Standard Roll Toilet Paper Dispenser
4 Roll Vertical Faceplate Replacement Guide
Faceplate*
Plaque frontale*
Cover
Couvercle
4. To unlock the dispenser, insert key into lock and
rotate the key a quarter turn. Gently pull the cover
forward. The key may be removed at this point. The
cover will automatically open, do not force.
Pour déverrouiller le distributeur, insérer la clé dans le
verrou et faire tourner d’un quart de tour. Tirer doucement
le couvercle vers l’avant. Retire la clé. Le couvercle s’ouvrira
automatiquement, ne pas forcer.
1. Open the dispenser lid then position sliding door to
left side of dispenser opening. Align 3 teeth of bottom
sliding door to 3 notches on sliding track. Gently
support sliding door with your hand while using flat
screw driver to lift and pry each tooth one at a time to
disengage door from sliding track.
1.
Face Plate RemovalFaceplate Replacement Remplacement de la plaque frontale
2. Rotate bottom of sliding door inwards.
3.
5.
3. Pull entire sliding door up vertically to disengage
top of door from upper sliding track. Door is now
completely separated from cover.
2.
4.
Unlock
5. Locate the locking features on the faceplate on the
inside cover. Release the faceplate by lifting on the
release lever (red) and pushing up on the push tab
(blue). Brace the underside of the faceplate.
Repérer les points de verrouillage de la plaque frontale à
l’intérieur du couvercle. Dégager la plaque frontale en soulevant
le levier de dégagement (rouge) et en appuyant sur la languette
poussoir (bleue). Prendre la plaque frontale par le dessous.
6. After the faceplate is released, remove it by taking
it out from under the cover. Make sure to brace the
underside of the faceplate so it doesn’t fall to the floor
once released.
Après avoir dégagé la plaque frontale, l’enlever en la tirant
sous le couvercle. Veiller à maintenir le dessous de la plaque
frontale pour qu’elle ne tombe pas par terre une fois dégagée.
7. Close the cover completely and make sure it locks
shut.
Bien refermer le couvercle en s’assurant qu’il
est verrouillé.
8. Align the locking features on the new faceplate (red)
to the corresponding slots on the dispenser front
face (blue). Push the new faceplate up against the
dispenser and slide it up to slot it into the locking
features.
Alignez les points de verrouillage sur la nouvelle plaque
frontale (rouge) sur les encoches correspondantes de la
face avant du distributeur (bleu). Appuyez la nouvelle plaque
frontale contre le distributeur et faites-la glisser pour l’insérer
dans les points de fixation.
Legal/ Juridique
®/™ Trademarks of Kimberly-Clark Worldwide, Inc. or its aliates. © KCWW
®/™ Marques de commerce de Kimberly-Clark Worldwide, Inc. ou de ses filiales. © KCWW
Parts made in Mexico and China, Assembled in Mexico / Pièces fabriquées au Mexique et en
Chine, et assemblées au Mexique / Partes hechas en México y China, armado en México / Telle
hergestellt in Mexiko und China, montiert in Mexiko / Peças produzidas no México e na China,
montagem no México / 部件在墨西哥和中国制造，在墨西哥组装
Distributed in the U.S. by Kimberly-Clark Global Sales, LLC, Roswell, GA 30076-2199
Distributed in Canada by Kimberly-Clark Inc., Mississauga, Ontario L5B 3Y5
Kimberly-Clark Europe Limited, Walton Oaks, Dorking Road, Tadworth, Surrey, KT20 7NS, UK
www.kcprofessional.co.uk +44 (0) 1737 736000
Kimberly-Clark B.V., Copernicuslaan 35, 6716 BM Ede, Netherlands
Distributed in Australia by Kimberly-Clark Australia Pty. Ltd, Level 4, 100 Arthur Street, North Sydney,
NSW 2060 Tel: 1800 647 994 www.kcprofessional.com.au
Distributed in New Zealand by Kimberly-Clark New Zealand, Level 2, 123 Carlton Gore Road, Newmarket,
Auckland 1023, New Zealand Tel: 0800 447 814 www.kcprofessional.co.nz
中国责任单位：金佰利（中国）有限公司上海市黄浦区淡水路299号12楼200025咨询电话：4006517268
www.kcprofessional.com.cn
Distributed in Singapore by Kimberly-Clark Singapore Pte. Ltd, 81 Tuas South Avenue 8, Singapore 637558.
Tel: 1 800 562 5275 www.kcprofessional.com.sg
9. Center sliding door in middle of dispense opening.
Align sliding door to upper sliding track.
10. Rotate sliding door to snap it securely into upper track.
11. Slide door to left side of dispenser to align 3 teeth
of sliding door to 3 notches on sliding track. Gently
push sliding door to engage the bottom sliding track,
allowing the door to snap fully into secured position.
12.
11.
9.
8.
6.
10.
7.
12. Test sliding door left and right to make sure door slides
smoothly.
-
1
-
2
Kimberly-Clark 58761 Standard Roll Toilet Paper Dispenser 4 Roll Vertical Faceplate Mode d'emploi
- Taper
- Mode d'emploi
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Kimberly-Clark 53696 ICON Coreless Standard Roll Toilet Paper Mode d'emploi
-
Kimberly-Clark KCC53706 ICON Automatic Roll Towel Recessed Dispenser Housing Manuel utilisateur
-
Kimberly-Clark ICON Automatic Roll Towel Dispenser Mode d'emploi
-
Kimberly-Clark ICON Automatic Soap and Sanitizer Dispenser Faceplate Mode d'emploi
-
Kimberly-Clark 53697 Automatic Roll Towel Recessed Dispenser Housing Mode d'emploi
-
Kimberly-Clark Kimberly-Clark 58724 Automatic Soap and Sanitizer Dispenser Mode d'emploi
-
Kimberly-Clark Kimberly-Clark Standard Roll Toilet Paper Dispenser 2 Roll Vertical Mode d'emploi
-
Kimberly-Clark Icon Automatic Roll Towel Narrow Recessed Dispenser Housing Mode d'emploi
-
Kimberly-Clark ICON Automatic Roll Towel Recessed Dispenser Housing Mode d'emploi
-
Kimberly-Clark Kimberly-Clark 53696 Standard Roll Toilet Paper Dispenser 2 Roll Vertical Mode d'emploi
