LG 65LF6350 Le manuel du propriétaire

Marque: LG

Modèle: 65LF6350

Catégorie: Téléviseurs LCD

Taper: Le manuel du propriétaire

OWNER’S MANUAL

Safety and Reference

P/No : MFL68680203 (1603-REV06)

www.lg.com

*MFL68680203*

Please read this manual carefully before operating your set and

retain it for future reference.

40LF6300

43LF6300

49LF6300

55LF6300

60LF6300

65LF6300

42LF6500

50LF6500

55LF6500

60LF6390

65LF6390

65LF6350

LED TV*

* LG LED TVs are LCD TVs with LED backlighting.

32LF595B

43LF5900

49LF5900

55LF5950

43LH5800

ENGLISH

Important Safety Instructions

Always comply with the following precautions

to avoid dangerous situations and ensure peak

performance of your product.

WARNING/CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead

symbol within an equilateral triangle is

intended to alert the user to the presence of

uninsulated dangerous voltage within the

product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock

to persons.

The exclamation point within an

equilateral triangle is intended to alert the

user to the presence of important operating

and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING/CAUTION

- TO REDUCE THE RISK OF FIRE AND ELECTRIC

SHOCK, DO NOT EXPOSE THIS PRODUCT TO

RAIN OR MOISTURE.

WARNING

If you ignore the warning message, you may

be seriously injured or there is a possibility of

accident or death.

CAUTION

If you ignore the caution message, you may

be slightly injured or the product may be

damaged.

NOTE

The note helps you understand and use the

product safely. Please read the note carefully

before using the product.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

 Do not use this apparatus near water.

 Clean only with dry cloth.

 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety.

If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete

outlet.

 Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

 Only use attachments/accessories specified by the

manufacturer.

 Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid

injury from tip-over.

ENGLISH

 Unplug this apparatus during lightning storms or

when unused for long periods of time.

 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

 Do not press strongly upon the panel with a hand or

a sharp object such as a nail, pencil, or pen, or make a

scratch on it.

 Do not stick metal objects or any other conductive

material into the power cord. Do not touch the end of

the power cord while it is plugged in.

 Keep the packing anti-moisture material or vinyl

packing out of the reach of children. Anti-moisture

material is harmful if swallowed. If swallowed, induce

vomiting and go to the nearest hospital. Additionally,

vinyl packing can cause suffocation. Keep it out of the

reach of children.

 CAUTION concerning the Power Cord

(Can differ by country):

Check the specification page of this owner’s manual

to be certain. Do not connect too many appliances

to the same AC power outlet as this could result in

fire or electric shock. Do not overload wall outlets.

Overloaded wall outlets, loose or damaged wall

outlets, extension cords, frayed power cords, or

damaged or cracked wire insulation are dangerous.

Any of these conditions could result in electric

shock or fire. Periodically examine the cord of your

appliance, and if its appearance indicates damage

or deterioration, unplug it, discontinue use of the

appliance, and have the cord replaced with an exact

replacement part by an authorized service. Protect

the power cord from physical or mechanical abuse,

such as being twisted, kinked, pinched, closed in

a door, or walked upon. Pay particular attention to

plugs, wall outlets, and the point where the cord

exits the appliance. Do not move the TV with the

power cord plugged in. Do not use a damaged or

loose power cord. Be sure do grasp the plug when

unplugging the power cord. Do not pull on the power

cord to unplug the TV.

 Warning - To reduce the risk of fire or electrical shock,

do not expose this product to rain, moisture or other

liquids. Do not touch the TV with wet hands. Do not

install this product near flammable objects such as

gasoline or candles, or expose the TV to direct air

conditioning.

 Do not expose to dripping or splashing and do not

place objects filled with liquids, such as vases, cups,

etc. on or over the apparatus (e.g., on shelves above

the unit).

 Grounding

(Except for devices which are not grounded.)

Ensure that you connect the earth ground wire

to prevent possible electric shock (i.e., a TV with a

three-prong grounded AC plug must be connected

to a three-prong grounded AC outlet). If grounding

methods are not possible, have a qualified electrician

install a separate circuit breaker. Do not try to

ground the unit by connecting it to telephone wires,

lightning rods, or gas pipes.

Circuit

Breaker

Power

Supply

 As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if the unit is turned off.

 Do not attempt to modify this product in any way

without written authorization from LG Electronics.

Unauthorized modification could void the user’s

authority to operate this product.

ENGLISH

 Outdoor Antenna Grounding

(Can differ by country):

If an outdoor antenna is installed, follow the

precautions below. An outdoor antenna system

should not be located in the vicinity of overhead

power lines or other electric light or power circuits, or

where it can come in contact with such power lines

or circuits as death or serious injury can occur. Be sure

the antenna system is grounded to provide some

protection against voltage surges and built-up static

charges. Section 810 of the National Electrical Code

(NEC) in the U.S.A. provides information with respect

to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors, location

of antenna discharge unit, connection to grounding

electrodes, and requirements for the grounding

electrode.

Antenna grounding according to the National

Electrical Code, ANSI/NFPA 70

Ground Clamp

Grounding Conductor

(NEC Section 810-21)

Antenna Lead in Wire

Electric Service

Equipment

Antenna Discharge Unit

(NEC Section 810-20)

Ground Clamp

Power Service Grounding

Electrode System

(NEC Art 250, Part H)

NEC: National Electrical Code

 Cleaning

When cleaning, unplug the power cord and wipe

gently with a soft cloth to prevent scratching. Do

not spray water or other liquids directly on the TV as

electric shock may occur. Do not clean with chemicals

such as alcohol, thinners, or benzine.

 Moving

Make sure the product is turned off, unplugged, and

all cables have been removed. It may take 2 or more

people to carry larger TVs. Do not press or put stress

on the front panel of the TV.

 Ventilation

Install your TV where there is proper ventilation. Do

not install in a confined space such as a bookcase. Do

not cover the product with cloth or other materials

while plugged in. Do not install in excessively dusty

places.

 If you smell smoke or other odors coming from the

TV, unplug the power cord and contact an authorized

service center.

 Keep the product away from direct sunlight.

 Never touch this apparatus or antenna during a

lightning storm.

 When mounting a TV on the wall, make sure not to

install the TV by hanging the power and signal cables

on the back of the TV.

 Do not allow an impact shock or any objects to fall

into the product, and do not drop anything onto the

screen.

 DISCONNECTING THE DEVICE FROM THE MAIN

POWER

The power plug is the disconnecting device. In case

of an emergency, the power plug must remain readily

accessible.

 Batteries

Store the accessories (battery, etc.) in a safe location

out of the reach of children.

 This apparatus uses batteries. In your community

there might be regulations that require you to dispose

of these batteries properly due to environmental

considerations. Please contact your local authorities

for disposal or recycling information.

 Do not dispose of batteries in a fire.

 Do not short circuit, disassemble, or allow the

batteries to overheat.

 Do not use high voltage electrical equipment near

the TV, (e.g., a bug zapper). This may result in product

malfunction.

 Dot Defect

This panel is an advanced product that contains

millions of pixels. In a very few cases, you could see

fine dots on the screen while you’re viewing the TV.

Those dots are deactivated pixels and do not affect

the performance and reliability of the TV.

 Generated Sound

Cracking noise A cracking noise that occurs when

watching or turning off the TV is generated by

plastic thermal contraction due to temperature and

humidity. This noise is common for products where

thermal deformation is required.

Electrical circuit humming/panel buzzing

A low level noise is generated from a high-speed

switching circuit, which supplies a large amount of

current to operate a product. It varies depending

upon the product. This generated sound does not

affect the performance and reliability of the product.

 Take care not to touch the ventilation openings. When

watching the TV for a long period, the ventilation

openings may become hot. This does not affect the

performance of the product or cause defects in the

product.

 Do not install this product on a wall if it could be

exposed to oil or oil mist. This may damage the

product and cause it to fall.

 If the TV feels cold to the touch, there may be a small

flicker when it is turned on. This is normal; there is

nothing wrong with TV. Some minute dot defects

may be visible on the screen, appearing as tiny red,

green, or blue spots. However, they have no adverse

effect on the TV’s performance. Avoid touching the

LCD screen or holding your finger(s) against it for

long periods of time. Doing so may produce some

temporary distortion effects on the screen.

 Displaying a still image for a prolonged period of time

may cause an image sticking. Avoid displaying a fixed

image on the TV screen for a extended length of time.

ENGLISH

FCC Notice

(For USA)

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to radio

or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment

and the receiver.

- Connect the equipment to an outlet on a circuit

different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV

technician for help.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference

and (2) this device must accept any interference

received, including interference that may cause

undesired operation of the device.

Any changes or modifications in construction of

this device which are not expressly approved by

the party responsible for compliance could void the

user’s authority to operate the equipment.

FCC Radio Frequency Interference

Requirements (for UNII devices)

High power radars are allocated as primary users

of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands.

These radar stations can cause interference with

and/or damage this device. This device cannot be

co-located with any other transmitter.

FCC RF Radiation Exposure Statement

[For having wireless function (WLAN, Bluetooth,...)]

This equipment complies with FCC radiation

exposure limits set forth for an uncontrolled

environment. This transmitter must not be co-

located or operating in conjunction with any other

antenna or transmitter.

This equipment should be installed and operated

with minimum distance 20 cm (7.8 inches) between

the antenna and your body. Users must follow the

specific operating instructions for satisfying RF

exposure compliance.

Industry Canada Statement

(For Canada)

[For having wireless function (WLAN, Bluetooth,...)]

This device complies with RSS-210 of the Industry

Canada Rules. Operation is subject to the following

two conditions:

1. this device may not cause interference and

2. this device must accept any interference,

including interference that may cause undesired

operation of the device.

IC Radiation Exposure Statement

(For Canada)

[For having wireless function (WLAN, Bluetooth,...)]

This equipment complies with IC radiation exposure

limits set forth for an uncontrolled environment.

This equipment should be installed and operated

with minimum distance 20 cm (7.8 inches) between

the antenna and your body.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE

FOR ANY RADIO OR TV INTERFERENCE CAUSED

BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT. SUCH MODIFICATIONS COULD

VOID THE USER’S AUTHORITY TO OPERATE THE

EQUIPMENT.

ENGLISH



If you have strabismus (cross-eyed), amblyopia

(weak eyesight) or astigmatism, you may have

trouble sensing depth and easily feel fatigue due

to double images. It is advised to take frequent

breaks than the average adult.



If your eyesight varies between your right and left

eye, correct your eyesight prior to watching 3D

contents.

Symptoms which require discontinuation or

refraining from watching 3D contents



Do not watch 3D contents when you feel fatigue

from lack of sleep, overwork or drinking.



When these symptoms are experienced, stop

using/watching 3D contents and get enough rest

until the symptom subsides.

- Consult your doctor when the symptoms persist.

Symptoms may include headache, eyeball

pain, dizziness, nausea, palpitation, blurriness,

discomfort, double image, visual inconvenience

or fatigue.

CAUTION

Viewing Environment



Viewing Distance

- Maintain a distance of at least twice the screen

diagonal length when watching 3D contents.

If you feel discomfort in viewing 3D contents,

move further away from the TV.

Viewing Age



Infants / Children

- Usage/ Viewing 3D contents for children under

the age of 5 are prohibited.

- Children under the age of 10 may overreact and

become overly excited because their vision is

in development (for example: trying to touch

the screen or trying to jump into it.) Special

monitoring and extra attention is required for

children watching 3D contents.

- Children have greater binocular disparity of 3D

presentations than adults because the distance

between the eyes is shorter than one of adults.

Therefore they will perceive more stereoscopic

depth compared to adults for the same 3D

image.



Teenagers

- Teenagers under the age of 19 may be

stimulated by light coming from 3D videos.

Advise them not to watch 3D videos for a long

time when they are tired.



Elderly

- The elderly may perceive less of a 3D effect than

the youth. Do not sit closer to the TV than the

recommended distance.

WARNING

(For Canada)

[For product having the wireless function using

5 GHz frequency bands]

 The device for operation in the band 5150–5250

MHz is only for indoor use to reduce the potential for

harmful interference to co-channel mobile satellite

systems;

 The maximum antenna gain permitted for devices in

the bands 5250–5350 MHz and 5470–5725 MHz shall

comply with the EIRP limit; and

 The maximum antenna gain permitted for devices in

the band 5725–5825 MHz shall comply with the EIRP

limits specified for point-to-point and non point-to-

point operation as appropriate.

 High-power radars are allocated as primary users

(i.e., priority users) of the bands 5250–5350 MHz

and 5650–5850 MHz and that these radars could

cause interference and/or damage to LE-LAN

devices.

Note to Cable/TV Installer

(For USA and Canada)

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the National

Electric Code (U.S.A.). The code provides guidelines

for proper grounding and, in particular, specifies

that the cable ground shall be connected to the

grounding system of the building, as close to the

point of the cable entry as practical.

Viewing 3D Imaging

(For 3D models)

WARNING

Viewing Environment



Viewing Time

- When watching 3D contents, take five- to

fifteen-minute breaks every hour. Viewing 3D

contents for a long period of time may cause

headache, dizziness, fatigue or eye strain.

Those that have a photosensitive seizure or

chronic illness



Some users may experience a seizure or other

abnormal symptoms when they are exposed

to a flashing light or particular pattern from 3D

contents.



Do not watch 3D videos if you feel nausea, are

pregnant and/ or have a chronic illness such

as epilepsy, cardiac disorder, or blood pressure

disease, etc.



3D Contents are not recommended to those who

suffer from stereo blindness or stereo anomaly.

Double images or discomfort in viewing may be

experienced.

ENGLISH

Cautions when using the 3D glasses



Make sure to use LG 3D glasses. Otherwise, you

may not be able to view 3D videos properly.



Do not use 3D glasses instead of your normal

glasses, sunglasses or protective goggles.



Using modified 3D glasses may cause eye strain or

image distortion.



Do not keep your 3D glasses in extremely high or

low temperatures. It will cause deformation.



The 3D glasses are fragile and are easily scratched.

Always use a soft, clean piece of cloth when

wiping the lenses. Do not scratch the lenses of the

3D glasses with sharp objects or clean/wipe them

with chemicals.

Preparing

NOTE



When the TV is turned on for the first time after

being shipped from the factory, initialization of

the TV may take approximately one minute.



Image shown may differ from your TV.



Your TV’s OSD (On Screen Display) may differ

slightly from that shown in this manual.



The available menus and options may differ from

the input source or product model that you are

using.



New features may be added to this TV in the

future.



The items supplied with your product may vary

depending upon the model.



Product specifications or contents of this manual

may be changed without prior notice due to

upgrade of product functions.



For an optimal connection, HDMI cables and USB

devices should have bezels less than 10 mm (0.39

inches) thick and 18 mm (0.7 inches) width.



Use an extension cable that supports USB 2.0 if

the USB cable or USB flash drive does not fit into

your TV’s USB port.



Use a certified cable with the HDMI logo attached.

If you do not use a certified HDMI cable, the

screen may not display or a connection error may

occur.



Recommended HDMI cable types (3 m or less)

- High-Speed HDMI®/

cable

- High-Speed HDMI®/

cable with Ethernet

*A 10 mm (0.39 inches)

18 mm (0.7 inches)

CAUTION



Do not use any unapproved items to ensure the

safety and product’s lifespan.



Any damages or injuries by using unapproved

items are not covered by the warranty.



In case of some model, the thin film on screen is a

part of the TV, So don’t take it off.



When attaching the stand to the TV set, place the

screen facing down on a cushioned table or flat

surface to protect the screen from scratches.



Make sure that the screws are fastened tightly.

(If they are not fastened securely enough, the TV

may tilt forward after being installed.)



Do not tighten the screws with too much force;

otherwise they may be damaged and come loose

later.

Optional Extras

Optional extras can be changed or modified for

quality improvement without any notification.

Contact your dealer for buying these items.

These devices only work with certain models.

The model name or design may be changed

manufacturer’s circumstances or policies.

(Depending upon model)

AN-MR600

Magic Remote

AG-F***

Cinema 3D

Glasses

AN-VC550

Smart Camera

AG-F***DP

Dual Play

Glasses

LG Audio

Device

AN-WF500

Wi-Fi/

Bluetooth

DONGLE

ENGLISH



When holding the TV, the screen

should face away from you to

avoid damage.



Hold the top and bottom of the TV frame firmly.

Make sure not to hold the transparent part,

speaker, or speaker grille area.



Use at least two people to move a

large TV.



When transporting the TV by

hand, hold the TV as shown in the

following illustration.



When transporting the TV, do not expose the TV

to jolts or excessive vibration.



When transporting the TV, keep the TV upright;

never turn the TV on its side or tilt towards the left

or right.



When handling the TV, be careful not to damage

the protruding joystick button.

CAUTION



Avoid touching the screen at all times, as this may

result in damage to the screen.



Do not place the product on the floor with its

front facing down without padding. Failure to do

so may result in damage to the screen.



Do not move the TV by holding the cable holder

or cable management, as the cable holders may

break, and injuries and damage to the TV may

occur. (Depending upon model)

Using the Joystick Button

(Image shown may differ from your TV.)

You can operate the TV by pressing the button or

moving the joystick left, right, up, or down.

Joystick Button

Maintenance

Cleaning Your TV

Clean your TV regularly to keep it at peak

performance and to extend the product lifespan.

CAUTION



Make sure to turn the power off and disconnect

the power cord and all other cables first.



When the TV is left unattended or unused for a

long time, disconnect the power cord from the

wall outlet to prevent possible damage from

lightning or power surges.

Screen, Frame, Cabinet, and Stand

To remove dust or light dirt, wipe the surface with a

dry, clean, and soft cloth.

To remove major dirt, wipe the surface with a soft

cloth dampened in clean water or a diluted mild

detergent. Then wipe immediately with a dry cloth.

CAUTION



Do not push, rub, or hit the surface with your

fingernail or a sharp object, as this may result in

scratches on the screen and image distortions.



Do not use any chemicals, such as waxes, benzene,

alcohol, thinners, insecticides, air fresheners,

lubricants, as these may damage the screen’s finish

and cause discoloration.



Do not spray liquid onto the surface. If water

enters the TV, it may result in fire, electric shock, or

malfunction.

Power Cord

Remove the accumulated dust or dirt on the power

cord regularly.

Lifting and Moving the TV

When moving or lifting the TV, read the following to

prevent the TV from being scratched or damaged

and for safe transportation regardless of its type and

size.



Move the TV in the box or packing material that

the TV originally came in.



Before moving or lifting the TV, disconnect the

power cord and all cables.

ENGLISH

Mounting on a Table

(Image shown may differ from your TV.)

Lift and tilt the TV into its upright position on a

table.

- Leave a 10 cm (4 inches) (minimum) space from

the wall for proper ventilation.

10 cm

(4 inches)

Connect the power cord to a wall outlet.

CAUTION



Do not place the TV near or on sources of heat, as

this may result in fire or other damage.

Using the Kensington Security

System (optional)

(Depending upon model)

(Image shown may differ from your TV.)

The Kensington security system connector is located

at the rear of the TV. For more information of

installation and using, refer to the manual provided

with the Kensington security system or visit

http://

www.kensington.com.

Connect the Kensington

security system cable between the TV and a table.

NOTE



The Kensington security system is optional. You can

obtain additional accessories from your local dealer.

Basic functions

When the TV is turned off, place

your finger on the joystick button,

press it once, and release it.

Power On

When the TV is turned on, place

your finger on the joystick button,

press it once for a few seconds,

and release it. All running apps will

close.

Power Off

Place your finger on the joystick

button and move it left or right to

adjust the volume level.

Volume Control

Place your finger on the joystick

button and move it up or down to

adjust the channel.

Channels

Control

NOTE



Move the joystick button up, down, left, or right.

Be careful not to press it. If you press it first, you

may not be able to adjust the volume or scroll

through the channels.

Adjusting the Menu

When the TV is turned on, press the joystick button

one time. You can adjust the menu items moving the

joystick button up, down, left, or right.

Turns the power off.

Accesses the quick settings. (Depending upon

model)

Clears on-screen displays and returns to TV

viewing.

Changes the input source.

ENGLISH

10 cm

(4 inches)

Make sure to use screws and wall mounts that meet

the VESA standard. Standard dimensions for the wall

mount kits are described in the following table.

Model

40/43LF6300

32LF595B

43LF5900

43LH5800

42/50/55LF6500

55LF5950

VESA (A x B)

200 x 200 400 x 400

Standard screw

M6 M6

Number of screws

4 4

Wall mount bracket

(optional)

LSW240B

MSW240

LSW440B

MSW240

Model

49/55LF6300

49LF5900

60/65LF6300

60/65LF6390

65LF6350

VESA (A x B)

300 x 300 300 x 300

Standard screw

M6 M6

Number of screws

4 4

Wall mount bracket

(optional)

LSW350B

MSW240

LSW350B

CAUTION



Disconnect the power before moving or installing

the TV. Otherwise electric shock may occur.



Remove the stand before installing the TV on a

wall mount by performing the stand attachment

in reverse.



If you install the TV on a ceiling or slanted wall,

it may fall and result in severe injury. Use an

authorized LG wall mount and contact the local

dealer or qualified personnel. When using a

third-party wall mount, it is not covered by the

warranty.



Do not overtighten the screws as this may cause

damage to the TV and void your warranty.



Use the screws and wall mounts that meet the

VESA standard. Any damages or injuries by misuse

or using an improper accessory are not covered

by the warranty.

Securing the TV to a Wall (optional)

(Depending upon model)

(Image shown may differ from your TV.)

Insert and tighten the eye-bolts, or TV brackets

and bolts on the back of the TV.

- If there are bolts inserted at the eye-bolts

position, remove the bolts first.

Mount the wall brackets with the bolts to the

wall. Match the location of the wall bracket and

the eye-bolts on the rear of the TV.

Connect the eye-bolts and wall brackets tightly

with a sturdy rope or cable. Make sure to keep

the rope parallel to the flat surface.

CAUTION



Make sure that children do not climb on or hang

on the TV.

NOTE



Use a platform or cabinet that is strong and large

enough to support the TV securely.



Brackets, bolts, and ropes are optional. You can

obtain additional accessories from your local

dealer.

Mounting on a Wall

An optional wall mount can be used with your LG

television. Consult with your local dealer for a wall

mount that supports the VESA standard used by your

TV model. Carefully attach the wall mount bracket

at the rear of the TV. Install the wall mount bracket

on a solid wall perpendicular to the floor. If you are

attaching the TV to other building materials, please

contact qualified personnel to install the wall mount.

Detailed instructions will be included with the wall

mount. We recommend that you use an LG brand

wall mount. The LG wall mount is easy to adjust or to

connect the cables. When you do not use LG’s wall

mount bracket, use a wall mount bracket where the

device is adequately secured to the wall with enough

space to allow connectivity to external devices. If you

are using a non-adjustable mount, attach the mount

to the wall. Attach the cables to the TV first, then attach

the TV to the mount.

ENGLISH

NOTE



If you record a TV program on a DVD recorder or

VCR, make sure to connect the TV signal input

cable to the TV through a DVD recorder or VCR.

For more information of recording, refer to the

manual provided with the connected device.



The external device connections may differ from

the model.



Connect external devices to the TV regardless of

the order of the TV port.



If you connect a gaming device to the TV, use the

cable supplied with the gaming device.



Refer to the external equipment’s manual for

operating instructions.



In PC mode, there may be noise associated

with the resolution, vertical pattern, contrast

or brightness. If noise is present, change the PC

output to another resolution, change the refresh

rate to another rate or adjust the brightness and

contrast on the PICTURE menu until the picture is

clear.



Depending upon the graphics card, some

resolution settings may not allow the image to be

positioned on the screen properly.



Some USB Hubs may not work. If a USB device

connected through a USB Hub is not detected,

connect it directly to the USB port on the TV.



Smart TV Only) The TV may be capable of

operating without a set-top from a multichannel

video programming distributor (MVPD).

Connecting to an Antenna or Cable

Connect an antenna, cable, or cable box to watch

TV. The RF cable may not be supplied, depending

upon the model.

CAUTION



Make sure not to bend the copper wire of the RF

cable.

Copper wire



Complete all connections between devices, and

then connect the power cord to the power outlet

to prevent damage to your TV.

NOTE



Use the screws that are listed on the VESA

standard screw specifications.



The wall mount kit includes an installation manual

and necessary parts.



The wall mount bracket is optional. You can obtain

additional accessories from your local dealer.



The length of screws may differ depending upon

the wall mount. Make sure to use the proper

length.



For more information, refer to the manual

supplied with the wall mount.



When using the wall mounting bracket, apply

the adhesive protective label to cover the

unused stand opening(s). This will prevent the

accumulation of dust and dirt. (Use only when

provided with your particular model.)

Provided Item

Adhesive Protective Label



When attaching a wall mounting bracket to the

TV, insert the wall mount inner spacers into the

TV wall mount holes to adjust the vertical angle

of the TV. (Use only when provided with your

particular model.)

Provided Item

Wall Mount Spacer

Connections (Notifications)

You can connect various external devices to the TV.

Supported external devices are: HD receivers, DVD

players, VCRs, audio systems, USB storage devices,

PC, gaming devices, and other external devices. For

more information on external device’s connection,

refer to the manual provided with each device.

ENGLISH

NOTE



Use a signal splitter to use 2 TVs or more.



DTV Audio Supported Codec : MPEG, Dolby

Digital.

Other Connections

Connect your TV to external devices. For the best

picture and audio quality, connect the external

device and the TV with the HDMI cable. Depending

upon the model, a cable may not be provided.

NOTE



HDMI Audio Supported Format : PCM (32 kHz /

44.1 kHz / 48 kHz / 96 kHz / 192 kHz)

(Depending upon model)

Remote Control

(Depending upon model)

The descriptions in this manual are based on

the buttons on the remote control. Please read

this manual carefully and use the TV correctly. To

install batteries, open the battery cover, replace

batteries (1.5 V AAA) matching the and ends

to the label inside the compartment, and close the

battery cover. Failure to match the correct polarities

of the battery may cause the battery to burst or

leak, resulting in fire, personal injury, or ambient

pollution.To remove the batteries, perform the

installation actions in reverse. This remote uses

infrared light. When in use, it should be pointed in

the direction of the TV’s remote sensor.

CAUTION



Do not mix old and new batteries, as this may

damage the remote control.

(POWER) Turns the TV on or off.

Changes the input source.

Activates or deactivates the subtitles.

(User Guide) Sees user-guide.

Resizes an image.

Returns to the last TV channel.

Number button Enters numbers.

- (Dash) Inserts a dash between numbers such as

2-1 and 2-2.

Accesses the saved channel list.

Alternates between the two last channels

selected (pressing repeatedly).

Adjusts the volume level.

Accesses your favorite channel list.

Shows information on the current program.

Mutes all sounds.

Scrolls through the saved channels.

Moves to the previous or next screen.

Shows the previous history.

(Home) Accesses the Home menu.

Shows the list of Apps.

Accesses the quick settings.

Shows the list of Channels.

Navigation buttons Scrolls through menus or

options. (up/down/left/right)

Selects menus or options and confirms your

input.

Returns to the previous screen.

Clears all on-screen displays and returns to TV

viewing.

Sets the length of time until the TV to turns off.

Enables SAP (Secondary Audio Program) Feature.

Control buttons ( , , , , ) Controls the

SIMPLINK compatible devices (USB, SIMPLINK).

Color buttons These access special functions in

some menus. ( , , , )

Magic Remote Functions

(Depending upon model)

When the message

Magic remote control battery

is low. Change the battery.

is displayed, replace the

battery. To install batteries, open the battery cover,

replace batteries (1.5 V AA) matching

and ends

to the label inside the compartment, and close the

battery cover. Failure to match the correct polarities

ENGLISH

of the battery may cause the battery to burst or leak,

resulting in fire, personal injury, or ambient pollution.

Be sure to point the remote control at the remote

control sensor on the TV. To remove the batteries,

perform the installation actions in reverse.

This remote uses infrared light. When in use, it

should be pointed in the direction of the TV’s

remote sensor.

CAUTION



Do not mix old and new batteries, as this may

damage the remote control.

(POWER) Turns the TV on or off.

(INPUT) Changes the input source.

* Pressing and holding the (INPUT) button

displays all the lists of external inputs.

Number buttons Enters numbers.

(DASH) Inserts a dash between numbers such as

2-1 and 2-2.

Accesses the saved channel list.

Views the information of the current channels

and screen.

Adjusts the volume level.

(MUTE) Mutes all sounds.

* By pressing and holding the button, video

descriptions function will be enabled.

* (Secondary Audio Program) Feature can also be

enabled by pressing the key.

Scrolls through the saved channels.

(Home) Accesses the Home menu.

(BACK) Returns to the previous screen.

Clears all on-screen displays and returns to TV

viewing.

Wheel (OK) Press the center of the Wheel button to

select a menu. You can change channels by using the

Wheel button.

(up/down/left/right) Press the up, down,

left or right button to scroll the menu. If you press

buttons while the pointer is in use, the pointer

will disappear from the screen and Magic Remote will

operate like a general remote control. To display the

pointer on the screen again, shake Magic Remote to the

left and right.

(Q. Settings) Accesses the Quick Settings.

* Pressing and holding the (Q. Settings) button

displays the Advanced menu.

(Screen remote) Displays the Screen Remote.

* Accesses the Universal Control Menu in some regions.

Used for viewing 3D video. (For 3D models)

(Voice recognition)

Network connection is required to use the voice

recognition function.

1. Press the voice recognition button.

2. Speak when the voice display window appears on the

TV screen.

* Use the Magic Remote no further than 10 cm (4 inches)

from your face.

* The voice recognition may fail when you speak too fast

or too slowly.

* The recognition rate may vary depending upon the

user’s characteristics (voice, pronunciation, intonation,

and speed) and the environment (noise and TV volume).

Activates or deactivates the subtitles.

Color buttons These access special functions in some

menus. ( Red, Green, Yellow, Blue)

ENGLISH

Registering Magic Remote

How to register the Magic Remote

(Wheel)

To use the Magic Remote, first pair it

with your TV.

1 Put batteries into the Magic Remote

and turn the TV on.

2 Point the Magic Remote at your TV

and press the Wheel (OK) on the

remote control.

* If the TV fails to register the Magic

Remote, try again after turning the TV

off and back on.

How to deregister the Magic Remote

(BACK)

(Home)

Press the

(BACK) and (Home)

at the same time, for five seconds, to

unpair the Magic Remote with your TV.

Pressing and holding the

button

will let you cancel and re-register

Magic Remote at once.

How to use Magic Remote

 Shake the Magic Remote slightly to

the right and left or press

(Home),

(INPUT), buttons to make the

pointer appear on the screen. (In some

TV models, the pointer will appear

when you turn the Wheel button.)

 If the pointer has not been used for a

certain period of time or Magic Remote is

placed on a flat surface, then the pointer

will disappear.

 If the pointer does not move as you

wish, shake Magic Remote to the left

and right. The pointer will move to the

center of the screen.

 The Magic Remote depletes batteries

faster than a normal remote due to the

additional features.

Precautions to Take



Use the remote control within the specified

range (within 10 m, 32.8 ft.) You may experience

communication failures when using the device

outside the coverage area or if there are obstacles

within the coverage area.



You may experience communication failures

depending upon the accessories. Devices such

as a microwave oven and wireless LAN operate in

the same frequency band (2.4 GHz) as the Magic

Remote. This may cause communication failures.



The Magic Remote may not work properly if a

wireless router (AP) is within 1 m (3.28 ft) of the

TV. Your wireless router should be more than

1 m (3.28 ft) away from the TV.



Do not disassemble or heat the battery.



Do not drop the battery. Avoid extreme shocks to

the battery.



Inserting the battery in the wrong way may result

in explosion.

Licenses

Supported licenses may differ by model. For more

information about licenses, visit

www.lg.com

(For LF6300, LF6390,

LF6500, LF6350 series)

(For LF595B, LF5900,

LF5950, LH5800 series)

Open Source Software

Notice Information

To obtain the source code under GPL, LGPL, MPL,

and other open source licenses, that is contained in

this product, please visit

http://opensource.lge.com

In addition to the source code, all referred license

terms, warranty disclaimers and copyright notices

are available for download.

LG Electronics will also provide open source code

to you on CD-ROM for a charge covering the cost

of performing such distribution (such as the cost of

media, shipping, and handling) upon email request

[email protected]om

. This offer is valid for three

(3) years from the date on which you purchased the

product.

ENGLISH

Troubleshooting



Cannot control the TV with the remote control.

- Check the remote control sensor on the product

and try again.

- Check if there is any obstacle between the

product and the remote control.

- Check if the batteries are still working and

properly installed (

, to

)



No image display and no sound is produced.

- Check if the product is turned on.

- Check if the power cord is connected to a wall

outlet.

- Check if there is a problem in the wall outlet by

connecting other products.



The TV turns off suddenly.

- Check the power control settings. The power

supply may be interrupted.

- Check if the Sleep Timer/Timer Power off is

activated in the Timers settings.

- If there is no signal while the TV is on, the TV

will turn off automatically after 15 minutes of

inactivity.

Specifications

Product specifications may be changed without

prior notice due to upgrade of product functions.

Television System

NTSC-M, ATSC, 64 & 256 QAM

Program Coverage

VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV

1-135

External Antenna Impedance

75 Ω

Environment Condition

Operating Temperature 0 °C to 40 °C (32 °F to 104 °F)

Operating Humidity Less than 80 %

Storage Temperature -20 °C to 60 °C (-4 °F to 140 °F)

Storage Humidity Less than 85 %

Wireless Module Specifications

(For LF595B, LF5900, LF5950, LH5800 series)

Wireless Module (WN8122E1) Specification

Standard IEEE802.11a/b/g/n

Frequency Range

2400 to 2483.5 MHz

5150 to 5250 MHz

5725 to 5850 MHz

Output Power

(Max.)

802.11a : 16.5 dBm

802.11b : 16 dBm

802.11g : 15.5 dBm

802.11n - 2.4 GHz : 15.5 dBm

802.11n - 5 GHz: 16.5 dBm

 Because band channel used by the country could

be different, the user can not change or adjust the

operating frequency and this product is set for the

regional frequency table.

 This device should be installed and operated with

minimum distance 20 cm (7.8 inches) between

the device and your body. And this phrase is for

the general statement for consideration of user

environment.

 Contains FCC ID: BEJWN8122E1

Contains IC: 2703H-WN8122E1

(For LF6300, LF6390, LF6500, LF6350 series)

Wireless module (LGSBW41) Specifications

Wireless LAN Bluetooth

Standard IEEE 802.11a/b/g/n Bluetooth Version 4.0

Frequency

Range

2400 to 2483.5 MHz

5150 to 5250 MHz

5725 to 5850 MHz

2400 to 2483.5 MHz

Output

Power

(Max.)

802.11a: 11.5 dBm

802.11b: 11 dBm

802.11g: 10.5 dBm

802.11n - 2.4 GHz:

11 dBm

802.11n - 5 GHz:

12.5 dBm

10 dBm or Lower

 Because band channel used by the country could

be different, the user can not change or adjust the

operating frequency and this product is set for the

regional frequency table.

 This device should be installed and operated with

minimum distance 20 cm (7.8 inches) between

the device and your body. And this phrase is for

the general statement for consideration of user

environment.

 Contains FCC ID: BEJLGSBW41

Contains IC: 2703H-LGSBW41

External Control Device

Setup

To obtain the external control device setup

information, please visit

www.lg.com

LG Customer Information Center

For inquires or comments, visit www.lg.com or call;

1-888-542-2623 CANADA

1-800-243-0000 USA, Consumer User

1-888-865-3026 USA, Commercial User

www.lg.com

The model and serial number of the TV are located on the

back and one side of the TV.

Record them below should you ever need service.

MODEL

SERIAL

Declaration of Conformity

Trade Name LG

Model 42LF6500-UB, 50LF6500-UB

55LF6500-UB, 65LF6350-UA

40LF6300-UA, 43LF6300-UA

49LF6300-UA, 55LF6300-UA

60LF6300-UA, 65LF6300-UA

60LF6390-UA, 65LF6390-UA

32LF595B-UB, 43LF5900-UB

49LF5900-UB, 55LF5950-UB

43LH5800-UD

Responsible

Party

LG Electronics Inc.

Address 1000 Sylvan Ave.

Englewood Cliffs NJ 07632

U.S.A

TEL 201 - 266 - 2534

OWNER’S MANUAL

EXTERNAL CONTROL

DEVICE SETUP

Please read this manual carefully before operating the set and retain it for

future reference.

www.lg.com

ENG

ENGLISH

KEY CODES

• This feature is not available for all models.

Code

(Hexa)

Function Note

Code

(Hexa)

Function Note

00 CH +, PR + R/C Button 53 List R/C Button

01 CH -, PR - R/C Button 5B Exit R/C Button

02 Volume + R/C Button 60 PIP(AD) R/C Button

03 Volume - R/C Button 61 Blue R/C Button

06 > (Arrow Key / Right Key) R/C Button 63 Yellow R/C Button

07 < (Arrow Key / Left Key) R/C Button 71 Green R/C Button

08 Power R/C Button 72 Red R/C Button

09 Mute R/C Button 79 Ratio / Aspect Ratio R/C Button

0B Input R/C Button 91 AD (Audio Description) R/C Button

0E SLEEP R/C Button 7A User Guide R/C Button

0F TV, TV/RAD R/C Button 7C Smart / Home R/C Button

10 - 19 * Number Key 0 - 9 R/C Button 7E SIMPLINK R/C Button

1A Q.View / Flashback R/C Button 8E ►► (Forward) R/C Button

1E FAV (Favorite Channel) R/C Button 8F ◄◄ (Rewind) R/C Button

20 Text (Teletext) R/C Button AA Info R/C Button

21 T. Opt (Teletext Option) R/C Button AB Program Guide R/C Button

28 Return (BACK) R/C Button B0 ► (Play) R/C Button

30 AV (Audio / Video) Mode R/C Button B1

ꕗ (Stop / File List)

R/C Button

39 Caption/Subtitle R/C Button BA

ꕘ (Freeze / Slow Play /

Pause)

R/C Button

40 Λ

(Arrow Key / Cursor Up)

R/C Button BB Soccer R/C Button

V (Arrow Key / Cursor

Down)

R/C Button BD

ꔄ (REC)

R/C Button

42 My Apps R/C Button DC 3D R/C Button

43 Menu / Settings R/C Button 99 AutoConfig R/C Button

44 OK / Enter R/C Button 9F App / * R/C Button

45 Q.Menu R/C Button

4C List, - (ATSC Only) R/C Button

* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.

(For South Korea, Japan, North America, Latin America except Colombia models)

ENGENGLISH

EXTERNAL CONTROL DEVICE SETUP

• Image shown may differ from your TV.

Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer

or an A/V control system) to control the product’s functions externally.

Note: The type of control port on the TV can be different between model series.

* Please be advised that not all models support this type of connectivity.

* Cable is not provided.

USB to Serial converter with USB Cable

USB Type

USB IN

(TV)

(PC )

RS-232C IN

(CONTROL & SERVICE)

(TV)

(PC )

(TV)

(PC )

SERVICE ONLY

RS-232C IN

(CONTROL & SERVICE)

RS-232C IN

(CONTROL & SERVICE)

• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter

which is not made nor provided by LG.

• It can be purchased from computer stores that carry accessories for IT support professionals.

RS-232C With RS232C Cable

DE9 (D-Sub 9pin) Type

• You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C cable required

for the connection between the PC and the TV, which is specified in the manual.

USB IN

(TV)

(PC )

RS-232C IN

(CONTROL & SERVICE)

(TV)

(PC )

(TV)

(PC )

SERVICE ONLY

RS-232C IN

(CONTROL & SERVICE)

RS-232C IN

(CONTROL & SERVICE)

The connection interface may differ from your TV.

ENG

ENGLISH

EXTERNAL CONTROL DEVICE SETUP

Phone jack Type

• You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and

the TV, which is specified in the manual.

* For other models, connect to the USB port.

* The connection interface may differ from your TV.

USB IN

(TV)

(PC )

RS-232C IN

(CONTROL & SERVICE)

(TV)

(PC

)

(TV)

(PC )

SERVICE ONLY

RS-232C IN

(CONTROL & SERVICE)

RS-232C IN

(CONTROL & SERVICE)

- or

USB IN

(TV)

(PC )

RS-232C IN

(CONTROL & SERVICE)

(TV)

(PC )

(TV)

(PC

)

SERVICE ONLY

RS-232C IN

(CONTROL & SERVICE)

RS-232C IN

(CONTROL & SERVICE)

Customer Computer RS-232C configurations

3-Wire Configurations(Not standard)

PC TV

RXD 2 2 TXD

TXD 3 1 RXD

GND 5 3 GND

RXD 3 2 TXD

TXD 2 1 RXD

GND 5 3 GND

D-Sub 9 Phone

RS-232C

(Serial port)

Set ID

For Set ID number, see "Real Data Mapping" on p.6

1. Press SETTINGS to access the main menus.

2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.

3. Press the Navigation buttons to scroll to SET ID and press OK.

4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.

5. When you are finished, press EXIT.

* (Depending on model)

La page charge ...

LG 65LF6350 Le manuel du propriétaire

Marque: LG

Modèle: 65LF6350

Catégorie: Téléviseurs LCD

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: LG 65LF6350 Owner's manual

LG 65LF6350 Le manuel du propriétaire

LG 65LF6350 Le manuel du propriétaire

dans d''autres langues

Documents connexes