VTech IS8102 Manuel utilisateur

Marque: VTech

Modèle: IS8102

Catégorie: Téléphones

Taper: Manuel utilisateur

User’s manual

Go to www.vtechphones.com

to register your product for

enhanced warranty support

and latest VTech product

news.

Telephones identified with this

logo have reduced noise and

interference when used with most

T-coil equipped hearing aids and

cochlear implants. The TIA-1083

Compliant Logo is a trademark of

the Telecommunications Industry

Association. Used under license.

Compatible with

Hearing Aid T-Coil

TIA-1083

Congratulations

on purchasing your new VTech product. Before

using this telephone, please read

Important safety instructions.

This manual has instructions on how to set up and

using the handset, see the Quick start guide that

came with your telephone base.

You may also view or download the online user’s

manual for a full set of installation and operation

instructions at www.vtechphones.com.

In Canada, visit www.vtechcanada.com.

IS8121 base Do not place

the handset in

the charger.

Add and register a handset

You can add new IS8102 handsets

(purchased separately) to your IS8121-2/

IS8121-3/IS8121-4/IS8121-5 telephone

system. Your telephone system supports a

maximum of 5 handsets.

Each handset must be registered with

the telephone base before use. When

first purchased, each expansion handset

displays To register HS... and ... see manual

alternately.

• Charge the new handset without interruption for

at least 30 minutes before registering it to the

telephone base.

• You cannot register a handset if any other system

handset is in use.

To register a handset to IS8121-2/ IS8121-3/

IS8121-4/IS8121-5 telephone base:

1. Put the handset you wish to register on the

telephone base cradle.

2. The handset shows Registering.... If the

registration is successful, the handset

screen displays Registered and beeps.

The handset is now registered with the

telephone base.

If registration fails, Registration failed appears on

the handset screen. The handset shows To register

HS... and see manual alternately and the telephone

base returns to idle mode. This may take up to ﬁve

minutes to occur. Please start again from Step 1.

Deregister handsets

If you want to replace a handset or reassign the

designated handset number of a registered

handset, you must deregister all the handsets and

then individually register each handset.

If you want to register a handset to another

telephone base, you must deregister all handsets,

and then register each handset individually to the

desired telephone base.

To deregister all handsets from the telephone base:

1. Press and hold FIND HS on the telephone

base for about 10 seconds until the IN USE

light on the telephone base turns on and

starts ﬂashing.

IS8121 Base

2. Immediately press FIND HS again. You must

press FIND HS while the IN USE light is still

ﬂashing. The IN USE light turns off, and you

hear a conﬁrmation tone.

3. All handsets display To register HS...

and see manual alternately when the

deregistration process completes. The

deregistration process takes about 10

seconds.

• If the deregistration process fails, you may

need to reset the system and try again. To reset,

unplug the power from the telephone base and

plug it back in.

• You cannot deregister the handsets if any other

system handset is in use.

• Even if the battery is depleted, you can still

deregister the handsets by following the steps.

After the handset is charged for at least 10

minutes, the screen shows To register HS... and

see manual alternately.

Operating range

This cordless telephone operates with the

maximum power allowed by the Federal

Communications Commission (FCC). Even

so, this handset and telephone base can

communicate over only a certain distance

which can vary with the locations of the

telephone base and handset, the weather,

and the layout of your home or ofﬁce.

When the handset is out of range, the handset

displays Out of range OR no power at base.

If there is a call while the handset is out of

range, it may not ring, or if it does ring, the

call may not connect well when you press .

Move closer to the telephone base, and

then press to answer the call. If the handset

moves out of range during a telephone

conversation, there may be interference. To

improve reception, move closer to the

telephone base.

IS8102

DECT 6.0 accessory handset

for use with VTech models

IS8121-2/IS8121-3/IS8121-4/IS8121-5

The ENERGY STAR® program (www.

energystar.gov) recognizes and

encourages the use of products

that save energy and help protect

our environment. We are proud to

mark this product with the ENERGY

STAR® label indicating it meets the

latest energy efﬁciency guidelines.

Before use

When using your telephone equipment, basic

safety precautions should always be followed to

reduce the risk of ﬁre, electric shock and injury,

including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on

the product.

3. Unplug this product from the wall outlet before

cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.

4. Do not use this product near water such as near

a bath tub, wash bowl, kitchen sink, laundry tub

or a swimming pool, nor in a wet basement or

shower.

5. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

6. Avoid placing the telephone system in places

with extreme temperature, direct sunlight, or

other electrical devices. Protect your phone

from moisture, dust, corrosive liquids and

fumes.

7. Slots and openings in the back or bottom of the

telephone base and handset are provided for

ventilation. To protect them from overheating,

these openings must not be blocked by placing

the product on a soft surface such as a bed, sofa

or rug. This product should never be placed

near or over a radiator or heat register. This

product should not be placed in any area where

proper ventilation is not provided.

8. This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply in your home or ofﬁce, consult your

dealer or local power company.

9. Do not allow anything to rest on the power

cord. Do not install this product where the cord

may be walked on.

10. Never push objects of any kind into this product

through the slots in the telephone base or

handset because they may touch dangerous

voltage points or create a short circuit. Never

spill liquid of any kind on the product.

11. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the telephone base or handset other

than speciﬁed access doors may expose you

to dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when the

product is subsequently used.

IMportant safety

instructions

12. Do not overload wall outlets and extension

cords.

13. Unplug this product from the wall outlet and

refer servicing to an authorized service facility

under the following conditions:

• When the power supply cord or plug is

damaged or frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or

water.

• If the product does not operate normally by

following the operating instructions. Adjust

only those controls that are covered by the

operation instructions. Improper adjustment

of other controls may result in damage

and often requires extensive work by an

authorized technician to restore the product

to normal operation.

• If the product has been dropped and the

telephone base and/or handset has been

damaged.

• If the product exhibits a distinct change in

performance.

14. Avoid using a telephone (other than cordless)

during an electrical storm. There is a remote risk

of electric shock from lightning.

15. Do not use the telephone to report a gas

leak in the vicinity of the leak. Under certain

circumstances, a spark may be created when

the adapter is plugged into the power

outlet, or when the handset is replaced in its

cradle. This is a common event associated

with the closing of any electrical circuit. The

user should not plug the phone into a power

outlet, and should not put a charged handset

into the cradle, if the phone is located in an

environment containing concentrations of

ﬂammable or ﬂame-supporting gases, unless

there is adequate ventilation. A spark in such an

environment could create a ﬁre or explosion.

Such environments might include: medical

use of oxygen without adequate ventilation;

industrial gases (cleaning solvents; gasoline

vapors; etc.); a leak of natural gas; etc.

16. Only put the handset of your telephone next to

your ear when it is in normal talk mode.

17. The power adapter is intended to be correctly

oriented in a vertical or ﬂoor mount position.

The prongs are not designed to hold the plug

in place if it is plugged into a ceiling, under-the-

table or cabinet outlet.

18. For pluggable equipment, the socket-outlet

shall be installed near the equipment and shall

be easily accessible.

19.

CAUTION: Use only the batteries

indicated in this manual. There may

be a risk of explosion if a wrong type of

battery is used for the handset. Use only the

supplied rechargeable batteries or

replacement batteries (BT162342/BT262342)

for the handset. Do not dispose of batteries in

a ﬁre. They may explode.

20. Use only the adapter included with this

product. Incorrect adapter polarity or voltage

can seriously damage the product.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use Only Supplied Battery.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for special

disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or

injury to the eyes or skin. The electrolyte may be

toxic if swallowed.

• Exercise care in handling batteries in order

not to create a short circuit with conductive

materials.

• Charge the battery provided with this product

only in accordance with the instructions and

limitations speciﬁed in this manual.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital

cordless telephones):

Wireless Technology Research, LLC (WTR), an

independent research entity, led a multidisciplinary

evaluation of the interference between portable

wireless telephones and implanted cardiac

pacemakers. Supported by the U.S. Food and

Drug Administration, WTR recommends to

physicians that:

Pacemaker patients

• Should keep wireless telephones at least six

inches from the pacemaker.

• Should NOT place wireless telephones directly

over the pacemaker, such as in a breast pocket,

when it is turned ON.

• Should use the wireless telephone at the ear

opposite the pacemaker.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless telephones.

Connect the charger

Charge the battery

12 hrs

Connect and charge battery

User’s manual

1 – Charging pole

Your telephone package contains the following

items. Save your sales receipt and original

packaging in the event warranty service is

necessary.

What’s in the box

Charger overview

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR2035

The battery is low and needs charging.

The battery is charging.

The battery is fully charged.

Handset ringer is off.

New voicemail received from your telephone service provider.

NEW

There are new caller ID log entries.

ANS ON Answering system is on.

MSG#

5/10 Number of new/old messages recorded.

ECO The ECO mode activates automatically to reduce power consumption when the

handset is within range of the telephone base.

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR2035

THIS SIDE UP

P / CE CÔTÉ VERS LE HAUT

oc-piles :

3342 (2.4V 400mAh Ni-MH)

VERTISSEMENT :

RPUNCTURE BATTERIES.

UPERCER LES PILES.

chine CR1535

1 – Visual ringer indicator

2 – CHARGE light

• On when the handset is charging in the

telephone base or charger.

3 – LCD display

4 – /CELL

• Press to make or answer a cell call.

• During a call, press to answer an

incoming cell call when you hear a call

waiting alert.

5 – HOME/FLASH

• Press to make or answer a home call.

• During a call, press to answer an

incoming home call when you receive a

call waiting alert.

6 – 1

• While reviewing a caller ID log entry,

press repeatedly to add or remove 1 in

Battery

indicators Battery status Action

The screen

is blank, or

shows Put in

charger and

ﬂashes.

The battery

has no charge

or very little

charge. The

handset

cannot be

used.

Charge

without

interruption

(at least 30

minutes).

The screen

shows Low

battery and

ﬂashes.

The battery has

enough charge

to be used for

a short time.

Charge

without

interruption

(at least 30

minutes).

The screen

shows

HANDSET X.

The battery is

charged. To keep

the battery

charged,

place it in the

charger when

not in use.

Handset overview

Display icons overview

Install the battery

LCD language setting

If you accidentally set the LCD language to Spanish or French, press MENU and then

enter 364# to change the handset LCD language back to English while the handset is

not in use.

The Bluetooth® word mark and logos are owned

by Bluetooth SIG, Inc. and any use of such marks

by VTech Holdings Limited is under license. VTech

Holdings Limited is a member of Bluetooth SIG,

Inc. Other trademarks and trade names are those

of their respective owners.

front of the telephone number before

dialing or saving it in the phonebook.

• Press and hold to set or dial your

voicemail number.

7 – TONE

• Press to switch to tone dialing

temporarily during a call if you have

pulse service.

8 – /SPEAKER

• Press to make or answer a call using the

speakerphone.

• Press to turn on the handset

speakerphone, press again to resume

normal handset use.

9 – MUTE/DELETE

• During a call, press to mute the

microphone.

• When the handset is ringing, press to

mute the ringer temporarily.

• While reviewing the redial list,

phonebook, caller ID log, allow list,

block list, or the star name list, press to

delete an individual entry.

• While predialing, press to delete

digits.

• When entering names or numbers,

press to delete a digit or character.

• When entering names or numbers,

press and hold to erase all digits or

characters.

• During message or announcement

playback, press to delete the

playing message or the recorded

announcement.

10 – MENU/SELECT

• Press to display the menu.

• Once in the menu, press to select an

item or save an entry or setting.

11 – /

• Press to show phonebook entries

when the telephone is not in use.

• Press to scroll up while in a menu.

• Press to increase the listening volume

when on a call, or increase the

message playback volume.

• While entering names or numbers,

press to move the cursor to the right.

• Press to review the caller ID log when

the telephone is not in use.

• Press to scroll down while in a menu.

• Press to decrease the listening volume

when on a call, or decrease the

message playback volume.

• While entering names or numbers,

press to move the cursor to the left.

12 – OFF/CANCEL

• During a call, press to hang up.

• While in a menu, press to cancel an

operation, back up to the previous

menu, or exit the menu display; or

press and hold this button to exit to

idle mode.

• When the handset is ringing, press to

mute the ringer temporarily.

• Press and hold while the handset is not

in use to erase the missed call indicator.

13 – QUIET

• Press and hold to set and turn on the

QUIET mode, or turn it off.

• When reviewing a caller ID log entry,

press repeatedly to view other dialing

options.

14 – CALL BLOCK/ VOICE

• While connected to one or two cell

phones, press to activate the voice

controlled application of one of the

connected cell phones.

• When the telephone is ringing, press

to block the incoming home call or cell

call.

• When on a home call or cell call, press

to block the call.

15 – REDIAL/PAUSE

• Press repeatedly to view the last 10

numbers dialed.

• While entering numbers,

press and hold to insert a dialing

pause.

For more support information

Speciﬁcations are subject to change without notice.

ne démontez pas l’appareil, mais apportez-le

plutôt à un centre de service qualiﬁé s’il doit

être réparé. En enlevant le couvercle, vous vous

exposez à des tensions dangereuses ou autres

dangers similaires. Un remontage inadéquat

peut être à l’origine d’une électrocution

lors d’une utilisation ultérieure de l’appareil.

Débranchez l’appareil avant de procéder au

nettoyage. Utilisez un chiffon humide et doux.

12. Ne surchargez pas les prises de courant et les

rallonges.

13. Débranchez cet appareil de la prise de courant

et communiquez avec le département de

service à la clientèle de VTech dans les cas

suivants :

• Lorsque le cordon d’alimentation est

endommagé ou écorché.

• Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé à une source

d’humidité telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement

en respectant les instructions de

fonctionnement. Réglez uniquement les

commandes indiquées dans le les instructions

de fonctionnement. Les réglages incorrects

des autres commandes pourraient provoquer

un dommage qui pourrait exiger un travail

exhaustif de la part d’un technicien autorisé

aﬁn de rétablir le fonctionnement normal de

l’appareil.

• Si le produit a été échappé et que le socle et/

ou le combiné a été endommagé.

• Si le produit afﬁche une nette diminution de

sa performance.

14. Évitez d’utiliser un téléphone (autre qu’un sans

ﬁl) pendant un orage. Les éclairs peuvent être à

l’origine d’une électrocution.

15. N’utilisez pas le téléphone pour rapporter une

fuite de gaz à proximité de la fuite. En certaines

circonstances, une ﬂammèche pourrait être

provoquée lorsque l’adaptateur est branché à

une prise de courant, ou lorsque le combiné

est déposé sur le socle. Ceci est un événement

commun associé à la fermeture d’un circuit

électrique. L’utilisateur ne devrait pas brancher

le téléphone à une prise de courant, et ne

devrait pas déposer le combiné chargé sur

le socle, si le téléphone se trouve à proximité

d’un endroit comportant des concentrations

de gaz inﬂammables, à moins que la ventilation

soit adéquate. Une ﬂammèche dans un tel

endroit pourrait provoquer un incendie ou une

explosion. De tels environnements peuvent

comprendre: des endroits où l’on utilise de

l’oxygène médical sans ventilation adéquate;

des gaz industriels (dissolvants de nettoyage,

des vapeurs d’essence, etc.); une fuite de gaz

naturel, etc.

16. Ne placez que le combiné de votre téléphone

près de votre oreille lorsqu’en mode de

conversation.

17. Ces adaptateurs ont été conçus pour être

orientés en position verticale ou montés au sol.

Les broches ne sont pas conçues pour maintenir

l’adaptateur en place si celui-ci est barnché

dans une prise au plafond ou sous une table/

armoire.

18. Pour le MATERIEL RACCORDE PAR PRISE DE

COURANT, le socle de prise de courant doit

etre installe a proximite du materiel et doit etre

aisement accessible.

19.

MISE EN GARDE: Il peut y avoir un

risque d’explosion si vous utilisez le mauvais

type de piles pour le téléphone. N’utilisez que

les piles rechargeable inclus ou les piles de

rechange (BT162342/BT262342). N’incinérez pas

les piles. Celles-ci risqueraient d’exploser.

20. N’utilisez que les adaptateurs inclus avec ce

produit. L’utilisation d’un adaptateur dont la

polarité ou la tension serait inadéquate risque

d’endommager sérieusement le produit et

mettre votre sécurité en péril.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent.

• Ne jetez pas la pile au feu. Vériﬁez les

instructions spéciﬁques de mise aux rebus

auprès des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile.

L’électrolyte qui s’en échapperait est corrosif et

pourrait causer des brûlures ou des blessures

aux yeux ou à la peau. L’électrolyte est toxique

si avalé.

• Soyez prudents lorsque vous manipulez les piles

aﬁn d’éviter les courts-circuits provoqués par

des matériaux conducteurs.

• Rechargez la pile incluse avec cet appareil,

selon les instructions et limites spéciﬁées dans

ce guide d’utilisation.

Stimulateurs cardiaques implantés dans

l’organisme

Les simulateurs cardiaques (s’applique uniquement

aux téléphones numériques sans ﬁl) :

L’organisme ‘Wireless Technology Research, LLC

(WTR)’, une ﬁrme de recherche indépendante,

a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans ﬁl portatifs

et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des

aliments et drogues (FDA) des États-Unis, la ﬁrme

WTR recommande aux médecins :

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une

distance d’au moins six pouces du stimulateur

cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl

directement sur le stimulateur cardiaque, tel

que dans une poche de chemise, lorsque celui-

ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en

l’appuyant sur l’oreille qui se trouve dans la

direction opposée au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a

pas identiﬁé de risque pour les détenteurs de

simulateurs cardiaques causés par les gens qui

utilisent un téléphone sans ﬁl à proximité de ceux-ci.

À propos des téléphones sans ﬁl

Conﬁdentialité : Les mêmes caractéristiques qui

constituent des avantages pour les téléphones sans

ﬁl afﬁchent également des restrictions. Les appels

téléphoniques sont transmis entre le combiné sans

ﬁl et le socle par le biais d’ondes radio ; il y a donc

la possibilité que vos conversations téléphoniques

sans ﬁl soient interceptées par des équipements

de réception radio se trouvant dans la portée du

combiné sans ﬁl. Pour cette raison, vous ne devez

pas percevoir les communications téléphoniques

sans ﬁl comme étant aussi conﬁdentielles que

celles des téléphones à cordons.

Alimentation électrique : Le socle de ce téléphone

sans ﬁl doit être branché à une prise électrique

fonctionnelle. La prise électrique ne doit pas être

contrôlée par un interrupteur mural. Les appels ne

pourront pas être effectués du combiné sans ﬁl si

le socle est débranché ou mis hors tension ou si le

courant est coupé.

Possibilité d’interférences aux téléviseurs :

Certains téléphones sans ﬁl fonctionnent sur des

fréquences pouvant causer des interférences aux

téléviseurs et aux magnétoscopes. Pour réduire

ou prévenir de telles interférences, ne placez

pas le socle du téléphone sans ﬁl près ou sur un

téléviseur ou magnétoscope. S’il y a présence de

parasites, il est conseillé d’éloigner le téléphone

sans ﬁl du téléviseur ou du magnétoscope aﬁn de

réduire possiblement les interférences.

Piles rechargeables : Manipulez les piles avec soin

aﬁn de ne pas les court-circuiter avec des bagues,

bracelets ou clés. Les piles ou le conducteur peut

surchauffer et causer des blessures. Respectez la

polarité adéquate entre la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure

métallique de nickel : Jetez ces blocs-piles de

manière écologique et sécuritaire. Ne les incinérez

pas et ne les percez pas. Tel que les autres piles

de ce type, elles pourraient dégager une matière

toxique qui peut causer des blessures corporelles

si elles sont brûlées ou percées.

The RBRC® seal

The RBRC seal on the nickel-metal

hydride battery indicates that VTech

Communications, Inc. is voluntarily

participating in an industry program to

collect and recycle these batteries at

the end of their useful lives, when

taken out of service within the United States and

Canada.

The RBRC program provides a convenient

alternative to placing used nickel-metal hydride

batteries into the trash or municipal waste, which

may be illegal in your area.

VTech’s participation in RBRC makes it easy for

you to drop off the spent battery at local retailers

participating in the RBRC program or at authorized

VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH

battery recycling and disposal bans/restrictions

in your area. VTech’s involvement in this program

is part of its commitment to protecting our

environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are

registered trademarks of Call2recycle, Inc.

FCC, ACTA and IC

regulations

FCC Part 15

NOTE: This equipment has been tested and

found to comply with the requirements for a

Class B digital device under Part 15 of the Federal

Communications Commission (FCC) rules. These

requirements are intended to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses and can radiate radio frequency energy

and, if not installed and used in accordance with

the instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

WARNING: Changes or modiﬁcations to this

equipment not expressly approved by the party

responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC

rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference

that may cause undesired operation. Privacy of

communications may not be ensured when using

this telephone.

To ensure safety of users, the FCC has established

criteria for the amount of radio frequency energy

that can be safely absorbed by a user or bystander

according to the intended usage of the product.

This product has been tested and found to comply

with the FCC criteria. The handset may be safely

held against the ear of the user. The telephone

base shall be installed and used such that parts

of the user’s body other than the hands are

maintained at a distance of approximately 20 cm (8

inches) or more.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC

rules and with technical requirements adopted

by the Administrative Council for Terminal

Attachments (ACTA). The label on the back or

bottom of this equipment contains, among

other things, a product identiﬁer in the format

US:AAAEQ##TXXXX. This identiﬁer must be

provided to your telephone service provider upon

request.

The plug and jack used to connect this equipment

to premises wiring and the telephone network

must comply with applicable Part 68 rules and

technical requirements adopted by ACTA. A

compliant telephone cord and modular plug is

provided with this product. It is designed to be

connected to a compatible modular jack that is also

compliant. An RJ11 jack should normally be used

This telephone is set up to comply with the energy-

conserving standards right out of the box. These

instructions are intended for California Energy

Commission (CEC) compliance testing only. When the

CEC battery charging testing mode is activated, all

telephone functions, except battery charging, will be

disabled.

To activate the CEC battery charging testing

mode:

1. Unplug the telephone base power adapter

from the power outlet. Make sure all handsets

are plugged with charged batteries before

proceeding.

2. While you press and hold FIND HS, plug the

telephone base power adapter back to the

power outlet.

3. After about 20 seconds, when the IN USE

light starts ﬂashing, release FIND HS and then

press it again within two seconds. You hear a

conﬁrmation tone. The IN USE light turns off and

all handsets display To register HS... and ...see

manual alternately. Allow up to one minute for

the process to complete.

If the phone fails to enter this mode, repeat all the

steps mentioned above. The telephone base will

be powered up as normal if you fail to press

FIND HS within two seconds in Step 3.

To deactivate the CEC battery charging testing

mode:

1. Unplug the telephone base power adapter from

the power outlet, and then plug it back in. Then

the telephone base is powered up as normal.

2. Put the handsets on the telephone base cradle

to begin registration.

3. The handset shows Registering... If the

registration is successful, the handset screen

displays Registered and beeps. The handset is

registered with the telephone base.

California Energy

Commission battery charging

testing instructions What does this limited warranty cover?

The manufacturer of this VTech Product warrants to

the holder of a valid proof of purchase (“Consumer”

or “you”) that the Product and all accessories

provided in the sales package (“Product”) are free

from defects in material and workmanship, pursuant

to the following terms and conditions, when

installed and used normally and in accordance with

the Product operating instructions. This limited

warranty extends only to the Consumer for Products

purchased and used in the United States of America

and Canada.

What will VTech do if the Product is not free from

defects in materials and workmanship during the

limited warranty period (“Materially Defective

Product”)?

During the limited warranty period, VTech’s

authorized service representative will repair or

replace at VTech’s option, without charge, a Materially

Defective Product. If we repair the Product, we may

use new or refurbished replacement parts. If we

choose to replace the Product, we may replace it with

a new or refurbished Product of the same or similar

design. We will retain defective parts, modules, or

equipment. Repair or replacement of the Product, at

VTech’s option, is your exclusive remedy. VTech will

return the repaired or replacement Products to you

in working condition. You should expect the repair or

replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If VTech

repairs or replaces a Materially Defective Product

under the terms of this limited warranty, this limited

warranty also applies to the repaired or replacement

Product for a period of either (a) 90 days from the

date the repaired or replacement Product is shipped

to you or (b) the time remaining on the original one-

year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, ﬁre, water or

other liquid intrusion.

2. Product that has been subjected to contact

with liquid, water, rain, extreme humidity or

heavy perspiration, sand, dirt or the like; but

then only to the extent the damage was not

caused by incorrectly securing the waterproof

Limited Warranty handset’s protective elements, for example,

failing to properly close a seal), or such

protective elements are damaged or missing

(e.g. a cracked battery door), or subjecting

a Product to conditions beyond its stated

speciﬁcations or limits (e.g. 30 minutes in 1

meter of fresh water).

3. Product that has been damaged due to repair,

alteration or modiﬁcation by anyone other

than an authorized service representative of

VTech;

4. Product to the extent that the problem

experienced is caused by signal conditions,

network reliability, or cable or antenna

systems;

5. Product to the extent that the problem is

caused by use with non-VTech accessories;

6. Product whose warranty/quality stickers,

product serial number plates or electronic

serial numbers have been removed, altered or

rendered illegible;

7. Product purchased, used, serviced, or

shipped for repair from outside the United

States of America or Canada, or used

for commercial or institutional purposes

(including but not limited to Products used for

rental purposes);

8. Product returned without a valid proof of

purchase (see item 2 below); or

9. Charges for installation or set up, adjustment of

customer controls, and installation or repair of

systems outside the unit.

How do you get warranty service?

To obtain warranty service in the United States of

America, please visit our website at

www.vtechphones.com or call 1 (800) 595-9511.

In Canada, go to

www.vtechcanada.com or dial 1 (800) 267-7377.

NOTE: Before calling for service, please review the

user’s manual - a check of the Product’s controls and

features may save you a service call.

Except as provided by applicable law, you assume

the risk of loss or damage during transit and

transportation and are responsible for delivery

or handling charges incurred in the transport

of the Product(s) to the service location. VTech

will return repaired or replaced Product under

this limited warranty. Transportation, delivery or

handling charges are prepaid. VTech assumes no

risk for damage or loss of the Product in transit. If

the Product failure is not covered by this limited

warranty, or proof of purchase does not meet the

terms of this limited warranty, VTech will notify you

and will request that you authorize the cost of repair

prior to any further repair activity. You must pay

for the cost of repair and return shipping costs for

the repair of Products that are not covered by this

limited warranty.

What must you return with the Product to get

warranty service?

1. Return the entire original package and

contents including the Product to the VTech

service location along with a description of the

malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales

receipt) identifying the Product purchased

(Product model) and the date of purchase or

receipt; and

3. Provide your name, complete and correct

mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech. It supersedes

all other written or oral communications related to

this Product. VTech provides no other warranties for

this Product. The warranty exclusively describes all

of VTech’s responsibilities regarding the Product.

There are no other express warranties. No one is

authorized to make modiﬁcations to this limited

warranty and you should not rely on any such

modiﬁcation.

State/Provincial Law Rights: This warranty gives you

speciﬁc legal rights, and you may also have other

rights, which vary from state to state or province to

province.

Limitations: Implied warranties, including those of

ﬁtness for a particular purpose and merchantability

(an unwritten warranty that the Product is ﬁt for

ordinary use) are limited to one year from the date

of purchase. Some states/provinces do not allow

limitations on how long an implied warranty lasts,

so the above limitation may not apply to you. In no

event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages

(including, but not limited to lost proﬁts or revenue,

inability to use the Product or other associated

equipment, the cost of substitute equipment, and

claims by third parties) resulting from the use of this

Product. Some states/provinces do not allow the

exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may

not apply to you.

Please retain your original sales receipt as proof of

purchase

Frequency

control Crystal controlled PLL synthesizer

Transmit

frequency Handset: 1921.536-1928.448 MHz

Channels DECT channel: 5

Nominal

effective

range

Maximum power allowed by FCC

and IC. Actual operating range may

vary according to environmental

conditions at the time of use.

Power

requirement Handset: 2.4V DC, AAA x 2,

Ni-MH battery

Charger: 6V DC @ 400mA

Memory Phonebook: 1000 memory

locations;

up to 30 digits and 15 characters

Caller ID log: 50 memory locations;

up to 24 digits and 15 characters

Call block: 1000 entries

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures

corporelles ou d’électrocution, suivez toujours ces

mesures préventives de base lorsque vous utilisez

votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en

garde inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise murale

avant de le nettoyer. N’utilisez pas de

nettoyeurs liquides ni en aérosol. N’utilisez

qu’un chiffon doux et légèrement humecté.

4. N’utilisez pas ce produit près de l’eau, tel que

près d’un bain, d’un lavabo, d’un évier de

cuisine, d’un bac de lavage ou d’une piscine, ou

dans un sous-sol humide ou sous la douche.

5. Ne déposez pas ce téléphone sur un chariot,

support ou table chancelants. L’appareil pourrait

tomber et être sérieusement endommagé.

6. Évitez d’installer le système téléphonique dans

les endroits soumis à une température extrême,

à la lumière directe du soleil ou à proximité

immédiate d’autres appareils électriques ou

électroniques. Protégez votre téléphone contre

les sources d’humidité, la poussière, les vapeurs

et les liquides corrosifs.

7. Le boîtier de l’appareil est doté de fentes et

d’ouvertures d’aération situées à l’arrière ou en

dessous. Aﬁn d’empêcher la surchauffe, ces

ouvertures ne doivent pas être obstruées en

plaçant l’appareil sur un lit, divan, tapis ou autre

surface similaires. Ne placez pas cet appareil à

proximité d’un élément de chauffage ni d’une

plinthe électrique. De plus, ne l’installez pas

dans une unité murale ou un cabinet fermé qui

ne possède pas d’aération adéquate.

8. Ne faites fonctionner cet appareil qu’avec le

type d’alimentation indiqué sur les étiquettes de

l’appareil. Si vous ne connaissez pas le voltage

de votre maison, consultez votre marchand ou

votre fournisseur d’électricité.

9. Ne déposez rien sur le cordon d’alimentation.

Installez cet appareil dans un endroit sécuritaire,

là où personne ne pourra trébucher sur la

ligne d’alimentation ni le cordon téléphonique

modulaire.

10. N’insérez jamais d’objets à travers les fentes et

ouvertures de cet appareil, car ils pourraient

toucher à des points de tension dangereux ou

court-circuiter des pièces, ce qui constituerait

un risque d’incendie ou d’électrocution.

N’échappez pas de liquides dans l’appareil.

11. Aﬁn de réduire les risques d’électrocution,

For C-UL compliance

only

for connecting to a single line and an RJ14 jack for

two lines. See the installation instructions in the

user’s manual.

The Ringer Equivalence Number (REN) is used to

determine how many devices you may connect to

your telephone line and still have them ring when

you are called. The REN for this product is encoded

as the 6th and 7th characters following the US: in

the product identiﬁer (e.g., if ## is 03, the REN is

0.3). In most, but not all areas, the sum of all RENs

should be ﬁve (5.0) or less. For more information,

please contact your telephone service provider.

This equipment must not be used with Party

Lines. If you have specially wired alarm dialing

equipment connected to your telephone

line, ensure the connection of this equipment

does not disable your alarm equipment. If you

have questions about what will disable alarm

equipment, consult your telephone service

provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must be

unplugged from the modular jack until the

problem has been corrected. Repairs to this

telephone equipment can only be made by the

manufacturer or its authorized agents. For repair

procedures, follow the instructions outlined under

the Limited warranty.

If this equipment is causing harm to the telephone

network, the telephone service provider may

temporarily discontinue your telephone service.

The telephone service provider is required to

notify you before interrupting service. If advance

notice is not practical, you will be notiﬁed as soon

as possible. You will be given the opportunity to

correct the problem and the telephone service

provider is required to inform you of your right

to ﬁle a complaint with the FCC. Your telephone

service provider may make changes in its facilities,

equipment, operation, or procedures that could

affect the proper functioning of this product. The

telephone service provider is required to notify

you if such changes are planned.

If this product is equipped with a corded or

cordless handset, it is hearing aid compatible.

If this product has memory dialing locations,

you may choose to store emergency telephone

numbers (e.g., police, ﬁre, medical) in these

locations. If you do store or test emergency

numbers, please:

Remain on the line and brieﬂy explain the reason

for the call before hanging up.

Perform such activities in off-peak hours, such as

early morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science

and Economic Development Canada’s licence-

exempt RSS(s). Operation is subject to the

following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference,

including interference that may cause undesired

operation of the device.

Privacy of communications may not be ensured

when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration

number only signiﬁes that the Industry Canada

technical speciﬁcations were met.

The Ringer Equivalence Number (REN) for this

terminal equipment is 1.0. The REN indicates

the maximum number of devices allowed to

be connected to a telephone interface. The

termination of an interface may consist of any

combination of devices subject only to the

requirement that the sum of the RENs of all the

devices not exceed ﬁve.

This product meets the applicable Innovation,

Science and Economic Development Canada

technical speciﬁcations.

VTech Communications, Inc. and its suppliers

assume no responsibility for any damage or loss

resulting from the use of this user’s manual. VTech

Communications, Inc. and its suppliers assume no

responsibility for any loss or claims by third parties

that may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste

555 Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or

1 (800) 267-7377 in Canada

• Privacy: The same features that make a cordless

telephone convenient create some limitations.

Telephone calls are transmitted between the

telephone base and the cordless handset by

radio waves, so there is a possibility that the

cordless telephone conversations could be

intercepted by radio receiving equipment

within range of the cordless handset. For

this reason, you should not think of cordless

telephone conversations as being as private as

those on corded telephones.

• Electrical power: The telephone base of this

cordless telephone must be connected to a

working electrical outlet. The electrical outlet

should not be controlled by a wall switch. Calls

cannot be made from the cordless handset if

the telephone base is unplugged, switched off

or if the electrical power is interrupted.

• Potential TV interference: Some cordless

telephones operate at frequencies that may

cause interference to televisions and VCRs.

To minimize or prevent such interference, do

not place the telephone base of the cordless

telephone near or on top of a TV or VCR.

If interference is experienced, moving the

cordless telephone farther away from the

TV or VCR often reduces or eliminates the

interference.

• Rechargeable batteries: Exercise care in

handling batteries in order not to create a short

circuit with conducting material such as rings,

bracelets and keys. The battery or conductor

may overheat and cause harm. Observe proper

polarity between the battery and the battery

charger.

• Nickel-metal hydride rechargeable batteries:

Dispose of these batteries in a safe manner. Do

not burn or puncture the battery. Like other

batteries of this type, if burned or punctured,

they could release caustic material which could

cause injury.

About cordless

telephones

Disclaimer and

Limitation of Liability Technical speciﬁcations

This power conserving technology reduces power

consumption for optimal battery performance. The

ECO mode activates automatically whenever the

handset is synchronized with the telephone base.

ECO mode

Taking care of your telephone

Your cordless telephone contains sophisticated

electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original

packing materials to protect your telephone if you

ever need to ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do

not use the handset outdoors in the rain, or handle

it with wet hands. Do not install the telephone base

near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power surges

harmful to electronic equipment. For your own

safety, take caution when using electrical appliances

during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

General product care

For operations and guides to help you using

your telephone, and for latest information and

supports, go and check the online help topics

and online FAQs.

Use your smartphone or mobile device to access

our online help.

• Go to https://help.vtechphones.com/is8102;

• Scan the QR code on the right. Launch the

camera app or QR code scanner app on

your smartphone or tablet. Hold the device’s

camera up to the QR code and frame it. Tap

the notiﬁcation to trigger the redirection of

the online help.

- If the QR code is not clearly displayed,

adjust your camera’s focus by moving

your device closer or further away until it

is clear.

You can also call our Customer Support at

1 (800) 595-9511 [in US] or 1 (800) 267-7377

[in Canada] for help.

Need help?

VTech IS8102 Manuel utilisateur

Marque: VTech

Modèle: IS8102

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech IS8102 User manual

Documents connexes

Autres documents

AT&T DLP70110 Manuel utilisateur