Chief K0W1I2B Guide d'installation

Catégorie
Kits de montage
Taper
Guide d'installation

Ce manuel convient également à

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Wall Mount with iPad
®
2 and iPad
®
3 Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
K0W1I2B/K0W1I2TB
K0W1I2B/K0W1I2TB Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
iPad® is a registered trademark of Apple Inc.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the K0W1I2B/K0W1I2TB up
to (and including) the display does not exceed 25 lbs
(11.34 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
Installation Instructions K0W1I2B/K0W1I2TB
3
DIMENSIONS
K0W1I2B
3.94
100.0
K0W1I2TB
11.25
285.8
K0W1I2B/K0W1I2TB Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions K0W1I2B/K0W1I2TB
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/8" (included)
3/16" (included)
A (1)
B (4)
M4x14mm
C (4)
M4x25mm
D (4)
M10x5.3x10
E (1)
[wall bracket]
F (2)
1/4 x 2 1/2"
G (2)
1/4"
H (1)
[FSBI2B mount]
J (1)
[FSBI2TB mount]
or
+ hardware and
installation instructions
+ hardware and
installation instructions
[Wall mount]
* B, C and D for use only if
iPad
®
interface is not used.
K0W1I2B/K0W1I2TB Installation Instructions
6
Assembly And Installation
Connecting Wall Mount to Wall
1. Determine mounting location on wall.
2. Use a stud finder to locate stud.
3. Use wall bracket to mark and drill two 3/16" x 2 1/2" holes in
wall at desired mounting location. (See Figure 1)
4. Use two 1/4-2 1/2" hex head lag screws (F) and two 1/4"
washers (G) to install wall bracket (E) onto wall. (See
Figure 1)
IMPORTANT ! : Overtightening screws (F) may cause
bracket to compress into soft wall surface resulting in
difficult mount installation or improper engaging of set
screw in Step 6.
5. Hang wall mount (A) over wall bracket (E). (See Figure 1)
6. Secure wall mount (A) to wall bracket (E) by tightening set
screw. Ensure set screw engages back side of wall bracket
(E) to properly secure mount. (See Figure 1)
Figure 1
iPad
®
Installation
Refer to FSBIB/FSBIB2 or FSBI2TB installation instructions to
install iPad
®
(not included) to wall mount.
Head Tilt Adjustment
1. Adjust head tilt to desired tilt position. (See Figure 2)
2. Adjust head tilt tension screw to change the adjustment
tension. (See Figure 2)
Figure 2
Portrait Adjustment
The iPad may be adjusted 90 degrees in either direction in order
to provide a portrait view of the iPad. (See Figure 3)
Figure 3
(F) x 2
(E)
(G) x 2
3
4
5
set screw
6
side view
(E)
3/16" x 2 1/2"
(A)
head tilt tension
(K0W1I2B shown)
(K0W1I2B shown)
Installation Instructions K0W1I2B/K0W1I2TB
7
K0W1I2B/K0W1I2TB Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002201 Rev02
2012 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
09/12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief K0W1I2B Guide d'installation

Catégorie
Kits de montage
Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues