Viper AS516TO Le manuel du propriétaire

B

USER MANUAL

AS5160 & AS5160T / AS516TO

AS5160 & AS5160T

AS516TO

Nilfisk Inc.

9435 Winnetka Avenue North

Minneapolis, MN 55445

www.usviper.com

VS12002

Rev 01

17APR 2018

Model: 50000401 / 50000406 / 50000539

TABLE OF CONTENTS

ENGLISH

USER MANUAL………………………………………………

1-27

FRANÇAIS

MANUEL UTILISATEUR……………………………………

28-54

ESPAÑOL

INSTRUCCIONES DE USO…………………………………

55-81

USER MANUAL

ENGLISH

1

TABLE OF CONTENTS

INTRODUCTION ........................................................................................................................... 2

GUIDE PURPOSE AND CONTENTS ....................................................................................................................... 2

HOW TO KEEP THIS GUIDE ................................................................................................................................... 2

DECLARATION OF CONFORMITY ....................................................................................................................... 2

ACCESSORIES AND MAINTENANCE ................................................................................................................... 2

CHANGE AND IMPROVEMENT ............................................................................................................................. 2

SCOPE OF APPLICATION........................................................................................................................................ 2

MACHINE IDENTIFICATION DATA ...................................................................................................................... 2

TRANSPORT AND UNPACKING ............................................................................................................................ 3

SAFETY .......................................................................................................................................... 3

VISIBLE SYMBOLS ON THE MACHINE ............................................................................................................... 3

SYMBOLS THAT APPEAR ON THEINSTRUCTION FOR USEMANUAL .......................................................... 3

GENERAL SAFETY INSTRUCTION ....................................................................................................................... 4

MACHINE DESCRIPTION ........................................................................................................... 6

MACHINE STRUCTURE .......................................................................................................................................... 6

CONTROL PANEL..................................................................................................................................................... 7

DISPLAY WINDOW OF CHARGER INDICATON LIGHT .................................................................................... 7

TECHNICAL PARAMETERS ................................................................................................................................... 8

WIRING DIAGRAM .................................................................................................................................................. 9

OPERATING GUIDE................................................................................................................... 12

BATTERY CHECK/SETTING ON A NEW MACHINE ........................................................................................ 12

BATTERY INSTALLATION AND BATTERY TYPESETTING (WET OR GEL/ AGM) ................................... 13

ACCORDING TO THE TYPE OF BATTERIES (WET OR GEL / AGM) SET THE MACHINE ......................... 14

BRUSH/PAD-HOLDER INSTALLATION AND UNINSTALLATION ................................................................ 15

ADJUSTING THE BALANCE OF SQUEEGEE ..................................................................................................... 16

SOLUTION OR WASHING WATER TANK FILLING ......................................................................................... 16

MACHINE START AND STOP ............................................................................................................................... 16

ADJUSTING THE LEVEL OF ORBITALDECK (ONLY FOR ORBITAL MACHINE) ....................................... 17

MACHINE OPERATION (SCRUBBERING AND DRYING) ............................................................................... 17

TANK EMPTYING................................................................................................................................................... 18

AFTER USING THE MACHINE ............................................................................................................................. 19

MACHINE LONG INACTIVITY............................................................................................................................. 20

FIRST PERIOD OF USE .......................................................................................................................................... 20

MAINTENANCE .......................................................................................................................... 20

SCHEDULED MAINTENANCE TABLE ............................................................................................................... 20

BATTERY CHARGING ........................................................................................................................................... 21

BRUSH/PAD CLEANING ....................................................................................................................................... 22

SOLUTION FILTER CLEANING ........................................................................................................................... 22

SQUEEGEE CLEANING ......................................................................................................................................... 23

SQUEEGEE BLADE CHECK AND REPLACEMENT .......................................................................................... 24

TANK AND VACUUM GRID WITH FLOAT CLEANING, AND COVER GASKET CHECK .......................... 25

MACHINE WORKING HOUR CHECK.................................................................................................................. 26

FUSE CHECK/REPLACEMENT ............................................................................................................................. 26

ACCESSORIES/OPTIONS ....................................................................................................................................... 27

TROUBLESHOOTING ................................................................................................................ 27

SCRAPPING ................................................................................................................................. 27

USER MANUAL

ENGLISH

2

INTRODUCTION

CAUTION!

Some general and detailed machine information is not included in this guide.

Please refer to Instruction for Use Manual on supplied CD-ROM reading by Adobe® Reader®.

NOTE

The numbers in brackets refer to the components shown in Machine Description chapter.

GUIDE PURPOSE AND CONTENTS

The purpose of this Quick Start Guide is to provide the operator with all basic information to use the machine prop-

erly. For information about technical characteristics, operation, machine inactivity, spare parts and safety conditions

etc., please refer to Instruction for Use manual on supplied CD-ROM.

Before performing any procedure on the machine, the operators and qualified technicians must read the Instruction

for Use manual. Contact our company in case of doubts concerning the interpretation of the instructions or for any

further information.

HOW TO KEEP THIS GUIDE

The Quick Start Guide must be kept near the machine, inside an adequate case, away from liquids and other sub-

stances that can cause any damage to it.

DECLARATION OF CONFORMITY

Declaration of Conformity is supplied with the machine and certifies machine conformity with the law in force.

NOTE

The copies of the original declaration of conformity are provided together with the machine

documentation.

ACCESSORIES AND MAINTENANCE

All the necessary operation, maintenance and repair procedures must be made by qualified personnel, our company

appointed repair center. ONLY original or approved spare parts and accessories can be used.

Contact our company customer service for any service or purchase of accessories or spare parts if necessary.

CHANGE AND IMPROVEMENT

We committed to continuous improvement of its products, the company reserves the right to the machine changes

and improvements without informing in additional.

SCOPE OF APPLICATION

The scrubber applies to commercial and industrial use. It is suitable for cleaning smooth and solid floor, operating

by a qualified personnel in safety circumstance. It is not suitable for outdoor use or carpet or rough floor cleaning.

MACHINE IDENTIFICATION DATA

The machine serial number and model name are marked on the serial label.

This information is useful. Use the following table to write down the machine identification data when requiring

spare parts for the machine.

MACHINE MODEL...........................................................................

MACHINE SERIAL NUMBER.........................................................

USER MANUAL

ENGLISH

3

TRANSPORT AND UNPACKING

When the carrier delivers the machine, make sure the packaging and machine are both whole and undamaged. If

any damaged, make the carrier know the damage and before accepting the goods, reserve the right in compensation

of the damage.

Follow the instructions on packing strictly when unpacking the machine.

Check the package to ensure following items are included:

1. Technical documentations including Quick Start Guide manual, Instruction for Use Disk and on-board charger

manual if on-board charger is equipped.

2. Charger cable if on-board charger is equipped.

3. Two fuses, the low power circuit fuse (5A) and the Brush release fuse (20A).

SAFETY

The following symbols indicate potentially dangerous situations. Always read this information carefully and take

all necessary precautions to safeguard people and property.

VISIBLE SYMBOLS ON THE MACHINE

WARNING!

Read all the instructions carefully before performing any operation on the machine.

WARNING!

Do not wash the machine with direct or pressurized water jets.

WARNING!

Do not use the machine on slopes with a gradient exceeding that is defined in the specifi-

cation.

SYMBOLS THAT APPEAR ON THEINSTRUCTION FOR USEMANUAL

DANGER!

It indicates a dangerous situation with risk of death for the operator.

WARNING!

It indicates a potential risk of injury for people.

CAUTION!

It indicates a caution or a remark related to important or useful functions.

Pay attention to the paragraphs marked by this symbol.

NOTE

It indicates a remark related to important or useful functions.

CONSULTATION

It indicates the necessity to refer to the Instruction for Use manual before performing any

procedure.

USER MANUAL

ENGLISH

4

GENERAL SAFETY INSTRUCTION

Specific warnings and cautions to inform about potential damages to people and machine are shown below.

DANGER!

 This machine must be operated by trained and authorized personnel according to guidance of the

manual.

 Before performing any cleaning, maintenance, repair or replacement procedure, read all the

instructions carefully, ensure to turn the machine OFF and disconnect the battery connector.

 Do not operate the machine near toxic, dangerous, flammable and/or explosive powders, liquids or

vapour. This machine is not suitable for collecting dangerous powders.

 Do not wear jewels when working near electrical components.

 Do not work under the lifted machine without supporting it with safety stands.

 When using lead (WET) batteries, they may emit inflammable gas under normal use, must keep

sparks, flames, smoking materials and radiating, illuminating and burning items away from the

batteries.

 When charging lead (WET) batteries, they may emit hydrogen gas which may cause explosive. Must

ensure the charging environment is well ventilated and away from naked flames.

WARNING!

 Check the machine carefully before each use. Ensure that all the components have been well

assembled before use. Or it may causes damages to people and properties.

 Before using the battery charger, ensure that the values of frequency and voltage indicated on the

machine serial number label match those of mains.

 Never move the machine by pulling the battery charger cable. Do not let the cable through a closed

door, or winding on sharp edges or corners. Do not run the machine on the battery charger cable.

Keep the battery charger cable away from heated surfaces.

Do not charge the batteries if the battery charger cable or the plug are damaged.

 To reduce the risk of fire, electric shock, or injury, make sure machine is off before leaving.

 Use or store the machine indoors in dry conditions, it is not allowed for outdoor use.

 The machine both storage and working temperature must be between 0 °C and +40 °C, the humidity

of air must be between 30% - 95%.

 Do not use the machine on slopes with a gradient exceeding as specification show.

 When using and handling floor cleaning detergents, follow the instructions on the labels of the

detergent bottles and wear suitable gloves and protections.

 Use brushes and pads supplied with the machine or defined in the manual. Using other brushes or

pads could reduce safety.

 In case of machine malfunctions, ensure that these are not due to lack of maintenance. If necessary,

request assistance from the authorized personnel or from an authorized Service Center.

 Take all necessary precautions to prevent hair, jewels and loose clothes from being caught by the

machine moving parts.

 Do not use the machine in particularly dusty areas.

Do not wash the machine with direct or pressured water jets, or with corrosive substances.

 Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.

USER MANUAL

ENGLISH

5

 Do not lean liquid containers on the machine, use the relevant can holder.

 To avoid damaging the floor, do not allow the brush/pad to operate while the machine is stationary.

 In case of fire, use a dry powder fire extinguisher. Do not use liquid fire extinguishers.

 Do not remove or modify the machine stickers.

 Do not tamper with the machine safety guards and follow the ordinary maintenance instructions

scrupulously.

 Pay attention during machine transportation when temperature is below freezing point. The water in

the recovery tank and in the hoses could freeze and cause seriously damage to the machine.

 If spare parts need be replaced, order ORIGINAL spare parts from an Authorized Dealers or

Retailers.

 Return the machine to the Service Center if it doesn’t work as usual or it is in condition such as

damaged, placed outdoors, dropped into water.

 To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant

chapter of this Manual, must be performed by the authorized personnel or an authorized Service

Center.

 The machine must be properly disposed of, because the presence of toxic-harmful materials

(batteries, etc.), which are subject to standards that require disposal in special centers (see Scrapping

chapter).

 This machine as a cleaning tool only, not for any other purpose use.

 Always keep the openings free from dust, hairs and any other foreign material which could reduce

the air flow. Do not use the machine if the openings are clogged.

 Use the machine only where a proper lighting is provided.

 This machine is not intended for use by persons with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the machine by a person responsible for their safety.

 Close attention is necessary when used near children.

 Children should be supervised to ensure that they do not play with the machine.

 While using this machine, take care not to cause damage to people or objects.

USER MANUAL

ENGLISH

6

MACHINE DESCRIPTION

MACHINE STRUCTURE (as shown in Figure 1)

1. Recovery tank lid

2. Can holder

3. Handlebar

4. Control panel

5. Serial number plate/technical data

6. Squeegee lifting/lowering lever

7. Power supply cable holder

8. Power cable

9. Deck lifting/lowering pedal (only for disc machine)

a) Pedal position when deck is lifted

b) Pedal position when deck is lowered

10. Outlet cover

11. Squeegee knobs

12. Reset label

13. Squeegee vacuum hose

14. Squeegee

15. Squeegee balance adjusting knob

16. PA Connector

17. Rear steering wheels

18. Solution filter

19. Front wheels on fixed axle (A).

Driving wheels (B)

20. Brush/pad-holder

21. Brush/pad-holder deck

22. Recovery water drain hose

23. Solution tank

24. Hinge

25. Recovery tank

26. Filter support

27. Filler hose holder

28. Filter cover

29. Splash guard bristle 510mm

30. Tank cover gasket

31. Float ball filter

32. Solenoid valve

(*): Optional

(A): Only for machine without traction

(B): Only for machine with traction

Figure 1

USER MANUAL

ENGLISH

7

CONTROL PANEL (as shown in Figure 2)

33. Machine backward switch (B)

34. Safe switch

35. Ignition key (0 - I)

36. Discharged battery warning light (red)

37. Semi-discharged battery warning light (yellow)

38. Charged battery warning light (green)

39. Hour meter

40. Speed adjuster (B)

41. Flow increase switch

42. Solution flow indicator

43. Flow decrease switch

44. Brush/pad-holder release switch (only for disc machine)

Extra pressure active (only for orbital machine)

45. Vacuum system switch

46. Brush/pad-holder and vacuum system switch (only for

disc machine)

Pad deck moving up/down and Brush/pad-holder and va-

cuum system switch (only for orbital machine)

47. Charging red LED

48. Charging yellow LED

49. Charging green LED

50. Security cover of charging jack

51. Overload protector of brush

52. Overload protector of traction (B)

53. Overload protector of vacuum

54. Battery connector (red).

55. Tank safety cable

(*): Optional

(A): Only for machine without traction

(B): Only for machine with traction

DISPLAY WINDOW OF CHARGER INDICATON LIGHT (as shown in Figure 2)

1. At the beginning of charging, the red LED (47) of charger normally on. It is the first stage of charging.

2. After charging some time, the red LED (47) turns off, the yellow LED (48) turns on, this is the second stage of

charging.

3. After charging finish, the yellow LED (48) off, the green LED (49) turns on to indicate that the battery is fully

charged.

Figure 2

40

42

35

46 45 44

36

39

41

43

38

37

54

55

34 3433

47 48 49

53 52 51 50

BRUSHTRACTION

VACUUM

USER MANUAL

ENGLISH

8

NOTE

When charging, if the yellow LED (48) of charger is on, it may be caused by: Battery and charg-

er does not match, battery is not connected well, or output is short-circuited.

The red LED of charger flashing may be caused by charger internal short circuit.

TECHNICAL PARAMETERS

Model

Parameter Type

Units

AS5160

AS5160T

AS5160TO

Packing dimensions (L X W X H)

mm/Inches

(1370 x 600 x 1220 mm) / (54 x 24 x 48 Inches)

Machine Height

mm/Inches

1000 mm / 39.4 Inches

Machine Length

mm/Inches

1310 mm / 51.6 Inches

Machine Width (without squeegee)

mm/Inches

550 mm / 21.7 Inches

Machine weight with empty tanks

(without batteries)

Kg/Lbs.

85 Kg / 187 Lbs.

93 Kg/205 Lbs.

120 Kg/264 Lbs.

Gross Vehicle Weight (GVW)

Kg/Lbs.

214.8 Kg / 473Lbs.

222.8 Kg / 490 Lbs.

240 Kg / 528 Lbs.

Shipping Weight

Kg/Lbs.

115 Kg / 253 Lbs.

123 Kg / 271 Lbs.

150 Kg / 330 Lbs.

Solution tank capacity

L / Gal

61 L / 16 Gal.

Recovery tank capacity

L / Gal

61 L / 16 Gal.

Vacuum motor power

Watt / H.P.

350 W / 0.47 H.P.

Vacuum capacity

mm/In of H2O

1200 mm / 47.2 In of H2O

Climbing capacity (max)

% grade

2%

Front wheel diameter

mm/Inches

200 mm / 8 Inches

Rear wheel diameter

mm/Inches

76 mm / 3 Inches

Sound level

dB (A)

69 +/- 3 dB (A)

Solution Flow (max) per setting

L / Gal per minute

(0.7/1.2/1.7/2.2) Liters (0.2/0.3/0.45/0.6) Gallons

Working width

mm/Inches

510 mm / 20 Inches

Squeegee width

mm/Inches

790 mm / 31.1 Inches

Brush/Pad diameter

mm/Inches

510 mm / 20 Inches

510 x 360 mm /20 x 14 Inches

Brush motor power

Watt / H.P.

450 Watt / 0.6 H.P

750 Watt / 1.0 H.P.

Brush speed

RPM

150

2200

Brush/Pad pressure (max)

Kg/Lbs.

27 Kg / 59.4 Lbs.

23 Kg / 50.6 Lbs.

40 - 50 Kg / 88 - 110 Lbs.

Drive motor Power

Watt / H.P.

N/A

150 W / 0.2 H.P.

250 W / 0.33 H.P.

Working Speed

Km / Miles per hour

N/A

0 - 4.0 Km / 0 - 2.5 Miles per hour

Forward speed

Km / Miles per hour

N/A

0 - 4.0 Km / 0 - 2.5 Miles per hour

Reverse speed

Km / Miles per hour

N/A

0 - 2.0 Km / 0 - 1.25 miles per hour

Handle Vibration Level (max)

m/S2

2.5

Voltage

DC

24 Volts

Batteries

Amp/hour

105/130 WET 105/140 AGM Ah

On-Board Battery Charger

Volts/Amps

24 Volt/10 Amp

24 Volt/13 Amp

Battery Compartment Size

(L x W x H)

mm/Inches

(350 x 350 x 300) mm / 13.8 x 13.8 x 11.8) Inches

USER MANUAL

ENGLISH

9

WIRING DIAGRAM (ONLY FOR DISC MACHINE WITHOUT TRACTION)

COMPONENTS

GAUGE

BAT

24V BATTERIES

RD1

RED/6AWG

CH

BATTERY CHARGER

RD2

RED/10AWG

EB1

CONTROL PANEL BOARD

RD4

RED/20AWG

ES1

ELECTROMAGNETIC SWITCH 24V (BRUSH MOTOR)

BK1

BLACK/6AWG

ES2

RELAY 24V (VACUUM MOTOR)

BK2

BLACK/10AWG

F1

LOW POWER CIRCUIT FUSE

BK3

BLACK/12AWG

F2

CIRCUIT BREAKER (BRUSH MOTOR)

BK5

BLACK/20AWG

F3

BRUSH RELEASE FUSE

BK6

BLACK/16AWG

F5

CIRCUIT BREAKER (VACUUM MOTOR)

RD-BK

RED-BLACK/20AWG

K1

KEY SWITCH

BN1

BROWN/12AWG

M1

BRUSH MOTOR

BN3

BROWN/20AWG

M2

VACUUM MOTOR

BN-BK

BROWN-BLACK/20AWG

EV

SOLENOID VALVE

BU

BLUE/20AWG

SW1

SAFETY SWITCH (BRUSH)

BU-BK

BLUE-BLACK/20AWG

SW2

SAFETY SWITCH (BRUSH)

YE

YELLOW/20AWG

WH

WHITE/20AWG

BAT CH

K1

EV

M1 M2

EB1

ES1 ES2

F2 F5

RD1

RD2

RD2 BN1

BK3

BN3

RD2

BK3

BK2 BK5

BK2

BK1

NC

F1

F3

SW1

RD4

RD-BK

BK2

RD2

BN3

J1

J2

SW2

IN1

8

91

16

RD4

ES1

ES2

BN-BK

YE

BU-BK

BN3

BU

BN3

RD-BK

BK6

2

6

7

3

4

5

10

11

14

15

12

13

IN1

BU

BK6

IN2 J5

J4

IN2

BK6

BK5

USER MANUAL

ENGLISH

10

WIRING DIAGRAM (ONLY FOR DISC MACHINE WITH TRACTION)

COMPONENTS

GAUGE

BAT

24V BATTERIES

RD1

RED/6AWG

CH

BATTERY CHARGER

RD2

RED/10AWG

EB1

CONTROL PANEL BOARD

RD4

RED/20AWG

EB2

ELECTRONIC BOARD (TRACTION SYSTEM)

BK1

BLACK/6AWG

ES1

ELECTROMAGNETIC SWITCH 24V (BRUSH MOTOR)

BK2

BLACK/10AWG

ES2

RELAY 24V (VACUUM MOTOR)

BK3

BLACK/12AWG

ES3

RELAY 24V (TRACTION SYSTEM)

BK4

BLACK/14AWG

F1

LOW POWER CIRCUIT FUSE

BK5

BLACK/20AWG

F2

CIRCUIT BREAKER (BRUSH MOTOR)

BK6

BLACK/16AWG

F3

BRUSH RELEASE FUSE

RD-BK

RED-BLACK/20AWG

F4

CIRCUIT BREAKER (TRACTION SYSTEM)

GN

GREEN/20AWG

F5

CIRCUIT BREAKER (VACUUM MOTOR)

GN-BK

GREEN-BLACK/20AWG

K1

KEY SWITCH

BN1

BROWN/12AWG

M1

BRUSH MOTOR

BN2

BROWN/14AWG

M2

VACUUM MOTOR

BN3

BROWN/20AWG

M3

DRIVE MOTOR

BN-BK

BROWN-BLACK/20AWG

EV

SOLENOID VALVE

BU

BLUE/20AWG

SW1

SAFETY SWITCH (BRUSH/TRACTION)

BU-BK

BLUE-BLACK/20AWG

SW2

SAFETY SWITCH (BRUSH/TRACTION)

OR

ORANGE/20AWG

SW3

REVERSING SWITCH

YE

YELLOW/20AWG

VR1

SPEED POTENTIOMETER

WH

WHITE/20AWG

USER MANUAL

ENGLISH

11

WIRING DIAGRAM (ONLY FOR ORBITAL MACHINE)

COMPONENTS

GAUGE

Key

CODE

Description

BAT

N/A

24V BATTERIES

RD1

RED/6AWG

CH

VS10262

BATTERY CHARGER

RD2

RED/10AWG

EB1

VS13201

CONTROL PANEL BOARD

RD3

RED/12AWG

EB2

VS13215

ELECTRONIC BOARD (TRACTION SYSTEM)

RD4

RED/20AWG

ES1

9095127000

ELECTROMAGNETIC SWITCH 24V (BRUSH MOTOR)

RD5

RED/14AWG

ES2

VS10201

RELAY 24V (VACUUM MOTOR)

BK1

BLACK/6AWG

ES3

VS10201

RELAY 24V (TRACTION SYSTEM)

BK2

BLACK/10AWG

F1

VS13208

LOW POWER CIRCUIT FUSE

BK3

BLACK/12AWG

F2

ZD48320

CIRCUIT BREAKER (BRUSH MOTOR)

BK4

BLACK/14AWG

F3

VS13208

BRUSH LIFT MOTOR FUSE

BK5

BLACK/20AWG

F4

VF99010C

CIRCUIT BREAKER (TRACTION SYSTEM)

BK6

BLACK/16AWG

F5

ZD48320

CIRCUIT BREAKER (VACUUM MOTOR)

RD-BK

RED-BLACK/20AWG

K1

9100001354

KEY SWITCH

GN

GREEN/20AWG

M1

VS10702

BRUSH MOTOR

GN-BK

GREEN-BLACK/20AWG

M2

VF90520

VACUUM MOTOR

BN1

BROWN/12AWG

M3

VS11702

DRIVE MOTOR

BN2

BROWN/14AWG

EV

VF90282

SOLENOID VALVE

BN3

BROWN/20AWG

N/A

BN-BK

BROWN-BLACK/20AWG

M5

VS10703

BRUSH LIFT MOTOR

BU

BLUE/20AWG

SW1

VS10202

SAFETY SWITCH (BRUSH/TRACTION)

BU-BK

BLUE-BLACK/20AWG

SW2

VS10202

SAFETY SWITCH (BRUSH/TRACTION)

OR

ORANGE/20AWG

SW3

VS10202

REVERSING SWITCH

YE

YELLOW/20AWG

VR1

VS10213

SPEED POTENTIOMETER

WH

WHITE/20AWG

11

WH

BN2

7

RD2

8

10

BU-BK

BK4

12

YE

VR1

BN2

BN3

1

BN3

J2 5

17

5

BK5

13

17

BK4

14

WH

3

ES3

9

11

GN-BK

B-

RD5

13

BN-BK

WH

OR

26

BK5

OR

1

2

3

8

6

F4

5

18

BK3

15

B+

M3

4

1

14

ES1

M1

BK4

ES3

YE

RD-BK

3

BU

7

RD-BK

2

3

12

RD4

9

WH

7

2

16

WH

M2

5

16

15

M5

ES2

YE

BU-BK

GN

BU

4

GN-BK

8

GN

EV

6

4

BN3

RD3

10

BK5

8

6

BK2

SW3

WH

RD4

SW2

J1

EB2

EB1

M2

M1

SW1

F3

F1

K1

BAT

BK1 BK5 BK2

BK4 BK3

RD2 BN3

BK3

BN1

RD2

CH

RD5

RD1

F5F2

ES2

ES1

USER MANUAL

ENGLISH

12

OPERATING GUIDE

WARNING!

On some points of the machine there are some adhesive plates indicating:

－ DANGER!

－ WARNING!

－ CAUTION!

－ CONSULTATION

While reading this Manual, the operator must pay particular attention to the symbols shown on the plates.

Do not cover these plates for any reason and immediately replace them if damaged.

BATTERY CHECK/SETTING ON A NEW MACHINE

WARNING!

The electric components of the machine can be seriously damaged if the batteries are either

improperly installed or connected. The batteries must be installed by qualified personnel only.

Set the function electronic board and the built-in battery charger according to the type of

batteries used (WET or GEL/AGM batteries). Check the batteries for damage before

installation. Disconnect the battery connector and the battery charger plug. Handle the

batteries with great care. Install the battery terminal protection caps supplied with the machine.

The machine can be supplied in one of the following modes:

A) Batteries (WET or GEL/ AGM) already installed and charged

1. Check that the batteries are connected to the machine with the connector (54).

2. Insert the ignition key (35) and turn it to "I". If the green warning light (38) turns on, the batteries are fully

charged. If the yellow (37) or red warning light (36) turns on, the batteries must be charged (see the procedure in

Maintenance chapter).

B) Without batteries

1. Buy appropriate batteries (see the Technical Data paragraph).

2. For battery choice and installation, apply to qualified battery Retailers.

3. Set the machine and the battery charger according to the type of batteries (WET or GEL/ AGM), as shown in the

next paragraph.

NOTE

The machine requires two 12 V batteries, connected

according to the diagram (Figure 3).

Figure 3

12V +

-

12V

+-

USER MANUAL

ENGLISH

13

BATTERY INSTALLATION AND BATTERY TYPESETTING (WET OR GEL/ AGM)

According to the type of batteries (WET or GEL/AGM), set the machine and electronic board of the battery charger

as follows: (only for disc machine)

NOTE

When install new batteries please refer to Figure 4 to adjust the DIP switches. Otherwise the bat-

teries may be damaged.

Machine setting (only for disc machine)

1. Turn the ignition key (35) to “I” and in the very first seconds of machine operation pay attention to the

following:

 If the first green warning light (38) is flashing, the machine is set to GEL/AGM.

 If the yellow warning light (37) is flashing, the machine is set to Discover EV AGM.

 If the red warning light (36) is flashing, the machine is set to WET.

2. If the setting need to be changed, perform the

following procedure.

3. The factory setting is for WET batteries.

If the setting correspond to the battery installation, go

to step6 directly. Otherwise, follow next steps 4~5.

4. Remove the screws on control panel (C, Figure 4),

then turn over the PCB (A Figure 4) to find the DIP

switch (B, Figure 4) for setting battery type (WET or

Discover EV AGM or GEL/AGM), (Refer to 1 or 2

or 3).

5. If the setting complete to the battery option. Install

the screws on control panel.

Battery charging (only for disc machine)

6. Charge the batteries. (See procedures in maintenance

chapter).

CAUTION!

Cut off all the power of the machine be-

fore perform the following procedure!

WET

BA

C

D

DIS-EV

GEL/AGW

OTHER

WET

DIS-EU

GEL/AGW

OTHER

OFF

Figure 4

Figure 4.1

1

WET BATTERIES

(NOTE: Turn the DIP switch 1

and 2 both to “OFF”. )

2

DISCOVER EV AGM

BATTERIES

(NOTE: Turn the DIP switch 1

to “ON” ; 2 to “OFF” .)

3

GENERAL GEL/AGM

BATTERIES

(NOTE: Turn the DIP switch 1

and 2 both to “ON” .)

USER MANUAL

ENGLISH

14

Battery charger setting (for disc machines with on-board battery charger)

7. Remove the screws (A, B, C, D, Figure 4.1).

8. Open the charger and find the sw1 (E, Figure 4.1).

9. Set the switches as the table of (Figure 4.1).

10. Install the screws (A, B, C, D, Figure 4.1) after setting complete.

ACCORDING TO THE TYPE OF BATTERIES (WET OR GEL / AGM), SET THE MACHINE AS FOL-

LOWS: (only for orbital machine)

NOTE

Regarding the factory setting, learn the bat-

tery type from boot time display according

to above table

1. Press both the buttons (A, Figure. 4) and (B) at the same

time, Insert the ignition key (D) and turn on the power,

after 0.5 second, enter battery setting mode. LED dis-

play during setting (C), Release the buttons.

2. The mode can be shift from 0 to 5 by pressing button

(B), or shift from 5 to 0 by pressing button (A). After the

battery mode setting is completed, turn off the power (D)

and the new setting of battery mode can be saved auto-

matically.

3. The battery type setting is completed.

Mode

Battery type/Battery

manufacturer

Battery charging

curve

LED display during

setting (C, Figure. 4.2)

Boot time display

0

WET

General WET curve

LED1 blink

twice

1

GEL/AGM

General GEL/AGM

curve

LED2 blink

twice

2

DISCOVER

LED3 blink

twice

3

OPTIMA

Both LED1 and

LED2 blink

twice

4

EXIDE

Both LED1 and

LED3 blink

twice

5

FULLRIVER

Both LED2 and

LED3 blink

twice

Figure 4.2

USER MANUAL

ENGLISH

15

Battery installation

1. Open the recovery tank cover (1) and check that the recovery tank (25) is empty; otherwise empty it with the

drain hose. (22)

2. Close the recovery tank cover (1).

3. Overturn the recovery tank (25) carefully.

4. The machine is supplied with cables suitable to install 2X12V batteries. Carefully put the batteries into the

compartment, then install them correctly.

5. Route and install the battery cable as shown in (Figure 3), then carefully tighten the nut on each battery terminal.

6. Place the protection cap on each terminal, then connect the battery connector (54).

7. Carefully lower the recovery tank (25).

BRUSH/PAD-HOLDER INSTALLATION AND UNINSTALLATION (only for disc machine)

NOTE

Install either the brush (A, Figure 5) or pad-holder (B and C, Figure 5) according to the type of

floor to be cleaned.

CAUTION!

Before installation or uninstallation of brush or pad-holder, make sure all the switches on ma-

chine are in off position and lifting the squeegee from the floor. The operator must be equipped

with suitable personnel protection devices, such as gloves to reduce the risk of accidents.

Proceed as following:

1. Insert the ignition key (35) and turn it to "O".

2. Lift the deck by pressing the pedal (9).

3. If equipped, turn the speed adjuster (40) to idle by

turning it counter-clockwise.

4. Place the brushes (A, Figure 5) or the pad-holder (B)

under the deck (21).

5. Lower the deck on the brushes/pad-holders by pressing

the pedal (9).

6. Turn the ignition key (35) to "I".

7. Brush/pad-holder and vacuum system switch (46).

8. Press one of the Brush/forward gear switch (34) to

engage the brush/pad-holder, then release it. If necessary,

repeat the procedure until the brushes/pad-holders are

engaged.

9. If Step No.8 above proves to be difficult, use the manual

method by turning the brush/pad-holder in the direction

opposite to the normal turning direction, and it can be

taken off. (as shown in Figure 5)

WARNING!

(Only for machine with traction) Turn the

speed adjuster (40) counter-clockwise to

drive the machine at the minimum speed.

Slightly press the switch (34), otherwise the

machine starts to move.

To engage the brush/pad-holder press the switch

(34) which turns on the brush/pad-holder motor.

10. To remove the brush/pad-holder lift the deck by pressing

the pedal (9), then press the switch (44), the brush/pad-

holder will be remove.

A

C

B

Figure 5

Figure 5.1

USER MANUAL

ENGLISH

16

Figure 7

H

A

G

E

D

F

B

PAD INSTALLATION AND UNINSTALLATION (only for orbital machine)

1. Lift the deck by pressing the switch (46).

2. Install and uninstall the pad (A, Figure 5.1)

ADJUSTING THE BALANCE OF SQUEEGEE

1. Install the squeegee and screw up the nut (H), then

connect the vacuum hose (G) to the squeegee.

2. Adjust the squeegee by squeegee adjusting handle (A,

Figure 6).

a) If there is gap between the ground and middle section

of rear squeegee blade (B), adjust the knob (A) in

counterclockwise direction (F) until all section of rear

squeegee blade good contact with ground, the front

blade touch the ground slightly.

b) If there is gap between the ground and both end

section of rear blade (C and D), adjust the knob (A) in

clockwise direction (E) until all section of rear blade

good contact with the ground, the front blade touch

the ground slightly.

SOLUTION OR WASHING WATER TANK

FILLING

1. Open the water inlet cover (B, Figure 7).

2. Filling water or solution suitable for work performance

through the water inlet with filter.

The solution temperature must not exceed +104F

(+40°C).

3. Do not overfill the tank, refer to water level indicator (H)

for the water volume.

WARNING!

Use only low-foam and non-flammable de-

tergents, intended for automatic scrubber

applications.

MACHINE START AND STOP

Starting the machine

1. Prepare the machine as shown in the previous paragraph.

2. Insert the ignition key (A, Figure 8) and turn it to "I". Check that the green warning light (B) turns on (charged

battery). If the yellow (C) or red warning light (D) turns on, turn the ignition key back to “0” and charge the

batteries (see the procedure in Maintenance chapter).

3. Drive the machine to the working area:

 By pushing it with the hands on the handlebar (E) (only for machine without traction).

 By pushing it with the hands on the handlebar (E) and pressing the switch (F) to move forward, or pressing the

switch (F) together with the switch (G) to move backward (only for machine with traction). The forward speed

can be adjusted with the adjuster (H).

4. Lower the squeegee (I) with the lever (J).

5. Lower the brush/pad-holder deck (K) by lifting the pedal (L). (only for disc machine)

6. Press the brush/pad-holder switch (M) and the vacuum system switch (N).

7. Press the washing water flow control switches (O) as necessary, depending on the type of cleaning to be

performed.

8. Start cleaning:

 (only for machine without traction) by pushing the machine with the hands on the handlebar (E) and pressing

the switch (F).

D

B

C

EF

A

H

G

H

Figure 6

USER MANUAL

ENGLISH

17

Figure 8

K

I

J

L

FGF

O

H

A

DCB

E

M

N

 (only for machine with traction) by pushing the machine with the hands on the handlebar (E) and by pressing

the switch (F). If necessary, the forward speed can be adjusted with the adjuster (H).

NOTE

To move the machine forward, press either

the left or right switch (F) or both.

Stopping the machine

9. Stop the machine by using the handlebar (E) (only for

machine without traction). Stop the machine by releasing

the switches (F) (only for machine with traction).

10. Stop the brushes and the vacuum system by pressing the

switch (M). The vacuum system stops after a few seconds.

11. Lift the brush/pad-holder deck (K) by pressing the pedal

(L). (only for disc machine)

12. Lift the squeegee (I) with the lever (J).

13. Turn the ignition key (A) to "0".

14. Make sure that the machine cannot move independently.

ADJUSTING THE LEVEL OF ORBITALDECK

(ONLY FOR ORBITAL MACHINE)

1. Lower the brush/pad-holder deck by press the Brush/pad-

holder switch (M Figure 8).

2. Adjust the level of orbital deck by adjusting handle (A,

Figure 8.1).made the bubble in the middle (B Figure 8.1).

MACHINE OPERATION (SCRUBBERING AND

DRYING)

1. Start the machine as shown in previous paragraphs.

2. While keeping both hands on the handlebar press the safety

switch (F, Figure 8), then manoeuvre the machine and start

scrubbing/drying the floor.

3. If necessary, stop the machine then adjust squeegee according

to section “Adjusting balance of squeegee”.

NOTE

For correct scrubbing/drying of floors at the sides

of the walls, Suggests to go near the walls with the

right side of the machine (A and B, Figure 9) as

shown in the figure.

Figure 8.1

USER MANUAL

ENGLISH

18

CAUTION!

To avoid any damage to the floor surface, turn off the brushes/pad-holders when the machine

stops in one place.

Battery discharge during operation

Until the green warning light (A, Figure 10) stays on, the

batteries allow the machine to work normally. When the green

warning light (A) turns off, and the yellow warning light (B)

turns on, it is advisable to charge the batteries, because the

remaining charge will last for a few minutes (depending on

battery characteristics and work to be performed). When the

red warning light (C) turns on, batteries are fully discharged.

After a few seconds, the brush/pad-holder is automatically

tuned off, while the (only for machine with traction) drive

system stay on, to finish drying the floor and drive the

machine to the appointed recharging area.

CAUTION!

Do not use the machine with discharged bat-

teries, to avoid damaging the batteries and

reducing the battery life.

TANK EMPTYING

An automatic float shut-off system (A, Figure 11)blocks the

vacuum system when the recovery water tank (B) is full. The

vacuum system deactivation is signaled by a sudden increase

in the vacuum system motor noise frequency, also the floor

has not dried.

Figure 9

A

B

Figure 10

EG

H

F

CB A

D

I

La page charge ...

Viper AS516TO Le manuel du propriétaire

Ce manuel convient également à

Viper AS516TO Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents