GE 22, 23, 25, 27 Manuel utilisateur

Marque: GE

Modèle: 22, 23, 25, 27

Catégorie: Frigos

Taper: Manuel utilisateur

ge.com
Refrigerators
Side by Side
200D8074P016 49-60491 12-06 JR
La section française commence à la page 40
La sección en español empieza en la página 75
Safety Instructions  . . . . . . . . . . . . . . .2–3
Operating Instructions
Automatic Icemaker  . . . . . . . . . . . . . . .11
Care and Cleaning . . . . . . . . . . . . . .13, 14
Crispers and Pans  . . . . . . . . . . . . . . . . .10
ExpressChill
™
 . . . . . . . . . . . . . . . . . . . . .5
Ice and Water Dispenser . . . . . . . . .12, 13
Refrigerator Doors  . . . . . . . . . . . . . . . . .9
Replacing the Light Bulbs . . . . . . . . . . .15
Shelves and Bins  . . . . . . . . . . . . . . . . .7, 8
Temperature Controls . . . . . . . . . . . . . . .4
TurboCool
™
 . . . . . . . . . . . . . . . . . . . . . . .4
Water Filter  . . . . . . . . . . . . . . . . . . . . . . .6
Installation Instructions
Installing the Refrigerator  . . . . . . . .21–24
Moving the Refrigerator  . . . . . . . . .17–20
Preparing to Install 
the Refrigerator . . . . . . . . . . . . . . . . . . .16
Water Line Installation  . . . . . . . . . .25–27
Troubleshooting Tips  . . . . . . . . . . .28–31
Normal Operating Sounds  . . . . . . . . . .28
Consumer Support
Consumer Support  . . . . . . . . .Back Cover
Performance Data Sheet  . . . . . . . . . . . .32
Product Registration (U.S.) . . . . . . .33, 34
Product Registration (Canadian)
 . . .35, 36
State of California Water 
Treatment Device Certificate . . . . . . . . .37
Warranty (Canadian) . . . . . . . . . . . . . . .38
Warranty (U.S.)  . . . . . . . . . . . . . . . . . . .39
Réfrigérateurs
Côte à Côte
Refrigeradores
Lado a Lado
Models 22, 23, 25 and 27
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on a label inside 
the refrigerator compartment at the 
top on the right side.
Owner’s Manual 
and Installation
Manuel d’utilisation 
et d’installation
Manual del propietario 
e instalación

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet. Skin

may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

located on the bottom of the icemaker. Do

not place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■ Do not refreeze frozen foods which have

thawed completely.

NOTE: Turning the refrigerator off via the controls on

the touch panel does not shut off electrical power to the

refrigerator.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer Support

Troubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

ge.com

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous…even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the

company handling the disposal about what

to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use

of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

If the outlet is a standard 2-prong outlet, it is

your personal responsibility and obligation to

have it replaced with a properly grounded

3-prong wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on

the power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

TurboCool rapidly cools the refrigerator

compartment in order to more quickly

cool foods. Use TurboCool when adding

a large amount of food to the refrigerator

compartment, putting away foods after they

have been sitting out at room temperature

or when putting away warm leftovers. It can

also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn

on immediately and the fans will cycle on

and off at high speed as needed for eight

hours. The compressor will continue to run

until the refrigerator compartment cools to

approximately 34°F (1°C), then it will cycle on

and off to maintain this setting. After 8 hours,

or if TurboCool is pressed again, the refrigerator

compartment will return to the original setting.

How to Use

Press TurboCool. The TurboCool temperature

display will show Tc and the LED will be

activated.

After TurboCool is complete, the TurboCool

indicator light will go out.

NOTES: The refrigerator temperature cannot be

changed during TurboCool.

The freezer temperature is not affected

during TurboCool.

When opening the refrigerator door

during TurboCool, the fans will continue

to run if they have cycled on.

About the temperature controls.

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for the

freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

The temperature controls can display both the SET temperature as well as the actual temperature in the

refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on usage

and operating environment.

■ On some models, setting both controls to the warmest setting until the display flashes (off) will stop

cooling in both the freezer and refrigerator compartments.

■ On other models, setting either control to the warmest setting until the display flashes (off) will stop the

cooling to the freezer and refrigerator.

■ NOTE: Turning the refrigerator off via the controls on the touch panel does not shut off electrical power

to the refrigerator.

NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not

removed during installation, remove it now.

About TurboCool.

™

(on some models)

How it Works

Not all features are on all models. Your controls will look like one of the following:

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

The Performance Air-Flow System is

designed to maximize temperature control

in the refrigerator and freezer compartments.

This unique special feature consists of the Air

Tower along the back wall of the refrigerator

and the Air Tunnel on the bottom portion of

the freezer rear wall. Placing food in front of

the louvers on these components will not affect

performance. Although the Air Tower and

the Air Tunnel can be removed, doing so will

affect temperature performance. (For removal

instructions, on-line, 24 hours a day, contact us

at ge.com or call 800.GE.CARES. In Canada,

1.800.361.3400.)

Performance Air Flow System

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Empty the pan. Place the Chill tray in

the pan. Place the items on the tray and

close the pan completely.

Select the ExpressChill

™

pad. On some

models, you can then select the chill

time (use chart to determine best

setting). Other models will only have

one option (45 minutes). On models

with multiple settings, tap the pad until

the light appears next to the desired

setting.

■ To stop a feature before it is

finished, tap that feature’s pad

until no options are selected and

the display is off.

■ During ExpressChill, the display on

the controls will count down the time

in the cycle.

About ExpressChill

™

. (on some models) ge.com

The ExpressChill

™

feature is a system

of dampers, a fan and a temperature

thermistor.

The pan is tightly sealed to prevent the pan’s

temperature from causing temperature

fluctuations in the rest of the refrigerator.

The controls for this pan are located in the

top of the refrigerator or on the dispenser

with the temperature controls.

How to Use

How it Works

To remove:

Pull the drawer out to the stop position.

Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are in the

unlock position.

Place the sides of the drawer into the

drawer supports, making sure the swing

locks fit on the drawer slots.

Lock all four swing locks by rotating

them to the lock position.

How to Remove and Replace the Drawer

ExpressChill

™

ExpressChill

™

Chart

NOTE: Results may vary depending on packaging, starting temperature and other food traits.

15 Minutes

■ 1 Beverage Can (12 oz)

■ 2 Small Juice Boxes

(6–8 oz each)

30 Minutes

■ 2 to 6 Beverage Cans

(12 oz each)

■ 2 Plastic 20 oz Bottles

of Beverage

■ 4 to 6 Small Juice Boxes

(6–8 oz each)

■ 3 Foil Juice Packets

■ Wine (750 ml bottle)

45 Minutes

■ 2 Liters of Beverage

■ 1/2 Gallon of Juice

■ Gelatin—1 package

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

About the water filter. (on some models)

Water Filter Cartridge

The water filter cartridge is located in the back upper right

corner of the refrigerator compartment.

When to Replace the Filter on Models With a

Replacement Indicator Light

There is a replacement indicator light for the water filter

cartridge on the dispenser. This light will turn orange to tell

you that you need to replace the filter soon.

The filter cartridge should be replaced when the

replacement indicator light turns red or if the flow of water

to the dispenser or icemaker decreases.

When to Replace the Filter on Models Without a

Replacement Indicator Light

The filter cartridge should be replaced every six months

or earlier if the flow of water to the water dispenser or

icemaker decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one

by slowly turning it to the left. Do not pull down on the

cartridge. A small amount of water may drip down.

Installing the Filter Cartridge

If you are replacing a SmartWater cartridge with

an adapter, it must be removed before installing the

cartridge. To remove the adapter, turn it to the left

about 1/4 turn.

If you are replacing a Water by Culligan cartridge,

leave the adapter in place. This adapter will stay in the

refrigerator when you replace future cartridges.

On models without a replacement indicator light,

apply the month and year sticker to the new cartridge

to remind you to replace the filter in six months.

Fill the replacement cartridge with water from the tap

to allow for better flow from the dispenser immediately

after installation.

Line up the arrow on the cartridge and the cartridge

holder. Place the top of the new cartridge up inside the

holder. Do not push it up into the holder.

Slowly turn it to the right until the filter cartridge stops.

DO NOT OVERTIGHTEN. As you turn the cartridge, it will

automatically raise itself into position. The cartridge will

move about 1/2 turn.

Run water from the dispenser for 3 minutes (about 1-1/2

gallons) to clear the system and prevent sputtering.

Press and hold the WATER FILTER pad (on some models)

on the dispenser for 3 seconds.

NOTE: A newly-installed water filter cartridge may cause

water to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug when a replacement

filter cartridge is not available. The dispenser and the

icemaker will not operate without the filter or filter

bypass plug.

To use the filter bypass plug on Water by Culligan models,

you must first remove the filter adapter from the cartridge

holder by turning it to the left.

If you have questions—visit our Website

at ge.com,

or call 1.800.GE.CARES (1.800.432.2737).

Replacement filters:

To order additional filter cartridges in the United States,

visit our Website at ge.com, or call GE Parts and Accessories,

800.626.2002.

MSWF

Suggested Retail $36.95–41.95

Customers in Canada should consult the yellow pages for

the nearest Mabe Service Center.

Cartridge

Holder

Filter

Bypass

Plug

Filter

Bypass

Plug

SmartWater

Water by Culligan

(appearance may vary)

With adapter

Without adapter

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

About the shelves and bins.

ge.com

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins

The larger refrigerator door bins and

freezer tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight

up, then lift up and out.

To replace or relocate: Engage the back side

of the bin in the molded supports of the

door. Then push down on the front of the

bin. Bin will lock in place.

Small Bins

To remove: Lift the front of the bin straight

up then out.

To replace: Position the bin above the

rectangular molded supports on the door.

Then slide the bin down onto the support

to lock it in place.

The snugger helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Place a finger on either side of the

snugger near the rear and move it back

and forth to fit your needs.

CAUTION: On

models with an ice

chute inside the top

freezer door bin, be

careful when placing

items in the bin.

Make sure that

items do not block

or fall into the ice

chute.

Not all features are on all models.

Refrigerator bin

Freezer tilt-out bin

Snugger

Freezer bin

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

To remove:

Slide the shelf out until it reaches the stop,

then press down on the tab and slide the

shelf straight out.

Press tab and pull shelf

forward to remove

To replace or relocate:

Line the shelf up with the supports and

slide it into place. The shelf can be

repositioned when the door is at 90° or

more. To reposition the shelf, slide the shelf

past the stops and angle downward. Slide

shelf down to the desired position, line up

with the supports and slide into place.

Make sure you push the shelves all the way back

in before you close the door.

Do not block

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

About the shelves and bins.

Not all features are on all models.

QuickSpace

™

Shelf (on some models)

This shelf splits in half and slides under itself

for storage of tall items on the shelf below.

This shelf can be removed and replaced

or relocated just like Slide-Out Spillproof

Shelves.

On some models, this shelf can not be used

in the lowest position.

Slide-Out Freezer Shelves

To remove, slide out to the stop position,

lift the front past the stop position, and

slide out from rib.

Make sure you push the shelves all the way back

in before you close the door.

Freezer Baskets (on some models)

To remove, slide out to the stop position,

lift the front past the stop position, and

slide out.

Make sure you push the baskets all the way back

in before you close the door.

Fixed Freezer Shelves

To remove, lift the shelf up at the left side

and then bring the shelf out.

NOTE FOR DISPENSER MODELS: In order

to take full advantage of the tilt-out ice bin

(on some models), only store items on the

shelf below the ice bin that are no taller

than the lowest point on the bin.

Freezer Baskets (on some models)

To remove, push the basket all the way to the

back of the freezer. Lift up until the back

pins are disengaged. Lift the entire basket

up and pull out.

Make sure you push the baskets all the way back

in before you close the door.

Door Wine/Beverage Rack (on some models)

This rack holds up to 5 cans, one bottle of

wine or one 2-liter bottle of soda.

The rack hangs from the sides of the

dairy bin.

To remove:

Empty the wine/beverage rack.

Holding the bottom of the dairy bin,

lift the front straight up, then lift up

and out.

To detach the rack from the dairy bin,

pull the rack’s side wires out of the

holes on each side of the dairy bin.

To replace:

Reattach the rack to the sides

of the bin.

Engage the back side of the bin in

the molded supports on the door.

Then push down on the front of the

bin. The bin will lock into place.

Consumer Support

Troubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

About the refrigerator doors. ge.com

Refrigerator Doors

The refrigerator doors may feel different

than the ones you are used to. The

special door opening/closing feature

makes sure the doors close all the way

and are securely sealed.

When opening and closing the door you

will notice a stop position. If the door is

opened past this stop point, the door will

remain open to allow you to load and

unload food more easily. When the door

is only partially open, it will automatically

close.

The resistance you feel at the stop

position will be reduced as the door

is loaded with food.

When the door is only partially open,

it will automatically close.

Beyond this stop the door will

stay open.

Door Alignment

If doors are uneven, adjust the

refrigerator door.

Using a 7/16″ socket wrench, turn

the door adjusting screw to the right

to raise the door; to the left, to lower

it. (A nylon plug, imbedded in the

threads of the pin, prevents the pin

from turning unless a wrench is

used.)

After one or two turns of the

wrench, open and close the

refrigerator door and check the

alignment at the top of the doors.

To remove the base

grille, open the doors,

remove the screw at

each end of the base

grille and then pull

the grille straight out.

7/16″ Socket Wrench

Raise

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling

the drawer straight out and lifting the

drawer up and over the stop location.

If the door prevents you from taking out

the drawers, first try to remove the door

bins. If this does not offer enough

clearance, the refrigerator will need to

be rolled forward until the door opens

enough to slide the drawers out. In some

cases, when you roll the refrigerator out,

you will need to move the refrigerator

to the left or right as you roll it out.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

About the crispers and pans.

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the

bottom of the drawers should be wiped dry.

On some models, the bottom drawer has

full extension slides that allow full access

to the drawer.

Adjustable Humidity Crispers

Slide the control all the way to the HI setting

to provide high humidity recommended for

most vegetables.

Slide the control all the way to the LO

setting to provide lower humidity levels

recommended for most fruits.

HI LO

Convertible Deli Pan (on some models)

The convertible deli pan has its own cold

air duct to allow a stream of cold air from

the freezer compartment or refrigerator

compartment to flow to the pan.

The variable temperature control regulates

the air flow from the Climate Keeper.

Set the control to the coldest setting to

store fresh meats.

Set the control to cold to convert the pan

to normal refrigerator temperature and

provide extra vegetable storage space. The

cold air duct is turned off. Variable settings

between these extremes can be selected.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

About the automatic icemaker. ge.com

Automatic Icemaker

The icemaker will produce seven cubes

per cycle—approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.

See below for how to access ice and reach

the power switch on dispenser models.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch in the O (off) position.

When the refrigerator has been connected

to the water supply, set the power switch to

the l (on) position.

The icemaker will fill with water when it

cools to 15°F (–10°C). A newly installed

refrigerator may take 12 to 24 hours to begin

making ice cubes.

You will hear a buzzing sound each time

the icemaker fills with water.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing

ice. It is normal for several cubes to be

joined together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Lift the bin, then pull it

forward until the bin stops.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Lower the bin to access ice

or reach the power switch.

NOTE: In order to take full advantage

of the tilt-out ice bin, only store items

on the shelf below the ice bin that

are no taller than the lowest point

on the bin.

Models without a shelf

above the ice bin

To access ice and reach the

icemaker power switch:

Accessing Ice and Reaching the

Power Switch on Dispenser Models

There are two types of ice storage bins on

dispenser models. One has a shelf above

the bin, the other does not.

Special note about dispenser models

without a shelf above the ice bin:

■ These models have a tilt-out ice bin.

The bin can be tilted out as shown in

the illustrations, and it will hold itself

up while you take ice out or turn the

icemaker power switch on and off.

Be sure to put the bin back in place

before closing the door.

■ To restore your ice level from an empty

bucket stage, the following steps are

recommended:

12 hours after the first batch of ice

has fallen into the bin, dispense

3 to 4 cubes.

After an additional 6 hours, dispense

3 to 4 cubes again.

These steps will restore your ice level

in the shortest amount of time.

To access ice, pull the bin forward.

To reach the power switch, pull the

shelf straight out. Always be sure to

replace the shelf.

Models with a shelf

above the ice bin

Shelf

Ice Bin

Shelf

Ice Bin

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

About the ice and water dispenser. (on some models)

To Use the Dispenser

Select CUBED ICE , CRUSHED ICE

or WATER .

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To

reduce water spotting, the shelf and its

grille should be cleaned regularly.

If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system. Press the dispenser arm for at least two

minutes to remove trapped air from the water

line and to fill the water system. To flush out

impurities in the water line, throw away the first

six glassfuls of water.

CAUTION: Never put fingers or any other

objects into the ice crusher discharge opening.

Locking the Dispenser

Press the LOCK pad for

3 seconds to lock the

dispenser and control

panel. To unlock, press

and hold the pad again

for 3 seconds.

Dispenser Light

This pad turns the night

light in the dispenser on

and off. The light also

comes on when the

dispenser cradle is

pressed. If this light

burns out, it should be

replaced with a 6 watt

12V maximum bulb.

Quick Ice (on some models)

When you need ice

in a hurry, press this

pad to speed up ice

production. This will

increase ice production

for the following

48 hours or until you

press the pad again.

Door Alarm (on some models)

To set the alarm,

press this pad until the

indicator light comes

on. This alarm will

sound if either door

is open for more than

3 minutes. The light

goes out and the

beeping stops when

you close the door.

Spill Shelf

Important Facts About Your Dispenser

■ Do not add ice from trays or bags to

the storage drawer. It may not crush or

dispense well.

■ Avoid overfilling glass with ice and use of

narrow glasses. Backed-up ice can jam the

chute or cause the door in the chute to

freeze shut. If ice is blocking the chute,

poke it through with a wooden spoon.

■ Beverages and foods should not be

quick-chilled in the ice storage drawer.

Cans, bottles or food packages in the

storage drawer may cause the icemaker

or auger to jam.

■ To keep dispensed ice from missing

the glass, put the glass close to, but not

touching, the dispenser opening.

■ Some crushed ice may be dispensed even

though you selected CUBED ICE. This

happens occasionally when a few cubes

accidentally get directed to the crusher.

■ After crushed ice is dispensed, some

water may drip from the chute.

■ Sometimes a small mound of snow will

form on the door in the ice chute. This

condition is normal and usually occurs

when you have dispensed crushed ice

repeatedly. The snow will eventually

evaporate.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Care and cleaning of the refrigerator.

Cleaning the Outside

The dispenser drip area (on some models),

beneath the grille, should be wiped dry. Water

left in this area may leave deposits. Remove

the deposits by adding undiluted vinegar to

the well. Soak until the deposits disappear

or become loose enough to rinse away.

The dispenser cradle (on some models).

Before cleaning, lock the dispenser by

pressing and holding the LOCK pad for

3 seconds. Clean with warm water and

baking soda solution – about a tablespoon

(15 ml) of baking soda to a quart (1 liter)

of water. Rinse thoroughly and wipe dry.

The door handles and trim. Clean with

a cloth dampened with soapy water.

Dry with a soft cloth.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning. If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution –

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both

cleans and neutralizes odors. Rinse and

wipe dry.

Use of any cleaning solution other than that

which is recommended, especially those that

contain petroleum distillates, can crack or

damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot water

because the extreme temperature difference

may cause them to break. Handle glass shelves

carefully. Bumping tempered glass can cause

it to shatter.

Do not wash any plastic refrigerator parts in the

dishwasher.

Dispenser drip area.

ge.com

Lift the bin, then pull it

forward until the bin stops.

Lift and pull forward again

to remove the bin.

Models without a shelf

above the ice bin

To remove:

Models with a shelf

above the ice bin

To remove:

Removing and Replacing the Ice

Storage Bin on Dispenser Models

There are two types of ice storage bins on

dispenser models. One has a shelf above

the bin, the other does not.

Always set the icemaker power switch to the

O (off) position before removing the ice bin.

When replacing either type of ice bin:

Always be sure to press it firmly into place.

If it does not go all the way back, remove it

and rotate the drive mechanism 1/4 turn.

Then push the bin back again.

Pull the bin straight out, then lift past

the stop position.

Rotate

Drive

Mechanism

For long vacations or absences, remove

food and unplug the refrigerator. Clean

the interior with a baking soda solution

of one tablespoon (15 ml) of baking soda

to one quart (1 liter) of water. Leave the

doors open.

Set the icemaker power switch to the

O (off) position and shut off the water

supply to the refrigerator.

If the temperature can drop below

freezing, have a qualified servicer drain

the water supply system (on some models)

to prevent serious property damage due

to flooding.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Care and cleaning of the refrigerator.

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure

you don’t roll over the power cord or icemaker

supply line (on some models).

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and

drawers by taping them securely in place

to prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back

of the refrigerator against the hand truck.

This could damage the refrigerator. Handle

only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

Consumer Support

Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Replacing the light bulbs. ge.com

NOTE: Turning the refrigerator off via the controls on the touch panel does not shut off electrical power to the

refrigerator.

Refrigerator Compartment—Upper Light

Unplug the refrigerator.

The bulbs are located at the top of the

compartment, inside the light shield.

On some models, a screw at the front of

the light shield will have to be removed.

On other models, the screw is located

in the pocket located at the back of

the shield.

To remove the light shield, on some

models, press in on the tabs on the sides

of the shield and slide forward and out.

On other models, just slide the shield

forward and out.

After replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the light shield and

screw. When replacing the light shield,

make sure that the tabs at the back of

the shield fit into the slots at the back

of the light shield housing.

Plug the refrigerator back in.

Refrigerator Compartment—Lower Light

This light is located above the top drawer.

Unplug the refrigerator.

Lift the light shield up and pull it out.

After replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the shield.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light

shield. (The shelf will be easier to

remove if it is emptied first.) Remove

the screw at the top of the light shield.

To remove the light shield, press in on

the sides, and lift up and out.

Replace the bulb with an appliance

bulb of the same or lower wattage,

and reinstall the light shield. When

reinstalling the light shield, make

sure the top tabs snap securely

into place. Replace the screw.

Reinstall the shelf and plug the

refrigerator back in.

Dispenser

Unplug the refrigerator.

The bulb is located on the dispenser

under the control panel.

Remove the light bulb by turning

it counterclockwise.

Replace the bulb with a bulb of the

same size and wattage.

Plug the refrigerator back in.

Tabs

Your light shield will look like

one of the following:

Pocket

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

•

IMPORTANT — Save these

instructions for local inspector’s use.

•

IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Skill level – Installation of this appliance

requires basic mechanical skills.

• Completion time – Refrigerator Installation

30 minutes

Water Line Installation

30 minutes

• Proper installation is the responsibility of

the installer.

• Product failure due to improper installation

is not covered under the Warranty.

If the refrigerator has already been installed,

remove the base grille (see Step 2 in Moving

the Refrigerator), then skip to Step 5 in

Installing the Refrigerator.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.361.3400 or Visit our Website at: www.geappliances.ca

Installation

Refrigerator

Instructions

Models 22, 23, 25 & 27

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. A GE

water supply kit (containing tubing, shutoff

valve, fittings and instructions) is available

at extra cost from your dealer, by visiting

our Website at ge.com (in Canada at

www.geappliances.ca) or from Parts and

Accessories, 800.626.2002 (in Canada

1.888.261.3055).

PREPARATION

WATER SUPPLY TO THE ICEMAKER

TOOLS YOU WILL NEED

Phillips Head Screwdriver

3/8″ and 5/16″ Socket 1/2″ and 7/16″ Wrench

Plastic Putty Knife

Installation Instructions

LOADING THE RERIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors

until the refrigerator is in its final location.

To move the refrigerator, use a padded

hand truck. Center the refrigerator on the

hand truck and secure the strap around

the refrigerator. DO NOT OVERTIGHTEN

THE STRAP.

REMOVE THE BASE GRILLE

Remove the grille by removing the two

Phillips head screws.

If the refrigerator must go through

any entrance that is less than 38″

wide, the doors must be removed.

Proceed to Step 3.

DO NOT remove the handles.

If all entrances are more than

38″ wide, skip to Installing

the Refrigerator.

DISCONNECT THE WATER

COUPLING (on some models)

If the refrigerator has a water dispenser,

there is a water line from the cabinet into

the bottom hinge on the freezer door that

must be disconnected.

To disconnect, push in on the white collar

of the coupling and pull out the tubing.

White collar

Bottom

freezer

hinge

MOVING THE REFRIGERATOR

Installation Instructions

DISCONNECT THE POWER

COUPLING (on some models)

If the refrigerator has a water dispenser,

there is a power line (harness) from the

cabinet into the bottom hinge on the

freezer door that must be disconnected.

To disconnect, pull apart at the coupling.

Bottom

freezer

hinge

DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

If the refrigerator has a refreshment

center, there are electrical connectors

(harnesses) from the cabinet into the

bottom hinge on the refrigerator door

that must be disconnected.

To disconnect, pull apart each connector.

Bottom

refrigerator

hinge

CLOSE THE FREEZER AND

REFRIGERATOR DOORS

REMOVE THE FREEZER DOOR

Remove the freezer door top hinge cover

by either squeezing it and pulling it up or

by prying it off with a plastic putty knife.

Remove the two 5/16” hex head screws,

then lift the hinge straight up to free the

hinge pin.

Open the freezer door to 90.°

5/16” Hex Head

90°

MOVING THE REFRIGERATOR (CONT.)

Installation Instructions

REMOVE THE

FREEZER DOOR (cont.)

As one person slowly lifts the freezer door

up and off the bottom hinge, the second

person should carefully guide the water

line and power line (harness) through the

bottom hinge.

Set the door on a non-scratching surface

with the inside up.

90°

REMOVE THE

REFRIGERATOR DOOR

Remove the refrigerator door top hinge

cover by either squeezing it and pulling

it up or by prying it off with a plastic

putty knife.

REMOVE THE

REFRIGERATOR DOOR (cont.)

Remove the two 5/16” hex head screws,

then lift the hinge straight up to free the

hinge pin.

Open the refrigerator door to 90.°

5/16” Hex Head

90°

Installation Instructions

REMOVE THE

REFRIGERATOR DOOR (cont.)

Lift the refrigerator door up and off the

bottom hinge.

If the refrigerator has a refreshment

center, one person should slowly lift the

door up and off the bottom hinge and the

second person should carefully guide the

electrical lines (harnesses) through the

bottom hinge.

Set the door on a non-scratching surface

with the inside up.

90°

REPLACING THE DOORS

To replace the doors, simply reverse

steps 3 through 8.

However, please note the following:

• When lowering the doors onto the

bottom hinges, make sure the second

person carefully guides the tube and

harnesses through the holes in the

hinges.

• When connecting the water line, make

sure you insert the tubing all the way

to the mark.

• Do not pinch the tubing and harnesses

when placing the doors on the bottom

hinges.

• When connecting the power line and

the electrical lines (refreshment center

models only), be sure that the

connectors are seated together fully.

Mark

MOVING THE REFRIGERATOR (CONT.)

Refreshment Center Models only

La page charge ...

GE 22, 23, 25, 27 Manuel utilisateur

Marque: GE

Modèle: 22, 23, 25, 27

Catégorie: Frigos

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: GE 22, 23, 25, 27 User manual
español: GE 22, 23, 25, 27 Manual de usuario

Documents connexes

Autres documents

Mabe Canada 25 Manuel utilisateur