray gun (K). Once wand

slides into gun, apply further inward pressure to wand and

twist 1/4 turn clockwise until securely in place.

3. When the metal wand is installed, select the spray tip you

want to use. Pull back on collar of wand (M), insert spray

tip (N) and release collar. Tug on spray tip to make sure it is

securely in place. See How to Use Spray Tips.

4. Turn OFF water and release trigger. Point gun in a safe

direction and make sure trigger cannot be squeezed.

Checklist Before Starting Pump Motor

Review the unit’s assembly to ensure you have performed all of

the following.

1. Be sure to read Operator Safety and Operation before using

the electric pressure washer.

2. Check for properly tightened hose connections.

3. Check to make sure there are no kinks, cuts, or damage to

hoses.

4. Provide a proper water supply at an adequate flow (not to

exceed 100 °F).

5. Plug electrical cord into a properly grounded electrical source.

Servicing Of A Double-Insulated Appliance

In a double-insulated product, two systems of insulation are

provided instead of grounding. No grounding means is provided

on a double-insulated product, nor should a means for grounding

be added to the product. Servicing a double-insulated product

requires extreme care and knowledge of the system, and should

be done only by qualified service personnel. Replacement parts

for a double-insulated product must be identical to the parts they

replace. A double-insulated product is marked with the words

“DOUBLE INSULATION” or “DOUBLE INSULATED.”

The symbol means DOUBLE-INSULATED APPLIANCE.

12 BRIGGSandSTRATTON.COM

Features and Controls

Read the Operator’s Manual and safety rules before operating your electric pressure washer.

Compare the illustrations with your electric pressure washer to familiarize yourself with the locations of various controls and

adjustments. Save this original manual for future reference.

A - Spray Gun — Controls the application of water onto cleaning

surface with trigger device. Includes trigger lock.

B - Pressure Gauge — Shows the amount of air pressure in the

object being inflated.

C - Master ON/OFF Toggle Switch — Push top of switch in (–)

for pressure washer function ON. Push Bottom of switch in

(=) for inflator function ON. Place switch in center position

(O) for OFF.

D - Electric Cord with GFCI — The electric pressure washer and

operator is protected by a ground fault circuit interrupter

(GFCI).

E - Water Supply Inlet — Connect to water supply using a 50 ft.

(15.24 m) maximum garden hose.

F - Air Hose — Used to inflate small inflatables.

G - Stability Foot — Stabilizes the pressure washer when in the

upright position.

H - Metal Wand with Quick Connect — Allows you to switch

between three different spray tips.

J - Detergent Bottle — Used to siphon pressure washer safe

detergents into a low pressure stream.

K - Accessory Tray — Provides convenient storage for standard

and optional accessories.

M - High Pressure Hose — Connect one end to high pressure

water outlet and the other end to spray gun.

N - Spray Tips — Detergent (black), 0° (red) and 15° (orange)

for various high pressure applications.

P - Spray Tip Cleaner — Used to remove sediment and clogs

from spray tips.

R - Identification Label — Provides model and serial number of

pressure washer. Please have these readily available if calling

for assistance.

S - High Pressure Water Outlet — Connection for high pressure

hose.

T - Turbo Wand — Whirls a powerful pin-point jet of water for

intense cleaning.

Items Not Shown:

Warning Labels — Identifies hazards to be avoided when using

your pressure washer.

Operation

How to Start Your Electric Pressure Washer

Follow the instructions below in the order presented. If you have

any problems operating your electric pressure washer, please call

the electric pressure washer helpline at (800) 743-4115.

WARNING Risk of eye injury. Spray could splash back

or propel objects resulting in serious injury.

Always

wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using or in

vicinity of this equipment. NEVER substitute safety glasses or

dry-condition goggles for indirect vented safety goggles.

1. Place the electric pressure washer near an outside water

source capable of supplying water at a flow rate greater than

3 gallons per minute (11.4 l) and no less than 20 psi (1.38

bars) at the electric pressure washer end of garden hose.

DO NOT siphon supply water.

2. Connect garden hose to water inlet.

3. Check that high pressure hose is tightly connected to spray

gun. See Connect Hoses and Water Supply for illustrations.

NOTICE DO NOT run the pump without the water supply

connected and turned on.

 • Damagetoequipmentresultingfromfailuretofollowthis

instruction will void warranty.

4. Turn ON water, point gun in a safe direction, press trigger

lock button and squeeze trigger to purge pump system of air.

5. Remove any dirt or foreign matter from spray tips. Install

desired wand and spray tips onto spray gun. See Connect

Hoses and Water Supply and How to Use the Spray Tips for

details.

6. Press the master ON/OFF switch (A) to the OFF (O) center

position.

WARNING Risk of electrocution. Use of an extension cord

could cause electric shock or burn resulting in death or

serious injury.

• DO NOT use an extension cord with this electric pressure

washer. Your home’s electrical circuit receptacle or extension

cord may not provide lifesaving ground-fault circuit-

interruption protection.

7. Plug electrical power cord into an electrical circuit rated

for 120 Volts AC at 15 Amps that is properly installed and

grounded in accordance with all local codes and ordinances.

The indicator light on the GFCI should be ON.

WARNING Risk of electrocution. Non-operating ground

fault circuit interrupter (GFCI) could result in death or

serious injury. If indicator light does not stay ON after

test and reset, do not use GFCI.

NOTICE The indicator light must be ON for the electric pressure

washer to operate.

8. Press TEST button (B). The indicator light (D) should be OFF.

9. Press RESET button (C). The indicator light (D) should be ON.

NOTICE DO NOT use the electric pressure washer if above test

fails.

10. Press the master ON/OFF switch (A) to the Pressure Washer

ON (—) position.

WARNING Risk of kickback.

Spray gun could kickback causing you to fall resulting

in death or serious injury.

• Operate the electric pressure washer from a stablesurface.

• Be extremely careful if you must use the electric pressure

washer from a ladder, scaffolding, or any other similar

location.

• Firmly grasp spray gun with both hands when using power

spray modes to avoid injury when spray gun kicks back.

11. Point gun in a safe direction, press trigger lock button and

squeeze trigger. The electric pressure washer motor will start

and stop as spray gun trigger is depressed and released.

The electric pressure washer is now ready for use. Instructions

for use of the supplied accessories are given later in this section.

14 BRIGGSandSTRATTON.COM

How to Stop Your Electric Pressure Washer

The electric pressure washer motor runs only when the trigger is

engaged. To stop the electric pressure washer and turn off the

motor:

1. Release spray gun trigger.

2. Press the master ON/OFF switch to the OFF (O) position.

NOTICE Releasing the trigger will shut off the motor but does

not shut off electrical power to the unit.

3. Turn off water supply.

4. ALWAYS point spray gun in a safe direction and squeeze

spray gun trigger to relieve built up pressure in the unit.

WARNING The high pressure stream of water that this

equipment produces could cut through skin and its

underlying tissues, resulting in serious injury and

possible amputation.

Spray gun traps high water pressure, even when motor is

stopped and water is disconnected, which could result in

serious injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, squeeze spray

gun trigger to release high pressure, every time you turn off

pressure washer.

5. Disconnect GFCI plug from outlet and coil power cord.

6. Flush detergent bottle (if used) by removing it from the

pressure washer and pouring out all remaining solution.

7. Rinse detergent bottle out with fresh clean water and reinstall

onto pressure washer.

8. Coil and store power cord, high pressure hose and

accessories on the accessory tray. Store spray gun in clip on

side of unit.

How to Use the Spray Tips

You should now be familiar with how to START and STOP your

electric pressure washer. If not, please refer to the previous

section to familiarize yourself with STARTING and STOPPING the

system before continuing.

The quick–connect on the metal wand allows you to switch

between three different quick connect spray tips. Spray tips can

be changed while pressure washer is running once spray gun

trigger lock is engaged. The spray tips vary the spray pattern as

shown.

Follow these instructions to change spray tips:

1. Pull back collar on quick–connect and pull current spray tip

off. Store spray tips in holder provided on the metal wand.

WARNING The high pressure stream of water that this

equipment produces could cut through skin and its

underlying tissues, resulting in serious injury and

possible amputation.

• NEVER exchange spray tips without the trigger lock being

engaged on the spray gun.

• DO NOT twist spray tips while spraying.

2. Select desired spray tip:

  • Forgeneralrinse,selectorange15°spraytip.

  • Toscoursurface,selectred0°spraytip.

  • Toapplydetergent,selectblackspraytip.

Low Pressure

High Pressure

Black

Use to apply detergent

15° Orange

1300 PSI

1.3 GPM

0° Red

1700 PSI

1.0 GPM

3. Pull back on collar, insert new spray tip and release collar.

Tug on spray tip to make sure it is securely in place.

Usage Tips

 • Formosteffectivecleaning,keepspraytipfrom8to24

inches away from cleaning surface.

 • Ifyougetspraytiptooclose,especiallyusingahigh

pressure spray tip, you may damage surface being cleaned.

 • DoNotgetcloserthan6incheswhencleaningtires.

Applying Detergent

WARNING Chemical Burn Hazard.

Chemicals could cause burns resulting in

death or serious injury.

• Always wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using chemicals.

• DO NOT substitute safety glasses or dry-condition goggles

for indirect vented safetygoggles.

• DO NOT use caustic liquid with electric pressure washer.

• Use ONLY pressure washer safe detergents/soaps. Follow all

manufacturers instructions.

To apply detergent, follow these steps:

1. Review use of spray tips shown in How to Use the Spray Tips.

2. Prepare your detergent solution as required by job to be

performed.

3. Rotate detergent bottle cap (A) clockwise to release from

retaining tab. Remove cap from detergent bottle (B).

A CB

4. Fill bottle with detergent solution (B).

5. Place suction hose and cap back into detergent bottle.

6. Rotate detergent bottle cap (C) counter-clockwise until it

clicks onto retaining tab. Make sure that end of suction hose

contacts bottom of bottle.

7. Make sure that black detergent spray tip is installed.

NOTICE Detergent cannot be applied with the high pressure

spray tips (Orange or Red).

8. Make sure garden hose is connected to water inlet. Check

that high pressure hose is connected to spray gun and pump.

Turn on water.

NOTICE You must attach all hoses before you start the pressure

washer.

9. Start the pressure washer as instructed in How to Start Your

Electric Pressure Washer.

10. Apply detergent to a dry surface, starting at lower portion

of area to be washed and work upward using long, even,

overlapping strokes.

11. Allow detergent to “soak in” for 3-5 minutes before washing

and rinsing. Reapply as needed to prevent surface from

drying. To prevent streaking, Do Not allow detergent to dry on

surface.

Electric Pressure Washer Rinsing

1. Remove black detergent spray tip from metal wand.

2. Select and install desired high pressure spray tip following

instructions How to Use Spray Tips.

3. Keep spray gun a safe distance from area you plan to spray.

WARNING Risk of kickback.

Spray gun could kickback causing you to fall resulting

in death or serious injury.

• Operate the electric pressure washer from a stablesurface.

• Be extremely careful if you must use the electric pressure

washer from a ladder, scaffolding, or any other similar

location.

• Firmly grasp spray gun with both hands when using power

spray modes to avoid injury when spray gun kicks back.

4. Apply a high pressure spray to a small area and then check

surface for damage. If no damage is found, you can assume it

is okay to continue rinsing.

5. Start at top of area to be rinsed, working down with same

overlapping strokes as you used for cleaning.

Other Cleaning Tips

 • NEVERleavetheelectricpressurewasherunattendedwhile

it is plugged into an electrical outlet and while water is

supplied to the equipment.

 • Ifyouhavethespraytiptoofarawayfromthesurfacebeing

washed, the cleaning may not be as effective.

16 BRIGGSandSTRATTON.COM

How to Use the Electric Inflator Function

Grounding Instructions

This product must be grounded. If it should malfunction or

breakdown, grounding provides a path of least resistance

for electric current to reduce the risk of electric shock. This

product is equipped with a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged into

an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

DANGER! – Improper connection of the equipment-grounding

conductor can result in a risk of electrocution. Check with a

qualiﬁed electrician or service personnel if you are in doubt as

to whether the outlet is properly grounded. Do not modify the

plug provided with the product – if it will not ﬁt the outlet, have

a proper outlet installed by a qualiﬁed electrician. Do not use any

type of adaptor with this product.

WARNING Failure to read and follow the operator’s

manual and all operating instructions before using

could result in death, serious injury, and/or property

damage.

WARNING Risk of electrocution. Contacting both power

conductors, at the same time could cause electric

shock or burn resulting in death or serious injury.

• Connect only to properly grounded outlet. DO NOT remove

ground pin.

• Inspect cord before using – DO NOT use if cord is damaged.

• Keep all connections dry and off the ground.

• DO NOT touch plug with wet hands.

• This product is equipped with a ground fault circuit interrupter

(GFCI) built into the power cord plug. If replacement of the

plug or cord is needed, use only identical replacement parts.

WARNING Risk of bursting. High pressure air could result

in death or serious injury.

• Follow manufacturer’s instructions on items to avoid over

inflation.

• Use only recommended air-handling parts acceptable for

pressures not less than 250 PSI.

• Do not leave inflator unattended while running.

• Do not use at pressure greater than 100 PSI.

• Air pressure gauge for reference only.

• Always check items being inflated with a calibrated gauge to

determine actual pressure.

• Inflating items 10 PSI or less, inflate using short bursts and

check pressure with calibrated gauge.

WARNING Risk of eye injury. High pressure air could

result in serious injury.

• Always wear safety glasses marked to comply with ANSI

Z87.1 when using or in vicinity of this equipment.

WARNING Risk of fire. Using inflator for continuous use

could result in serious injury.

• Allow inflator to cool 3 minutes for each 5 minutes of

continuous use.

The electric inflator operates independent of the pressure

washer; only the electrical power cord needs to be plugged-in as

instructed in this section.

NOTICE Pump damage could result if inflator is used

continuously for over 5 minutes. Let pump cool for 3 minutes

before using again.

NOTICE DO NOT press the master ON/OFF switch (A) to the

ON (—) position (pressure washer function) without the water

supply connected and turned on.

 • Damagetoequipmentresultingfromfailuretofollowthis

instruction will void warranty.

Follow these instructions to operate the electric inflator:

1. Press the master ON/OFF switch (A) to the OFF (O) center

position.

2. Plug electrical power cord into an electrical circuit rated

for 120 Volts AC at 15 Amps that is properly installed and

grounded in accordance with all local codes and ordinances.

The indicator light on the GFCI should be ON.

NOTICE The indicator light must be ON for the electric inflator

to operate.

3. Press TEST button (B). The indicator light (D) should be OFF.

4. Press RESET button (C). The indicator light (D) should be ON.

NOTICE DO NOT use the electric inflator if above test fails.

5. The electric inflator comes equipped with three adapters.

When an adapter is required to inflate an object, lift lever (E)

and insert the appropriate adapter (F) into the inflator hose

end (G). Move lever down to secure the adapter.

G FE

6. Press the master ON/OFF switch (A) to the Inflator ON (=)

position.

7. Insert adapter into the object to be inflated. When inflated,

remove adapter and press the master ON/OFF switch (A) to

the OFF (O) center position.

8. When inflating tires, connect the inflator hose end directly to

the tire stem. When inflated, remove inflator hose end and

press the master ON/OFF switch (A) to the OFF (O) center

position.

9. Disconnect GFCI plug from outlet and coil power cord.

Maintenance

General Recommendations

Regular maintenance will improve the performance and extend

the life of the electric pressure washer.

The electric pressure washer’s warranty does not cover items that

have been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain the

electric pressure washer as instructed in this manual, including

proper storage.

NOTICE Should you have questions about replacing components

on your electric pressure washer, please call (800) 743-4115 for

assistance.

Before Each Use

1. Clean debris.

2. Check water inlet screen for debris or damage.

3. Check high pressure hose for leaks.

4. Check detergent siphoning tube for damage.

5. Check spray gun operation.

Electric Pressure Washer Maintenance

Clean Debris

Daily or before use, clean accumulated debris from electric

pressure washer. Inspect cooling air slots and openings on the

front, rear and bottom of the electric pressure washer. These

openings must be kept clean and unobstructed.

The electric pressure washer parts should be kept clean to reduce

the risk of overheating and ignition of accumulated debris.

 • Useadampclothtowipeexteriorsurfacesclean.

NOTICE Improper treatment of the electric pressure washer can

damage it and/or shorten its life.

 • DONOTinsertanyobjectsthroughcoolingslots.

Check and Clean Water Inlet Screen

Remove water inlet coupling (A). Then remove water inlet screen

(B) from the unit’s water inlet (C) using a needle nose pliers.

Water inlet is located at bottom front of unit. Examine water inlet

screen. If the screen is dirty, clean with a small brush and water.

If the screen is damaged, replace it.

NOTICE If inlet screen is damaged or missing, DO NOT use

electric pressure washer. Call (800) 743-4115 for assistance.

18 BRIGGSandSTRATTON.COM

Check High Pressure Hose

The high pressure hose can develop leaks from wear, kinking,

or abuse. Inspect the hose each time before using it. Check for

cuts, leaks, abrasions or bulging of cover, damage or movement

of couplings. If any of these conditions exist, replace the hose

immediately.

WARNING The high pressure stream of water that this

equipment produces could cut through skin and its

underlying tissues, resulting in serious injury and

possible amputation.

• NEVER repair high pressure hose; replace it.

• Replacement hose rating MUST equal or exceed maximum

pressure rating of unit.

Check Detergent Siphoning Tube

Make sure tube connection is tight. Examine the tube for leaks or

tears and replace if damaged.

Check Spray Gun

Examine the hose connection to the spray gun and make sure it

is secure. Test the trigger (D) by pressing the trigger lock button

(E) and making sure the trigger “springs back” into place when

you release it. You should not be able to press the trigger without

pressing the trigger lock button. Replace spray gun immediately

if it fails any of these tests.

Spray Tip Maintenance

Excessive pump pressure can cause a pulsing sensation felt while

squeezing the spray gun trigger. The principal cause of excessive

pump pressure is a spray tip clogged or restricted with foreign

materials such as dirt, etc. A clogged spray tip could lead to

pump cycling ON/OFF or not turning on even when there is some

flow.

To correct the problem, immediately clean the spray tip by

following these instructions:

1. Press the master ON/OFF switch to the OFF (O) position.

Remove power cord plug from electrical outlet.

2. Disconnect water supply at the electric pressure washer.

3. ALWAYS point spray gun in a safe direction, press trigger

lock button and squeeze spray gun trigger to release retained

high water pressure.

WARNING The high pressure stream of water that this

equipment produces could cut through skin and its

underlying tissues, resulting in serious injury and

possible amputation.

Spray gun traps high water pressure, even when motor is

stopped and water is disconnected, which could result in

serious injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, squeeze spray

gun trigger to release high pressure, every time you turn off

pressure washer.

4. Remove spray tip from end of metal wand (A).

5. Use the wire tip cleaner to free any foreign material clogging

or restricting spray tip (B). The wire tip cleaner is stored at

the lower back left of the unit.

6. Using a garden hose, remove additional debris by back

flushing water through metal wand. Back flush between 30 to

60 seconds.

7. Reinstall spray tip into metal wand.

8. Reconnect metal wand to spray gun.

9. Make sure garden hose is connected to water inlet. Check

that high pressure hose is connected to spray gun and pump.

Turn on water.

10. Plug power cord into electrical outlet and press the master

ON/OFF switch to the Pressure Washer ON ( — ) position.

11. Test the electric pressure washer by operating with each quick

connect spray tip.

Pump and Motor Maintenance

The electric pressure washer does not require any maintenance

to the pump or motor. Both assemblies are pre-lubricated and

sealed, requiring no additional lubrication ever.

After Each Use

Water should not remain in the unit for long periods of time.

Sediments or minerals can deposit on pump parts and “freeze”

pump action. Follow these procedures after every use:

1. Turn off water supply, point gun in a safe direction, press

trigger lock button and squeeze trigger to relieve trapped

pressure.

2. Disconnect garden hose from the water supply and the

electric pressure washer.

3. Disconnect hose from spray gun and high pressure outlet on

pump. Drain water from hose, gun, and wand. Use a rag to

wipe off the hose.

4. Drain water from pump by tipping unit on its front side (water

inlet facing down).

5. Coil and store power cord, high pressure hose and

accessories on the accessory tray. Store spray gun in clip on

side of unit.

6. Store unit in a clean, dry area.

7. If storing for more than 30 days see Winter or Long Term

Storage on next page.

Winter or Long Term Storage

Water should not remain in the unit for long periods of time.

Sediments or minerals can deposit on pump parts and “freeze”

pump action.

Initial Storage Procedures

1. Flush detergent bottle by removing it from unit and pouring

out all remaining solution.

2. Rinse detergent bottle out with fresh clean water.

3. Run the electric pressure washer with the (red) high pressure

spray tip. Flush for one or two minutes.

4. Press the master ON/OFF switch to the OFF (O) position.

Remove power cord plug from electrical outlet.

5. Turn off water supply. Point gun in a safe direction, press

trigger lock button and squeeze trigger to relieve trapped

pressure. After a few moments, release trigger on spray gun.

6. Disconnect garden hose from the water supply and the

electric pressure washer. Disconnect pressure hose from the

pump and the spray gun.

7. Drain water from hoses and spray gun, then use a cloth or

equivalent to wipe off all exterior surfaces.

8. Ensure that inlet and outlet hoses are disconnected from the

pump. Then drain water from pump by tipping unit on its

front side (water inlet facing down).

NOTICE Water left in the pump could freeze and damage the

pump.

Protecting the Pump

To protect the pump from damage caused by mineral deposits

or freezing, use PumpSaver, Model 6039, to treat pump. This

prevents freeze damage and lubricates plunger and seals.

NOTICE PumpSaver is available as an optional accessory. It

is not included with the electric pressure washer. Contact the

nearest authorized service center to purchase Pump Saver.

NOTICE You must protect your unit from freezing temperatures.

 • Failuretodosowillpermanentlydamageyourpumpand

render your unit inoperable.

 • Freezedamageisnotcoveredunderwarranty.

To use PumpSaver, make sure the electric pressure washer is

turned off and inlet and outlet hoses are disconnected. Read and

follow all instructions and warnings given on the PumpSaver

container.

Final Storage Procedures

1. Coil and store power cord, high pressure hose and

accessories on the accessory tray. Store spray gun in clip on

side of unit.

2. Reinstall detergent bottle onto unit.

3. Store unit in a clean, dry area that is protected from freezing

temperatures.

4. Cover unit with a suitable protective cover that does not retain

moisture.

20 BRIGGSandSTRATTON.COM

Troubleshooting

Problem Cause Correction

Pump has following problems:

failure to produce pressure, erratic

pressure, chattering, loss of

pressure, low water volume.

1. Water inlet is blocked.

2. Inadequate water supply.

3. Garden hose is kinked or leaking.

4. Clogged water inlet screen.

5. Water supply is over 100°F (38°C).

6. High pressure hose is blocked or leaks.

7. Spray tip is obstructed.

8. Pump is faulty.

1. Clear inlet.

2. Provide adequate water flow.

3. Straighten garden hose or replace if leaking.

4. Check and clean water inlet screen.

5. Provide cooler water supply.

6. Clear blocks in high pressure hose or

replace hose.

7. Clean spray tip.

8. Contact Briggs & Stratton customer service.

Unit fails to start when spray gun

trigger is squeezed.

1. Water supply is not turned on.

2. Unit is not plugged in.

3. Unit is not turned on.

4. Garden hose is too long.

1. Turn on water supply.

2. Plug electrical power cord into an electrical

circuit rated for 120 Volts AC at 15 Amps

that is properly installed and grounded

in accordance with all local codes and

ordinances.

3. Press the master ON/OFF switch to the

Pressure Washer ON ( — ) position. Reset

GFCI.

4. Use only 50 ft. (15.24 m) maximum garden

hose.

Detergent fails to mix with spray.

1. Siphon tube is clogged or cracked.

2. Siphon tube is not fully inserted in

detergent bottle.

3. High pressure spray tip installed.

1. Clean or replace siphon tube.

2. Insert siphon tube so that end contacts

bottom of detergent bottle.

3. Replace with low pressure (black) spray tip.

Compressor motor fails to start.

1. Unit is not plugged in.

2. Unit is not turned on.

3. Compressor motor is faulty.

1. Plug electrical power cord into an electrical

circuit rated for 120 Volts AC at 15 Amps

that is properly installed and grounded

in accordance with all local codes and

ordinances.

2. Press the master ON/OFF switch to the

Inflator ON ( = ) position. Reset GFCI.

3. Contact Briggs & Stratton customer service.

La page charge ...

Simplicity 020522-00 Manuel utilisateur

Marque: Simplicity

Modèle: 020522-00

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 020522-00 User manual
español: Simplicity 020522-00 Manual de usuario

Simplicity 020522-00 Manuel utilisateur

Simplicity 020522-00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents