Technology at Work.®
www.janam.com
Quick Start Guide
XM75+ Series™
XM75+ Series Quick Start Guide
Page 2
Janam Technologies LLC
XM75+ Series Quick Start Guide
Copyright 2021 Janam Technologies LLC. All rights reserved.
XM75+ Series, Janam and the Janam logo are trademarks of Janam Technologies LLC. Other product and brand
names may be trademarks or registered trademarks of their respective owners.
Janam Technologies LLC assumes no responsibility for any damage or loss resulting from the use of this guide.
Janam Technologies LLC assumes no responsibility for any loss or claims by third parties which may arise through
the use of this product. Janam Technologies LLC assumes no responsibility for any damage or loss caused by
deletion of data as a result of malfunction, dead battery or repairs. To protect against data loss, be sure to make
backup copies (on other media) of all important data.
Follow all usage, charging and maintenance guidelines in the Product User Guide. If you have questions, contact
Janam. For a copy of the Product User Guide, visit www.janam.com.
XM75+ Series Quick Start Guide
Page 3
Janam Technologies LLC
Content and Additional Resources
To help you get started with your XM75+ Series mobile computer, this guide features:
-Hardware Overview
-Getting Started
A. Install the Battery
B. Remove the Battery
C. Install SIM & SD Card
D. Charge the Battery
-Battery Warning
-Regulatory
Contents of this guide are subject to change.
For software updates and information, visit www.janam.com.
XM75+ Series Quick Start Guide
Page 4
Janam Technologies LLC
Hardware Overview
1. Speaker
2. LED indicator & Sensor
3. Touchscreen
4. Software buttons
5. USB Type C connector
6. I/O connector
7. Keypad
8. Scan button (Left)
9. Volume buttons
5
9
3
4
2
1
8
76
XM75+ Series Quick Start Guide
Page 5
Janam Technologies LLC
Hardware Overview
10. Rear camera & Flashlight
11. Battery cover
12. Battery cover release button
13. Hand strap mount
14. Speaker
15. Scan button (Right)
16. Power button
17. Scanner
15
17
10
11
14
12 13
16
XM75+ Series Quick Start Guide
Page 6
Janam Technologies LLC
Getting Started
Important Note: The main (removable) battery charges the internal backup battery with or without an external
power source.
Caution: All user data will be lost if the main battery is removed before the internal backup battery is properly
charged. It is recommended you check that the backup battery capacity is at 100% prior to removing the main
battery. To do this, access Settings-> Battery. It is also recommended that you first suspend the device prior to
removing the main battery.
A. INSTALL THE BATTERY
1. Press the battery release button and gently lift up the cover.
2. Align the connector (gold contact) of the battery with the battery connector of device.
3. Insert top of the battery first and then snap in place.
Caution: Don’t slide the battery over the battery connector of the device while inserting the battery. It
may damage the connector pin.
4. Replace the battery cover by positioning the top first and sliding cover into place.
XM75+ Series Quick Start Guide
Page 7
Janam Technologies LLC
Getting Started
B. REMOVE THE BATTERY
1. Remove the back cover by pressing down on the “Push” button and lifting the cover up from both sides.
2. Push the battery towards the top of the compartment and lift from the bottom to remove.
C. Install SIM & MICROSD card
To install the SIM card:
1. Open the battery cover.
2. Slide the card into the slot with the contacts facing down.
3. To remove the card, gently slide the card out from the slot.
To install the microSD card:
1. Open the battery cover.
2. Lift the rubber on the bottom side of the slot.
3. Slide the card into the slot with the contacts facing down.
4. To remove the card, gently slide the card out from the slot.
[Inserting SIM card] [Inserting microSD card]
XM75+ Series Quick Start Guide
Page 8
Janam Technologies LLC
Getting Started
D. CHARGE THE BATTERY
To charge the battery using the USB Cable:
1. Connect the AC/DC adapter to the XM75+.
2. Plug in the AC/DC adapter. Use only easily accessible wall outlets that are easily reached with the length of supplied power
cable.
To charge the battery using a Cradle Kit:
1. Connect the power supply to the cradle, then connect the line cord to the power supply.
2. Plug in the power supply. Use only easily accessible wall sockets that are easily reached with the length of supplied power cable.
3. Place the device in the cradle. The LED on the device will illuminate to confirm connection.
4. The battery is fully charged in approx. 4 hours.
XM75+ Series Quick Start Guide
Page 9
Janam Technologies LLC
Battery Warning
BATTERY SAFETY GUIDELINES
Use only Janam XM75+ Series batteries and recharge batteries using only Janam approved charging accessories.
Observe the following guidelines for safe use of Li-ion batteries:
1. Do not expose the battery to excessive heat or cold. Do not short-circuit. Do not incinerate.
2. To avoid risk of fire, burn or damage to your battery, do not allow a metal object to touch battery contacts.
3. Do not disassemble the battery. There are no user serviceable parts inside.
4. If battery leakage is observed, avoid any contact with affected area and properly dispose of the battery.
5. If you come in contact with battery leakage, rinse exposed area with soap and water. If it contacts the eye,
flush the eye with water for 15 minutes and seek medical attention.
6. Dispose of used battery promptly. Keep away from children. Do not disassemble or dispose of in fire.
7. When discarding a battery, contact your local waste disposal provider to understand local restrictions for
disposal or recycling of batteries.
BATTERY CHARGER SAFETY GUIDELINES
1. Do not use the equipment in or near areas in which sparks are likely or possible.
2. Do not let equipment’s metal contacts and electrical sockets come in contact with metal objects.
3. For indoor use only. Do not expose the equipment to rain or any liquids.
4. Do not use or store the equipment in direct sunlight or in areas that are prone to get hot such as in a parked
vehicle, near a heat duct or close to other heat sources.
5. Keep equipment’s metal contacts and electrical sockets free from debris that could obstruct charging or could
cause a short circuit.
CAUTION
IF MISUSED OR MISTREATED THE BATTERY MAY PRESENT A RISK OF FIRE OR CHEMICAL BURN.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
XM75+ Series Quick Start Guide
Page 10
Janam Technologies LLC
Regulatory
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
Body-worn Operation
This device was tested for typical bodyworn operations with the Front & back of the device
kept 0.39 inches (1cm) between the user’s body and the Front & back of the device. To
comply with FCC RF exposure requirements, a minimum separation distance of 0.39 inches
(1cm) must be maintained between the user’s body and the Front & back of the device. Any
beltclips, holsters, and similar accessories containing metallic components may not be used.
Body-worn accessories that cannot maintain 0.39 inches (1cm) separation distance between
the user’s body and the Front & back of the device, and have not been tested for typical
body-worn operations may not comply with FCC RF exposure limits and should be avoided.
XM75+ Series Quick Start Guide
Page 11
Janam Technologies LLC
Regulatory
IC Warning
This device complies with Industry Canada license-exempt RSS standard(s).Operation is subject to the following
two conditions: (1) This device may not cause interference; and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisee aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si lebrouillage est susceptible d’en
compromettre le fonctionnement.
This device is restricted to indoor use only within the 5.15 ~ 5.35GHz Band.
Cet appareil est restreint a l’utilisation a l’interieur seulement dans la bande 5.15 ~ 5.35GHz.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless
authorized to do so by the FCC/IC.
Cet equipement est conforme aux limites d’exposition aux radiations FCC / IC definies pour un environnement non
controle. Cet emetteur ne doit pas etre colocalise ou fonctionner en conjonction avec une autre antenne ou un
autre emetteur, a moins d’etre autorise a le faire par le FCC / IC.
E-label
Users can access the product certificate information in Settings -> About phone -> Certificates.
WCDMA/LTE feature is optional. Some product options only include WLAN feature.
FCC ID : UTWXM75P
IC : 6914A-XM75P
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
