Tetra Contour Flex Guide d'installation

Marque: Tetra

Modèle: Contour Flex

Taper: Guide d'installation

Installation Guide

SIGN299 | DOC-2001572

2424

Volt

Save These Instructions

Use only in the manner intended by the manufacturer.

If you have any questions, contact the manufacturer.

For the latest North American install guides for your product go to: https://products.LED.com/led-signage-lighting

For the latest European install guides for your product go to: https://products.LED.com/eu/led-signage-lighting

RETROFIT SIGN CONVERSION LED KIT FOR USE ONLY

IN ACCORDANCE WITH KIT INSTRUCTIONS.

KIT IS COMPLETE ONLY WHEN ALL PARTS REQUIRED

BY THE INSTRUCTIONS ARE PRESENT.

TROUSSE DE CONVERSION À DEL POUR LA

MODERNISATION DES ENSEIGNES

À UTILISER CONFORMÉMENT AU GUIDE D’INSTALLATION.

BG Българската версия на инструкциите за инсталаця и

информация за безопасност могат да бъдат намерени

на следния адрес: https://products.LED.com/eu/led-

signage-lighting

CS Návod k montáží a bezpečnostní informace v češtině

najdete zde: https://products.LED.com/eu/led-signage-

lighting

DA Den danske version af installationsvejledningen og

sikkerhedsoplysninger kan findes på følgende placering:

https://products.LED.com/eu/led-signage-lighting

DE Die deutsche Version der Installationsanleitung und

Sicherheitsinformationen finden Sie in folgendem Verzeic:

https://products.LED.com/eu/led-signage-lighting

EL Μπορείτε να βρείτε την ελληνική εκδχή των οδηγιών

νγκατάστασης και των πληροφοριών ασφάλειας στην

εξής τοποθεσία: https://products.LED.com/eu/led-

signage-lighting

ES La versión española de las instrucciones de instalación y

la información sobre seguridad puede encontrarse en la

siguiente ubicación: https://products.LED.com/eu/led-

signage-lighting

ET Eestikeelse paigaldusjuhendi ja ohutusnñuded leiate

aadressilt: https://products.LED.com/eu/led-signage-

lighting

FI Asennusohjeiden ja turvallisuustietojen suomenkielinen

versio löytyy seuraavasta paikasta: https://products.LED.

com/eu/led-signage-lighting

FR La version française des instructions d’installations et

information de sécurité est disponible à l’adresse suivante:

https://products.LED.com/eu/led-signage-lighting

HR Hrvatska verzija priručnika za ugradnju i sigurnosnih

informacija nalazi se na sljedečoj lokaciji: https://products.

LED.com/eu/led-signage-lighting

HU A telepítési útmutató és a biztnosági információk magyar

nyelvű változata az alábbi címen található: https://

products.LED.com/eu/led-signage-lighting

IT La versione italiana del manuale di installazione e

sicurezza può essere reperita nella seguente sezione:

https://products.LED.com/eu/led-signage-lighting

LT Lietuvišką diegimo instrukcijos ir saugos informacijos

versiją galima rasti šioje vietoje: https://products.LED.

com/eu/led-signage-lighting

LV Uzstādīšanas instrukciju un drošības informāciju latviešu

valodā var atrast šeit: https://products.LED.com/eu/led-

signage-lighting

NL De Nederlandse versie van de installatie-instructies en

veiligheidsinformatie kan op de volgende locatie worden

gevonden: https://products.LED.com/eu/led-signage-

lighting

PL Polską wersję instrukcji instalacji oraz informacje

dotyczące bezpieczeństwa można znaleźć w następującej

lokalizacji: https://products.LED.com/eu/led-signage-

lighting

PT A versão em Português das instruções de instalação e

das informações de segurança pode ser encontrada na

seguinte localização: https://products.LED.com/eu/led-

signage-lighting

RO Versiunea în limba română a instrucţiunilor de instalare

şi a informaţiilor de siguranţă pot fi găsite la: https://

products.LED.com/eu/led-signage-lighting

SV Ni hittar den svenska versionen av

installationsanvisningarna och säkerhetsinformationen på

följande plats: https://products.LED.com/eu/led-signage-

lighting

SL Previdnostna opozorila in varnostne informacije so na

zadnji strani vodnika za namestitev. Pred začetkom

namestitve izdelka jih skrbno preberite: https://products.

LED.com/eu/led-signage-lighting

SK Slovenskú verziu montažnej príručky a bezpečnostnŷch

instrukcií nájdete na nasledujúcej lokalite: https://

products.LED.com/eu/led-signage-lighting

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Prepare Electrical Wiring

Electrical Requirements

• Acceptable to use in dry, damp, and wet locations when installed

correctly.

• The grounding and bonding of the LED Driver shall be done in

accordance with National Electric Code (NEC) Article 600.

• Follow all National Electric Codes (NEC) and local codes.

• These products are only suitable for connection to a circuit from

a Class 2 power source. These products have not been evaluated

for use when connected to a power source that does not comply

with Class 2 voltage and energy limited supplies.

FOR UL ONLY

Contour Gen 2 Flex

LED Lighting System

Side Bend

GEXNFS32-1, GEXNFS65-1, GEXNFSRD-1,

GEXNFSGL-1, GEXNFSBL-1, GEXNFSYG-1,

GEXNFSRC-1

Contour Gen 2 Flex (Side Bend) Installation Guide

WARNING / AVERTISSEMENT

RISK OF ELECTRIC SHOCK

• Turn power off before inspection, installation or removal.

• Properly ground power supply enclosure.

• Not to be submerged or used in a marine environment.

RISK OF FIRE

• Use only suitably approved wire for input/output

connections. Minimum size 18 AWG (0.82mm2)

• Follow all local codes.

• Waterproof wire connection for outdoor or wet

installations. See instructions for details.

• Do not stretch light engines.

• Inspect and replace the light engines if any tear or

damage affects their integrity.

• Avoid installation that leads to prolonged exposure to

standing water or ice.

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l’alimentation avant l’inspection, l’installation ou le déplacement.

• Assurez-vous de correctement mettre à terre l’alimentation électrique.

• Ne pas submerger ou installer dans un environnement marin

RISQUES D’INCENDIE

• N’utilisez que des fils approuvés par UL pour les entrées/sorties de

connexion. Taille minimum 18 AWG (0.82mm2)

• Respectez tous les codes locaux.

• Étanchéifier les connexions électriques effectuées à l’extérieur

ou pour un environnement exposé à l’eau. Voir les instructions

d’installation pour plus de détails.

• Ne pas étirer les modules DEL Contour.

• Inspecter l’intégrité des modules DEL Contour et les remplacer s’ils

sont déchirés ou endommagés.

• Éviter les installations avec une exposition prolongée à l’eau

stagnante ou à la glace.

UL WARNING / AVERTISSEMENT UL

RISK OF FIRE OR ELECTRIC SHOCK

• LED Retrofit Kit installation requires knowledge of

sign electrical systems. If not qualified, do not attempt

installation. Contact a qualified electrician.

• Install this kit only in host signs that have been

identified in the installation instructions and where the

input rating of the retrofit kit does not exceed the input

rating of the sign.

• Installation of this LED retrofit kit may involve drilling or

punching of holes into the structure of the sign. Check

for enclosed wiring andcomponents to avoid damage to

wiring and electrical parts.

• Do not make or alter any open holes in an enclosure of

wiring or electrical components during kit installation.

RISQUE D’INCENDIE OU DE CHOC ÉLECTRIQUE

• L’installation de l’équipement de remplacement DEL exige Ia

connaissance des systèmes électriques pour enseignes. Si non qualifié, ne

tentez pas d’installation. Veuillez contacter un électricien qualifié.

• Risque d’incendie ou de choc électrique. Installez cet ensemble seulement

dans des enseignes hôtes qui ont été identifiés dans les instructions

d’installation et dont la capacité d’entrée de l’ensemble ne dépasse pas la

capacité d’entrée de l’enseigne.

• L’installation de cet équipement de remplacement DEL peut impliquer le

perçage ou le poinçonnage de trous dans la structure du panneau Vérifiez

le câblage et les composants inclus pour éviter d’endommager le câblage

et les composants électriques.

• Ne pas faire ou modifier les trous ouverts dans une enceinte de câblage

ou de composants électriques pendant l’installation de cet équipement

de remplacement DEL.

CAUTION / ATTENTION

RISK OF INJURY

• While performing installations described, gloves, safety

glasses or goggles should be worn.

RISQUE DE BLESSURE

• Lors de l’exécution des installations décrites, des gants, des lunettes de

sécurité ou des lunettes de protection doivent être portées.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

This Class [A] RFLD complies with the Canadian standard ICES-005. Ce DEFR de la classe [A] est conforme à la NMB-005 du Canada.

Contour Gen 2 Flex (Side Bend) Installation Guide

Components and Tools Required

3 4 5 6 7 8 9 10

Contour Gen 2 Flex Side Bend Light Engine

GEXNFRL-1 Flex Rail or GEDSRLXX-3 Tetra SNAP Rail

GEXNFMC-1 Flex Mounting Clip

#6, #8 or #10 (M2, M3 or M4) self-drilling pan headed screws

#6 (M2) screws

Minimum 22 AWG (0.33mm2) tie-wire

24 Volt power supply

UL approved 18 AWG (0.82mm2) supply wire

UL approved 22-14 AWG (0.33-2.08mm2) twist-on wire connectors

GEXNFEC-1 Flex End Cap

Electrical grade silicone.

Examples of electrical grade silicone:

• Momentive RTV 6702 (white) / RTV 6708 (clear) - Silicone Rubber Adhesive Sealant

• Momentive RTV 162 (White) - Silicone Rubber Adhesive Sealant-Electrical Grade

• Dow Corning 3140 (clear) - Non-Corrosive Flowable

• Dow Corning 3145 (clear or gray) - Non-Corrosive Non-flowable

• Dow Corning RTV 748 (white) - Non-Corrosive Sealant

Cutting Resolution Table

Light Engine Color Cutting Resolution

Red, Red-Orange,

Amber,Green, Blue, White 4 in. (101.6 mm)

Weather box GEXNWB2

Contour Light Guide connector

Contour Light Guide 90° inside corner

Contour Light Guide 90° outside corner

Contour Light Guide 90° planar corner

Optional / Required for Wet Locations

Optional

11 16

12 13 14 15

100” (2.54 m) 95.4” (2.42 m)

Contour Gen 2 Flex (Side Bend) Installation Guide

4.5 in. (114 mm)

Mount the Flex rails so that

they are gapped at least

4.5 in. (114 mm) apart if end

to end, using a #6 or #8

(M2 or M3) screw at least

every 2 ft. of rail but not less

than 2 screws per rail.

NOTE: For an 8 ft. rail

length, there will be 2.08 in.

(52.8 mm) of excess light

engine on each end.

Using the Flex Rail final length,

measure out the necessary

length of Contour LED light

engine so that it will extend

at least 3/4 in. (19 mm). If

required, use a sharp cutting

tool to cut through light engine

(refer to the Cutting Resolution

Table on page 2).

Installation

Plan the layout by measuring the design

layout and dividing by 8 ft . (2.44m)

to determine the required quantity of

Contour Gen 2 Flex. Refer to the Cutting

Resolution Table on page 3 when

cutting any Contour Gen 2 Flex section.

Do not use more than one suffix

code for each respective application,

as mixing suffix codes may result in

appearance variation. Suffix code can

be found on the packaging label.

NOTE: If mounting surfaces are rough or uneven, take the necessary precautions to avoid bending the rail when

mounting.

If you have any questions about these instructions or your specific Contour application, please contact support at

[email protected]

Planning First

METHOD A - Installing Light Engines With GEXNFRL-1 Flex Rail

- Straight Runs Only

1 2 For cut end, fill cap with

electrical grade silicone and

push cap on the end to seal.

Clean excess silicone.

Electrical grade

silicone

Cut on marks only

Contour Gen 2 Flex (Side Bend) Installation Guide

Cut end

at top

Uncut

end at

bottom Fill end cap with

silicone and install

Insert wire connectors into

weather box. Fill with electrical

grade silicone and close box.

Weather box can be mounted

using #8 (M3) screws.

Weather box

can be painted

To connect two light engines,

first strip wire ends back

0.5 in. (13mm). Then join wires

together using twist-on wire

connectors.

WARNING / AVERTISSEMENT

RISK OF FIRE: Waterproof wire connection and all cut ends for outdoor or wet installations. Weather box is required for all outdoor

or wet locations electrical connections.

RISQUE D’INCENDIE: Étanchéifier les connexions électriques et sceller l’extrémité des sections coupées effectuées à l’extérieur ou

pour un environnement exposé à l’eau. Un boitier étanche est requis pour les connexions électriques effectuées à l’extérieur ou

dans un environnement avec exposition à l’eau.

6 7

For vertical or near vertical

installations, any cut-end

termination of a Contour

piece shall reside at the

top of the design.

WARNING/AVERTISSEMENT

RISK OF FIRE: The light engine is not intended for excessive or repetitive bending or

stretching. If the silicone does crack, replace the light engine.

RISQUE D’INCENDIE: Les modules DEL Contour ne sont pas conçus pour des pliages

excessifs, répétitifs ou pour être étirés. Si le silicone montre des signes de craquement,

remplacer le module DEL Contour.

–

Push the light engine segments

down into the Flex Rail.

Electrical grade

silicone

Electrical

grade

silicone

Linear: At each gap

between sections, apply

silicone on both sides

to secure light guide

connector. Snap on a light

guide connector.

Corner: For all corners (planar,

inside, outside) apply silicone

on both sides to secure light

guide corners. Snap on corner.

Follow Steps 8-9 if wires are cut.

Joining with Light Guide Connectors, Corners and Bends

Do not

bend one

light into a

corner

8 9

Contour Gen 2 Flex (Side Bend) Installation Guide

6-12 in.

(152-305 mm)

Plan the layout by measuring the design

layout and dividing by 8 ft . (2.44 m)

to determine the required quantity

of Contour Gen 2 Flex. Refer to the

Cutting Resolution Table on page 3

when cutting any Contour Gen 2 Flex

section.

Do not use more than one suffix

code for each respective application,

as mixing suffix codes may result in

appearance variation. Suffix code can

be found on the packaging label.

DO NOT bend the light engine to an inside radius that is tighter than 1 in. (25.4 mm).

If you have questions about these instructions or your Contour application,

contact support at [email protected]

Planning First

METHOD B - Installing Light Engines With GEXNFMC-1 Flex Mounting Clip

Install a Flex Mounting Clip,

using #6 (M2) counter sink

screws, every 6-12 inches

(152-305 mm) on center until

the end of the run is reached.

Installation

Using the light engine final

length, measure out the

necessary length of Contour

light engine so that it will

extend at least 3/4 in. (19 mm)

past the last mounting clip. If

required, use a sharp cutting

tool to cut through light engine.

For cut end, fill cap with

electrical grade silicone and

push end cap on the end to

seal. Clean excess silicone.

1 2 3

WARNING / AVERTISSEMENT

RISK OF FIRE: DO NOT bend the light engine to an inside radius that is tighter than 1 in. (25.4 mm).

RISQUE D’INCENDIE: Ne pas plier les modules DEL Contour avec un rayon de courbure inférieur à 1 pouce (25.4 mm).

Back bendSide bend

Cut on marks only Electrical grade

silicone

Contour Gen 2 Flex (Side Bend) Installation Guide

Push into clips

Insert wire connectors

into weather box. Fill with

electrical grade silicone and

close box.

Secure the weather box using

a #6 or #8 (M2 or M3) screw.

Power

supply

Red (+)

Black or blue (–)

To Contour

Strip wires back 0.5 in. (13mm).

Connect the red wire (+)

from the LED strip to the red

wire (+) of the power supply.

Connect the black wire (-)

from the LED strip to the black

or blue wire (-) of the power

supply.Grounding and bonding

must be done in accordance

with National Electrical Code

(Article 600). See power supply

instructions.

Run a wire from the power

supply to a section of Contour.

Power supply connection

to the AC mains must be

completed in an acceptable

enclosure. Power supply

loading is described on

page 9.

Connect Power Supply

WARNING/AVERTISSEMENT

RISK OF ELECTRICAL SHOCK: Turn power OFF before inspection, installation or removal.

RISQUES DE CHOC ÉLECTRIQUE: Coupez l’alimentation électrique avant d’inspecter, d’installer ou de déplacer le luminaire.

910

To power supply

Red (+)

Black or

blue (–)

Weather box can be painted

Push each light

engine segment

into the clips.

4Insert wire connectors

into weather box. Fill

with electrical grade

silicone and close

box. Weather box can

be mounted using #8

(M3) screws.

To connect two

light engines, first

strip wire ends back

0.5 in. (13mm). Then

join wires together

using twist-on wire

connectors.

Secure light engine

by twisting tie-wire

around the mounting

clip and light engine.

65 7

Weather

box can be

painted

–

Contour Gen 2 Flex (Side Bend) Installation Guide

1. (Existing Signs Only) Prior to installation, survey the site for information regarding power and accessibility inside

and outside the building. Ensure that the branch circuit supplying the existing transformer or ballast will be within

the voltage ratings of the new LED power supply, and have a current rating not exceeding 20A, or that permitted by

applicable local, state, or country electrical codes (whichever is less).

2. (Existing Signs Only) Remove the existing lighting equipment to be replaced, such as neon tubing or fluorescent

tubes; and associated transformers and ballasts. Care should be taken not to break the existing neon or fluorescent

tubes. NOTE: Follow all federal and local regulations when disposing of neon tubing, fluorescent tubes, transformers

and ballasts.

3. (Existing Signs Only) If removal of the existing lighting equipment eliminates the disconnect switch, as required by

applicable local, state, or country electrical codes; a new disconnect switch must be installed.

4. (Existing Signs Only) Repair and seal any unused openings in the electrical enclosure. Openings greater than 12.7-mm

(1/2-in) diameter require a metal patch secured by screws or rivets and caulked with non-hardening caulk. Smaller

openings may be sealed with non-hardening caulk.

5. Using the layout guidelines above, determine required number of LED modules required to illuminate the sign.

6. A 24VDC Class 2 Power Supply, as listed below, must be used with this retrofit kit. Determine the number of Power

Supplies required to power the number of LED modules required to illuminate the sign, so as not to overload the Power

Supply chosen.

7. Follow Method A, B or C to mount the Contour Gen 2 Flex.

8. Connect the DC output of the power supply to the LED modules using the Electrical Connections instructions above.

9. Connect the power unit to the supply in accordance with the applicable local, state, and country electrical codes, and

the instructions found in the power supply installation guide.

10. If required, the disconnect switch shall be installed by qualified personnel, in accordance with applicable local, state,

and country electrical codes.

Retrofit Instructions

Troubleshooting

Symptom Condition Solution

All LEDs are OFF

No AC input. Attach AC input and/or check circuit breaker.

Incorrect wire attachment.

Check wire connection(s) at the Contour Gen 2 Flex LED light

engine and power supply for improper connections or short

circuits. Make sure you have positive to positive and negative to

negative wire connections.

Some LEDs

appear dim

Overload (maximum load exceeded).

Ensure the overall length of Contour LED Gen 2 Flex light engine

does not exceed the maximum load as detailed in the Tetra

Power Supply Installation Instructions.

Maximum recommended supply wire

length exceeded.

Reduce the length of supply wire equal to or below the

recommended maximum.

Mixed Suffix Codes of LED light

engine within an application.

Make sure that all LED light engines have the same Suffix Code

(Suffix Code is located on each packaging label).

Some of the

sections are not

illuminated

Incorrect wire attachment.

Check the wire connections at the Contour Gen 2 Flex LED light

engine for improper connections. Make sure you have positive

to positive and negative to negative wire connections. Check for

improper cutting resolution locations (see table on Page 2).

Light/dark banding

along a section

LED light engine flexed in the wrong

direction or smaller than the minimum

bend radius during installation.

Remove LED light engine and properly install.

Inspect and replace light engine if damaged.

Contour Gen 2 Flex (Side Bend) Installation Guide

NOTE: For linear long runs, center connection to the LED strip is recommended to minimize voltage drop.

*GELP24-60U-GL minimum load = 15 ft. (4.57 m).

**GEPS24V50-100W minimum load = 36 ft. (10.97 m).

Maximum Loading per 24 VDC Class 2 Power Supply

Power Supply

GEXNFS32-1, GEXNFS65-1, GEXNFSRD-1, GEXNFSGL-1,

GEXNFSBL-1, GEXNFSYG-1, GEXNFSRC-1

Rating per module 24VDC, 1.4W/ft. (Strip)

GEPS24-25U-NA, GEPS24-25-EU (CE only)

Load shall not exceed 0.83A 15ft. (4.57 m)

GEPS24D-60U-GLX, *GELP24-60U-GL

Load shall not exceed 2.5A 39 ft. (11.88 m)

GEPS24D-80U

Load shall not exceed 3.3A 49ft. (14.93 m)

GEPS24-100U-GLX, GEPS24D-100U-NA, GEPS24LT-100U-NA,

USVI-100024FE, USVI-100024FBA

Load shall not exceed 4.0A

59ft. (17.98 m)

GEPS24-100U-GLX2, GEPS24-100U-TT, **GEPS24V50-100W

Load shall not exceed 4.0A 62ft. (18.89 m)

GEPS24-200U-GLX2

Load shall not exceed 4.0A per each (of 2) output channels

62ft. (18.89 m) per bank

124 ft. (37.78 m) per PS

GEPS24-300U-GLX2

Load shall not exceed 4.0A per each (of 3) output channels

62ft. (18.89 m) per bank

186 ft. (56.67 m) per PS

This product is intended solely for the use of non-residential signage lighting and is not intended for use in any other applications.

Conforms to the following standards:

Dismantling

At the end of life, the contained LED light source may be cut out using suitable wire cutters, removed from the mounting surface,

then replaced per the cutting and installation instructions above, or dismantled and taken to a communal collecting point for

environmentally friendly disposal in accordance with local regulations by a professional installer.

Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly

disposal in accordance with local regulations. Contact your local authorities or stockist for advice on recycling. The packaging material is recyclable.

Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection-service.

Power Supply

Wattage

18 AWG/0.82 mm2

Supply Wire

16 AWG/1.31 mm2

Supply Wire

14 AWG/2.08 mm2

Supply Wire

12 AWG/3.31 mm2

Supply Wire

25W 20 ft./6.1 m –––