General Electric 040315A-0 Le manuel du propriétaire

GE Home Generator Systems

7,000 Watt

Home Generator System

Installation and

Start-Up Manual

Not for

Reproduction

2

DATE OF PURCHASE

GENERATOR

Model Number

Model Revision

Serial Number

ENGINE

Thank you for purchasing this quality-built GE home generator. We’re pleased that you’ve placed your confidence in the

GE brand. When operated and maintained according to the instructions in the operator’s manual, your home generator

will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with residential

generator systems and how to avoid them. This generator system is designed and intended only for use as an

optional home standby system that provides an alternate source of electric power and to serve loads such as heating,

refrigeration systems, and communication systems that, when stopped during any power outage, could cause

discomfort or inconvenience. Save these instructions for future reference.

This generator requires professional installation before use. The installer should follow the instructions completely.

Where to Find Us

You never have to look far to find support and service for your generator. For quick service when you need it most

fill out the information below and keep your original receipt with this manual. You may contact Customer Service at

(888) 575-8226, or click on SERVICE & SUPPORT at www.homestandbygeneratorsystems.com, which provides a list of

authorized dealers.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

Not for

Reproduction

3

Table of Contents

Important Safety Instructions ...............................4

Installation ................................................7

Home Owner Responsibilities ..........................................7

Installing Dealer/Contractor Responsibilities............................7

Unpacking Precautions................................................7

Shipment Contents ...................................................8

Generator Location ...................................................8

Electrical and Fuel Inlet Locations.....................................10

The Gaseous Fuel System ............................................12

Fuel Consumption ...................................................14

System Connectors ..................................................15

Grounding the Generator.............................................16

Final Installation Considerations ......................................19

Initial Start-up (No Load) .............................................20

Engine Adjustment ..................................................21

Test Shutdown(s) Procedure ..........................................22

Fuel Conversion .....................................................23

Schematic Diagram..................................................24

Wiring Diagram .....................................................25

Operation.................................................26

Automatic Operation Sequence .......................................26

Setting Exercise Timer ...............................................26

Installation Inspection ...............................................27

Not for

Reproduction

4

Safety Rules

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a degree

or level of hazard seriousness. A safety symbol may be used

to represent the type of hazard. The signal word NOTICE is

used to address practices not related to personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

Important Safety Instructions

Explosion

Fire

Electrical Shock

Rotating Parts

Hot Surface

Toxic Fumes

Chemical BurnExplosive PressureAuto Start

Lift Hazard

Read Manual

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

Operate this product ONLY outdoors.•

Install a battery operated carbon monoxide alarm near •

the bedrooms.

Keep exhaust gas from entering a confined area through •

windows, doors, ventilation intakes, or other openings.

WARNING The engine exhaust from this product contains

chemicals known to the State of California to cause cancer, birth

defects, or other reproductive harm.

WARNING Certain components in this product and related

accessories contain chemicals known to the State of California

to cause cancer, birth defects, or other reproductive harm. Wash

hands after handling.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings

in this manual, and the tags and decals affixed to the unit

are, therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the generator system unsafe.

Not for

Reproduction

5

WARNING Storage batteries give off explosive hydrogen gas

during recharging.

Slightest spark will ignite hydrogen and

cause explosion, resulting in death, serious

injury and/or property damage.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery contents could cause severe chemical burns.

A battery presents a risk of electrical shock and high short

circuit current.

DO NOT dispose of battery in a fire. Recycle battery.•

DO NOT allow any open flame, spark, heat, or lit cigarette during •

and for several minutes after charging a battery.

DO NOT open or mutilate the battery.•

Wear protective goggles, rubber apron, rubber boots and •

rubber gloves.

Remove watches, rings, or other metal objects.•

Use tools having insulated handles.•

WARNING Generator produces hazardous voltage.

Failure to properly ground generator could result

in electrocution.

Failure to isolate generator from utility power could result

in death or serious injury to electric utility workers due to

backfeed of electrical energy.

When using generator for backup power, notify utility company.•

DO NOT touch bare wires or bare receptacles.•

DO NOT use generator with electrical cords which are worn, •

frayed, bare or otherwise damaged.

DO NOT handle generator or electrical cords while standing in •

water, while barefoot, or while hands or feet are wet.

If you must work around a unit while it is operating, stand on an •

insulated dry surface to reduce the risk of a shock hazard.

DO NOT allow unqualified persons or children to operate or •

service generator.

In case of an accident caused by electrical shock, immediately •

shut down the source of electrical power and contact the local

authorities. Avoid direct contact with the victim.

Despite the safe design of the residential generator, operating •

this equipment imprudently, neglecting its maintenance or being

careless could cause possible injury or death.

Remain alert at all times while working on this equipment. •

Never work on the equipment when you are physically or

mentally fatigued.

Before performing any maintenance on the generator, disconnect •

the battery cable indicated by a NEGATIVE, NEG or (-) first. When

finished, reconnect that cable last.

After your system is installed, the generator may crank and start •

without warning any time there is a power failure. To prevent

possible injury, always set the generator’s system switch to OFF,

remove the service disconnect from the disconnect box AND

remove the 15 Amp fuse BEFORE working on the equipment.

WARNING Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or

explosion resulting in death, serious injury and/or

property damage.

Install the fuel supply system according to NFPA 37 and other •

applicable fuel-gas codes.

Before placing the generator into service, the fuel system lines •

must be properly purged and leak tested.

After the generator is installed, you should inspect the fuel •

system periodically.

NO leakage is permitted.•

DO NOT operate engine if smell of fuel is present or other •

explosive conditions exist.

DO NOT smoke around the generator. Wipe up any oil spills •

immediately. Ensure that no combustible materials are left in the

generator compartment. Keep the area near the generator clean

and free of debris.

WARNING Hazardous Voltage - Contact with power lines could

cause electric shock or burn, resulting in death or

serious injury.

Lifting Hazard / Heavy Object - Could result in

serious injury.

If lifting or hoisting equipment is used, DO NOT contact any •

power lines.

DO NOT lift or move generator without assistance.•

DO NOT lift unit by roof as damage to generator will occur.•

Not for

Reproduction

6

WARNING Exhaust heat/gases could ignite combustibles or

structures resulting in death, serious injury and/or

property damage.

Contact with muffler area could cause burns

resulting in serious injury.

DO NOT touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

DO NOT install the generator closer than 5 feet (1.5m) from any •

combustibles or structures with combustible walls having a fire

resistance rating of less than 1 hour.

Keep at least minimum distances shown in • General Location

Guidelines to insure for proper generator cooling and

maintenance clearances.

It is a violation of California Public Resource Code, Section 4442, •

to use or operate the engine on any forest-covered, brush-

covered, or grass-covered land unless the exhaust system is

equipped with a spark arrester, as defined in Section 4442,

maintained in effective working order. Other states or federal

jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer to

obtain a spark arrester designed for the exhaust system installed

on this engine.

Replacement parts must be the same and installed in the same •

position as the original parts.

WARNING Starter and other rotating parts could entangle

hands, hair, clothing, or accessories resulting in

serious injury.

NEVER operate generator without protective housings, covers, or •

guards in place.

DO NOT wear loose clothing, jewelry or anything that could be •

caught in the starter or other rotating parts.

Tie up long hair and remove jewelry.•

Before servicing, remove 15 Amp fuse from control panel and •

disconnect Negative (NEG or -) battery cable.

CAUTION Installing the 15A fuse could cause the engine

to start at any time without warning resulting in minor or

moderate injury.

Observe that the 15 Amp fuse has been removed from the control •

panel for shipping.

DO NOT install this fuse until all plumbing and wiring has been •

completed and inspected.

CAUTION Excessively high operating speeds could result in

minor injury and/or equipment damage.

Excessively low speeds impose a heavy load on generator.

DO NOT tamper with governed speed. Generator supplies correct •

rated frequency and voltage when running at governed speed.

DO NOT modify generator in any way.•

NOTICE Improper treatment of generator could damage it and

shorten its life.

Use generator only for intended uses.•

If you have questions about intended use, contact your •

authorized dealer.

Operate generator only on level surfaces.•

Adequate, unobstructed flow of cooling and ventilating air is •

critical to correct generator operation.

The access panels/door must be installed whenever the unit •

is running.

DO NOT expose generator to excessive moisture, dust, dirt, or •

corrosive vapors.

Remain alert at all times while working on this equipment. •

Never work on the equipment when you are physically or

mentally fatigued.

DO NOT start engine with air cleaner or air cleaner cover removed.•

DO NOT insert any objects through cooling slots.•

DO NOT use the generator or any of its parts as a step. Stepping •

on the unit could cause stress and break parts. This may result in

dangerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc.

If connected devices overheat, turn them off and disconnect them •

from generator.

Shut off generator if: •

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

NOTICE Exceeding generators wattage/amperage capacity could

damage generator and/or electrical devices connected to it.

Start generator and let engine stabilize before connecting •

electrical loads.

Not for

Reproduction

7

 • Readandfollowtheinstructionsgiveninthe

operator’s manual,

 • Followaregularscheduleinmaintaining,caringfor

and using your home generator, as specified in the

operator’s manual.

Home Owner Responsibilities

If operating the generator below 40°F (5°C), it is HIGHLY

RECOMMENDED that a battery warmer be installed. This item

is available at your local servicing dealer. It is also HIGHLY

RECOMMENDED that the higher capacity colder climate

battery be installed. See Battery Specificaionstable under

“Final Installation Considerations”.

If you need more information on this matter, please call

(888) 575-8226, between 8:00 AM and 5:00 PM CT.

 • Readandobservethesafetyrules.

 • InstallonlyanULapprovedtransferswitchthatis

compatible with the generator.

 • Readandfollowtheinstructionsgiveninthis

installation and start-up manual.

Installing Dealer/Contractor Responsibilities

The unit is shipped bolted to its mounting pad, ready for

installation. Avoid damage from dropping, bumping, collision,

etc. Store and unpack carton with the proper side up, as

noted on the shipping carton.

Unpacking Precautions

Installation

This product is intended for use as an optional home

generator system which provides an alternate source

of electric power and to serve loads such as heating,

refrigeration systems, and communication systems that,

when stopped during any power outage, could cause

discomfort or inconvenience. This product does not qualify

for emergency standby as defined by NFPA 70 (NEC).

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

Only current licensed electrical and plumbing professionals

should attempt home generator system installations.

Installations must strictly comply with all applicable codes,

industry standards and regulations.

Not for

Reproduction

8

After removing the carton, carefully inspect the generator for

any damage that may have occurred during shipment.

If loss or damage is noted at time of delivery, have the

person(s) making delivery note all damage on the freight bill

and affix his signature under the consignor’s memo of loss or

damage. If loss or damage is noted after delivery, separate

the damaged materials and contact the carrier for claim

procedures. Missing or damaged parts are not warranted.

Delivery Inspection

The home generator system is supplied with:

 • Pre-attachedmountingpad

 • Fully-servicedoil/lubricatingsystem

 • Flexiblefuelhook-uphose

 • Installationandstart-upmanual

 • Operator’smanual

 • Engineoperator’smanual

 • Installationchecklist

 • Accessdoorkeys

 • Spare15AmpATO-typefuse

 • Two-polecontrolpanelconnector

 • Ten-polecontrolpanelconnector

 • Oildraintray

 • Touchuppaint

 • Roofhardware

 • Fuelconversionkit

Not supplied:

 • Startingbattery(seepage19)

 • Connectingwireandconduit

 • Fuelsupplyvalves/plumbing

 • Crane,liftingstraps,chainsorcables

 • Holepunchesfor16gasteel

 • Torquescrewdriver,5to50inch-poundrange

 • Voltage/frequencymeter

Shipment Contents

Before installing the generator, consult with the homeowner

and convey the following guidelines, which may affect the

desired installation location.

Generator Location

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

Operate this product ONLY outdoors.•

Install a battery operated carbon monoxide alarm near •

the bedrooms.

Keep exhaust gas from entering a confined area through •

windows, doors, ventilation intakes, or other openings.

WARNING Exhaust heat/gases could ignite combustibles

or structures resulting in death, serious injury and/or

property damage.

DO NOT install the generator closer than 5 feet (1.5m) from any •

combustibles or structures with combustible walls having a fire

resistance rating of less than 1 hour.

Not for

Reproduction

9

A Non-Combustible material with Fire Resistant Rating of

1 hour or greater

B Home Standby Generator

C Engine Exhaust

D Combustible Material or Structure with a Fire

Resistance Rating of less than 1 hour.

E Any structure or material. DO NOT connect (A) and/or

(D) to (E).

Install generator outdoors in an area which will not

accumulate deadly exhaust gas. DO NOT install generator

where exhaust gas could accumulate and enter inside or be

drawn into a potentially occupied building. Ensure exhaust

gas is kept away from windows, doors, ventilation intakes

or other openings that can allow exhaust gas to collect in a

confined area. Prevailing winds and air currents should be

taken into consideration when positioning generator.

General Location Guidelines

 • InstalltheunitoutdoorsONLY.

 • Placetheunitinapreparedlocationthatisflatand

has provisions for water drainage.

 • Installtheunitinalocationwheresumppump

discharge, rain gutter down spouts, roof run-off,

landscape irrigation, or water sprinklers will not flood

the unit or spray the enclosure and enter any air inlet

or outlet openings.

 • Installtheunitwhereitwillnotaffectorobstruct

any services (including covered, concealed and

underground), such as telephone, electric, fuel,

irrigation, air conditioning, and so forth.

 • Installtheunitwhereairinletandoutletopenings

will not become obstructed by leaves, grass, snow,

etc. If prevailing winds will cause blowing or drifting,

you may need to construct a windbreak to protect

the unit.

 • Installthegeneratorascloseaspossibletothe

transfer switch and fuel supply to reduce the length of

wiring, conduit, and piping.

Laws or local codes may regulate the distance to the

fuel supply.

The minimum clearances from aerial view of generator (B) to

combustible (D), and non-combustible (A) materials is shown

at right:

 • Thesedistancesareprovidedtogivegenerator

location guidance relative ONLY to combustibles,

generator cooling, and maintenance.

 • Theminimumdistancesinthefigureareasshown.

All four sides of the generator cannot be enclosed

or restricted, even if the minimum distances are

maintained. DO NOT connect (A) and/or (D) to (E)

 • Aroofcannotbeused.

 • Exhaust(C) must not be allowed to accumulate.

C

D A

B

E

5’ (1.5 m)

3’ (1 m)

5’ (1.5 m)

Not for

Reproduction

10

Electrical and Fuel Inlet Locations

The 3/4 inch N.P.T. fuel inlet connector (A) and electrical inlet

location (B) is shown at right.

The home generator is shipped already attached to its

mounting pad. Unless mandated by local code, a concrete

slab is not required.

If mandated by local code, construct a concrete slab at least

3 inches thick and 6 inches longer and wider than the unit.

Attach unit to slab with 1/4” diameter (minimum) masonry

anchor bolts long enough to retain the unit.

A

B

Lifting the Generator

The generator weighs more than 340 pounds (155 kg). Proper

tools, equipment and qualified personnel should be used in

all phases of handling and moving the generator.

Lifting pockets are provided at each corner between the

base of the generator and its mounting pad. Retouch any

chipped paint with supplied touch-up paint.

WARNING Hazardous Voltage - Contact with power lines could

cause electric shock or burn, resulting in death or

serious injury.

Lifting Hazard / Heavy Object - Could result in

serious injury.

If lifting or hoisting equipment is used, DO NOT contact any •

power lines.

DO NOT lift or move generator without assistance.•

DO NOT lift unit by roof as damage to generator will occur.•

Not for

Reproduction

11

The home generator is equipped with several access

openings and a removable roof to permit simple oil and

filter servicing.

To remove roof:

Remove the four screws and lift off. Replace roof in

reverse order.

To remove access cover:

Remove the two screws, tilt cover out, and lift cover off

panel. Replace cover in reverse order.

To remove side panel (if necessary):

1. Remove roof.

2. Remove screw(s) attaching side panel.

3. Pull panel outward (away) from unit while pulling

panel upward and out of base.

To install side panel:

1. Guide bottom of side into base.

2. Push panel until it is flush with sides.

3. Replace panel screw(s).

4. Replace roof and screws.

Access Ports

Each home generator is suppied with a set of identical keys.

These keys fit the locks that secure the access door.

To open access door:

1. Insert key into lock of access door and turn key one

quarter turn counterclockwise.

2. Grasp door’s handle and turn one quarter turn

counterclockwise to open. Remove key.

To close access door:

1. Close door and turn doors handle one quarter of a

turn clockwise.

2. Insert key into lock of access door and turn key one

quarter turn clockwise. Remove key.

WARNING Contact with muffler area could cause burns

resulting in serious injury.

DO NOT touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

Not for

Reproduction

12

The information below is provided to assist gaseous fuel

system technicians in planning installations. In no way

should this information be interpreted to conflict with

applicable fuel gas codes. Consult with your local fuel

supplier or Fire Marshall if questions or problems arise.

TO THE INSTALLER: Consult with the generator owner(s) and

convey any technical considerations that might affect their

installation plans before applying these general guidelines.

The following general rules apply to gaseous fuel

system piping:

 • Thepipingshouldbeofamaterialthatconforms

to federal and local codes, rigidly mounted and

protected against vibration.

 • Pipingshouldbeprotectedfromphysicaldamage

where it passes through flower beds, shrub beds, and

other cultivated areas where damage could occur.

The Gaseous Fuel System

 • Installtheflexible,gaseoushose(B) (supplied)

between the generator fuel inlet port (A) and rigid

piping to prevent thermal expansion or contraction

from causing excessive stress on the piping material.

 • Aunion(C) or flanged connection shall be provided

downstream to permit removal of controls.

 • Amanometerportshouldbeprovided(D). A digital

manometer,P/N19495,isavailableatyourBriggs&

Stratton service center. When the initial test runs are

completed, the manometer is removed and the port

is plugged. The manometer port permits temporary

installation of a manometer to ensure that the

engine receives the correct fuel pressure to operate

efficiently throughout its operating range.

 • Wheretheformationofhydratesoriceisknownto

occur, piping should be protected against freezing.

The termination of hard piping should include a

sediment trap (E) where condensate is not likely to

freeze.

 • Aminimumofoneaccessible,approvedmanual

shutoff valve (F) shall be installed in the fuel supply

line within 6 ft (180 cm) of the home generator.

 • Aminimum10ft.(3m)sectionofgaspipebetween

the primary fuel regulator and the generator fuel inlet

connection (acts as accumulator for high block loads).

WARNING Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or

explosion resulting in death, serious injury and/or

property damage.

LP gas is heavier than air and will settle in low areas.•

Natural gas is lighter than air and will collect in high areas.•

The slightest spark could ignite these fuels and cause an explosion.•

DO NOT light a cigarette or smoke.•

NOTICE The supplied flexible gaseous pipe is not to be installed

underground or in contact with the ground.

The entire flexible gaseous pipe must be visible for periodic •

inspection and must not be concealed within nor contact nor run

through any wall, floor, or partition.

WARNING Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or

explosion resulting in death, serious injury and/or

property damage.

Before placing the generator into service, the fuel system lines •

must be properly purged and leak tested.

No leakage is permitted.•

A

B

C

E

D

F

Not for

Reproduction

13

Fuel Pressure

Both LP vapor and natural gas fuel supply pressure at the

generator’s fuel inlet port should be between 7 to 11 inches

(18 to 28 cm) of water (in. W.C.) at full load with all gas

appliances turned on and operating. Maximum pressure with

engine OFF at No Load is 13.85 psi.

Power Loss

Air density is less at high altitudes, resulting in less available

engine power. Specifically, engine power will decrease 3.5%

for each 1,000 feet (300 m) above sea level and 1% for each

10° F (5.6°C) above 77°F (25°C). Generators located in these

conditions must have their transfer switch programmed

appropriately for this power decrease.

Fuel Pipe Sizing

There are numerous on-line or otherwise-published

references for fuel pipe sizing. For example, NFPA 54 -

National Fuel Gas Code, 2006 (Item #: 320-6031-06) is a

common resource.

The installer should consider the specific gravity of gas

and compensate for a nominal amount of restriction from

bends, fittings, etc. If an unusual number of fittings, bends, or

other restrictions are used, refer to federal and local codes

for guidance.

 • Amanualfuelshut-offvalvelocatedintheinteriorof

the building.

 • Wherelocalconditionsincludeearthquake,

tornado, unstable ground, or flood hazards, special

consideration shall be given to increase strength and

flexibility of piping supports and connections.

 • Pipingmustbeofthecorrectsizetomaintainthe

required supply pressures and volume flow under

varying generator load conditions with all gas

appliances connected to the fuel system turned on

and operating.

 • Useapipesealantorjointcompoundapprovedfor

use with NG/LPG on all threaded fittings to reduce the

possibility of leakage.

 • Installedpipingmustbeproperlypurgedand

leak tested, in accordance with applicable codes

and standards.

The generator has been factory set to run on natural gas. If

you need to change from natural gas to LP gas, the unit will

need to be reconfigured, as described in Fuel Conversion.

It is recommended that the fuel connection incorporate the

following components:

 • Amanualfuelshut-offvalvelocatedintheinteriorof

the building.

 • Amanualfuelshut-offvalvelocatedoutsidethe

building, just before the generator unit.

 • Wheretheformationofhydratesoriceisknownto

occur, piping should be protected against freezing.

The termination of hard piping should include

a sediment trap where condensate is not likely

to freeze.

 • Amanometerportshouldbeprovided.

The manometer port permits temporary installation of

a manometer to ensure that the engine receives the

correct fuel pressure to operate efficiently throughout its

operating range.

When the initial test runs are completed, the manometer

is removed and the port is plugged. A typical final fuel

connection assembly is shown here, where (A) is the fuel

supply and (B) goes to the home generator.

Not for

Reproduction

14

Fuel Consumption

Estimated fuel supply requirements at half and full load for

natural gas and LP vapor fuels are shown here.

Natural Gas LP Vapor

1/2 Load Full Load 1/2 Load Full Load

80 C 137 C 33 C 56 C

80,000 B 137,000 B 82,500 B 140,000 B

C = Cubic feet per hour

B = BTU’s per hour

Physical

Properties

LP Vapor Natural

Gas

Normal Atmospheric

State

Gas Gas

Boiling Point (in °F):

Initial

End

-44

-259

Heating Value:

BTU per gallon (Net

LHV*)

BTU per gallon (gross**)

Cubic feet (gas)

83,340

91,547

2,500

63,310

1,000

Density*** 36.39 57.75

Weight† 4.24 2.65

Octane Number:

Research

Motor

110+

97

110+

* LHV (Low Heat Value) is the more realistic rating.

** Gross heat value does not consider heat lost in the form of water during

combustion.

*** Density is given in “Cubic Feet of Gas per Gallon of Liquid”.

† Weight is given in “Pounds per Gallon of Liquid”.

Not for

Reproduction

15

Low Voltage connections to signal fault contacts, transfer switch communication, remote LED and auxiliary 12VDC power are

made via a removable ten-pole connector plug. Compare this illustration with your generator to familiarize yourself with the

location of these connections. Count down to the proper pin location on the control board since visual alignment with the decal

can be misleading:

System Connectors

A - Fault Contacts—UseNO,COMandNCtohookupa

siren, light, etc. to alert you in case of a fault. Contacts

reverse state (NO goes to NC and vice versa) upon a

fault condition.

B - Transfer Switch Communication—Connecttotransfer

switch control board for communication interface using

18AWG copper twisted pair wire.

C - Remote LED Output—Usethistohookuptheremote

LED supplied with the generator. The remote LED will

turn on and off in a series of blinks if certain faults are

detected in the generator.

D - +12 Volt DC, .5 Amp Output—Internalpowersupplyfor

installer supplied, optional accessories.

E - 240 Volt Utility—Usetohookupthe240Vutilityleads

from the transfer switch to the generator.

F – Ten-pole Connector Plug

G – Two-pole Connector Plug

 • Forpoweroutputconnection,use#10AWGminimum300volt75°C-90°Ccopperwire,(ref.NECTable310.16,100ft.

Use National Electric Code for correction factors and wire size calculations.)

 • ForUtilityCircuitconnectionuse#14AWGminimum300volt75°C-90°Ccopperwire

 • Fortransferswitchcommunicationuse#18AWGtwistedpairconductors,nogreaterthan200ftinlength,300volt

75°C-90°Ccopperwire

 • Whenconnectingtotheconnectorplugs,fastenonlyonewiretoeachconnectorscrew.

 • Torqueconnectorplugscrewsto7in-lb(7.9Newtonmeter).

C E

D

A

B

F

G

Not for

Reproduction

16

Generator AC Connection System

A single-phase, three-wire AC connection system is used in

the home generator. The stator assembly consists of a pair

of stationary windings with two leads brought out of each

winding. The junction of leads 22 and 33 forms the neutral

lead, as shown schematically and as a wiring diagram. A

complete schematic and wiring diagram can be found later

in this manual.

Neutral is not bonded to ground at generator.

33

240V

11

22

44

120V

1122 33 44 0

Neutral

Power Winding

Circuit

Breaker

Line 1

Neutral

To Transfer Switch

Line 2 Ground

Circuit

Breaker

Ground the home generator per applicable codes, standards,

and regulations. The generator GND lug is located inside the

control panel box.

Grounding the Generator

Not for

Reproduction

17

Fault Detection System

The generator may have to run for long periods of time with

no operator present. For that reason, the system is equipped

with sensors that automatically shut down the generator

in the event of potentially damaging conditions, such as

low oil pressure, high temperature, over speed, and other

conditions. Refer to Fault Detection System in the operator’s

manual for more detailed information.

The owner will use the remote LED indicator to observe

the status of the home generator system. The remote LED

will turn on and off in a series of blinks if certain faults are

detected in the generator system. Consult with the owner

for a convenient location. Locate the electrical box in an

area visible by the home owner such as near a garage door

opener or security control panel.

To install the remote LED indicator:

1. Push the LED through the mounting plate from

the front until it snaps in place. The LED is

polarity sensitive.

2. Using provided 10 pole connector and installer-

supplied minimum 18AWG wire, connect the remote

LED to the generator control board +LED and GND

connection. Use wire nuts to attach wire to LED leads.

3. Attach mounting plate to installer-supplied

electrical box.

Utility Circuit Connection

“240V Utility” leads must be routed in conduit. The “240V

Utility” leads deliver power to the generator’s circuit board,

optional battery warmer and optional oil warmer. This power

also charges the battery. When power on these leads is lost,

the generator will start.

Using provided 2 pole connector plug and installer-supplied

minimum 300V, 14 AWG copper wire, connect each control

circuit terminal in the generator to the two-amp fuse

terminals in the automatic transfer switch.

When making connections, obey wire type and torque

specifications printed on the circuit breaker and neutral/

ground connector.

A

B

Transfer Switch Communication

(Units with ACCM II or later transfer switch only)

Using #18 AWG twisted pair conductors, no greater than

200 t in length, connect Tx Rx and Tx Rx GND from the

generator control panel (A) to T/R and GNDon the transfer

switch control board (B).

Not for

Reproduction

18

System Control Panel

The home generator control panel, located inside the

generator housing, is shown below.

Brief descriptions of the controls used during installation are:

A - Set Exercise —Usedtosettheexercisecycle.

B - Circuit Breaker —MustbeON to supply power to the

transfer switch.

C - 15 Amp Fuse—ProtectsDCcontrolcircuits.

D - System Switch—SwitchesmodestoOFF or AUTO.

E – MANUAL OVER-RIDE—Usedtomanuallystartandstop

the generator.

F - Digital Display—Displaysrunningtimeinhoursor

fault codes.

More information may be found in Controls in the

operator’s manual.

System Switch

This two-position switch is the most important control on the

home generator and is used as follows:

 • “AUTO” position is the normal operating position. If a

utility power outage is sensed, the system will start

the generator. When utility power is restored, lets the

engine stabilize internal temperatures, shuts off the

generator, and waits for the next utility power outage.

 • “OFF” position turns off running generator, prevents

unit from starting and resets any detected faults.

15 Amp Fuse

Protects the home generator DC control circuits. If the fuse

has ‘blown’ (melted open) or was removed, the engine cannot

crank or start. Replace the fuse using only an identical

ATO 15A fuse. One spare fuse is supplied with the unit. If fuse

was blown or removed, you will need to reset the exercise

timer (see Setting Exercise Timer).

A

D

B

EC F

Not for

Reproduction

19

Fuel Supply System

Ensure that all fuel pipe connections are tight, secure and

without leaks.

Ensure that all gas line shutoff valves are OPEN and that

adequate fuel pressure is available whenever automatic

operation is desired.

Engine Oil

This engine is shipped from the factory pre-run and filled with

synthetic oil (SAE 5W-30). This allows for system operation in

a wide range of temperature and climate conditions. Before

starting the engine, check oil level and ensure that engine is

serviced as described in the engine operator’s manual.

The use of synthetic oil does not alter the required oil change

intervals described in the engine operator’s manual.

Final Installation Considerations

Battery

The installer must supply and install a valve-regulated

rechargeable 12 volt starting battery. The starting battery

MUST conform to the specifications shown in these charts.

It is also HIGHLY RECOMMENDED to use a higher capacity

battery in colder climates.

Battery Specifications (Warm Climate)

Volts 12 Volt DC

Amps (MIN) 350 CCA (cold cranking amps)

Type AGM

Terminal Hardware M8

Dimensions (MAX):

Width 5.325 inches (135mm)

Length 7.875 inches (200mm)

Height 6.875 inches (175mm)

Battery Specifications (Colder Climate)

Volts 12 Volt DC

Amps (MIN) 600 CCA (cold cranking amps)

Type AGM

Terminal Hardware M8

Dimensions (MAX):

Width 5.43 inches (138mm)

Length 9.02inches(229mm)

Height 8.19inches(208mm)

Install the battery as descriInstall the battery as described

in Servicing the Battery in the Maintenance section of the

operator’s manual. Always make sure the NEGATIVE cable is

connected last and that the red POSITIVE terminal insulator

is fully in place.

NOTICE Any attempt to crank or start the engine before it has

been properly serviced with the recommended oil will result in

equipment failure.

Refer to • Maintenance in the operator’s manual and engine

manual for oil fill information.

Damage to equipment resulting from failure to follow this •

instruction will void engine and generator warranty.

WARNING Battery posts, terminals and related accessories

contain lead and lead compounds, chemicals known to the State

of California to cause cancer and reproductive harm. Wash hands

after handling.

Not for

Reproduction

20

Initial Start-up (No Load)

Before operating the home generator or placing it into

service, inspect the entire installation carefully. Then begin

testing the system without any electrical loads connected,

as follows:

Unit has been set-up for NG operation at the factory. Fuel

conversion, if needed, must be completed prior to performing

these steps. See Fuel Conversion later in this section.

1. Remove four screws that secure control panel to

enclosure to expose unit’s circuit breaker.

2. Connect an accurate frequency meter to line side of

generator’s main circuit breaker.

3. Set generator’s main circuit breaker to ON

(closed) position.

4. Install 15 Amp fuse in control panel.

5. Set generator’s system switch to AUTO.

6. Push and hold MANUAL OVER-RIDE button on control

panel for about six seconds. Engine will start.

When the generator is started for the very first time, it will

require that air in the gaseous fuel lines be purged. This may

take a few minutes.

7. Listen for unusual noises, vibration or other

indications of abnormal operation. Check for oil leaks

while engine runs.

8. Let engine warm up for about five minutes to allow

internal temperatures to stabilize.

 9. Checkgeneratoroutputatloadsideofcircuitbreaker.

Voltageshouldbe239-262Volts,frequencyshould

be 62.0 - 62.5 Hz.

If either parameter is outside these ranges, perform Engine

Adjustment described later in this section.

10. Check generator output between one generator

connection lug and neutral lug, then between

other generator connection lug and neutral lug.

In both cases, voltage reading should be between

119and131Volts.

DO NOT proceed until you are certain that generator AC

voltage and frequency are correct and within the stated

limits. To obtain the proper generator frequency, see

Engine Adjustment.

11. Push and hold MANUAL OVER-RIDE button on

control panel until engine stops.

12. Reinstall control panel into enclosure.

Not for

Reproduction

La page charge ...

General Electric 040315A-0 Le manuel du propriétaire

Ce manuel convient également à

General Electric 040315A-0 Le manuel du propriétaire

dans d''autres langues

Autres documents