Generac 3100 PSI 006692R0 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
www.generac.com or 1-888-436-3722
Operator's Manual
Power Washer
Introduction ............................................................. 1
Safety Rules ...........................................................1
Safety Symbols and Meanings .......................................1
General Information ................................................ 4
Know Your Power Washer .........................................................4
Product Specifications ..............................................................5
Emissions Information ..............................................................5
High Altitude Operation ..............................................................5
Unpacking .................................................................................6
Set-up ..................................................................... 6
Assembly ..................................................................................6
Add Engine Oil ..........................................................................7
Add Fuel ...................................................................................7
Connect Hose and Water Supply to Pump .................................8
How to Use Nozzles ..................................................................9
Cleaning and Applying Detergent ..................................10
Power Washer Rinsing .................................................11
Cleaning Detergent Siphoning Tube ...............................11
Operation .............................................................. 12
Operation ................................................................................12
Power Washer Location ..........................................................12
Checklist Before Starting Engine ..............................................12
How to Start Your Power Washer ............................................12
Automatic Cool Down System (Thermal Relief) .......................14
How to Stop Your Power Washer .............................................14
Maintenance ......................................................... 14
Maintenance Recommendations ..............................................14
Maintenance Schedule ............................................................15
Pump Oil .................................................................................15
Emissions Control ...................................................................15
Power Washer Maintenance ....................................................15
Check and Clean Inlet Screen ..................................................15
Check High Pressure Hoses ....................................................15
Check Detergent Siphoning Tube .............................................15
Check Spray Gun ....................................................................15
Nozzle Maintenance ................................................................15
Engine Maintenance ................................................................16
Engine Oil Recommendations ..................................................16
Check Oil Level ............................................................17
Adding Engine Oil .........................................................17
Changing Engine Oil .....................................................17
Service Air Cleaner .................................................................18
Service Spark Plug ..................................................................18
Inspect Muffler and Spark Arrestor ..........................................18
Remove Spark Arrester Screen .....................................18
After Each Use ........................................................................19
Winter Storage ........................................................................19
Long Term Storage..................................................................20
Protect Fuel System .....................................................20
Protect Engine ..............................................................20
Change Oil ...................................................................20
Protecting the Pump .....................................................20
Other Storage Instructions .......................................................20
Transporting/Tipping of the Unit ..............................................20
Troubleshooting .................................................... 21
Troubleshooting Guide .............................................................21
Manuel del propietario.......................................... 23
Manuel d'entretien ................................................ 47
Table of Contents
INTRODUCTION
Thank you for purchasing this power washer manufactured by
Generac Power Systems, Inc. This model is a high performance,
air-cooled, engine-driven power washer that operates between
2500 and 3100 psi depending on which model you purchased.
The units feature custom designed wheels, axial cam pump
with stainless steel pistons, automatic cool down system, quick
connect nozzles, high pressure hose, detergent siphoning hose
and chemical tank(s) depending on unit model.
Common sense and strict compliance with the special instructions
are essential to preventing accidents. The operator must read
this manual and thoroughly understand all of the instructions
and warnings before using the equipment. If any portion of the
manual is not understood, contact the nearest Authorized Dealer
for starting, operating and servicing procedures. The owner is
responsible for proper and safe use of the equipment.
The power washer can operate safely, efficiently and reliably only if
it is properly located, operated and maintained. Before operating,
servicing or storing:
• Study all warnings in this manual and on the product carefully.
• Become familiar with this manual and the unit before use.
• Refer to the Assembly section of the manual for instructions on
final assembly procedures. Follow the instructions completely.
The manufacturer cannot anticipate every possible circumstance
that might involve a hazard. The warnings in this manual, and on
tags and decals affixed to the unit are, therefore, not all inclusive.
If using a procedure, work method or operating technique that the
manufacturer does not specifically recommend, ensure that it is
safe for others. Also make sure the procedure, work method or
operating technique utilized does not render the power washer
unsafe.
THE INFORMATION CONTAINED HEREIN WAS BASED ON
MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.
GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT
ANY TIME.
Save these instructions for future reference. If you loan this
device to someone, ALWAYS loan these instructions AND the
Owner's Manual to the individual as well.
WHERE TO FIND US
You can contact Generac Customer Service by phone at 1-888-
436-3722, or on the internet at www.generac.com. Record the
important information of the unit in the following chart for future
reference and/or service inquiries.
Model Number
Serial Number
Date Purchased
SAFETY RULES
Throughout this publication, and on tags and decals affixed to
the power washer, DANGER, WARNING, CAUTION and NOTE
blocks are used to alert personnel to special instructions about
a particular operation that may be hazardous if performed
incorrectly or carelessly. Observe them carefully. Their definitions
are as follows:
Indicates a hazardous situation or action which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation or action which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation or action which, if not avoided,
could result in minor or moderate injury.
NOTE:
Notes contain additional information important to a procedure
and will be found within the regular text body of this manual.
These safety warnings cannot eliminate the hazards that they
indicate. Common sense and strict compliance with the special
instructions while performing the action or service are essential to
preventing accidents.
SAFETY SYMBOLS AND MEANINGS
KickbackToxic Fumes Electrical Shock
Fluid InjectionFall
Fire Explosion Operator’s Manual
Slippery Surface
Moving Parts Flying Objects Hot Surface
1
Introduction
2
DANGER: Carbon monoxide produced during use CAN KILL
in minutes. NEVER use indoors, in a vehicle, or in other
sheltered areas, EVEN IF doors and windows are open. Only
use OUTSIDE and far away from windows, doors and vents.
Some chemicals or detergents may be harmful if inhaled
or ingested, causing severe nausea, fainting, or poisoning.
• Operate power washer ONLY outdoors.
• A running engine gives off carbon monoxide.
• Carbon monoxide is an odorless, colorless, poisonous gas.
Breathing carbon monoxide can cause headache, fatigue,
dizziness, vomiting, confusion, seizures, nausea, fainting
or death. If you start experiencing any of these symptoms,
IMMEDIATELY move to fresh air. Seek medical attention.
• Keep exhaust gas from entering a confined area through
windows, doors, ventilation intakes, or other openings. Warn any
occupants inside about the symptoms of carbon monoxide so
they know to move to fresh air if they begin to feel ill.
• The use of a carbon monoxide detector inside any occupied
premises between the power washer and the occupant is
recommended.
• NEVER start or run engine indoors, in a vehicle, or in an
enclosed area, EVEN IF windows and doors are open.
• Use a respirator or mask whenever there is a chance that
harmful gas or vapors may be inhaled.
• Read all instructions with respirator or mask so you are certain
the respirator or mask will provide the necessary protection
against inhaling harmful gas or vapors. If you begin to
experience any of the CO symptoms listed above, IMMEDIATELY
move to fresh air.
DANGER: NEVER aim spray gun at people, animals, or
electrical devices. Serious injury or death will result.
ALWAYS point spray gun in safe direction, squeeze spray gun
trigger to release high pressure, every time you stop engine.
Engage trigger lock when not in use.
• The high pressure stream of water that this equipment
produces can cut through skin and its underlying tissues,
leading to serious injury, possible amputation or death.
Spray gun traps high water pressure, EVEN WHEN engine
is stopped and water is disconnected, which can cause
injury.
• NEVER allow CHILDREN to operate power washer or play nearby.
This is NOT a toy.
• NEVER repair high pressure hose. Replace it.
• NEVER repair leaking connections with sealant of any kind.
Replace o-ring or seal.
• NEVER connect high pressure hose to nozzle extension.
• Keep high pressure hose connected to pump and spray gun
while system is pressurized.
• NEVER secure spray gun in open position.
• NEVER leave spray gun unattended while machine is running.
• NEVER use a spray gun which does not have a trigger lock or
trigger guard in place and in working order.
• ALWAYS be certain spray gun, nozzles and accessories are
correctly attached.
WARNING: Risk of electrocution.
Contact with power source can cause electric shock or
burn.
• NEVER spray near power source.
WARNING: Contact with muffler area can result in serious
burns. Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least five (5) feet (152 cm) of clearance on all
sides of power washer including overhead.
• It is a violation of California Public Resource Code, Section
4442, to use or operate the engine on any forest-covered,
brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in
Section 4442, maintained in effective working order. Other
states or federal jurisdictions may have similar laws.
Contact the original equipment manufacturer, retailer, or dealer to
obtain a spark arrester designed for the exhaust system installed
on this engine.
• Replacement parts must be the same and installed in the same
position as the original parts.
WARNING: Fuel and its vapors are extremely flammable and
explosive. Fire or explosion can cause severe burns or death.
WHEN ADDING OR DRAINING FUEL
• Turn power washer OFF and let it cool at least two (2)
minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
• Fill or drain fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting
engine.
• Keep fuel away from sparks, open flames, pilot lights, heat, and
other ignition sources.
• DO NOT light a cigarette or smoke.
WHEN STARTING EQUIPMENT
• Ensure spark plug, muffler, fuel cap, and air cleaner are in place.
• DO NOT crank engine with spark plug removed.
WHEN OPERATING EQUIPMENT
• DO NOT tip engine or equipment at angle which causes fuel to
spill.
• DO NOT spray flammable liquids.
WHEN TRANSPORTING OR REPAIRING EQUIPMENT
• Transport/repair with fuel tank EMPTY or with fuel shutoff valve
OFF.
• Disconnect spark plug wire.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK
• Store away from furnaces, stoves, water heaters, clothes dryers,
or other appliances that have pilot light or other ignition source
because they can ignite fuel vapors.
Safety Rules
3
WARNING: Use of power washer can create puddles and
slippery surfaces. Kickback from spray gun can cause you to
fall.
• Use only on a level surface.
• The cleaning area should have adequate slopes and
drainage to reduce the possibility of a fall due to slippery
surfaces.
• Do not use on elevated surfaces where chance of kickback
could result in a serious fall.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
WARNING: Starter and other rotating parts can
entangle hands, hair, clothing, or accessories.
• NEVER operate power washer without protective housing
or covers.
• DO NOT wear loose clothing, jewelry or anything that
may be caught in the starter or other rotating parts.
• Tie up long hair and remove jewelry.
WARNING: Starter cord kickback (rapid retraction) can result
in bodily injury. Kickback will pull hand and arm toward
engine faster than you can let go. Broken bones, fractures,
bruises, or sprains could result.
• NEVER pull starter cord without first relieving spray gun
pressure.
• To relieve trapped pressure, point gun in safe direction and
release pressure by pulling/actuating trigger on spray gun.
• When starting engine, pull cord slowly until resistance is felt and
then pull rapidly to avoid kickback.
• After each starting attempt, where engine fails to run, always
point spray gun in safe direction, and squeeze spray gun trigger
to release high pressure.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
WARNING: Unintentional sparking can result in fire or electric
shock.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR POWER
WASHER.
• Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
WARNING: Risk of eye injury. Spray can splash back or
propel objects.
• Always wear safety goggles when using this equipment or
in vicinity of where equipment is in use.
• Before starting the power washer, be sure you are
wearing adequate safety goggles.
• NEVER substitute safety glasses for safety goggles.
WARNING: The engine exhaust from this product contains
chemicals known to the State of California to cause cancer,
birth defects, or other reproductive harm.
WARNING: This product contains lead and lead compounds,
known to the State of California to cause birth defects or
other reproductive harm. Wash your hands after handling this
product.
NOTE:
High pressure spray may damage fragile items including
glass.
• DO NOT point spray gun at glass when using red (0°) MAX
nozzle.
• NEVER aim spray gun at people, animals, electrical devices or
plants.
NOTE:
Improper treatment of power washer can damage it and
shorten its life.
• If you have questions about intended use, ask dealer or contact
qualified service center.
• NEVER operate units with broken or missing parts, or without
protective housing or covers.
• DO NOT by-pass any safety device on this machine.
• DO NOT operate power washer above rated pressure.
• DO NOT modify power washer in any way.
• Before starting power washer in cold weather, check all parts of
the equipment to be sure ice has not formed there.
• NEVER move machine by pulling on hoses. Use handle provided
on unit.
• Check fuel system for leaks or signs of deterioration, such as
chafed or spongy hose, loose or missing clamps, or damaged
tank or cap. Correct all defects before operating power washer.
• This equipment is designed to be used with Generac authorized
parts ONLY. If equipment is used with parts that DO NOT
comply with minimum specifications, user assumes all risks
and liabilities.
Safety Rules
CALIFORNIA PROPOSITION 65 WARNING
Engine exhaust and some of its constituents are known
to the State of California to cause cancer, birth defects
and other reproductive harm.
CALIFORNIA PROPOSITION 65 WARNING
This product contains or emits chemicals known to the
State of California to cause cancer, birth defects and
other reproductive harm.
4
KNOW YOUR POWER WASHER
Read this owner’s manual and safety rules before operating your
high power washer.
If you loan this device to someone, ALWAYS loan these instructions
AND the owner’s manual to the individual as well. Compare the
illustrations with your high power washer to familiarize yourself
with the locations of various controls (Figure 1). Save this manual
for future reference. Replacement owner’s manuals can be printed
from the Generac Web site.
A - Spray Gun – Controls the application of water onto the cleaning
surface with trigger device. Includes a trigger lock.
B - Lance with Quick Connect – Allows you to switch between different
nozzles.
C - High Pressure Hose – Connect one end to water pump and the other
to the spray gun.
D - Recoil Starter – Use for starting the engine.
E - Oil Fill – Check and add engine oil.
F - Air Filter – Protects engine by filtering dust and debris out of the
intake air.
G - Pump – Develops high pressure.
H - Thermal Relief Valve – Cycles water through the pump when water
reaches 125°F warm water will discharge from pump onto ground.
This prevents internal pump damage.
I - Engine On/Off Switch – Turn this switch to “ON” before using the
recoil starter. Turn the switch to “OFF” to stop the engine.
J - Unloader Valve – Controls the high pressure output.
K - High Pressure Outlet – Connection for high pressure hose.
L - Water Inlet – Connection for Garden Hose.
M - Fuel Tank – Fill tank with regular unleaded fuel. Always leave room
for fuel expansion.
N - Fuel On/Off Switch – Turns fuel supply to the engine on and off.
O - Choke – Prepares a cold engine for starting.
P - Throttle Lever – Increases or decreases engine speed. Throttle
should be at maximum travel when the power washer is in use.
Q - Nozzles – Chemical injection, 0°, 15°, 25°, 40° for various high
pressure cleaning applications.
R - Chemical Tank – Used to hold power washer safe detergents to
be siphoned into the low pressure stream. (some units may not be
equipped with tanks or may only have one tank).
S - Warning/Operation Instruction – Identifies proper procedure to
start/stop power washer.
T - Drain Plug – Used to drain engine oil.
U - Serial Number Location
ITEMS NOT SHOWN
• Identification Label (on engine blower housing) – Provides model and
serial number of power washer. Please have these readily available if
calling for assistance.
• Detergent Siphoning Tube/Filter – Use to siphon power washer safe
detergents into the low pressure stream.
General Information
A
C
J
K
L
H
G
T
I
Q
M
D
B
P
O
N
R
F
S
E
U
Figure 1 – Features & Controls
5
General Information
PRODUCT SPECIFICATIONS
CONSUMER
Pressure - (PSI / BAR) 2500/172 2700/186 3100/213
Flow Rate - (GPM / LPM) 2.3/8.7 2.7/10.2
Water supply temperature - (°F / C°) 100/38 Max
Hose length - (Feet / Meters) 25/7.6 25/7.6 30/9.1
Chemical Tank(s) - Number per unit 0 1 2
Chemical Tank - Capacity (Gallon - Liters) N/A 0.75/2.8 0.75/2.8
Nozzles - Number per unit 3 4 5
Lance Length (Inches / cm) 20/51
Gun Standard Deluxe
Engine Displacement - (Cubic Inch / cc) 11.9/196 12.9/212
Spark Plug Type F7TC or equivalent
Spark Plug Gap - (Inches / mm) 0.028-0.031/0.70-0.80
Fuel Capacity - (Quarts / Liters) 3.7/3.5
Oil Capacity - (Oz / Liters) 20/0.6
Low Oil Shut Down System Yes
On/Off Switch Yes
EMISSIONS INFORMATION
The U.S. Environmental Protection Agency (and California Air
Resource Board for equipment certified to CA standards) requires
that this engine comply with exhaust and evaporative emission
standards. Locate the emissions compliance decal on the engine
to determine what standards the engine meets, and to determine
which emissions warranty applies. The engine is certified to meet
the applicable emission standards on gasoline. It is important to
follow the maintenance specifications in the Maintenance section
to ensure that the engine complies with the applicable emission
standards for the duration of the product’s life. This engine utilizes
lean carburetion settings and other systems to reduce emissions.
Tampering with or altering the emission control system may
increase emissions and may be a violation of Federal or California
Law. Acts that constitute tampering include but are not limited to:
• Removal or alteration of any part of the intake, fuel, or exhaust
systems
• Altering or defeating the governor linkage or speed-adjusting
mechanism to cause the engine to operate outside its design
parameters
If you are aware of any of the following symptoms, have your
engine inspected and repaired by your servicing dealer:
• Hard starting or stalling after starting
• Rough idle
• Misfiring or backfiring under load
• Afterburning (backfiring)
• Black exhaust smoke or high fuel consumption
HIGH ALTITUDE OPERATION
The fuel system on this engine may be influenced by operation at
higher altitudes. Proper operation can be ensured by installing an
altitude kit when required. See the table below to determine when
an altitude kit is required. Operating this engine without the proper
altitude kit installed may increase the engine’s emissions and
decrease fuel economy and performance. Kits may be obtained
from any Dealer, and should be installed by a qualified individual.
Altitude* Kit Number PSI
0 - 5000 Feet Not Required 2500/2700/3100
5000 - 7000 Feet 0K2015 2500/2700
5000 - 7000 Feet 0K2016 3100
*Elevation above sea level.
NOTE:
If the altitude kit has been installed and the engine will be
operated at an altitude where the kit is not required, the
engine should be returned to the original factory configuration.
Operating the engine at lower altitudes with the kit installed
may cause the engine to overheat and result in serious engine
damage, and may result in decreased performance and
increased emissions.
6
Set-up
UNPACKING
1. Remove the parts bag, accessories, and inserts included with
power washer.
2. Open carton completely by cutting each corner from top to
bottom.
3. Ensure you have all included items prior to assembly.
• Main Unit
• Handle Assembly
• High Pressure Hose
• Siphon Hose & Filter
• Spray Gun
• Lance with Quick Connect Fitting
• Oil Bottle
• Hose Hook Wireform
• Parts Bag (which includes the following):
– Chemical Tank Cap with hole if model is equipped with a
Chemical Tank
– Operator’s Manual
– Owner’s Registration Card
– Bag containing Color-coded Nozzles
4. If you are missing any items from your carton, please call
Generac Customer Service at 1-888-436-3722. When calling
for assistance, please have the model and serial number from
the data tag available.
5. Fill out and send in registration card. Write Model number,
Serial number & date of purchase in the table located in the
"Where to Find Us" section.
ASSEMBLY
Read entire operator’s manual before you attempt to assemble or If
you have any problems with the assembly of your power washer,
please call Generac Customer Service at 1-888-436-3722. When
calling for assistance, please have the model and serial number
from the data tag available.
1. Place handle (A) onto handle supports (B). Push in latch
buttons and allow handle to slide into position (C). Button will
lock handle into place (Figure 2).
Figure 2 – Attach Handle
NOTE:
It may be necessary to move the handle supports from side to
side in order to align the handle so it will slide over the handle
supports.
2. Install hose hook (Figure 3).
Figure 3 – Install Hose Hook
3. Insert color–colored nozzles in spaces provided in handle
(Figure 4).
4. Place spray gun and nozzle extension into spray gun holder as
shown (Figure 4).
5. Coil high pressure hose and hang on hook.
Figure 4 – Insert Nozzles
7
Set-up
6. Attach siphon tube to location A (Figure 5).
Figure 5 – Siphon Tube Location
A
ADD ENGINE OIL
1. Place power washer on a flat, level surface.
2. Clean area around oil fill and remove orange oil fill cap/
dipstick.
3. Using oil funnel (optional), slowly pour oil into fill opening. See
Maintenance section for oil type recommendation.
NOTE:
On some units there is more than one oil fill location. In these
instances it is only necessary to use one of the oil fill points.
4. Check periodically until the oil level is between "L" and "H" on
the dipstick (Figure 6). DO NOT OVERFILL.
Figure 6 – Dipstick
Acceptable Oil
Level Range
NOTE:
Any attempt to crank or start the engine before it has been
properly serviced with the recommend oil may result in engine
failure.
5. Replace oil fill cap/dipstick and fully tighten.
ADD FUEL
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON).
• Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTE:
Avoid power washer damage. Failure to follow Operator’s
Manual for fuel recommendations voids warranty.
• DO NOT use unapproved gasoline such as E85.
• DO NOT mix oil in gasoline.
• DO NOT modify engine to run on alternate fuels.
To protect the fuel system from gelling, mix in a fuel stabilizer when
adding fuel. See Storage. All fuel is not the same. If you experience
starting or performance problems after using fuel, switch to a
different fuel provider or change brands.
Fuel and its vapors are extremely flammable
and explosive. Fire or explosion can cause
severe burns or death.
WHEN ADDING FUEL
• Turn power washer OFF and let it cool at least two (2) minutes
before removing fuel cap. Loosen cap slowly to relieve pressure in
tank.
• Fill fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting engine.
• Keep fuel away from sparks, open flames, pilot lights, heat, and
other ignition sources.
• DO NOT light a cigarette or smoke.
1. Clean area around fuel fill cap, remove cap.
2. Slowly add regular unleaded fuel to fuel tank. Be careful not
to overfill. Fill to bottom of filter screen, this will allow for fuel
expansion (Figure 7).
3. Install fuel cap and let any spilled fuel evaporate before
starting engine.
Figure 7 – Adding Fuel
8
CONNECT HOSE AND WATER SUPPLY TO PUMP
NOTE:
DO NOT run the pump without the water supply connected
and turned on. Damage to equipment resulting from failure to
follow this instruction will void warranty.
NOTE:
Remove and discard the shipping cap from the pump’s water
inlet before attaching hose.
1. Run water through your garden hose for 30 seconds to clean
out any debris.
2. Before connecting garden hose to water inlet, inspect inlet
screen (A) (Figure 8). Clean screen if it contains debris or
have it replaced if damaged. DO NOT run power washer if inlet
screen is damaged.
IMPORTANT: DO NOT siphon standing water for the water supply.
Use ONLY cold water (less than 100°F). Water supply must be
adequate to handle greater than 3.8 gallons per minute and no less
than 30 psi.
NOTE:
Using a One Way Valve (vacuum breaker or check valve) at
pump inlet can cause pump or inlet connector damage.
• There MUST be at least ten feet of unrestricted garden hose
between the power washer inlet and any device, such as a
vacuum breaker or check valve.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
Figure 8 – Inspect Inlet Screen
A
3. Connect the garden hose (not to exceed 50 feet in length) to
the water inlet (Figure 9). Tighten by hand.
Figure 9 – Connect Garden Hose
Risk of eye injury. Spray can splash back or propel
objects.
• Always wear safety goggles when using this equipment or in
vicinity of equipment in use.
• Before starting the power washer, be sure you are wearing
adequate safety goggles.
• NEVER substitute safety glasses for safety goggles.
4. Connect lance to spray gun (Figure 10). Tighten by hand.
Figure 10 – Attach Lance
5. Attach end of high pressure hose to base of spray gun (Figure
11). Tighten by hand.
Figure 11 – Connect Hose to Spray Gun
Set-up
9
The high pressure stream of water that this equipment
produces can cut through skin and its underlying
tissues, leading to serious injury and possible
amputation.
• NEVER connect high pressure hose to lance.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
• Always be certain spray gun, nozzles and accessories are
correctly attached.
6. Connect high pressure hose to pump (uncoil hose before
connecting to pump or spray gun) (Figure 12). Tighten by
hand.
The hose can be damaged if it comes in contact with a
hot engine or muffler.
Figure 12 – Connect High Pressure Hose to Pump
7. Turn ON the water, squeeze the trigger to purge the pump
system of air (Figure 13).
Figure 13 – Squeeze Trigger
HOW TO USE NOZZLES
The quick–connect on the nozzle lance allows you to switch
between different nozzles. Nozzles can be changed while power
washer is running once spray gun trigger is locked in the safety
position. The nozzles vary the pressure and spray pattern as
shown.
• For most effective cleaning, keep nozzle from 8 to 24 inches (20
to 61 cm) away from cleaning surface.
• If you get nozzle too close, especially using a high pressure
nozzle, you may damage surface being cleaned.
The high pressure stream of water that this equipment
produces can cut through skin and its underlying
tissues, leading to serious injury and possible
amputation.
• NEVER exchange nozzles without the trigger lock being engaged on
the spray gun.
• DO NOT twist nozzles while spraying.
Follow these instructions to change nozzles:
1. Pull back collar on quick–connect and pull current nozzles
off. Store nozzles in holder provided on the accessory storage
(Figure 14).
Figure 14 – Nozzles
2. Select desired nozzle.
3. Pull back on collar, insert new nozzle and release collar. Tug
on nozzle to make sure it is securely in place.
• For delicate rinse (lower pressure and higher flow), for gentle
cleaning of cars/trucks, boats, RV’s, patio furniture, lawn
equipment, etc., select white nozzle (Figure 15).
Figure 15 – Wash Pressure Nozzle (White)
Set-up
10
• For general rinsing (medium pressure and medium flow), ideal for
most all purpose cleaning such as home siding, brick patios, wood
decks, driveways and sidewalks, garage floors, etc., select green
nozzle (Figure 16).
Figure 16 – Clean Pressure Nozzle (Green)
• For medium rinsing (higher pressure and medium flow), ideal
for removing stains on hard porous surfaces such as concrete
dirveways, garage floors and brick patios, select yellow nozzle
(Figure 17).
Figure 17 – Strip Pressure Nozzle (Yellow)
• For maximum rinsing (higher pressure and lower flow), for
stubborn or hard to reach surface such as second story surfaces,
paint removal, oil stains, rust removal or other stubborn substances
(tar, gum, grease, wax, etc.), select red nozzle (Figure 18).
This tip (Red Nozzle) can damage work surface if it is
too close or held in one position for an extended time.
Figure 18 – Blast Pressure Nozzle (Red)
• When applying detergent, use only the black nozzle (Figure 19).
Only use power washer safe detergents/soaps to help break down
stubborn dirt and grime on a variety of surfaces.
Figure 19 – Detergent Nozzle (Black)
CLEANING AND APPLYING DETERGENT
Chemicals can cause bodily injury, and/or property
damage.
• NEVER use caustic liquid with power washer.
• Use ONLY power washer safe detergents/soaps. Follow all
manufacturer's instructions.
To apply detergent, follow these steps:
1. Review use of nozzles.
2. Open container cap (if so equipped, Figure 20).
3. Prepare detergent solution as required by job.
Figure 20 – Chemical Tank & Cover
Container
Cap
4. Depending on model, insert filter on end of siphoning tube
through the hole in the loose cap (supplied) (Figure 21).
5. Install cap and siphoning tube onto tank.
6. Make sure siphoning tube remains fully submerged into
detergent.
Set-up
11
Figure 21 – Install Siphoning Tube
NOTE:
Make sure the filter remains fully submerged in detergent
while applying detergent.
NOTE:
Contact with the hot muffler can damage detergent siphoning
tube.
• When inserting the siphon into a detergent solution bottle, route the
tube so as to keep it from inadvertently contacting the hot muffler.
7. Make sure black detergent nozzle is installed.
NOTE:
Detergent cannot be applied with the high pressure nozzle
(Yellow, White, Green or Red). Only use the Black nozzle with
detergent.
8. Confirm set-up instructions have been followed.
NOTE:
You must attach all hoses before you start the engine.
• Starting the engine without all the hoses connected and without the
water turned ON will damage the pump.
• Damage to equipment resulting from failure to follow this instruction
will void warranty.
9. Start engine following instructions How to Start Your Power
Washer.
10. Apply detergent to a dry surface, starting at lower portion
of area to be washed and work upward using long, even,
overlapping strokes.
11. Allow detergent to "soak in" for 3-5 minutes before washing
and rinsing. Reapply as needed to prevent surface from
drying. DO NOT allow detergent to dry on surface being
cleaned (prevents streaking).
IMPORTANT: You must flush the detergent siphoning system after
each use by placing the filter into a bucket of clean water, then run
the power washer in low pressure for 1-2 minutes.
POWER WASHER RINSING
1. Remove black detergent nozzle from lance.
2. Select and install desired high pressure nozzle following
instructions How to Use Nozzles.
3. Point spray gun in safe direction and away from people,
animals and plants. Squeeze trigger to flush any remaining
chemical from system.
4. Keep spray gun a safe distance from area you plan to spray.
Kickback from spray gun can cause you to fall.
• Use only on a level surface.
• Do not use on elevated surface to prevent the risk
of a serious fall.
• Be extremely careful if you must use the power washer from a
ladder, scaffolding, or any other similar location.
• Firmly grasp spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
5. Apply a high pressure spray to a small area and then check
surface for damage. If no damage is found, you can assume
it is okay to continue rinsing.
6. Start at top of area to be rinsed, working down with same
overlapping strokes as you used for cleaning.
CLEANING DETERGENT SIPHONING TUBE
If you used the detergent siphoning tube, you must flush it with
clean water before stopping the engine.
1. Place detergent siphoning tube/filter in a bucket full of clean
water.
2. Remove high pressure nozzle from nozzle extension.
3. Select and install black detergent nozzle following instructions
How to Use Nozzles.
4. Flush for 1-2 minutes.
5. Shut off engine following instructions How to Stop Power
Washer and turn off water supply.
6. ALWAYS point spray gun in a safe direction, squeeze spray
gun trigger to release retained high water pressure. Engage
trigger lock when not in use.
IMPORTANT: Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.
The high pressure stream of water that this equipment
produces can cut through skin and its underlying
tissues, leading to serious injury and possible
amputation. Spray gun traps high water pressure, even
when engine is stopped and water is disconnected,
which can cause injury.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
• ALWAYS point spray gun in safe direction, and squeeze spray
gun trigger to release high pressure, every time you stop engine.
Engage trigger lock when not in use.
Operation
12
OPERATION
If you have any problems operating your power washer, please call
Generac customer service at 1-888-436-3722.
POWER WASHER LOCATION
Clearances and Air Movement
Running engine gives off carbon monoxide, an
odorless, colorless, poisonous gas. Breathing carbon
monoxide can cause headache, fatigue, dizziness,
vomiting, confusion, seizures, nausea, fainting or
death. For more information, reference the CO
warnings in the Safety Rules section.
Place power washer outdoors in an area that will not accumulate
deadly exhaust gas. NEVER place power washer where exhaust
gas could accumulate and enter inside or be drawn into a
potentially occupied building. Ensure exhaust gas is kept away
from any windows, doors, ventilation intakes, or other openings
that can allow exhaust gas to collect in a confined area. Prevailing
winds and air currents should be taken into consideration when
positioning power washer (Figure 22).
• Operate power washer ONLY outdoors.
• Keep exhaust gas from entering a confined area through windows,
doors, ventilation intakes, or other openings.
• NEVER start or run engine indoors, in a vehicle or in an enclosed
area, EVEN IF windows and doors are open.
Exhaust heat/gases can ignite combustibles,
structures or damage fuel tank causing a fire.
• Keep at least 5 ft. (152 cm) clearance on all sides of power washer
including overhead.
Figure 22 – Building Clearances
5 Foot Minimum
CHECKLIST BEFORE STARTING ENGINE
1. Be sure to read and understand the Operator Safety section
and Operation section before using power washer.
2. Check that oil is at the proper level in the engine crankcase and
that fuel has been added to the fuel tank.
3. Review the unit's assembly and ensure fitting are properly
secured and make sure there are no kinks, cuts, or damage to
high pressure hose.
4. Provide a proper water supply at an adequate flow, clear
screens of debris, and confirm that the system is purged of air.
5. Confirm unit is secure on level ground and surrounding work
area is clear.
HOW TO START YOUR POWER WASHER
NOTE:
DO NOT run the pump without the water supply connected
and turned on. Damage to equipment resulting from failure to
follow this instruction will void warranty.
1. Move the fuel valve lever to the ON position (Figure 23).
Figure 23 – Fuel Valve
Off
On
2. Move choke lever to “CLOSE” position (Figure 24).
NOTE:
For a warm engine, be sure the choke lever is in the “OPEN”
position.
Figure 24 – Choke Lever
Choke
Close
Open
Operation
13
3. Move throttle control lever to “HIGH” position, shown on
engine as a rabbit (Figure 25).
Figure 25 – Throttle Control
High Low
4. Turn the engine switch to the "ON" position (Figure 26).
Figure 26 – The ON Position
OFF
ON
IMPORTANT: Before starting the power washer, be sure you are
wearing adequate safety goggles.
Risk of eye injury. Spray can splash back or propel
objects.
• Always wear safety goggles when using this equipment or in
vicinity of equipment in use.
• Before starting the power washer, be sure you are wearing
adequate safety goggles.
• NEVER substitute safety glasses for safety goggles.
5. Place foot on footpad or otherwise secure unit from movement
when pulling recoil.
6. When starting the engine, grasp starter grip handle (Figure
27) and pull slowly until you feel some resistance. Then pull
rapidly to start engine.
Figure 27 – Starting the Engine
Starter Handle
Starter cord kickback (rapid retraction) can result in
bodily injury. Kickback will pull hand and arm toward
engine faster than you can let go. Broken bones,
fractures, bruises, or sprains could result.
• NEVER pull starter cord without first relieving spray gun pressure.
• When starting engine, pull cord slowly until resistance is felt and
then pull rapidly to avoid kickback.
• After each starting attempt, where engine fails to run, always point
spray gun in safe direction and squeeze spray gun trigger to release
high pressure.
• Firmly grasp spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
7. Return starter grip handle slowly. DO NOT let rope “snap back”
against starter.
8. When engine starts, slowly move choke lever to “OPEN”
position as engine warms. If engine falters, move choke lever
to “CLOSE” position, then to “OPEN” position (Figure 28).
Figure 28 – Choke Lever
Choke
Open
9. After each starting attempt, where engine fails to run, always
point gun in safe direction, and squeeze spray gun trigger to
release high pressure.
10. If engine fails to start after six pulls, move choke lever to
“OPEN” position, and repeat steps 6 through 10.
Operation
14
The high pressure stream of water that this equipment
produces can cut through skin and its underlying
tissues, leading to serious injury and possible
amputation. Spray gun traps high water pressure, even
when engine is stopped and water is disconnected,
which can cause injury.
• DO NOT allow CHILDREN to operate power washer or play nearby.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
• NEVER aim spray gun at people, animals or electrical devices.
Serious injury will result.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is running.
• NEVER use a spray gun which does not have a trigger lock or
trigger guard in place and in working order.
• Always be certain spray gun, nozzles and accessories are
correctly attached.
Contact with muffler area can result in serious
burns. Exhaust heat/gases can ignite
combustibles, structures or damage fuel tank
causing a fire.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 feet (152 cm) of clearance on all sides of power
washer including overhead.
• It is a violation of California Public Resource Code, Section 4442,
to use or operate the engine on any forest-covered, brush-covered,
or grass-covered land unless the exhaust system is equipped with
a spark arrester, as defined in Section 4442, maintained in effective
working order. Other states or federal jurisdictions may have
similar laws.
• Replacement parts must be the same and installed in the same
position as the original parts.
AUTOMATIC COOL DOWN SYSTEM (THERMAL
RELIEF)
If you run the engine on your power washer for 3-5 minutes
without pressing the trigger on the spray gun, circulating water
in the pump can reach temperatures above 125°F. The system
engages to cool the pump by discharging the warm water onto
the ground.
HOW TO STOP YOUR POWER WASHER
1. Release spray gun trigger.
2. Move throttle control lever on engine to “LOW” (turtle)
position (Figure 29).
3. Turn the engine ON/OFF switch to the "OFF" position.
4. ALWAYS point spray gun in a safe direction, and squeeze
spray gun trigger to release retained high water pressure.
Engage trigger lock when not in use.
5. Turn OFF water supply.
Figure 29 – Throttle Position
High Low
IMPORTANT: Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.
The high pressure stream of water that this equipment
produces can cut through skin and its underlying
tissues, leading to serious injury and possible
amputation. Spray gun traps high water pressure, even
when engine is stopped and water is disconnected,
which can cause injury.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
• ALWAYS point spray gun in safe direction, squeeze spray gun
trigger to release high pressure, every time you stop engine.
Engage trigger lock when not in use.
MAINTENANCE RECOMMENDATIONS
Regular maintenance will improve the performance and extend
the life of the power washer. See any qualified dealer for service.
The power washer’s warranty does not cover items that have been
subjected to operator abuse or negligence. To receive full value
from the warranty, the operator must maintain the power washer
as instructed in this manual, including proper storage as detailed
in Winter Storage and Long Term Storage.
NOTE:
Should you have questions about replacing components
on your power washer, please call 1-888-436-3722 for
assistance.
Some adjustments will need to be made periodically to properly
maintain your power washer.
All service and adjustments should be made at least once each
season. Follow the requirements in the Maintenance Schedule
chart.
NOTE:
Once a year you should clean or replace the spark plug, clean
or replace the air filter, and check the spray gun and nozzle
extension assembly for wear. A new spark plug and clean air
filter assure proper fuel-air mixture and help your engine run
better and last longer.
Maintenance
15
MAINTENANCE SCHEDULE
Follow the hourly or calendar intervals, whichever occurs first.
More frequent service is required when operating in adverse
conditions.
First 5 Hours
Change engine oil
Every 8 Hours or Daily
Check/clean water inlet screen*
Check high pressure hose
Check detergent siphoning hose/filter
Check spray gun and assembly for leaks
Clean debris
Check engine oil level
Every 20 Hours or Every Season
Change engine oil**
Every 50 Hours or Every Season
Check/clean air cleaner filter**
Inspect muffler and spark arrester*
Every 100 Hours or Every Season
Service spark plug
* Clean if clogged. Replace if perforated or torn.
** Service more often under dirty or dusty conditions.
PUMP OIL
DO NOT attempt any oil maintenance on this pump. The pump is
pre-lubricated and sealed from the factory, requiring no additional
maintenance for the life of the pump.
EMISSIONS CONTROL
Maintenance, replacement, or repair of the emissions control
devices and systems may be performed by any non-road engine
repair establishment or individual. However, to obtain ”no
charge” emissions control service, the work must be performed
by a factory authorized dealer. See the Emissions Warranty.
POWER WASHER MAINTENANCE
Clean Debris
Daily or before use, clean accumulated debris from cleaning
system. Keep linkage, spring and controls clean. Keep area
around and behind muffler free from any combustible debris.
Inspect cooling air slots and openings on the power washer. These
openings must be kept clean and unobstructed.
Power washer parts should be kept clean to reduce the risk of
overheating and ignition of accumulated debris.
• Use a damp cloth to wipe exterior surfaces clean.
NOTE:
Improper treatment of power washer can damage it and
shorten its life.
• DO NOT insert any objects through cooling slots.
• Use a soft bristle brush to loosen caked on dirt, oil, etc.
• Use a vacuum cleaner to pick up loose dirt and debris.
CHECK AND CLEAN INLET SCREEN
Examine the screen on the pump’s water inlet. Clean it if the screen
is clogged or replace it if screen is damaged.
CHECK HIGH PRESSURE HOSES
The high pressure hoses can develop leaks from wear, kinking, or
abuse. Inspect the hoses each time before using them. Check for
cuts, leaks, abrasions or bulging of cover, damage or movement
of couplings. If any of these conditions exist, replace the hose
immediately.
The high pressure stream of water that this equipment
produces can cut through skin and its underlying
tissues, leading to serious injury and possible
amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST meet or exceed maximum
pressure rating of unit.
CHECK DETERGENT SIPHONING TUBE
Examine the filter on the detergent tube and clean if clogged. The
tube should fit tightly on the barbed fitting. Examine the tube for
leaks or tears. Replace the filter or tube if either is damaged.
CHECK SPRAY GUN
Examine the hose connection to the spray gun and make sure it is
secure. Test the trigger by pressing the trigger, it “springs back”
into place when you release it. Replace spray gun immediately if
it fails to "spring back".
NOZZLE MAINTENANCE
A pulsing sensation felt while squeezing the spray gun trigger
may be caused by excessive pump pressure. The principal cause
of excessive pump pressure is a nozzle clogged or restricted
with foreign materials, such as dirt, etc. To correct the problem,
immediately clean the nozzle following these instructions:
1. Shut off engine and turn off water supply.
2. ALWAYS point spray gun in a safe direction, squeeze spray
gun trigger to release retained high water pressure.
Maintenance
16
The high pressure stream of water that this equipment
produces can cut through skin and its underlying
tissues, leading to serious injury and possible
amputation. Spray gun traps high water pressure, even
when engine is stopped and water is disconnected,
which can cause injury.
• Keep high pressure hose connected to pump and spray gun while
system is pressurized.
• ALWAYS point spray gun in safe direction, and squeeze spray gun
trigger to release high pressure every time you stop engine. Engage
trigger lock when not in use.
3. Remove nozzle from end of nozzle extension.
4. Use a small paper clip to free any foreign material clogging or
restricting nozzle (Figure 30).
Figure 30 – Free Foreign Material
5. Remove lance from spray gun.
6. Using a garden hose, remove additional debris by back
flushing water through lance (Figure 31). Back flush between
30 to 60 seconds.
7. Reinstall nozzle into lance.
8. Reconnect lance to spray gun.
Figure 31 – Back Flush Lance
9. Make sure garden hose is connected to pump water inlet.
Check that high pressure hose is connected to spray gun and
pump. Turn on water.
10. Start engine following instructions How to Start Your Power
Washer.
11. Test power washer by operating with each quick connect
nozzle.
ENGINE MAINTENANCE
Unintentional sparking can result in fire or
electric shock.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR POWER
WASHER
• Disconnect the spark plug wire from the spark plug and place the
wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
ENGINE OIL RECOMMENDATIONS
We recommend the use of high-quality detergent oils acceptable if
classified for service SF, SG, SH, SJ or higher. DO NOT use special
additives.
Outdoor temperatures determine the proper oil viscosity for the
engine. Use the chart to select the best viscosity for the outdoor
temperature range expected.
SAE 30*
SA E 30 *
10W-30**
10 W- 30 * *
5W-30
5W -3 0
* Below 50°F (10°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W30 may cause increased oil consumption.
Check oil level more frequently.
NOTE:
Synthetic oil meeting ILSAC GF-2, API certification mark
and API service symbol with “SJ/CF ENERGY CONSERVING”
or higher, is an acceptable oil at all temperatures. Use of
synthetic oil does not alter required oil change intervals.
NOTE:
The engine is equipped with an "Oil Alert System". This
system will automatically stop the engine before the oil level
falls below a safe limit. To avoid the inconvenience of an
unexpected shutdown, always check the engine oil level before
startup.
Maintenance
17
CHECK OIL LEVEL
Oil level should be checked prior to each use or at least every 8
hours of operation. Keep oil level maintained.
1. Make sure power washer is on a level surface.
2. Clean area around oil fill and wipe dipstick clean remove oil fill
cap (Figure 32).
3. Verify oil is at the proper level on the dipstick.
4. Insert the dipstick into filler neck but do not screw it in.
5. Replace and tighten oil fill cap.
Figure 32 – Fill Engine Oil
ADDING ENGINE OIL
1. Make sure power washer is on a flat, level surface.
2. Check oil level as described in Checking Oil Level.
3. If needed, slowly pour oil into oil fill opening until the proper
level on the dipstick is reached.
4. Insert the dipstick into filler neck but do not screw it in.
5. If level is low, fill until the oil level is between "L" and "H" on the
dipstick (Figure 33).
6. Replace and tighten oil fill cap.
Figure33 – Dipstick
Acceptable Oil
Level Range
CHANGING ENGINE OIL
If you are using your power washer under extremely dirty or dusty
conditions, or in extremely hot weather, change the oil more often.
Avoid prolonged or repeated skin contact with used
motor oil.
• Used motor oil has been shown to cause skin cancer in certain
laboratory animals.
• Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN.
• Don’t pollute. Conserve resources. Return used oil to
collection centers.
Change oil while engine is still warm from running, as follows:
1. Make sure unit is on a level surface.
2. Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.
3. Clean area around oil drain plug (A) (Figure 34). The oil drain
plug is located at base of engine, opposite carburetor.
4. Remove oil fill cap (Figure 32).
5. Remove oil drain plug and drain oil completely into a suitable
container.
6. Reinstall oil drain plug and tighten securely.
7. Slowly pour oil (about 20 oz.) into oil fill opening to the proper
level on the dipstick. DO NOT overfill.
8. Reinstall oil fill cap. Finger tighten cap securely.
9. Wipe up any spilled oil.
10. Properly dispose of oil in an accordance with all local
regulations.
Figure 34 – Oil Drain Plug
A
Maintenance
18
SERVICE AIR CLEANER
Your engine will not run properly and may be damaged if you run it
with a dirty air cleaner. Service more often if operating under dirty
or dusty conditions.
To service the air cleaner, follow these steps:
1. Pull on air cleaner cover latch and remove cover (Figure 35).
2. Loosen wing nut.
3. Carefully remove filter assembly.
4. Remove foam filter.
5. To clean cartridge, gently tap on a flat surface.
6. Reinstall foam filter.
7. Reinstall clean or new cartridge assembly.
8. Reinstall wing nut and tighten.
9. Install cover by snapping latch closed.
Figure 35 – Service the Air Cleaner
Air Cleaner
Cover
Paper Filter
Element
Foam Filter
Element
Gasket
Latch
SERVICE SPARK PLUG
Changing the spark plug will help your engine to start easier and
run better.
1. Clean area around spark plug.
2. Remove and inspect spark plug (Figure 36).
3. Check electrode gap with wire feeler gauge and reset
spark plug gap to recommended gap if necessary (see
Specifications).
4. Replace spark plug if electrodes are pitted, burned or
porcelain is cracked. Use the recommended replacement
plug. See Specifications.
5. Install spark plug and tighten firmly.
Figure 36 – Change the Spark Plug
SPARK PLUG
0.028-0.031
in
INSPECT MUFFLER AND SPARK ARRESTER
Inspect the muffler for cracks, corrosion, or other damage.
Remove the spark arrester, if equipped, and inspect for damage or
carbon blockage. If replacement parts are required, make sure to
use only original equipment replacement parts.
REMOVE SPARK ARRESTER SCREEN
Tools Required: 8mm Box Wrench
1. Remove heat shield from the muffler by loosening the four (4)
Bolts (A) (Figure 37).
2. Remove the spark arrester from the muffler by loosning the
two (2) Bolts (B) (Figure 38).
3. Inspect the spark arrester, replace if torn, perforated or
otherwise damaged (part number 0K1851). DO NOT USE A
DEFECTIVE SCREEN.
4. If screen is not damaged, clean it with a commercial solvent
and replace.
Figure 37 – Remove Heat Shield
A
A
Maintenance
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
Generac 3100 PSI 006692R0 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur