Electrolux ELFE4222AW Guide d'installation
- Catégorie
- Sèche-linge
- Taper
- Guide d'installation
Ce manuel convient également à
EN FRONT LOAD DRYER
FR SÉCHEUSE Á CHARGEMENT FRONTAL
ES SECADORA DE CARGA FRONTAL
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
INSTRUCCIONES DE INSTALACIÓN
136964920 May 2020
Important Safety Instructions
Definitions
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this sym-
bol to avoid possible injury or death.
Recognize Safety Symbols, Words
and Labels
Safety items throughout this manual are
labeled with a WARNING or CAUTION based
on the risk type as described below:
IMPORTANT
Indicates installation, operation, or
maintenance information which is important
but not hazard-related.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result
in death or serious injury.
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING
Please read all instructions before using this
dryer.
Table of Contents
Important Safety Instructions ................2
Installation Requirements ......................4
Installation Instructions .........................8
Reversing Door ...................................15
Accessories ........................................17
Thank you for choosing an Electrolux
Compact Ventless Dryer. This dryer operates
on a different drying principle than traditional
exhaust ducted dryers. Your new dryer is a
condensation, ventless dryer and DOES NOT
require exhaust venting that exhausts the
drying process air to the outside.
A condensation dryer works through a closed
loop circuit. The drying process air is heated
by an internal heating element, which then
passes over and through your clothes. The
moisture rich air proceeds down through a lint
filter, then through an air-air heat exchanger
that works as a condenser. The warm, wet
air is cooled by a separate secondary fan that
utilizes ambient room air. When the process
air cools down, it releases moisture that is
collected in a recovery basin at the bottom
of the appliance. The water can be either
pumped down the drain by the provided kit, or
pumped directly into a tank that needs to be
emptied after each drying cycle.
IMPORTANT
Your new dryer is a condensation, ventless
dryer and DOES NOT require exhaust
venting that exhausts the drying process air
to the outside.
8
3
2
1
6
5
7
9
11
4
10
1. Primary circuit –
drying process
air fan
2. Heating element
3. Lint filter
4. Clothes load
5. Heat exchanger
6. Secondary circuit –
ambient air fan
7. Drain water basin
8. Water tank
9. Float/pump switch
10. Water drain tube
11. Water pump
2
Important Safety Instructions
CAUTION
EXCESSIVE WEIGHT HAZARD
To avoid back or other injury, have more than
one person move or lift the dryer.
WARNING
EXPLOSION HAZARD
Do not install the dryer where gasoline or
other flammables are kept or stored. If the
dryer is installed in a garage, it must be a
minimum of 18 inches (45.7 cm) above the
floor. Failure to do so can result in death,
explosion, fire or burns.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
WARNING
For your safety the information in this manual must be followed to minimize the risk of fire or
explosion or to prevent property damage, personal injury or loss of life. Do not store or use
gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
WARNING
RISK OF FIRE
Read all the following instructions before installing and using this appliance.
• Recycle the carton and dispose of plastic bags after the dryer is unpacked. Children might
use them to play. Cartons covered with rugs, bedspreads, or plastic sheets can become
airtight chambers causing suffocation. Place all materials in a garbage container or make
materials inaccessible to children.
• Clothes dryer installation and service must be performed by a qualified installer or service
agency.
• Install the clothes dryer according to the manufacturer’s instructions and local codes.
• The electrical service to the dryer must conform with local codes and ordinances and the
latest edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian
Electrical Code CSA C22.1 part 1.
• The dryer is designed under ANSI Z21.5.1/CSA 7.1 or UL 2158 - CAN/CSA C22.2 No.
112 (latest editions) for HOME USE only. This dryer is not recommended for commercial
applications such as restaurants, beauty salons, etc.
• DO NOT stack a dryer on top of washer already installed on pedestal. DO NOT stack dryer
on top of another dryer. DO NOT stack washer on top of dryer. DO NOT stack washer on
top of another washer. DO NOT stack dryer on top of washer without use of manufacturer
approved and correctly installed stacking kit appropriate for your model.
The instructions in this manual and all other literature included with this dryer are not meant to
cover every possible condition and situation that may occur. Good safe practice and caution
MUST be applied when installing, operating and maintaining any appliance.
IMPORTANT
DO NOT INSTALL YOUR DRYER:
1. In an area exposed to dripping water or
outside weather conditions.
2. On carpet. Floor MUST be solid with a
maximum slope of 1 inch (2.5 cm).
3
Installation Requirements
Unpacking
Plastic film (lining drum interior) is removed
and discarded. See also image below.
Leveling
Dryer is level, side-to-side and front-to-
back
Cabinet is setting solid on all corners
208v/240v Electric Supply
Approved NEMA 10-30 or 14-30 service
cord with all screws tight on terminal block
Terminal access cover/strain relief installed
before initial operation
Note: Dryers operating on 208 volt power
supply will have longer drying times than
dryers operating on 240 volt power supply.
Door Reversal
Follow detailed instructions in this guide
Test hinge and latch for function
Electrical Power
House power turned on
Dryer plugged in
Final Checks
Installation Instructions and Use & Care
Guide read thoroughly
Door latches and drum tumbles when
cycle starts
Registration card sent in
Installation Checklist
Tools and Materials Needed for Installation:
Adjustable
pliers
OR
AND AND
Phillips
screwdriver
Carpenter’s level
Optional
universal
wrench
3- or 4-wire
240 volt cord kit
AND
Please Read and Save this
Guide
Thank you for choosing Electrolux, the pre-
mium brand in home appliances. These Instal-
lation Instructions are part of our commitment
to customer satisfaction and product quality
throughout the life of your new appliance.
Questions?
Toll-free telephone and online support:
U.S. :1-877-4ELECTROLUX
(1-877-435-3287)
www.electroluxappliances.com
Canada: 1-800-265-8352
www.electroluxappliances.ca
9
4
Installation Requirements
WARNING
Improper grounding of the dryer may cause
serious injury or death. Check with a licensed
electrician if you are in doubt as to whether
the appliance is properly grounded.
3-WIRE POWER SUPPLY CORD KIT
(not supplied)
The dryer MUST employ a 3-conductor power
supply cord NEMA 10-30 type SRDT rated at
240 volt AC minimum, 30 amp, with 3 open
end spade lug connectors with upturned ends
or closed loop connectors and marked for use
with clothes dryers. For 3-wire cord connec-
tion instructions see ELECTRICAL CONNEC-
TIONS FOR A 3-WIRE SYSTEM.
4-WIRE POWER SUPPLY CORD KIT
(not supplied)
The dryer MUST employ a 4-conductor power
supply cord NEMA 14-30 type SRDT or ST (as
required) rated at 240 volt AC minimum, 30
3-wire receptacle
(NEMA type 10-30R)
4-wire receptacle
(NEMA type 14-30R)
Electrical Requirements
for Electric Dryer
NOTE
Because of potentially inconsistent voltage
capabilities, the use of this dryer with power
created by gas powered generators, solar
powered generators, wind powered genera-
tors or any other generator other than the local
utility company is not recommended.
IMPORTANT
This dryer is internally grounded to neu-
tral unless it was manufactured for sale in
Canada.
Only a 4-conductor cord shall be used when
the appliance is installed in a location where
grounding through the neutral conductor is
prohibited. Grounding through the neutral
link is prohibited for: (1) new branch circuit
installations, (2) mobile homes, (3) recre-
ational vehicles, and (4) areas where local
codes do not permit grounding through the
neutral.
OUTLET RECEPTACLE - NEMA 10-30R or
NEMA 14-30R receptacle to be located so
the power supply cord is accessible when
the dryer is in the installed position.
GROUNDING CONNECTION - See
“Grounding requirements” in Electrical
Installation section.
NOTE
Dryers manufactured for sale in Canada have
factory-installed, 4-wire power supply cord
(NEMA 14-30).
CIRCUIT - Individual 30 amp. branch circuit
fused with 30 amp. time delay fuses or
circuit breakers. Use separately fused
circuits for washer and dryer. DO NOT
operate a washer and a dryer on the same
circuit.
POWER SUPPLY - 3-wire or 4-wire,
208-240 volt, single phase, 60 Hz,
Alternating Current.
amp, with 4 open end spade lug connectors
with upturned ends or closed loop connec-
tors and marked for use with clothes dryers.
For 4-wire cord connection instructions see
ELECTRICAL CONNECTIONS FOR A 4-WIRE
SYSTEM.
5
Clearance Requirements
0"
(0cm)
0"
(0cm)
0"
(0cm)
MINIMUM INSTALLATION CLEARANCES - Inches (cm)
SIDES REAR TOP FRONT
Alcove 0” (0 cm) 0” (0 cm) 0” (0 cm) n/a
Under Counter 0” (0 cm) 0” (0 cm) 0” (0 cm) n/a
Closet Installation
If installing the dryer in a closet, the closet
door must remain open while the dryer is run-
ning to allow correct air circulation. See Use &
Care Guide for more information.
Installation Requirements
Manufactured or Mobile
Home Installation
Installation MUST conform to current
Manufactured Home Construction & Safety
Standard, Title 24 CFR, Part 32-80 (formerly
the Federal Standard for Mobile Home Con-
struction and Safety, Title 24, HUD Part 280)
or Standard CAN/CSAZ240 MH.
6
Installation Requirements
Dryer Dimensions
1
Power supply cord length on Canadian dryer approximately 59 inches (150 cm).
2
Drain hose length on washer approximately 55 inches (140 cm).
3
Power supply cord length on washer approximately 59 inches (150 cm).
24" (61 cm)
43" (109 cm)
33.5"
(85 cm)
24"
(60.5 cm)
68.5"
(174 cm)
24"
(60.5 cm)
26" (66 cm)
water supply
connection on
rear of unit
power cord
on rear of
unit³
drain hose
on rear of
unit²
electrical
supply on
rear of unit¹
floor line
43" (109 cm)
to clear open door
ÀRRUOLQH
electrical
supply on
rear of unit¹
7
Installation Instructions
Electrical Installation
The following are specific requirements for
proper and safe electrical installation of your
dryer. Failure to follow these instructions can
create electrical shock and/or a fire hazard.
Grounding Requirements -
Electric Dryer (USA)
For a grounded, cord-connected dryer:
1. The dryer MUST be grounded. In the
event of a malfunction or breakdown,
grounding will reduce the risk of electrical
shock by a path of least resistance for
electrical current.
2. After purchase and installation of a 3-wire
or 4-wire power supply cord having an
equipment-grounding conductor and a
grounding plug matching the wiring sys-
tem of the location of installation, the plug
MUST be plugged into an appropriate,
copper wired receptacle that is properly
installed and grounded in accordance
with all local codes and ordinances. If in
doubt, call a licensed electrician.
3. DO NOT modify the plug you’ve installed
on this appliance. If it will not fit the outlet,
have a proper outlet installed by a
qualified electrician.
Grounding Requirements -
Electric Dryer (Canada)
For a grounded, cord-connected dryer:
1. The dryer MUST be grounded. In the
event of a malfunction or breakdown,
grounding will reduce the risk of electrical
shock by a path of least resistance for
electrical current.
2. Since your dryer is equipped with a
power supply cord having an equipment-
grounding conductor and a grounding
plug, the plug must be plugged into an
appropriate outlet that is properly installed
and grounded in accordance with all local
codes and ordinances. If in doubt, call a
licensed electrician.
3. DO NOT modify the plug provided with
this appliance. If it will not fit the outlet,
have a proper outlet installed by a quali-
fied electrician.
WARNING
ELECTRICAL SHOCK HAZARD
• This appliance MUST be properly
grounded. Electrical shock can result if
the dryer is not properly grounded. Fol-
low the instructions in this manual for
proper grounding.
• Do not use an extension cord with this
dryer. Some extension cords are not de-
signed to withstand the amounts of elec-
trical current this dryer utilizes and can
melt, creating electrical shock and/or fire
hazard. Locate the dryer within reach of
the receptacle for the length power cord
to be purchased, allowing some slack in
the cord. Refer to the pre-installation re-
quirements in this manual for the proper
power cord to be purchased.
WARNING
ELECTRICAL SHOCK HAZARD
• A U.L.-approved strain relief must be
installed onto power cord. If the strain
relief is not attached, the cord can be
pulled out of the dryer and can be cut by
any movement of the cord, resulting in
electrical shock.
• Do not use an aluminum wired recepta-
cle with a copper wired power cord and
plug (or vice versa). A chemical reaction
occurs between copper and aluminum
and can cause electrical shorts. The
proper wiring and receptacle is a copper
wired power cord with a copper wired
receptacle
.
NOTE
The electric dryer has been designed and
certified to operate at both 240V and 208V.
Drying times on a 208V power supply will,
however, be approximately 20% longer than
drying times on a 240V power supply. This is
normal and expected behavior and applies to
all drying cycles.
WARNING
ELECTRICAL SHOCK HAZARD
Improper connection of the equipment
grounding conductor can result in a risk of
electrical shock. Check with a licensed elec-
trician if you are in doubt as to whether the
appliance is properly grounded.
8
Electrical Connection
(Non-Canada) - 3-wire
Cord
3-wire receptacle
(NEMA type 10-30R)
WARNING
ELECTRICAL SHOCK HAZARD
Failure to disconnect power source before
servicing could result in personal injury or
even death.
1. Turn off power supply to outlet.
2. Remove the three screws securing the
terminal block access cover in the upper
corner on the back of the dryer.
NOTE
Terminal screws were shipped from the factory
temporarily attached inside the access cover.
Installation Instructions
NOTE
Two cords shown above with different
terminal types.
Terminal Block Access Cover
1
1
30 AMP
NEMA 10-30
Neutral (center wire)
1
1
WARNING
ELECTRICAL SHOCK HAZARD
Do not make a sharp bend or crimp wiring/
conductor at connections.
WARNING
ELECTRICAL SHOCK HAZARD
DO NOT move internal ground in a 3-wire
system.
4. Attach the remaining two power cord
outer conductors to the outer, BRASS
colored terminals on the terminal block.
Tighten both screws securely.
3. Using an UNPLUGGED, UL-approved,
30 amp. power cord, NEMA 10-30 type
SRDT, attach the neutral (center wire)
conductor to the SILVER colored center
terminal on the terminal block. Tighten the
screw securely.
Neutral Silver Terminal
3
3
Outer Brass Terminals
4
4
4
9
IMPORTANT
If moving dryer from a 4-wire system and
installing it now in a 3-wire system, move the
internal ground wire from the center terminal
back to the GREEN screw under the
terminal block.
4-wire receptacle
(NEMA type 14-30R)
Electrical Connection
(Non-Canada) - 4-Wire Cord
1. Turn off power supply to outlet.
2. Remove the three screws securing the
terminal block access cover in the upper
corner on the back of the dryer.
3. Disconnect the internal (WHITE) dryer
harness wire from the (GREEN) ground
screw next to the terminal block.
WARNING
ELECTRICAL SHOCK HAZARD
Failure to disconnect power source before
servicing could result in personal injury or
even death.
NOTE
Terminal screws were shipped from the factory
temporarily attached inside the access cover.
Installation Instructions
NOTE
Two cords shown above with different
terminal types.
5. Reinstall the terminal block access cover.
WARNING
ELECTRICAL SHOCK HAZARD
Do not operate dryer without terminal cover
in place. A correctly installed terminal block
cover also acts a qualified strain relief for the
power cord.
Ground GREEN wire
Neutral White wire
30 AMP
NEMA 14-30
1
1
2
2
Terminal block access cover
Access cover screw
1
2
DO NOT REMOVE - screw next to this text
must not be removed.
3
1
2
2
2
3
2
2
Internal ground (GREEN screw)
Internal dryer harness (WHITE wire)
1
1
10
Installation Instructions
4. Using an UNPLUGGED, UL-approved,
30 amp. power cord, NEMA 14-30 type
ST or SRDT, attach the ground (GREEN)
power cord wire to the cabinet with the
ground (GREEN) screw. Tighten the screw
securely.
5. Move the internal (WHITE) dryer harness
wire to the terminal block and attach it
along with the neutral (WHITE) power cord
wire conductor to the center, SILVER
colored terminal on the terminal block.
Tighten the screw securely.
6. Attach the RED and BLACK power cord
conductors to the outer, BRASS colored
terminals on the terminal block. Tighten
both screws securely.
Ground GREEN screw
GREEN ground wire
1
1
2
2
Neutral silver terminal
Internal WHITE harness wire
1
1
2
2
3
WHITE neutral wire
3
Brass Terminal
BLACK or RED power wire
1
2
1
2
1
2
WARNING
ELECTRICAL SHOCK HAZARD
Do not operate dryer without terminal cover
in place. A correctly installed terminal block
cover also acts a qualified strain relief for the
power cord.
WARNING
ELECTRICAL SHOCK HAZARD
Do not make a sharp bend or crimp wiring/
conductor at connections.
7. Reinstall the terminal block access cover.
11
Installation Instructions
Direct Drain Kit (on some
models)
If your model included a direct drain kit, you
may follow the instructions below to install it
on your dryer for convenient drainage of your
dryer’s condensed water.
1. Locate the red tubing and plastic fitting on
the back of the dryer.
2. With a pair of pliers, release the hose
clamp and remove the tubing from the
plastic fitting.
NOTE
If you have an Electrolux compact dryer model
number ELFE4222AW or ELFE422CAW, you
may choose to power your Electrolux compact
washer through it as shown. See illustrations.
WARNING
NOT A GENERAL USE RECEPTACLE! Only
for use with compatible Electrolux washer
models listed in this Use & Care Guide. Keep
the outlet closed if a compatible Electrolux
washer plug is not connected to the dryer.
:DVKHU
'U\HU
3RZHU
&RUG
:DVKHU
3RZHU
&RUG
'U\HU
3RZHU5HFHSWDFOH
:DOO
2XWOHW
:DVKHU
'U\HU
3RZHU
&RUG
:DVKHU
3RZHU
&RUG
:DOO
2XWOHW
'U\HU
12
5. With the plastic cable tie that came with
the kit, secure the elbow and tubes to the
plastic fitting.
6. To route the drain tube to the left of the
dryer, secure the tube with the “P” clamp
from the kit to the back of the dryer with
the cabinet screw shown below.
7. To route the drain tube to the right of the
dryer, route the tube across the back of
the dryer and snap it into the “C” clips
shown as below.
8. Install the hose hanger from the kit onto
the end of the hose and insert in drain.
IMPORTANT
Follow these guidelines for proper drain
hose installation:
1. The distance from the bottom of the
drain tube sag to the top of highest part
of drain tube should be no more than
20” (50 cm).
2. Drain tube may need to be shortened
with scissors if sag is greater than
allowed.
3. The drain height location should be
no more than 40” (100 cm) above the
bottom of the dryer feet.
Installation Instructions
4. Retrieve the clear tubing that came in the
kit and install it also onto the elbow.
MAX
20"
(50 cm)
MAX
40"
(100 cm)
3. Retrieve the 90 degree plastic elbow from
the direct drain installation kit that came with
your dryer and install it onto the red tubing.
13
Installation Instructions
General Installation
1. Use a carpenter’s level to level your dryer
front-to-back and side-to-side.
IMPORTANT
Be sure the power is off at a circuit breaker/
fuse box before plugging the power cord
into an outlet.
3. Press down on alternate corners and
sides and feel for the slightest movement.
Adjust the appropriate leg(s) so the dryer
sits solidly on the floor on ALL four legs.
Keep the leveling leg extension at a mini-
mum for best performance of the dryer.
5. Turn on the power at the circuit breaker/
fuse box.
6. Read the Use & Care Guide provided with
the dryer. It contains valuable and helpful
information that will save you time and
money.
7. If you have any questions during initial
operation, please review the “Avoid
Service Checklist” in your Use & Care
Guide before calling for service.
8. Place these instructions in a location
near the dryer for future reference.
2. Use adjustable pliers or universal appli-
ance wrench (See Accessories) to adjust
the leveling legs so the dryer is level
front-to-rear and side-to-side, and stable
corner-to-corner.
4. Plug the power cord into a grounded
outlet.
NOTE
A wiring diagram is located next to the water
container behind the left cabinet panel.
14
1
2
3
4
5
6
7
9
10
11
12
13
8
Reversing Door
1. Locate a flat work surface, such as the
top of the dryer or the floor near the dryer,
and protect it with a soft cloth or towel.
2. Open the dryer door and remove the two
hinge screws. Remove lower screw first,
then upper screw.
3. Gently place dryer door face down on flat,
covered work surface.
4. Locate the 13 screws on the inner door
ring. Remove and save these 13 screws.
5. Separate inner door ring from the rest of
the door.
6. Release the door switch striker by pulling
on the two snap hooks located on the
rear side of the inner door ring. Install the
door switch striker on the opposite
location (180 degrees from its original
position in the inner door ring). Set the
inner door ring aside.
7. Lift the inner lens and set it aside.
8. Lift and rotate the semi-circular trim piece
clockwise 90˚ from its original position
and place onto the available plastic
alignment features.
Inner
Lens
Inner
Door
Ring
15
Reversing Door
180
2
1
9. Rotate inner lens clockwise 90˚ from its
original position and place back into door
assembly.
10. Rotate the inner door ring counterclock-
wise 90˚ from its original position and
reattach with 13 screws removed earlier.
11. Gently pry the plastic latch cover from
the front panel and set it aside. Remove
the 3 screws securing the door latch and
release the latch.
12. Rotate the latch 180° and reinstall it in
the opposite location with the 3 screws
removed in previous step.
13. Rotate the plastic latch cover 180° and
snap it in place around the door latch.
14. While supporting the door, install the 2
hinge mounting screws removed in first
step. Attach the upper screw first and
then the lower one.
15. Close the door and test operation of
hinge, strike and latch.
90
2
1
3
180
2
1
3
1
2
3
4
5
6
7
9
10
11
12
13
8
16
DIRECT DRAIN KIT
P/N DK11
Depending on the model you purchased,
a direct draining kit for your condensing
dryer’s water collection system may have
been included in the initial purchase of your
dryer. If your model did not include a direct
draining kit, you may order one.
DRYER STACKING KIT
P/N STACKIT24
Depending on the model you purchased, a
kit for stacking this dryer on top of match-
ing washer may have been included in the
initial purchase of your dryer. If your model
did not include a stacking kit or you desire
another stacking kit, you may order one.
UNIVERSAL APPLIANCE WRENCH
P/N 137019200
A UNIVERSAL APPLIANCE WRENCH is
available to aid in dryer/washer feet
adjustment.
Replacement Parts:
If replacements parts are needed for your
washer, contact the source where you
purchased your washer or refer to your
Use & Care Guide for more information.
CAUTION
Failure to use accessories manufactured
by (or approved by) the manufacturer could
result in personal injury, property damage or
damage to the dryer.
Universal Appliance Wrench
WARNING
ELECTRICAL SHOCK HAZARD
Label all wires prior to disconnection when
servicing controls. Wiring errors can cause
improper and dangerous operation. Verify
proper operation after servicing.
Accessories
17
Notes
18
Notes
19
electrolux.com/shop
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
Electrolux ELFE4222AW Guide d'installation
- Catégorie
- Sèche-linge
- Taper
- Guide d'installation
- Ce manuel convient également à