Novamatic WA914E Manuel utilisateur

Marque: Novamatic

Modèle: WA914E

Catégorie: Machines à laver

Taper: Manuel utilisateur

WA914.1 E

User Manual

Washing Machine

CONTENTS

Safety information 2

Safety instructions 3

Product description 5

Control panel 5

Programme Chart 6

Consumption values 8

Options 9

Settings 11

Before first use 11

Daily use 11

Hints and tips 15

Care and cleaning 16

Troubleshooting 19

Technical Data 21

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damages that are the result of

incorrect installation or usage. Always keep the instructions

in a safe and accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Do not let children play with the appliance.

• Children aged 3 years and under must be kept away from

this appliance when it is in operation at all times.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the

door is open.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

General Safety

• Do not change the specification of this appliance.

• Do not exceed the maximum load of 9 kg (refer to the

"Programme chart" chapter).

• The operating water pressure at the water entry point from

the outlet connection must be between 0.5 bar (0.05 MPa)

and 8 bar (0.8 MPa).

• The ventilation opening in the base must not be covered

by a carpet, mat, or any floor covering.

• The appliance must be connected to the water mains using

the new supplied hose sets, or other new hose sets

supplied by the Authorised Service Centre.

• Old hose sets must not be reused.

• If the mains power supply cable is damaged, it must be

replaced by the manufacturer, its Authorised Service

Centre or similarly qualified persons to avoid an electrical

hazard.

• Before any maintenance operation, deactivate the

appliance and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to

clean the appliance.

• Clean the appliance with a moist cloth. Use only neutral

detergents. Do not use abrasive products, abrasive

cleaning pads, solvents or metal objects.

SAFETY INSTRUCTIONS

Installation

• Remove all the packaging and the

transit bolts.

• Keep the transit bolts in a safe place. If

the appliance is to be moved in future

they must be reattached to lock the

drum to prevent internal damage.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Do not install or use a damaged

appliance.

• Follow the installation instruction

supplied with the appliance.

• Do not install or use the appliance

where the temperature can be less

than 0°C or where it is exposed to the

weather.

• The floor area where the appliance is to

be installed must be flat, stable, heat

resistant and clean.

• Make sure that there is air circulation

between the appliance and the floor.

• Do not install the appliance directly

over the floor drain.

• Adjust the feet to have the necessary

space between the appliance and the

flooring.

• Do not install the appliance where the

appliance door cannot be fully opened.

• Do not put a container to collect

possible water leakage under the

appliance. Contact the Authorised

Service Centre to ensure which

accessories can be used.

Electrical connection

• The appliance must be earthed.

• Always use a correctly installed

shockproof socket.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the mains cable need to be

replaced, this must be carried out by

our Authorised Service Centre.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• Do not touch the mains cable or the

mains plug with wet hands.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• This appliance complies with the E.E.C.

Directives.

Water connection

• Do not cause damage to the water

hoses.

• Before connection to new pipes, pipes

not used for a long time, where repair

work has been carried out or new

devices fitted (water meters, etc.), let

the water flow until it is clean and clear.

• Ensure that there are no visible water

leaks during and after the first use of

the appliance.

• Do not use an extension hose if the

inlet hose is too short. Contact the

service centre for the replacement of

the inlet hose.

• You can extend the drain hose to

maximum 400 cm. Contact the service

centre for the other drain hose and the

extension.

Use

WARNING! Risk of injury,

electrical shock, fire, burns or

damage to the appliance.

• This appliance is for household use

only.

• Follow the safety instructions on the

detergent packaging.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

• Make sure that all metal objects are

removed from the laundry.

• Do not wash fabrics which are heavily

soiled with oil, grease or other greasy

substances. It can damage rubber

parts of the washing machine. Prewash

such fabrics by hand before loading

them into the washing machine.

• Do not touch the glass door while a

programme is in operation. The glass

can get hot.

Service

• To repair the appliance contact an

Authorised Service Centre.

• Use original spare parts only.

Disposal

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the

mains electrical and water supplies.

• Cut off the mains electrical cable close

to the appliance and dispose of it.

• Remove the door catch to prevent

children or pets from becoming trapped

in the drum.

• Dispose of the appliance in accordance

with local requirements for the disposal

of Waste Electrical and Electronic

Equipment (WEEE).

PRODUCT DESCRIPTION

Appliance overview

1 2 3

Worktop

Detergent dispenser

Control panel

Door handle

Rating plate

Feet for levelling the appliance

CONTROL PANEL

Control panel description

90°

60°

40°

30°

1400

1200

800

97621 3 4 5 8

Kurz /

Rapide

Buntwäsche / Coton

Pflegeleicht / Synthétiques

Feinwäsche / Délicats

Wolle / Laine

Auffrischen 20 min / Rafraîchir 20'

Mix 20° / Programme Mix 20°

Intensiv /

Intensif

Bügelquick /

Repassage Facile

Spülen /

Rinçage seul

Pumpen /

Essorage

On/Off

ECO

Ende in / Fini dans

On/Off button

Programme selection touchpad

Temperature selection touchpad

Spin selection touchpad

Options selection touchpad

Start/Pause touchpad

Ende in/Fini dans touchpad

Display

Door locked indicator

Display

Ende in / Fini dans

B C

A. The time area:

• : the programme duration

• : the "finish in" time

• : the alarm codes

• : the message of error

• : the programme is completed.

B. The child lock indicator:

• The indicator comes on when you

activate this device.

C. The extra rinse indicator:

• The indicator comes on when you

activate this option.

D. The Ende in/Fini dans touchpad.

PROGRAMME CHART

Programme

Temperature

range

Maximum

load

Maximum

spin speed

Programme description

(Type of load and soil level)

30' @ 30°

30 °C

3 kg

800 rpm

A short cycle for synthetic and delicate items with

light soil level or for items to freshen up.

Buntwäsche/

Coton

90 °C - Cold

9 kg

1400 rpm

White cotton and coloured cotton. Normal soil and

light soil.

Buntwä‐

sche/Coton

ECO

60 °C - 40 °C

9 kg

1400 rpm

White cotton and fast-coloured cotton. Normal soil.

The energy consumption decreases and the time of

the washing programme is extended.

Pflegeleicht/

Synthétiques

60 °C - Cold

3,5 kg

1200 rpm

Synthetic items or mixed fabric items. Normal soil.

Feinwäsche/

Délicats

40 °C - Cold

3,5 kg

1200 rpm

Delicate fabrics such as acrylics, viscose and

mixed fabrics requiring a mild washing. Normal

soil.

Wolle/Laine

40 °C - Cold

2 kg

1200 rpm

Machine washable wool, hand washable wool and

other fabrics with «hand washing» care symbol

Programme

Temperature

range

Maximum

load

Maximum

spin speed

Programme description

(Type of load and soil level)

Daunen/Couette

60 °C - Cold

3 kg

800 rpm

Special programme for one synthetic blanket, du‐

vet, bedspread and so on.

Mix 20°/

Programme Mix

20°

20 °C

2 kg

1200 rpm

Special programme for cotton, synthetic and mixed

fabrics with light soil. Set this programme to decrease

the energy consumption. Make sure that the deter‐

gent is for low temperature in order to have good

washing results

Standard programmes for the Energy Label consumption values. According to regulation 1061/2010,

these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton pro‐

gramme». They are the most efficient programmes in terms of combined energy and water consumption for

washing normally soiled cotton laundry.

The water temperature of the washing phase may differ from the temperature declared for the se‐

lected programme.

During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or

doesn't rotate properly, but this is normal for this programme.

No temperature indicator is on .

Programme options compatibility

Pro‐

gramme

Kurz/

Rap‐

ide

In‐

ten‐

siv/

In‐

ten‐

sif

Bü‐

gel‐

quick/

Re‐

pas‐

sage

Facile

Spü‐

len/

Rin‐

çage

seul

Pump‐

en/

Essor‐

age

30' @ 30° ■ ■ ■ ■

Buntwä‐

sche/

Coton

■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Buntwä‐

sche/

Coton

ECO

■ ■ ■ ■ ■ ■ ■ ■

Pflege‐

leicht/

Synthé‐

tiques

■ ■ ■ ■ ■ ■ ■ ■ ■ ■

Pro‐

gramme

Kurz/

Rap‐

ide

In‐

ten‐

siv/

In‐

ten‐

sif

Bü‐

gel‐

quick/

Re‐

pas‐

sage

Facile

Spü‐

len/

Rin‐

çage

seul

Pump‐

en/

Essor‐

age

Feinwä‐

sche/Déli‐

cats

■ ■ ■ ■ ■ ■ ■ ■ ■

Wolle/

Laine

■ ■ ■ ■ ■ ■

Daunen/

Couette

■ ■ ■ ■ ■ ■

Mix 20°/

Pro‐

gramme

Mix 20°

■ ■ ■ ■ ■ ■ ■

When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to keep

the full load but the washing results can be unsatisfactory. Recommended load: cotton: 4,5 kg, synthetics and

delicates: 2,5 kg.

CONSUMPTION VALUES

Stated values are obtained in laboratory conditions with relevant stand‐

ards. Different causes can change the data: the quantity and type of laun‐

dry and ambient temperature. Water pressure, the supply voltage and the

temperature of inlet water may also affect the washing programme dura‐

tion.

Technical specifications may be changed without prior notice to improve

the quality of product.

At the start of the programme, the display shows the programme duration

for the maximum load capacity.

During the washing phase the programme duration is automatically cal‐

culated and can be greatly reduced if the laundry load is lower than the

maximum load capacity (e.g. Cotton 60°C, maximum load capacity 9 kg,

the programme duration exceeds 2 hours; actual load 1 kg, the pro‐

gramme duration will be less than 1 hour).

When the appliance is calculating the real programme duration a dot

flashes in the display.

Programmes Load

(kg)

Energy

consump‐

tion (kWh)

Water

consump‐

tion (litre)

Approxi‐

mate pro‐

gramme

duration

(minutes)

Remain‐

ing mois‐

ture (%)

Buntwäsche/Coton

60°C

9 1,58 84 175 53

Buntwäsche/Coton

40°C

9 1,01 82 174 53

Pflegeleicht/

Synthétiques 40°C

3,5 0,74 61 122 35

Feinwäsche/Déli‐

cats 40°C

3,5 0,54 62 74 35

Wolle/Laine

30°C

2 0,42 62 70 30

Standard cotton programmes

Standard 60°C cot‐

ton

9 1,03 49 220 53

Standard 60°C cot‐

ton

4,5 0,77 40 187 53

Standard 40°C cot‐

ton

4,5 0,62 40 181 53

At the end of spin phase.

Not available for some models.

Off Mode (W) Left On Mode (W)

0.48 0.48

The information given in the chart above is compliant with the EU Commission regulation

1015/2010 implementing directive 2009/125/EC .

OPTIONS

Temperature

With this option you can change the

default temperature.

Indicator = cold water.

The indicator of the set temperature

comes on.

Spin

With this option you can change the

default spin speed.

The indicator of the set speed comes on.

Additional spin options:

No Spin

• Set this option to deactivate all spin

phases. Only the drain phase is

available.

• The related indicator comes on.

• Set this option for very delicate fabrics.

• The rinses phase uses more water for

some washing programmes.

Rinse Hold

• Set this option to prevent the laundry

creases.

• The related indicator comes on.

• There is a water in the drum when the

programme is completed.

• The drum turns regularly to prevent the

laundry creases.

• The door stays locked. You must drain

the water to unlock the door.

To drain the water refer to ‘At

the end of the programme’.

Kurz/Rapide

With this option you can decrease the

programme duration.

Use this option for items with light soil or

items to refresh.

The related indicator comes on.

Intensiv/Intensif

With this option you can wash very soiled

laundry.

The washing cycle lasts longer with this

option.

The related indicator comes on.

Bügelquick/Repassage Facile

The appliance carefully washes and spins

the laundry to prevent the creases.

The appliance decreases the spin speed,

uses more water and adapts the

programme duration to the type of

laundry.

The related indicator comes on.

Spülen/Rinçage seul

With this option you can perform only a

last rinse of a selected washing

programme.

If you set also the Extra Rinse function

( ) the appliance adds two or more

rinses.

The related indicator comes on.

Pumpen/Essorage

With this option you can perform the spin

and drain cycle.

The spin phase is suitable to the washing

programme you set.

If you set also the No Spin ( )

option, the appliance only

drains.

Ende in/Fini dans

With this option you can set the number of

hours in which you would like your

washing programme to be completed.

You can set from minimum 3 hours to

maximum 20 hours.

The display shows the number of hours

and the indicator above the button is

on.

Extra Rinse

With this option you can add some rinses

to a washing programme.

Use this option for persons allergic to

detergents and in areas where the water

is soft.

The related indicator comes on.

See in "Settings" how to activate this option.

SETTINGS

Extra Rinse

With this option you can permanently have

an extra rinse when you set a new

programme.

• To activate/deactivate this option

touch the buttons and at the

same time until the indicator comes

on/goes off.

Child Lock

With this option you can prevent that the

children play with the control panel.

• To activate/deactivate this option,

touch the buttons and at the

same time until the indicator comes

on/goes off.

Activate this option after you touch the

button : the buttons are locked (except

for the button ) .

This option stays active even

when you switch off the

appliance.

Acoustic signals

The acoustic signals operate when:

• The programme is completed.

• The appliance has a malfunction.

To deactivate/activate the acoustic

signals, touch the buttons and at the

same time for 4 seconds.

If you deactivate the acoustic

signals, they continue operate

when the appliance has a

malfunction.

BEFORE FIRST USE

1. Put a small quantity of detergent in the

compartment for washing phase.

2. Set and start a programme for cotton

at the highest temperature without

laundry.

This removes all possible dirt from the

drum and the tub.

DAILY USE

WARNING! Refer to Safety

chapters.

Loading the laundry

1. Open the appliance door

2. Shake the items before you put them

in the appliance.

3. Put the laundry in the drum, one item

at a time.

Make sure not to put too much laundry in

the drum.

4. Close the door firmly.

CAUTION! Make sure that no

laundry stays between the seal

and the door. There is a risk of

water leakage or damage to

the laundry.

Washing heavily oiled, greasy

stains could cause damage

rubber parts of the washing

machine.

Using detergent and additives

1. Measure out the detergent and the

fabric conditioner.

2. Put the detergent and the fabric

conditioner into the compartments.

3. Carefully close the detergent drawer

Detergent compartments

Detergent compartment for

washing phase.

If you use liquid detergent, put

it immediately before you start

the programme.

Compartment for liquid addi‐

tives (fabric conditioner,

starch).

CAUTION! Do

not exceed the

MAX level.

Flap for powder or liquid de‐

tergent.

Liquid or powder detergent

• Position A for powder detergent (factory setting).

• Position B for liquid detergent.

When you use the liquid detergent:

• Do not use gelatinous or thick liquid detergents.

• Do not put more liquid then the maximum level.

• Do not set the delay start (or Finish in option).

Activating the appliance

Press and hold for a couple of seconds

the On/Off button to activate or deactivate

the appliance.

A tune sounds when the appliance is

activated.

The display shows the word On.

Setting a programme

1. Touch the programme button and

set the programme:

• The indicator of the button

flashes.

• The display shows the programme

duration.

2. If necessary, change the temperature

and the spin speed or add available

options. When you activate an option,

the indicator of the set option comes

on.

If you set something incorrect,

the display shows the message

Starting a programme without

the Ende in/Fini dans option

Touch the button .

• The indicator of the button

stops to flash and stays on.

• The programme starts, the door

locks, the indicator is on.

• The drain pump can operate for a

short time at the beginning of the

washing cycle.

After approximately 15 minutes

from the start of the

programme:

• The appliance adjusts

automatically the

programme duration agree

with the laundry load.

• The display shows the new

value.

Starting a programme with the

Ende in/Fini dans option

1. Touch the button again and again

to choose the number of hours in

which you want the washing cycle to

be finished.

The display shows the number of hours

you set (e.g. ) and the indicator above

the button is on to show that his option

is active.

2. Touch the button :

• The door is locked.

• The appliance starts the

countdown.

• When the countdown is completed,

the programme starts automatically.

You can cancel or change the

set of the Ende in/Fini dans

option before you touch the

button . After touching the

button you can only cancel

the Ende in/Fini dans option.

To cancel the the Ende in/Fini dans

option:

a. Touch the button to set the

appliance to pause. The indicator

of button flashes.

b. Touch the button until the

indicator above this button goes

off.

Touch the button

again to start

the programme immediately.

Interrupting a programme and

changing the options

You can change only some options before

they operate.

1. Touch

The indicator of this button flashes.

2. Change the options. If you change any

option the Ende in/Fini dans option (if

set) will be disabled.

3. Touch again.

The programme continues.

Cancelling a programme

1. Press the button for some seconds

to cancel the programme and to

deactivate the appliance.

2. Press the same button again to

activate the appliance. Now, you can

set a new washing programme.

Before starting the new

programme the appliance could

drain the water. In this case,

make sure that the detergent is

still in the detergent

compartment, if not fill the

detergent again.

Opening the door

While a programme (or the ) operates,

the appliance door is locked. The indicator

is on.

CAUTION! If the temperature

and level of the water in the

drum are too high, you cannot

open the door.

To open the door during the first

minutes of the cycle (or when the

operates) :

1. Touch the button to pause the

appliance.

2. Wait until the indicator goes off.

3. You can open the door.

4. Close the door and touch the button

again. The programme (or the )

continues.

At the end of the programme

• The appliance stops automatically.

• The acoustic signal operates (if it is

activated).

• In the display comes on.

• The indicator of the button goes off.

• You can open the door.

• Remove the laundry from the

appliance. Make sure that the drum is

empty.

• Press the button for some seconds

to deactivate the appliance.

• Close the water tap.

• Keep the door and the detergent

drawer ajar, to prevent the mildew and

odours.

The washing programme is completed,

but there is water in the drum:

• The drum turns regularly to prevent the

creases in the laundry.

• The indicator flashes to remind you

to drain the water.

• The door lock indicator is on. The

indicator of button flashes. The

door stays locked.

• You must drain the water to open the

door.

Draining the water:

1. To drain the water.

• Touch the button . The

appliance drains the water and

spins with the maximum spin speed

for selected washing programme.

• Alternatively, touch the button to

change the spin speed and then

touch the button . The appliance

drains the water and spins. If you

set , the appliance only drains.

2. Press the button for some seconds

to deactivate the appliance.

The appliance drains and spins

automatically after

approximately 18 hours (except

for Wool programme).

AUTO-OFF option

The AUTO-OFF stand-by option

automatically deactivates the appliance to

decrease the energy consumption. All the

indicators and the display go off when :

• You do not use the appliance for 5

minutes before you touch .

Press the button to activate the

appliance again.

• After 5 minutes from the end of the

washing programme.

Press the button to activate the

appliance again.

The display shows the end of the last

set programme.

Touch the button

if you want to set a

new cycle.

HINTS AND TIPS

The laundry load

• Divide the laundry in: white, coloured,

synthetics, delicates and wool.

• Obey the washing instructions that are

on the laundry care labels.

• Do not wash white and coloured items

together.

• Some coloured items can discolour

with the first wash. We recommend that

you wash them separately for the first

times.

• Button up pillowcases, close zippers,

hooks and poppers. Tie up belts.

• Empty the pockets and unfold the

items.

• Turn multilayered fabrics, wool and

items with painted illustrations inside

out.

• Remove hard stains with a special

detergent.

• Wash and pre-treat heavy soil stains

before putting items in drum

• Be careful with the curtains. Remove

the hooks and put the curtains in a

washing bag or pillowcase.

• Do not wash laundry without hems or

with cuts. Use a washing bag to wash

small and/or delicate items (e.g.

underwired bras, belts, tights, etc. ).

• A very small load can cause balance

problems with the spin phase. If this

occurs, adjust manually the items in the

tub and start the spin phase again.

Stubborn stains

For some stains, water and detergent is

not sufficient.

We recommend that you pre-treat these

stains before you put the items in the

appliance.

Special stain removers are available. Use

the special stain remover that is applicable

to the type of stain and fabric.

Detergents and additives

• Only use detergents and additives

specially made for washing machines:

– powder detergents for all types of

fabric,

– powder detergents for delicate

fabrics (40 °C max) and woollens,

– liquid detergents, preferably for low

temperature wash programmes (60

°C max) for all types of fabric, or

special for woollens only.

• Do not mix different types of

detergents.

• To help the environment, do not use

more than the correct quantity of

detergent.

• Obey the instructions that you find on

the on packaging of these products.

• Use the correct products for the type

and colour of the fabric, the programme

temperature and the level of soil.

• If your appliance does not have the

detergent dispenser with the flap

device, add the liquid detergents with a

dosing ball (supplied by the detergent's

manufacturer).

Ecological hints

• Always start a washing programme

with the maximum load of laundry

allowed.

• If necessary, use a stain remover when

you set a programme with a low

temperature.

• To use the correct quantity of

detergent, check the water hardness of

your domestic system. Refer to "Water

hardness".

Water hardness

If the water hardness in your area is high

or moderate, we recommend that you use

a water softener for washing machines. In

areas where the water hardness is soft it

is not necessary to use a water softener.

To know the water hardness in your area,

contact your local water authority.

Use the correct quantity of the water

softener. Obey the instructions that you

find on the packaging of the product.

CARE AND CLEANING

WARNING! Refer to Safety

chapters.

External cleaning

Clean the appliance with soap and warm

water only. Fully dry all the surfaces.

CAUTION! Do not use alcohol,

solvents or chemical products.

Descaling

If the water hardness in your area is high

or moderate, we recommend that you use

a water descaling product for washing

machines.

Regularly examine the drum to prevent

limescale and rust particles.

To remove rust particles use only special

products for washing machines. Do this

separately from the laundry wash.

Always obey the instructions

that you find on the packaging

of the product.

Maintenance wash

With the low temperature programmes it is

possible that some detergent stays in the

drum. Perform a maintenance wash

regularly. To do this:

• Remove all laundry from the drum.

Door seal

Regularly examine the seal and remove

all objects from the inner part.

Cleaning the detergent dispenser

1. 2.

3. 4.

Cleaning the inlet hose and the valve filter

3. 4.

45°

20°

Frost precautions

If the appliance is installed in an area

where the temperature can be less than 0

°C, remove the remaining water from the

inlet hose and the drain pump.

Do this procedure also when

you want to do the emergency

drain.

1. Disconnect the mains plug from the

mains socket.

2. Close the water tap.

3. Remove the water inlet hose.

4. Remove the drain hose from the rear

support and unhook it from sink or

spigot.

5. Put the ends of the drain and inlet

hose in a container. Let the water flow

out of the hoses.

6. When no more water flows, install the

inlet hose and the drain hose again.

WARNING! Make sure that the

temperature is more than 0 °C

before you use the appliance

again. The manufacturer is not

responsible for damages

caused by low temperatures.

TROUBLESHOOTING

WARNING! Refer to Safety

chapters.

Introduction

The appliance does not start or it stops

during operation.

First try to find a solution to the problem

(refer to the table). If the problem persists,

contact the Authorised Service Centre.

With some problems, the acoustic

signals operate and the display shows

an alarm code:

• - The appliance does not fill with

water properly.

• - The appliance does not drain

the water.

• - The appliance door is open or

not closed correctly. Please check the

door!

If the appliance is

overloaded, remove some

items from the drum and/or

keep pressed the door and

push the button at the

same time until the indicator

stops flashing (see the

picture below).

• - The mains supply is unstable.

Wait until the mains supply is stable.

• - No communication between

electronic elements of the appliance.

Switch off and switch on again.

WARNING! Deactivate the

appliance before you do the

checks.

Possible failures

Problem Possible solution

The programme does

not start.

• Make sure that the mains plug is connected to the mains

socket.

• Make sure that the appliance door is closed.

• Make sure that there is not a damaged fuse in the fuse box.

• Make sure that the Start/Pause has been pressed.

• If the delay start is set, cancel the setting or wait for the end of

countdown.

• Deactivate the Child Lock function if it is on.

Problem Possible solution

The appliance does not

fill with water properly.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too low.

For this information, contact your local water authority.

• Make sure that the water tap is not clogged.

• This problem may be caused by the filter of the inlet hose or

the valve drain filter which may be clogged. Refer to “Care

and cleaning”. If problem remains please contact the Author‐

ised Service Centre.

• Make sure that the inlet hose has no kinks or bends.

• Make sure that the connection of the water inlet hose is cor‐

rect.

The appliance does not

drain the water.

• Make sure that the sink spigot is not clogged.

• Make sure that the drain hose has no kinks or bends.

• Make sure that the connection of the drain hose is correct.

• Set the drain option if you set a programme without drain

phase.

• Set the drain option if you set an option which ends with water

in the drum.

• This problem may be caused by the clogged drain filter.

Please contact the Authorised Service Centre.

The spin phase does not

operate or the washing

cycle lasts longer than

usually.

• Adjust manually the items in the tub and start the spin phase

again. This problem may be caused by balance problems.

• Set the spin option.

• Set the drain option if you set an option which ends with water

in the drum.

• This problem may be caused by the clogged drain filter.

Please contact the Authorised Service Centre.

There is water on the

floor.

• Make sure that the couplings of the water hoses are tight and

there is not water leakages.

• Make sure that the water inlet hose and the drain hose have

no damages.

• Make sure you use the correct detergent and the correct

quantity of it.

You cannot open the ap‐

pliance door.

• Make sure that the washing programme is finished.

• Set the drain or the spin option if there is water in the drum.

• Do the emergency drain procedure. See "Frost precautions"

(in "Care and Cleaning" chapter).

The appliance makes an

unusual noise.

• Make sure the levelling of the appliance is correct. Refer to

'Installation instruction'.

• Make sure that the packaging and/or the transit bolts are re‐

moved. Refer to 'Installation instruction'.

• Add more laundry in the drum. The load may be too small.

La page charge ...

Novamatic WA914E Manuel utilisateur

Marque: Novamatic

Modèle: WA914E

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Novamatic WA914E User manual

Novamatic WA914E Manuel utilisateur

Novamatic WA914E Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents