IKEA RIWM60 Manuel utilisateur

Catégorie
Machines à laver
Taper
Manuel utilisateur
RENLIG
IWM60
GB
DE
FR
IT
ENGLISH 4
DEUTSCH 25
FRANÇAIS 50
ITALIANO 76
Contents
Safety information 4
Product description 6
Control panel 7
First use 9
Daily use 9
Helpful hints and tips 12
Washing programmes 12
Consumption values 15
Care and cleaning 15
What to do if… 18
Technical data 20
Installation 21
Electrical connection 22
Environment concerns 22
IKEA GUARANTEE 22
Subject to change without notice
Safety information
For your safety and correct operation of
the appliance, read this manual carefully
before installation and use. Always keep these
instructions with the appliance even if you
move or sell it. Users must fully know the oper-
ation and safety features of the appliance.
The manufacturer is not responsible for dam-
ages caused by incorrect installation and use.
Children and vulnerable people safety
Do not let persons, children included, with
reduced physical sensory, reduced mental
functions or lack of experience and knowl-
edge to use the appliance. They must have
supervision or instruction for the operation
of the appliance by a person who is respon-
sible for their safety.
Keep all packaging well away from chil-
dren. There is risk of suffocation.
Keep all detergents in a safe area. Do not
let children touch the detergents.
Make sure that children or pets do not climb
into the drum. Please check into the drum
before using it.
This appliance incorporates a special fea-
ture to prevent children and pets becoming
trapped inside the drum.
To activate this de-
vice, rotate the but-
ton clockwise (with-
out pressing it) in-
side the door until
the groove is hori-
zontal. If necessary
use a coin.
To disable this de-
vice and restore the
possibility of closing
the door, rotate the
button anticlock-
wise until the
groove is vertical.
General safety
Do not change the specifications or modify
this product. There is risk of injury and dam-
age to the appliance.
If the appliance is delivered in the winter
months when there are minus temperatures,
store it at room temperature for 24 hours
before using for the first time. Please read
the “dangers of freezing” chapter.
This appliance is designed for use in normal
inside temperature. Manufacturer is not re-
sponsible for freezing damages.
Always unplug the appliance and turn off
the water supply after use, cleaning and
maintenance.
ENGLISH 4
Installation
A qualified and competent person must do
the electrical and the plumbing installation.
This appliance is heavy. Take care when you
move it.
Make sure that the appliance is not dam-
aged because of transport. Do not connect
a damaged appliance. If necessary, contact
dedicated After Sales Service.
Remove all packaging and transit bolts be-
fore first use. Serious damage can occur to
the appliance or to neighbouring cabinets
or furniture.
Keep all transit devices so that they can be
refitted if the appliance ever has to be trans-
ported again. Please refer to the relevant
steps in the Assembly Instruction.
Never place cardboard, wood or similar
materials under the appliance to compen-
sate for any unevenness in the floor.
Level accurately the appliance and tight the
lock nuts to prevents vibration, noise and
displacement of the appliance during oper-
ation.
If your appliance is installed on a carpeted
floor, adjust the feet in order to ensure that
the air must circulate freely under the appli-
ance.
Check that your appliance is not standing on
the inlet and drain hose and the worktop or
the back of the appliance is not pressing the
electrical supply cable against the wall.
Always be sure, that there is no water leak-
age from hoses and their connections after
the installation.
If the appliance is installed in a location sub-
ject to frost, please read the “dangers of
freezing” chapter.
Use
The appliance is only for domestic use. Do
not use the appliance for commercial and
industrial use or for other uses.
Only an authorised service engineer can re-
pair this appliance. Use only original spare
parts.
Refer to the instructions on the label of each
item (garment) before washing.
Do not overload the appliance. See the
Washing Programme Table.
Before washing, ensure that all pockets are
empty and buttons and zips are fastened.
Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp ma-
terial can cause extensive damage and must
not be placed into the appliance.
Treat stains such as paint, ink, rust, and grass
before washing.
Only use the advised quantities of fabric
softener and detergent. Damage to the fab-
ric can ensue if you overfill. Refer to the man-
ufacturer’s recommendations of quantities.
Wash small items such as socks, laces, wash-
able belts etc. in a washing bag or pillow
case as it is possible for such items to slip
down between the tub and the inner drum.
Do not use your appliance to wash articles
with whalebones, items without hems,
frayed and torn. Underwired bras must NOT
be washed.
Garments which have been in contact with
volatile petroleum products should not be
appliance washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the appliance.
The water we use normally contains lime. It
is a good idea to periodically use a water
softening powder in the appliance. Do this
without any laundry into the drum and ac-
cording to the softening powder manufac-
turer’s instructions. This will help to prevent
the formation of lime deposits making your
appliance more efficiency.
Never pull the power supply cable to re-
move the plug from the socket; always take
hold of the plug itself.
Never use the appliance if the power supply
cable, the control panel, the working surface
or the base is damaged so that the inside of
the appliance is accessible.
Water inlet
This appliance must be connected to a cold
water supply.
Do not use connection hoses from an old
appliance to connect it to the water supply.
ENGLISH 5
The water pressure must be in the limits (re-
fer to the chapter «Technical data» table).
Make sure that the local water authority
gives you the average mains pressure in
your area.
Make sure that there are no kinks in the wa-
ter inlet hose and that the water inlet hose
is not squashed or entangled.
Before connecting up the appliance to new
pipework or to pipework that has not been
used for some time, run off a reasonable
amount of water to flush out any debris that
may have collected in the pipes.
Turn the inlet hose on the back of the appli-
ance to the left or the right to suit the instal-
lation.
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the
tap, you will have to purchase a new, longer
hose specially designed for this type of use.
Before opening the water tap, be sure to
tighten the ring nut well to prevent any leaks.
Water drainage
Make sure the end of the drain hose cannot
come unhooked when the appliance is emp-
tying. This could be done by tying it to the
tap with a piece of string or attaching it to
the wall.
The drain hose must be placed at a height
of not less than 44 cm and not more than 90
cm. Please refer to the Assembly Instruction
booklet.
Care and cleaning
Before maintenance, switch off the appli-
ance and disconnect the mains plug from the
mains socket.
Clean the exterior cabinet of the appliance
with soap and water only, and then dry
thoroughly.
The washing powder and additive dispens-
er drawer should be cleaned regularly.
Inspected the pump regularly and particu-
larly if:
– the appliance does not empty and/or
spin
– the appliance makes an unusual noise
during draining due to objects such as
safety pins, coins etc. blocking the pump.
Never remove the pump cover during a
wash cycle. Always wait until the appliance
has drained out the water. If you have se-
lected an high temperature washing pro-
gramme please wait until the water has
cooled down.
Ensure that the pump cover is securely re-
tightened to prevent any leaks.
Product description
1
2
3
4
5
6
1 Detergent dispenser drawer
2 Control panel
3 Door opening handle
4 Rating Plate
5 Drain pump
6 Adjustable feet
ENGLISH 6
Detergent dispenser drawer
Compartment for detergent used for pre-
wash and soak phase or for stain remover
used during the stain action phase (if avail-
able). The prewash and soak detergent is
added at the beginning of the wash pro-
gramme. The stain remover is added during
the stain action phase.
Compartment for powder or liquid deter-
gent used for main wash. If using liquid de-
tergent pour it just before starting the pro-
gramme.
Compartment for liquid additives (fabric
softener, starch).
Follow the product manufacturer’s rec-
ommendations on quantities to use and
do not ever exceed the «MAX» mark in the
detergent dispenser drawer. Any fabric soft-
ener or starching additives must be poured
into the compartment before starting the
wash programme.
Control panel
Below is a picture of the control panel. It shows the programme selector dial as well as the
buttons and the indicator lights. These are presented by relevant numbers on the following
pages.
1 2 3 4 5 6 7
1 Programme selector dial
2 Spin reduction button
3 Multi-Functions button
4 Extra Rinse button
5 Start/Pause button
6 Delay Start button
7 Programme Indicator lights
ENGLISH 7
Table of Symbol
= Cottons
= On/Off - Reset
= Economy
= Rinse Hold
= Cold wash = Options
= Synthetics = Prewash
= Easy Iron = Quick Wash
= Delicates = Extra Rinse
= Wool = Delay Start
= Handwash = Main Wash
= Rinses = End Cycle
= Drain = Start/Pause
= Spin
Programme selector dial It allows you to switch the appliance On/Off and/or to select a
programme.
Spin reduction button By pressing this button you can change the spin speed of the
selected programme.
Rinse Hold option: by selecting this option the water of the last
rinse is not emptied out to prevent the fabrics from creasing.
Before opening the door it will be necessary to empty out the
water. To empty out the water, please read the paragraph
«At the end of the programme».
Multi-Functions button: By pressing this button, you can select only one of the options.
The relevant light will light up.
Prewash: by selecting this option the appliance performs a
prewash cycle before the main wash phase. The washing time
will be prolonged. This option is recommended for heavily
soiled laundry.
Super Quick: a very short cycle for slightly soiled items that
have been worn for a short time.
Extra Rinse button This appliance is designed for saving energy. If it necessary to
rinse the laundry using an extra quantity of water (extra rinse),
select this option. Some additional rinses will be performed. This
option is recommended for people who are allergic to deter-
gents, and in areas where the water is very soft.
Start/Pause button This button allows you to start or to interrupt the selected wash-
ing programme.
Delay Start button This button allows you to delay the start of the programme by 3,
6 or 9 hours.
Programme Indicator lights
ENGLISH 8
7.1
7. 2
7. 3
When selecting a washing programme both lights 7.1 and 7.2
illuminate.
When you have pressed the button 5 the only light correspond-
ing to the running phase stays on.
The appliance starts working and the door is locked.
The light 7.3 illuminates at the end of the washing cycle. After a
few minutes the door can be opened.
Important! If the draining programme is selected any light will
illuminate.
First use
1. Ensure that the electrical and water con-
nections comply with the installation in-
structions.
2. Remove any material from the drum.
3. Pour 2 liters of water into the main wash
compartment
of the detergent drawer
in order to activate the ECO valve.
Select a cotton cycle at the highest tem-
perature without any laundry in the appli-
ance, to remove any manufacturing resi-
due from the drum and tub.
Pour 1/2 a measure of detergent into the
main wash compartment and start the ap-
pliance.
Daily use
Open the door
Open the door by carefully pulling the door
handle outwards.
Load the laundry
Place the laundry in
the drum, one item at
a time, shaking them
out as much as possi-
ble.
By pushing the port-
hole frame, close
firmly the door.
Measure out detergent and fabric softener
1
Pour the detergent
into the main wash
compartment
or
in the appropriate
compartment if the
selected pro-
gramme/option it re-
quires (see more de-
tails in "Detergent
dispenser drawer").
To pour the right
quantity of the deter-
gent, see more de-
tails in "Degrees of
water hardness".
ENGLISH 9
2 Pour fabric softener
into the compartment
marked
(must not
exceed the «MAX»
mark in the drawer).
Close the drawer gently
Select the required programme by turning
the programme selector dial (1)
The appliance is now switched on. The indica-
tor light of button 5 starts to blink.
At the end of the programme the selector dial
must be turned to position O , to switch the ap-
pliance off.
For the description of each wash cycle,
the compatibility among the washing
programmes and the options, consult the
chapter «Washing Programmes».
Caution! If you turn the programme
selector dial to another programme when
the appliance is working, the red indicator light
of button 5 will blink 3 times to indicate a
wrong selection. The appliance will not
perform the new selected programme.
Reduce the spin speed by pressing button 2
By selecting a programme, the appliance pro-
poses automatically the maximum spin speed
provided for that programme.
Press button 2 repeatedly to change the spin
speed, if you want your laundry to be spun at
a different speed. The relevant light illumi-
nates.
Select the available options by pressing
buttons 2, 3 and 4
Depending on the programme, different func-
tions can be combined. These must be selected
after choosing the desired programme and
before starting the programme.
When these buttons are pressed, the corre-
sponding indicator lights illuminate. When
they are pressed again, the indicator lights go
out. If an incorrect option is selected, the inte-
grated red indicator light of the button 5 flash-
es for 3 times.
For the compatibility among the washing
programmes and the options see chapter
«Washing Programmes».
Select the Delay Start by pressing button 6
Before you start the programme, if you wish to
delay the start, press the button 6 repeatedly,
to select the desired delay. The relevant light
illuminates.
You must select this option after you have set
the programme and before you start the pro-
gramme.
You can cancel or modify the delay time at any
moment, before you press button 5.
Selecting the delayed start:
1. Select the programme and the required
options.
2. Select the delay start by pressing the but-
ton 6.
3. Press button 5:
the appliance starts its countdown.
The programme will start after the se-
lected delay has expired.
Cancelling the delayed start after having star-
ted the programme:
1. Set the washing appliance to PAUSE by
pressing button 5.
2. Press button 6 once, the light relevant to the
selected delay goes off
3. Press button 5 again to start the pro-
gramme.
The Delay Start can not be selected with
DRAIN programme.
Important! The selected delay can be
changed only after selecting the washing
programme again.
The door will be locked throughout the delay
time. If you need to open the door, you must
set the appliance to PAUSE (by pressing the
button 5) and then wait a few minutes. After
you have closed the door, press the button 5
again.
ENGLISH 10
Start the programme by pressing button 5
To start the selected programme, press the
button 5, the corresponding green indicator
light stops blinking. The indicator light corre-
sponding to the running phase illuminates. The
appliance starts operating and the door is
locked.
To interrupt a programme which is running,
press the button 5: the corresponding green
indicator light starts blinking.
To restart the programme from the point at
which it was interrupted, press the button 5
again. If you have chosen a delayed start, the
appliance will begin the countdown.
If an incorrect option is selected, the red indi-
cator light of the button 5 blinks 3 times.
Altering an option or a running programme
It is possible to change some options before
the programme carries them out.
Before you make any change, you must PAUSE
the appliance by pressing the button 5.
Changing a running programme is possible
only by resetting it. Turn the programme se-
lector dial to O and then to the new pro-
gramme position. Start the new programme by
pressing the button 5 again. The washing wa-
ter in the tub will be not emptied out.
Interrupting a programme
Press the button 5 to interrupt a programme
which is running, the corresponding green in-
dicator light starts blinking.
Press the button again to restart the pro-
gramme.
Cancelling a programme
Turn the selector dial to O to cancel a pro-
gramme which is running.
You can select now a new programme.
Opening the door
After the programme has started the door is
locked. If, for any reason, you need to open it,
set firstly the appliance to PAUSE by pressing
the button 5. After a few minutes it will be pos-
sible to open the door.
If the door remains locked, this means that the
appliance is already heating or that the water
level is too high. In any case, do not try to force
the door!
If you cannot open the door but you need to
open it you have to switch the appliance off by
turning the selector dial to O . After a few mi-
nutes the door can be opened (pay attention
to the water level and temperature!).
After closing the door, it is necessary to select
the programme and options again and to
press button 5.
At the end of the programme
The appliance stops automatically. The indi-
cator light of button 5 and the indicator light
corresponding to the just finished washing
phase goes off. The light 7.3 illuminates. After
a few minutes the door can be opened.
If a programme or an option that ends with
water left in the tub has been selected, the light
7.3 illuminates but the door remains locked to
indicate that the water must be emptied out
before opening the door.
Follow the below instructions to empty out the
water:
1. Turn the programme selector dial to O .
2. Select the draining or spinning pro-
gramme.
3. Reduce the spin speed if needed, by press-
ing the button 2.
4. Press button 5.
At the end of the programme, the door can be
now opened. Turn the programme selector di-
al to O to switch the appliance off.
Remove the laundry from the drum and care-
fully check that the drum is empty. If you do not
intend to carry out another wash, close the
water tap. Leave the door open to prevent any
mildew and unpleasant smells.
Stand by : once the programme has fin-
ished the energy saving system is ena-
bled with the pilot lights switched on. By press-
ing any button the appliance will come out of
the energy saving status.
ENGLISH 11
Helpful hints and tips
Sorting out the laundry
Follow the wash code symbols on each gar-
ment label and the manufacturer’s washing in-
structions. Sort the laundry as follows: whites,
coloureds, synthetics, delicates, woollens.
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable
to treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
stain remover product then rub in the soap and
water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with
rust stains which are not recent since the cel-
lulose structure will already have been dam-
aged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(white cottons and fast coloureds only).
Grass: soap lightly and treat with bleach
(white cottons and fast coloureds only).
Ball point pen and glue: moisten with ace-
tone
1)
, lay the garment on a soft cloth and dab
the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Treat any
residual marks with bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone
1)
, then with acetic
acid; treat any residual marks on white fabrics
with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, me-
thylated spirits or benzine, then rub with de-
tergent paste.
Degrees of water hardness
Water hardness is classified in so-called “de-
grees” of hardness. Information on hardness of
the water in your area can be obtained from
the relevant water supply company, or from
your local authority.
Characteristic
Degrees of water hardness
German °dH French °T.H.
Soft 0-7 0-15
Medium 8-14 16-25
Hard 15-21 26-37
Very hard > 21 > 37
A water softener must be added when water has a medium-high degree of hardness. Follow
the manufacturer’s instructions. The quantity of detergent can then always be adjusted (re-
duced) to degree of hardness soft.
Washing programmes
Please always refer to the care label symbol of your garment and select the washing pro-
gramme based on what it says.
1) do not use acetone on artificial silk
ENGLISH 12
Programme/
Temperature
Type of
laundry
Cycle
Description
Max. Load
Red. Load
1)
Available
Options
Detergent
Compartment
COTTONS
90°-60°
White cotton (heavy-
normally soiled items).
Main wash
Rinses
Max. final
spin at 1200
rpm
6 kg
3 kg
1)
Spin
Rinse Hold
Prewash
Super Quick
Extra Rinse
2)
COTTONS
ECO
60°
White and fast col-
oured cotton econo-
my, lightly-heavy
soiled items, shirts, un-
derwear.
Main wash
Rinses
Max. f inal
spin at 1200
rpm
6 kg
Spin
Rinse Hold
Prewash
Extra Rinse
2)
COTTONS
40°-30°-Cold
Coloured cotton (nor-
mally-lightly soiled
items).
Main wash
Rinses
Max. final
spin at 1200
rpm
6 kg
3 kg
1)
Spin
Rinse Hold
Prewash
Super Quick
Extra Rinse
2)
SYNTHETICS
60°-40°-30°-
Cold
Synthetic or mixed
fabrics: underwear,
coloured garments,
non-shrink shirts, blou-
ses.
Main wash
Rinses
Max. final
spin at 900
rpm
3 kg
1.5 kg
1)
Spin
Rinse Hold
Prewash
Super Quick
Extra Rinse
2)
EASY IRON
40°
Synthetic fabrics: se-
lecting this pro-
gramme the laundry is
gently washed and
spun to avoid any
creasing. In this way
ironing is easier. Fur-
thermore the appli-
ance will perform ad-
ditional rinses.
Main wash
Rinses
Max. final
spin at 900
rpm
1.5 kg
Spin
Rinse Hold
Prewash
Extra Rinse
2)
DELICATES
40°-30°-Cold
Delicate fabrics: for
example curtains.
Main wash
Rinses
Max. final
spin at 700
rpm
3 kg
1.5 kg
1)
Spin
Rinse Hold
Prewash
Super Quick
Extra Rinse
2)
ENGLISH 13
Programme/
Temperature
Type of
laundry
Cycle
Description
Max. Load
Red. Load
1)
Available
Options
Detergent
Compartment
WOOL
40°
Special programme
for wool garments
bearing the «Pure new
wool, non-shrink, ap-
pliance washable» la-
bel.
Main wash
Rinses
Max. final
spin at 900
rpm
2 kg
Spin
Rinse Hold
HANDWASH
30°-Cold
Special programme
for delicate fabrics
with «hand washing»
care symbol.
Main wash
Rinses
Max. final
spin at 900
rpm
2 kg
Spin
Rinse Hold
RINSES With this programme
it is possible to rinse
and spin cotton gar-
ments which have
been washed by
hand. The appliance
performs some rinses,
followed by a final
long spin. The spin
speed can be re-
duced.
Rinses
Max. final
spin at 1200
rpm
6 kg
Spin
Rinse Hold
Extra Rinse
DRAIN For emptying out the
water of the last rinse
in programmes with
the Rinse Hold option
selected.
Draining of
water
6 kg
SPIN Separate spin for
hand washed gar-
ments and after pro-
grammes with the
Rinse Hold option se-
lected. You can
choose the spin speed
by pressing the rele-
vant button to adapt it
to the fabrics to be
spun.
Max. final
spin at 1200
rpm
6 kg
Spin
1) If you select the SUPER QUICK option, we recommend you, to reduce the maximum load as indicated. (Red. load = reduced
load). Full loading is possible however with somewhat reduced cleaning results.
2) If using liquid detergents, a programme without PREWASH must be selected.
ENGLISH 14
Consumption values
Programme Energy consumption
(KWh)
Water consumption
(litres)
Programme duration
(Minutes)
1)
White Cottons 90° 2 61 140
Cottons 60° 1.3 58 125
Cottons ECONOMY
60°
2)
1.02 45 155
Cottons 40° 0.75 58 120
Synthetics 40° 0.5 47 80
Delicates 40° 0.55 58 70
Wool 40° 0.45 55 60
Handwash 30° 0.3 58 55
1) Without prewash option selected.
2) «Cottons Economy» at 60°C with a load of 6 kg is the reference programme for the data entered in the energy label, in
compliance with CEI 456 standards.
The consumption data shown on this chart is to be considered purely indicative, as it may
vary depending on the quantity and type of laundry, on the inlet water temperature and
on the ambient temperature.
Care and cleaning
Warning! Switch the appliance off before
you carry out any cleaning or
maintenance work.
Maintenance Wash
With the use of low temperature washes it is
possible to get a build up of residues inside the
drum.
We recommend that a maintenance wash be
performed on a regular basis.
To run a maintenance wash:
The drum should be empty of laundry.
Select the hottest cotton wash programme.
Use a normal measure of detergent, must be
a powder with biological properties.
Cleaning the dispenser drawer and the
drawer recess
1
To remove the draw-
er, press the catch
downwards and pull
it out.
2
To aid cleaning, re-
move also the top
part of the additive
compartment.
ENGLISH 15
3 Use a stiff brush to
clean and remove all
washing powder res-
idue.
4
Flush out all the re-
moved parts of the
dispenser drawer
under a tap to re-
move any traces of
accumulated pow-
der.
5
Use the previous
brush to clean the re-
cess, ensuring that
upper and lower part
of it is well cleaned.
After having cleaned
the dispenser and
the drawer recess,
replace it and run a
rinse programme
without any laundry
in the drum to flush
away any residue.
Cleaning the pump
Proceed as follows:
1
A
B
Place a container
close to the pump (A),
to collect any spill-
age.
2
Pull out the emergen-
cy emptying hose (B),
place it in the con-
tainer and remove its
cover cap.
3
When no more water
comes out, unscrew
the pump cover (A)
and remove it. Al-
ways keep a rag
nearby to dry up
spillage of water
when removing the
pump.
4
Remove any objects
from the pump impel-
ler by rotating it.
5
Use a pencil to check
whether the pump
wheel right at the
back of the pump
housing can turn. (It is
normal for the pump-
ing wheel to turn
jerkily.) If the pump-
ing wheel cannot be
turned, please con-
tact the After Sales
Service.
ENGLISH 16
6 Put the cap back on
the emergency emp-
tying hose and place
the latter back in its
seat. Screw the pump
fully in.
Cleaning the water inlet filters
If the appliance takes long to fill with water or
doesn't fill, the starting button indicator light
blinks in red. Check if the water inlet filters are
blocked (see chapter "What to do if..." for
more details).
Proceed as follows:
1
Turn off the water
tap.
Unscrew the hose
from the tap.
Clean the filter in
the hose with a stiff
brush.
Screw firmly the in-
let hose back onto
the tap.
2
Unscrew the hose from the appliance.
Keep a rag nearby because some water
may flow.
Clean the filter in the valve with a stiff
brush or with the piece of cloth.
3
35°
45°
•Screw the hose
back to the appli-
ance turning it to
the left or the right
to suit the installa-
tion. Tight the lock-
nut correctly to
prevent water
leaks.
Turn on the water
tap.
The dangers of freezing
If the appliance is exposed to temperatures
below 0°C, certain precautions should be tak-
en.
Turn off the water tap.
Unscrew the inlet hose.
Place the end of the emergency emptying
hose and that of the inlet hose in a bowl
placed on the floor and let water drain out.
Screw the water inlet hose back on and re-
position the emergency emptying hose after
having put the cap on again.
When you intend to start the appliance up
again, make sure that the room temperature
is above 0°C.
Important! Every time you drain the water
through the emergency emptying hose you
must pour 2 litres of water into the main wash
compartment of the detergent drawer and
then run the drain programme. This will
activate the ECO VALVE device avoiding that
part of the detergent remains unused at next
washing.
Emergency emptying out
If the water is not discharged, proceed as fol-
lows to empty out the appliance:
pull out the plug from the power socket;
close the water tap;
if necessary, wait until the water has cooled
down;
open the pump door;
ENGLISH 17
place a bowl on the floor and place the end
of the emergency emptying hose into the
bowl. Remove its cap. The water should
drain by gravity into the bowl. When the
bowl is full, put the cap back on the hose.
Empty the bowl. Repeat the procedure until
water stops flowing out;
clean the pump if necessary as previously
described;
replace the emergency emptying hose in its
seat after having plugged it;
screw the pump cover again and close the
door.
What to do if…
The appliance does not start or stops during
operation. It is possible that the red indicator
light of button 5 blinks to indicate that the ap-
pliance is not working.
Before contacting your local Service Centre,
please carry out the checks listed below.
Problem Possible cause Solution
The appliance
does not start:
The door has not been closed (The
red indicator light of button 5 blinks).
Close the door firmly.
The plug is not properly inserted in
the power socket.
Insert the plug into the power socket.
There is no power at the socket. Please check your domestic electrical
installation.
The main fuse has blown. Replace the fuse.
The programme selector dial is not
correctly positioned and the button 5
has not been pressed.
Please turn the selector dial and
press the button 5 again.
The delay start has been selected. If the laundry are to be washed im-
mediately, cancel the delay start.
The appliance
does not fill:
The water tap is closed The red indi-
cator light of button 5 blinks).
Open the water tap.
The inlet hose is squashed or kinked
(The red indicator light of button 5
blinks).
Check the inlet hose connection.
The filter in the inlet hose or the inlet
valve filter are blocked (The red in-
dicator light of button 5 blinks).
Clean the water inlet filters. (See
"Cleaning the water inlet filters" for
more details).
The door is not properly closed (The
red indicator light of button 5 blinks).
Close the door firmly.
The appliance
does not empty:
The drain hose is squashed or kinked
(The red indicator light of button 5
blinks).
Check the drain hose connection.
The drain filter is clogged (The red
indicator light of button 5 blinks).
Clean the drain filter.
ENGLISH 18
Problem Possible cause Solution
An option or a programme that ends
with the water still in the tub or a that
eliminates all the spinning phases
has been selected.
Select the draining or spinning pro-
gramme.
The appliance
spinning phase
starts late or
does not start:
The electronic unbalance detection
device has cut in because the laundry
is not evenly distributed in the drum.
The laundry is redistributed by re-
verse rotation of the drum. This may
happen several times before the un-
balance disappears and normal
spinning can resume. If, after 10 mi-
nutes, the laundry is still not evenly
distributed in the drum, the appli-
ance will not spin.
Redistribute the load manually or
load more laundry and select the
spin programme.
There is water
on the floor:
Too much detergent or unsuitable
detergent (creates too much foam)
has been used.
Reduce the detergent quantity or use
another one.
Check whether there are any leaks
from one of the inlet hose fittings. It is
not always easy to see this as the
water runs down the hose; check to
see if it is damp.
Check the water inlet hose connec-
tion.
The drain or inlet hose is damaged. Replace it with a new one (check with
the After Sales Service the right spare
part number).
The cap on the emergency emptying
hose has not been replaced or the
filter has not been properly screwed
in after cleaning action.
Refit the cap on the emergency emp-
tying hose or screw the filter fully in.
The door will not
open:
The programme is still running. Wait the end of washing cycle.
The door lock has not been released. Wait a few minutes before opening
the door.
There is water in the drum. Select drain or spin programme to
empty out the water.
The appliance
produces an un-
usual noise
The transit bolts and packing have
not been removed.
Check the correct installation of the
appliance.
The support feet have not been ad-
justed
Check the correct levelling of the ap-
pliance.
The drain pump could be blocked. Check the drain pump. (See "Clean-
ing the pump" for more details).
ENGLISH 19
Problem Possible cause Solution
Unsatisfactory
washing results:
Too little detergent or unsuitable de-
tergent has been used.
Increase the detergent quantity or
use another one.
Stubborn stains have not been trea-
ted prior to washing.
Use commercial products to treat the
stubborn stains.
The correct temperature was not se-
lected.
Check if you have selected the cor-
rect temperature.
Excessive laundry load. Reduce the laundry load in accord-
ing to the "Washing Programmes ta-
ble".
After the check, switch on the appliance and
press the button 5 to restart the programme.
If the malfunction shows again, contact your
After Sales Service.
The necessary data for the service centre is on
the rating plate. We recommend that you write
the data here:
Model description (MOD): .....................
21552
© Inter IKEA Systems B.V. 1999
Made In Italy
501.514.59
Product number (PNC): ...........................
Serial number (S.N.): ...............................
Technical data
Dimensions Width (cm) 59,6
Height (cm) 82
Depth (cm) 54
Water supply pressure
1)
Minimum
Maximum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Cotton max. load (kg) 6
Max. spin speed (rpm) 1200
Energy class A+
Washing class A
Spinning class B
Washing noise (dB(A)) 54
Spinning noise (db(A)) 76
ENGLISH 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104

IKEA RIWM60 Manuel utilisateur

Catégorie
Machines à laver
Taper
Manuel utilisateur

dans d''autres langues