Novamatic WA914E Manuel utilisateur

Novamatic
Marque
Novamatic
Modèle
WA914E
Catégorie
Machines à laver
Taper
Manuel utilisateur
WA914.1 E
User Manual
Washing Machine
CONTENTS
Safety information 2
Safety instructions 3
Product description 5
Control panel 5
Programme Chart 6
Consumption values 8
Options 9
Settings 11
Before first use 11
Daily use 11
Hints and tips 15
Care and cleaning 16
Troubleshooting 19
Technical Data 21
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damages that are the result of
incorrect installation or usage. Always keep the instructions
in a safe and accessible location for future reference.
Children and vulnerable people safety
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
• Do not let children play with the appliance.
• Children aged 3 years and under must be kept away from
this appliance when it is in operation at all times.
• Keep all packaging away from children and dispose of it
appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance when the
door is open.
• Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
• Do not change the specification of this appliance.
2
• Do not exceed the maximum load of 9 kg (refer to the
"Programme chart" chapter).
• The operating water pressure at the water entry point from
the outlet connection must be between 0.5 bar (0.05 MPa)
and 8 bar (0.8 MPa).
• The ventilation opening in the base must not be covered
by a carpet, mat, or any floor covering.
• The appliance must be connected to the water mains using
the new supplied hose sets, or other new hose sets
supplied by the Authorised Service Centre.
• Old hose sets must not be reused.
• If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service
Centre or similarly qualified persons to avoid an electrical
hazard.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to
clean the appliance.
• Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
SAFETY INSTRUCTIONS
Installation
• Remove all the packaging and the
transit bolts.
• Keep the transit bolts in a safe place. If
the appliance is to be moved in future
they must be reattached to lock the
drum to prevent internal damage.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use a damaged
appliance.
• Follow the installation instruction
supplied with the appliance.
• Do not install or use the appliance
where the temperature can be less
than 0°C or where it is exposed to the
weather.
• The floor area where the appliance is to
be installed must be flat, stable, heat
resistant and clean.
• Make sure that there is air circulation
between the appliance and the floor.
• Do not install the appliance directly
over the floor drain.
• Adjust the feet to have the necessary
space between the appliance and the
flooring.
• Do not install the appliance where the
appliance door cannot be fully opened.
• Do not put a container to collect
possible water leakage under the
appliance. Contact the Authorised
3
Service Centre to ensure which
accessories can be used.
Electrical connection
• The appliance must be earthed.
• Always use a correctly installed
shockproof socket.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by
our Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• Do not touch the mains cable or the
mains plug with wet hands.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• This appliance complies with the E.E.C.
Directives.
Water connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes, pipes
not used for a long time, where repair
work has been carried out or new
devices fitted (water meters, etc.), let
the water flow until it is clean and clear.
• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
• Do not use an extension hose if the
inlet hose is too short. Contact the
service centre for the replacement of
the inlet hose.
• You can extend the drain hose to
maximum 400 cm. Contact the service
centre for the other drain hose and the
extension.
Use
WARNING! Risk of injury,
electrical shock, fire, burns or
damage to the appliance.
• This appliance is for household use
only.
• Follow the safety instructions on the
detergent packaging.
• Do not put flammable products or items
that are wet with flammable products
in, near or on the appliance.
• Make sure that all metal objects are
removed from the laundry.
• Do not wash fabrics which are heavily
soiled with oil, grease or other greasy
substances. It can damage rubber
parts of the washing machine. Prewash
such fabrics by hand before loading
them into the washing machine.
• Do not touch the glass door while a
programme is in operation. The glass
can get hot.
Service
• To repair the appliance contact an
Authorised Service Centre.
• Use original spare parts only.
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the
mains electrical and water supplies.
• Cut off the mains electrical cable close
to the appliance and dispose of it.
• Remove the door catch to prevent
children or pets from becoming trapped
in the drum.
• Dispose of the appliance in accordance
with local requirements for the disposal
of Waste Electrical and Electronic
Equipment (WEEE).
4
PRODUCT DESCRIPTION
Appliance overview
1 2 3
5
6
4
1
Worktop
2
Detergent dispenser
3
Control panel
4
Door handle
5
Rating plate
6
Feet for levelling the appliance
CONTROL PANEL
Control panel description
90°
60°
40°
30°
1400
1200
800
97621 3 4 5 8
Kurz /
Rapide
Buntwäsche / Coton
Buntwäsche / Coton
Pflegeleicht / Synthétiques
Feinwäsche / Délicats
Wolle / Laine
Auffrischen 20 min / Rafraîchir 20'
Mix 20° / Programme Mix 20°
Intensiv /
Intensif
Bügelquick /
Repassage Facile
Spülen /
Rinçage seul
Pumpen /
Essorage
On/Off
ECO
Ende in / Fini dans
1
On/Off button
2
Programme selection touchpad
3
Temperature selection touchpad
4
Spin selection touchpad
5
Options selection touchpad
6
Start/Pause touchpad
7
Ende in/Fini dans touchpad
8
Display
5
9
Door locked indicator
Display
Ende in / Fini dans
A
D
B C
A. The time area:
• : the programme duration
• : the "finish in" time
• : the alarm codes
• : the message of error
• : the programme is completed.
B. The child lock indicator:
• The indicator comes on when you
activate this device.
C. The extra rinse indicator:
• The indicator comes on when you
activate this option.
D. The Ende in/Fini dans touchpad.
PROGRAMME CHART
Programme
Temperature
range
Maximum
load
Maximum
spin speed
Programme description
(Type of load and soil level)
30' @ 30°
30 °C
3 kg
800 rpm
A short cycle for synthetic and delicate items with
light soil level or for items to freshen up.
Buntwäsche/
Coton
90 °C - Cold
9 kg
1400 rpm
White cotton and coloured cotton. Normal soil and
light soil.
Buntwä‐
sche/Coton
ECO
1)
60 °C - 40 °C
9 kg
1400 rpm
White cotton and fast-coloured cotton. Normal soil.
The energy consumption decreases and the time of
the washing programme is extended.
Pflegeleicht/
Synthétiques
60 °C - Cold
3,5 kg
1200 rpm
Synthetic items or mixed fabric items. Normal soil.
Feinwäsche/
Délicats
40 °C - Cold
3,5 kg
1200 rpm
Delicate fabrics such as acrylics, viscose and
mixed fabrics requiring a mild washing. Normal
soil.
Wolle/Laine
40 °C - Cold
2 kg
1200 rpm
Machine washable wool, hand washable wool and
other fabrics with «hand washing» care symbol
2)
.
6
Programme
Temperature
range
Maximum
load
Maximum
spin speed
Programme description
(Type of load and soil level)
Daunen/Couette
60 °C - Cold
3 kg
800 rpm
Special programme for one synthetic blanket, du‐
vet, bedspread and so on.
Mix 20°/
Programme Mix
20°
20 °C
2 kg
1200 rpm
Special programme for cotton, synthetic and mixed
fabrics with light soil. Set this programme to decrease
the energy consumption. Make sure that the deter‐
gent is for low temperature in order to have good
washing results
3)
.
1)
Standard programmes for the Energy Label consumption values. According to regulation 1061/2010,
these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton pro‐
gramme». They are the most efficient programmes in terms of combined energy and water consumption for
washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the se‐
lected programme.
2)
During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or
doesn't rotate properly, but this is normal for this programme.
3)
No temperature indicator is on .
Programme options compatibility
Pro‐
gramme
Kurz/
Rap‐
ide
1)
In‐
ten‐
siv/
In‐
ten‐
sif
Bü‐
gel‐
quick/
Re‐
pas‐
sage
Facile
Spü‐
len/
Rin‐
çage
seul
Pump‐
en/
Essor‐
age
30' @ 30° ■ ■ ■ ■
Buntwä‐
sche/
Coton
■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Buntwä‐
sche/
Coton
ECO
■ ■ ■ ■ ■ ■ ■ ■
Pflege‐
leicht/
Synthé‐
tiques
■ ■ ■ ■ ■ ■ ■ ■ ■ ■
7
Pro‐
gramme
Kurz/
Rap‐
ide
1)
In‐
ten‐
siv/
In‐
ten‐
sif
Bü‐
gel‐
quick/
Re‐
pas‐
sage
Facile
Spü‐
len/
Rin‐
çage
seul
Pump‐
en/
Essor‐
age
Feinwä‐
sche/Déli‐
cats
■ ■ ■ ■ ■ ■ ■ ■ ■
Wolle/
Laine
■ ■ ■ ■ ■ ■
Daunen/
Couette
■ ■ ■ ■ ■ ■
Mix 20°/
Pro‐
gramme
Mix 20°
■ ■ ■ ■ ■ ■ ■
1)
When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to keep
the full load but the washing results can be unsatisfactory. Recommended load: cotton: 4,5 kg, synthetics and
delicates: 2,5 kg.
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant stand‐
ards. Different causes can change the data: the quantity and type of laun‐
dry and ambient temperature. Water pressure, the supply voltage and the
temperature of inlet water may also affect the washing programme dura‐
tion.
Technical specifications may be changed without prior notice to improve
the quality of product.
At the start of the programme, the display shows the programme duration
for the maximum load capacity.
During the washing phase the programme duration is automatically cal‐
culated and can be greatly reduced if the laundry load is lower than the
maximum load capacity (e.g. Cotton 60°C, maximum load capacity 9 kg,
the programme duration exceeds 2 hours; actual load 1 kg, the pro‐
gramme duration will be less than 1 hour).
When the appliance is calculating the real programme duration a dot
flashes in the display.
8
Programmes Load
(kg)
Energy
consump‐
tion (kWh)
Water
consump‐
tion (litre)
Approxi‐
mate pro‐
gramme
duration
(minutes)
Remain‐
ing mois‐
ture (%)
1)
Buntwäsche/Coton
60°C
9 1,58 84 175 53
Buntwäsche/Coton
40°C
9 1,01 82 174 53
Pflegeleicht/
Synthétiques 40°C
3,5 0,74 61 122 35
Feinwäsche/Déli‐
cats 40°C
3,5 0,54 62 74 35
Wolle/Laine
30°C
2)
2 0,42 62 70 30
Standard cotton programmes
Standard 60°C cot‐
ton
9 1,03 49 220 53
Standard 60°C cot‐
ton
4,5 0,77 40 187 53
Standard 40°C cot‐
ton
4,5 0,62 40 181 53
1)
At the end of spin phase.
2)
Not available for some models.
Off Mode (W) Left On Mode (W)
0.48 0.48
The information given in the chart above is compliant with the EU Commission regulation
1015/2010 implementing directive 2009/125/EC .
OPTIONS
Temperature
With this option you can change the
default temperature.
Indicator = cold water.
The indicator of the set temperature
comes on.
Spin
With this option you can change the
default spin speed.
The indicator of the set speed comes on.
Additional spin options:
No Spin
9
• Set this option to deactivate all spin
phases. Only the drain phase is
available.
• The related indicator comes on.
• Set this option for very delicate fabrics.
• The rinses phase uses more water for
some washing programmes.
Rinse Hold
• Set this option to prevent the laundry
creases.
• The related indicator comes on.
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the
laundry creases.
• The door stays locked. You must drain
the water to unlock the door.
To drain the water refer to ‘At
the end of the programme’.
Kurz/Rapide
With this option you can decrease the
programme duration.
Use this option for items with light soil or
items to refresh.
The related indicator comes on.
Intensiv/Intensif
With this option you can wash very soiled
laundry.
The washing cycle lasts longer with this
option.
The related indicator comes on.
Bügelquick/Repassage Facile
The appliance carefully washes and spins
the laundry to prevent the creases.
The appliance decreases the spin speed,
uses more water and adapts the
programme duration to the type of
laundry.
The related indicator comes on.
Spülen/Rinçage seul
With this option you can perform only a
last rinse of a selected washing
programme.
If you set also the Extra Rinse function
( ) the appliance adds two or more
rinses.
The related indicator comes on.
Pumpen/Essorage
With this option you can perform the spin
and drain cycle.
The spin phase is suitable to the washing
programme you set.
If you set also the No Spin ( )
option, the appliance only
drains.
Ende in/Fini dans
With this option you can set the number of
hours in which you would like your
washing programme to be completed.
You can set from minimum 3 hours to
maximum 20 hours.
The display shows the number of hours
and the indicator above the button is
on.
Extra Rinse
With this option you can add some rinses
to a washing programme.
Use this option for persons allergic to
detergents and in areas where the water
is soft.
The related indicator comes on.
1)
1)
See in "Settings" how to activate this option.
10
SETTINGS
Extra Rinse
With this option you can permanently have
an extra rinse when you set a new
programme.
• To activate/deactivate this option
touch the buttons and at the
same time until the indicator comes
on/goes off.
Child Lock
With this option you can prevent that the
children play with the control panel.
• To activate/deactivate this option,
touch the buttons and at the
same time until the indicator comes
on/goes off.
Activate this option after you touch the
button : the buttons are locked (except
for the button ) .
This option stays active even
when you switch off the
appliance.
Acoustic signals
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic
signals, touch the buttons and at the
same time for 4 seconds.
If you deactivate the acoustic
signals, they continue operate
when the appliance has a
malfunction.
BEFORE FIRST USE
1. Put a small quantity of detergent in the
compartment for washing phase.
2. Set and start a programme for cotton
at the highest temperature without
laundry.
This removes all possible dirt from the
drum and the tub.
DAILY USE
WARNING! Refer to Safety
chapters.
Loading the laundry
1. Open the appliance door
2. Shake the items before you put them
in the appliance.
3. Put the laundry in the drum, one item
at a time.
Make sure not to put too much laundry in
the drum.
4. Close the door firmly.
11
CAUTION! Make sure that no
laundry stays between the seal
and the door. There is a risk of
water leakage or damage to
the laundry.
Washing heavily oiled, greasy
stains could cause damage
rubber parts of the washing
machine.
Using detergent and additives
1. Measure out the detergent and the
fabric conditioner.
2. Put the detergent and the fabric
conditioner into the compartments.
3. Carefully close the detergent drawer
Detergent compartments
Detergent compartment for
washing phase.
If you use liquid detergent, put
it immediately before you start
the programme.
Compartment for liquid addi‐
tives (fabric conditioner,
starch).
CAUTION! Do
not exceed the
MAX level.
Flap for powder or liquid de‐
tergent.
Liquid or powder detergent
1.
A
2.
12
3.
B
4.
• Position A for powder detergent (factory setting).
• Position B for liquid detergent.
When you use the liquid detergent:
• Do not use gelatinous or thick liquid detergents.
• Do not put more liquid then the maximum level.
• Do not set the delay start (or Finish in option).
Activating the appliance
Press and hold for a couple of seconds
the On/Off button to activate or deactivate
the appliance.
A tune sounds when the appliance is
activated.
The display shows the word On.
Setting a programme
1. Touch the programme button and
set the programme:
• The indicator of the button
flashes.
• The display shows the programme
duration.
2. If necessary, change the temperature
and the spin speed or add available
options. When you activate an option,
the indicator of the set option comes
on.
If you set something incorrect,
the display shows the message
.
Starting a programme without
the Ende in/Fini dans option
Touch the button .
• The indicator of the button
stops to flash and stays on.
• The programme starts, the door
locks, the indicator is on.
• The drain pump can operate for a
short time at the beginning of the
washing cycle.
After approximately 15 minutes
from the start of the
programme:
• The appliance adjusts
automatically the
programme duration agree
with the laundry load.
• The display shows the new
value.
Starting a programme with the
Ende in/Fini dans option
1. Touch the button again and again
to choose the number of hours in
which you want the washing cycle to
be finished.
13
The display shows the number of hours
you set (e.g. ) and the indicator above
the button is on to show that his option
is active.
2. Touch the button :
• The door is locked.
• The appliance starts the
countdown.
• When the countdown is completed,
the programme starts automatically.
You can cancel or change the
set of the Ende in/Fini dans
option before you touch the
button . After touching the
button you can only cancel
the Ende in/Fini dans option.
To cancel the the Ende in/Fini dans
option:
a. Touch the button to set the
appliance to pause. The indicator
of button flashes.
b. Touch the button until the
indicator above this button goes
off.
Touch the button
again to start
the programme immediately.
Interrupting a programme and
changing the options
You can change only some options before
they operate.
1. Touch
.
The indicator of this button flashes.
2. Change the options. If you change any
option the Ende in/Fini dans option (if
set) will be disabled.
3. Touch again.
The programme continues.
Cancelling a programme
1. Press the button for some seconds
to cancel the programme and to
deactivate the appliance.
2. Press the same button again to
activate the appliance. Now, you can
set a new washing programme.
Before starting the new
programme the appliance could
drain the water. In this case,
make sure that the detergent is
still in the detergent
compartment, if not fill the
detergent again.
Opening the door
While a programme (or the ) operates,
the appliance door is locked. The indicator
is on.
CAUTION! If the temperature
and level of the water in the
drum are too high, you cannot
open the door.
To open the door during the first
minutes of the cycle (or when the
operates) :
1. Touch the button to pause the
appliance.
2. Wait until the indicator goes off.
3. You can open the door.
4. Close the door and touch the button
again. The programme (or the )
continues.
At the end of the programme
• The appliance stops automatically.
• The acoustic signal operates (if it is
activated).
• In the display comes on.
• The indicator of the button goes off.
• You can open the door.
• Remove the laundry from the
appliance. Make sure that the drum is
empty.
• Press the button for some seconds
to deactivate the appliance.
• Close the water tap.
14
• Keep the door and the detergent
drawer ajar, to prevent the mildew and
odours.
The washing programme is completed,
but there is water in the drum:
• The drum turns regularly to prevent the
creases in the laundry.
• The indicator flashes to remind you
to drain the water.
• The door lock indicator is on. The
indicator of button flashes. The
door stays locked.
• You must drain the water to open the
door.
Draining the water:
1. To drain the water.
• Touch the button . The
appliance drains the water and
spins with the maximum spin speed
for selected washing programme.
• Alternatively, touch the button to
change the spin speed and then
touch the button . The appliance
drains the water and spins. If you
set , the appliance only drains.
2. Press the button for some seconds
to deactivate the appliance.
The appliance drains and spins
automatically after
approximately 18 hours (except
for Wool programme).
AUTO-OFF option
The AUTO-OFF stand-by option
automatically deactivates the appliance to
decrease the energy consumption. All the
indicators and the display go off when :
• You do not use the appliance for 5
minutes before you touch .
Press the button to activate the
appliance again.
• After 5 minutes from the end of the
washing programme.
Press the button to activate the
appliance again.
The display shows the end of the last
set programme.
Touch the button
if you want to set a
new cycle.
HINTS AND TIPS
The laundry load
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are
on the laundry care labels.
• Do not wash white and coloured items
together.
• Some coloured items can discolour
with the first wash. We recommend that
you wash them separately for the first
times.
• Button up pillowcases, close zippers,
hooks and poppers. Tie up belts.
• Empty the pockets and unfold the
items.
• Turn multilayered fabrics, wool and
items with painted illustrations inside
out.
• Remove hard stains with a special
detergent.
• Wash and pre-treat heavy soil stains
before putting items in drum
• Be careful with the curtains. Remove
the hooks and put the curtains in a
washing bag or pillowcase.
• Do not wash laundry without hems or
with cuts. Use a washing bag to wash
small and/or delicate items (e.g.
underwired bras, belts, tights, etc. ).
• A very small load can cause balance
problems with the spin phase. If this
occurs, adjust manually the items in the
tub and start the spin phase again.
Stubborn stains
For some stains, water and detergent is
not sufficient.
We recommend that you pre-treat these
stains before you put the items in the
appliance.
15
Special stain removers are available. Use
the special stain remover that is applicable
to the type of stain and fabric.
Detergents and additives
• Only use detergents and additives
specially made for washing machines:
– powder detergents for all types of
fabric,
– powder detergents for delicate
fabrics (40 °C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60
°C max) for all types of fabric, or
special for woollens only.
• Do not mix different types of
detergents.
• To help the environment, do not use
more than the correct quantity of
detergent.
• Obey the instructions that you find on
the on packaging of these products.
• Use the correct products for the type
and colour of the fabric, the programme
temperature and the level of soil.
• If your appliance does not have the
detergent dispenser with the flap
device, add the liquid detergents with a
dosing ball (supplied by the detergent's
manufacturer).
Ecological hints
• Always start a washing programme
with the maximum load of laundry
allowed.
• If necessary, use a stain remover when
you set a programme with a low
temperature.
• To use the correct quantity of
detergent, check the water hardness of
your domestic system. Refer to "Water
hardness".
Water hardness
If the water hardness in your area is high
or moderate, we recommend that you use
a water softener for washing machines. In
areas where the water hardness is soft it
is not necessary to use a water softener.
To know the water hardness in your area,
contact your local water authority.
Use the correct quantity of the water
softener. Obey the instructions that you
find on the packaging of the product.
CARE AND CLEANING
WARNING! Refer to Safety
chapters.
External cleaning
Clean the appliance with soap and warm
water only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
Descaling
If the water hardness in your area is high
or moderate, we recommend that you use
a water descaling product for washing
machines.
Regularly examine the drum to prevent
limescale and rust particles.
To remove rust particles use only special
products for washing machines. Do this
separately from the laundry wash.
Always obey the instructions
that you find on the packaging
of the product.
Maintenance wash
With the low temperature programmes it is
possible that some detergent stays in the
drum. Perform a maintenance wash
regularly. To do this:
• Remove all laundry from the drum.
16
Door seal
Regularly examine the seal and remove
all objects from the inner part.
Cleaning the detergent dispenser
1. 2.
3. 4.
17
Cleaning the inlet hose and the valve filter
1.
1
2
3
2.
3. 4.
45°
20°
Frost precautions
If the appliance is installed in an area
where the temperature can be less than 0
°C, remove the remaining water from the
inlet hose and the drain pump.
Do this procedure also when
you want to do the emergency
drain.
1. Disconnect the mains plug from the
mains socket.
2. Close the water tap.
3. Remove the water inlet hose.
4. Remove the drain hose from the rear
support and unhook it from sink or
spigot.
1
2
5. Put the ends of the drain and inlet
hose in a container. Let the water flow
out of the hoses.
6. When no more water flows, install the
inlet hose and the drain hose again.
WARNING! Make sure that the
temperature is more than 0 °C
before you use the appliance
again. The manufacturer is not
responsible for damages
caused by low temperatures.
18
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
Introduction
The appliance does not start or it stops
during operation.
First try to find a solution to the problem
(refer to the table). If the problem persists,
contact the Authorised Service Centre.
With some problems, the acoustic
signals operate and the display shows
an alarm code:
• - The appliance does not fill with
water properly.
• - The appliance does not drain
the water.
• - The appliance door is open or
not closed correctly. Please check the
door!
If the appliance is
overloaded, remove some
items from the drum and/or
keep pressed the door and
push the button at the
same time until the indicator
stops flashing (see the
picture below).
• - The mains supply is unstable.
Wait until the mains supply is stable.
• - No communication between
electronic elements of the appliance.
Switch off and switch on again.
WARNING! Deactivate the
appliance before you do the
checks.
Possible failures
Problem Possible solution
The programme does
not start.
• Make sure that the mains plug is connected to the mains
socket.
• Make sure that the appliance door is closed.
• Make sure that there is not a damaged fuse in the fuse box.
• Make sure that the Start/Pause has been pressed.
• If the delay start is set, cancel the setting or wait for the end of
countdown.
• Deactivate the Child Lock function if it is on.
19
Problem Possible solution
The appliance does not
fill with water properly.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low.
For this information, contact your local water authority.
• Make sure that the water tap is not clogged.
• This problem may be caused by the filter of the inlet hose or
the valve drain filter which may be clogged. Refer to “Care
and cleaning”. If problem remains please contact the Author‐
ised Service Centre.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the connection of the water inlet hose is cor‐
rect.
The appliance does not
drain the water.
• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Make sure that the connection of the drain hose is correct.
• Set the drain option if you set a programme without drain
phase.
• Set the drain option if you set an option which ends with water
in the drum.
• This problem may be caused by the clogged drain filter.
Please contact the Authorised Service Centre.
The spin phase does not
operate or the washing
cycle lasts longer than
usually.
• Adjust manually the items in the tub and start the spin phase
again. This problem may be caused by balance problems.
• Set the spin option.
• Set the drain option if you set an option which ends with water
in the drum.
• This problem may be caused by the clogged drain filter.
Please contact the Authorised Service Centre.
There is water on the
floor.
• Make sure that the couplings of the water hoses are tight and
there is not water leakages.
• Make sure that the water inlet hose and the drain hose have
no damages.
• Make sure you use the correct detergent and the correct
quantity of it.
You cannot open the ap‐
pliance door.
• Make sure that the washing programme is finished.
• Set the drain or the spin option if there is water in the drum.
• Do the emergency drain procedure. See "Frost precautions"
(in "Care and Cleaning" chapter).
The appliance makes an
unusual noise.
• Make sure the levelling of the appliance is correct. Refer to
'Installation instruction'.
• Make sure that the packaging and/or the transit bolts are re‐
moved. Refer to 'Installation instruction'.
• Add more laundry in the drum. The load may be too small.
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Novamatic WA914E Manuel utilisateur

Novamatic
Marque
Novamatic
Modèle
WA914E
Catégorie
Machines à laver
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents