Yamaha NS-B310 Le manuel du propriétaire

Marque: Yamaha

Modèle: NS-B310

Catégorie: Mur

Taper: Le manuel du propriétaire

Ce manuel convient également à

NS-C310

NS-B310

NS-C310

Speaker

Enceinte

UTG

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUAL DE INSTRUCCIONES

i En

Thank you for selecting this YAMAHA product.

Read this before using the speaker.

• To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

• Install the speaker in a cool, dry, clean place - away from

windows, heat sources, sources of excessive vibration, dust,

moisture and cold. Avoid sources of electrical noise

(transformers, motors). To prevent fire or electrical shock, do

not expose this unit to rain or water.

• To prevent the enclosure from warping or discoloring, do not

place the speaker where it will be exposed to direct sunlight or

excessive humidity.

• Do not place the following objects on the speaker:

Glass, china, small metallic etc.

If glass, etc., falls as a result of vibration and breaks, it may

cause personal injury.

A burning candle, etc.

If the candle falls as a result of vibrations, it may cause fire

and personal injury.

A vessel with water in it

If the vessel falls as a result of vibrations and water spills, it

may cause damage to the speaker, and/or you may get an

electric shock.

• Do not place the speaker where foreign material such as

dripping water. It might cause fire, damage to this unit, and/or

personal injury.

• Do not place the speaker where it is liable to be knocked over

or struck by falling objects. Stable placement will also ensure

better sound performance.

• Placing the speaker on the same shelf or rack as the turntable

can result in acoustical feedback.

• Never put a hand or a foreign object into the port located on the

rear of the speaker, as this might cause personal injury and/or

damage to the speaker.

• When moving the speaker, do not hold the port, as it might

cause personal injury and/or damage to the speaker.

• Any time you notice distortion, reduce the volume control on

your amplifier. Never allow your amplifier to be driven into

“clipping.” Otherwise the speaker may be damaged.

• When using an amplifier with a rated output power higher than

the nominal input power of the speaker, care should be taken

never to exceed the speaker’s maximum input.

• Do not attempt to clean the speaker with chemical solvents, as

this might damage the finish. Use a clean, dry cloth.

• Do not attempt to modify or repair the speaker. Contact

qualified YAMAHA service personnel when any service is

needed. The cabinet should never be opened for any reasons.

• Secure placement and installation is the owner’s

responsibility. YAMAHA shall not be liable for any

accident caused by improper placement or installation of

speakers.

PRECAUTIONS

Information for Users on Collection and Disposal of Old

Equipment

This symbol on the products, packaging, and/

or accompanying documents means that used

electrical and electronic products should not

be mixed with general household waste.

For proper treatment, recovery and recycling

of old products, please take them to applicable

collection points, in accordance with your

national legislation and the Directives 2002/

96/EC.

By disposing of these products correctly, you

will help to save valuable resources and

prevent any potential negative effects on

human health and the environment which

could otherwise arise from inappropriate

waste handling.

For more information about collection and

recycling of old products, please contact your

local municipality, your waste disposal

service or the point of sale where you

purchased the items.

[Information on Disposal in other Countries

outside the European Union]

This symbol is only valid in the European

Union. If you wish to discard these items,

please contact your local authorities or dealer

and ask for the correct method of disposal.

English

1 En

■ Using as 2ch stereo speakers

Better stereo images will be obtained when the speakers are

slightly angled in towards the listeners.

■ Using as front speakers and surround

speakers in a surround system

Position the speakers on both sides of the TV. The positioning of

speakers is important, since this dictates the overall sound quality

of the surround system. Set up the speakers on the basis of your

listening position by following the owner’s manual supplied with

your amplifier.

And mount the speakers on a wall or place the speakers on a shelf.

Determine the best position by following the owner’s manual

supplied with your amplifier.

■To mount the speakers on a wall by using

the attached mounting bracket

Fasten screws into a firm wall or wall support as shown in the

figure, and hang the holes of the mounting bracket on the

protruding screws.

* Make sure that the screws are secured in the narrow sections

of the holes.

Note

Placing this unit too close to a CRT TV set might impair

picture color or create a buzzing noise. Should this happen,

move the speaker away (more than 20 cm (7-7/8”)) from the

TV set.

When using a PDP or LCD TV, it would not happen.

WARNING

• NS-B310 weighs 1.6 kg (3 lbs. 8 oz.). Do not mount it on thin

plywood or a wall with soft surface material. If mounted,

the screws may come out and the speaker may fall. This may

damage the speaker, or cause personal injury.

• Do not install the speaker on a wall with nails, adhesives, or

any other unstable hardware. Long term use and vibrations

may cause it to fall.

• To avoid accidents resulting from tripping over loose

speaker cables, fix them securely to the floor or wall.

SUPPLIED ACCESSORIES

(Only for NS-C310)

PLACING THE SPEAKERS

For NS-B310

Fastener × 2

NS-B310

Front

NS-C310

NS-B310

Surround

Subwoofer

You can also use the screw holes on the bottom of the speaker

for installing the speaker using a commercially available

speaker bracket (if you do not use the attached mounting

bracket).

Diameter. 3.5 to 4 mm

(1/8” to 3/16”)

3 mm

(1/8”)

Min.

20 mm

(13/16”)

Wall or wall

support

Tapping screw

(Available at the hardware store)

26 mm

(1”)

Screw holes

Diameter: 6 mm (1/4”)

Hole Depth: 14 mm (9/16”)

60 mm (2-3/8”)

2 En

■ Using as center speaker

Place the speaker on a TV rack or other stable surface. To prevent

the speaker from falling down, attach the fasteners provided in

each corner of the speaker’s underside.

■ To mount the speakers on a wall by using

the attached mounting bracket

Fasten screws into a firm wall or wall support as shown in the

figure, and hang the holes of the mounting bracket on the

protruding screws.

Note

Placing this unit too close to a CRT TV set might impair

picture color or create a buzzing noise. Should this happen,

move the speaker away (more than 20 cm (7-7/8”)) from the

TV set.

When using a PDP or LCD TV, it would not happen.

WARNING

• NS-C310 weighs 2.9 kg (6 lbs. 6 oz.). Do not mount it on thin

plywood or a wall with soft surface material. If mounted,

the screws may come out and the speaker may fall. This may

damage the speaker, or cause personal injury.

• Do not touch the adhesive surface after peeling off the seal

as this will weaken its adhesive strength.

• Thoroughly wipe clean the surface where the fasteners are

to be attached. Note that adhesive strength is weakened if

the surface is dirty, oily or wet, and that this may cause the

center speaker to drop.

• Do not install the speaker on a wall with nails, adhesives, or

any other unstable hardware. Long term use and vibrations

may cause it to fall.

• To avoid accidents resulting from tripping over loose

speaker cables, fix them securely to the floor or wall.

For NS-C310

Fastener

Make sure that the screws are secured in the

narrow sections of the holes.

320 mm

(12-9/16”)

Diameter. 3.5 to 4 mm

(1/8” to 3/16”)

3 mm

(1/8”)

Min.

20 mm

(13/16”)

Tapping screw

(Available at the hardware store)

Wall or wall

support

English

3 En

Before making connections, make sure that the amplifier is

switched off.

• Connect the screw-type input terminals at the rear of the

speakers to the speaker output terminals of the amplifier (or

receiver) with the speaker cable.

• Connect the (+) terminals on the amplifier (or receiver) to the

(+) terminal of each speaker, making sure to confirm the color-

coded wire of the cable at each end. Use the other wire of the

cable to connect the (–) terminals of the components.

• Connect one speaker to the left (marked L) terminals of your

amplifier, and another speaker to the right (marked R)

terminals, making sure not to reverse the polarity (+, –). If one

speaker is connected with reversed polarity the sound will be

unnatural and lack bass.

■How to connect

1 Loosen the knob.

2 Remove 10 mm (3/8”) of insulation from each end of the

cables, and twist the exposed conductors together neatly and

tightly, as shown below.

3 Insert the bare wire.

4 Tighten the knob and secure the cables.

Test the firmness of the connection by pulling lightly on the

cables at the terminal.

Notes

• Do not let the bare speaker wires touch each other as this

could damage the speaker or the amplifier, or both.

• Do not insert the insulation into the hole. Sound may not be

produced.

■When using a banana plug

Note

Do not take off this cover unless using a banana plug.

1 Remove the cover by pulling it toward you.

2 Tighten the terminal knob.

3 Simply insert the banana plug into the terminal.

CONNECTIONS TO YOUR

AMPLIFIER

Loosen

Black (–)

Tighten

Red (+)

NS-B310

Amplifier or

receiver

NS-C310

NS-B310

Loosen

Black (–)

Tighten

Red (+)

Good No Good

10 mm

(3/8 ”)

Banana plug

Cover

4 En

The front cover is attached to protect the speaker, but you can

remove it if necessary.

The front cover is fixed by magnets. Hold the speaker with one

hand, and pull the front cover gently with the other to remove it.

Notes

• When removing the cover, be careful that you don't touch

the drive units, and don't exert excessive force with any

tools.

• There are magnets on the reverse side of the front cover. Do

not place a front cover close to objects that might be affected

by magnets, such as CRT TV, clock, magnetic card,

diskette, etc., after removing it.

NS-B310

Type .................... full-range acoustic suspension speaker system

Non-Magnetic shielding type

Driver.......................................8 cm (3-1/8”) cone full-range × 2

Impedance...............................................................................6 Ω

Frequency Response ............................80 Hz to 35 kHz (-10 dB)

to 50 kHz (-30 dB)

Nominal Input Power........................................................... 40 W

Maximum Input Power ...................................................... 120 W

Sensitivity ........................................................... 87 dB/2.83 V/m

Dimensions (W × H × D)............................ 107 × 200 × 127 mm

(4-3/16” × 7-7/8” × 5”)

Weight............................................................1.6 kg (3 lbs. 8 oz.)

NS-C310

Type ..........................2-way acoustic suspension speaker system

Non-Magnetic shielding type

Driver...................................... 6.5 cm (2-9/16”) cone woofer × 4

3 cm (1-3/16”) soft dome tweeter

Impedance...............................................................................6 Ω

Frequency Response ........................... 90 Hz to 45 kHz (-10 dB)

to 100 kHz (-30 dB)

Nominal Input Power........................................................... 40 W

Maximum Input Power ..................................................... 120 W

Sensitivity .......................................................... 90 dB/2.83 V/m

Crossover Frequency ......................................................... 6 kHz

Dimensions (W × H × D).............................. 440 × 94 × 125 mm

(17-5/16” × 3-11/16” × 4-15/16”)

Weight............................................................2.9 kg (6 lbs. 6 oz.)

• Specifications subject to change without notice due to product

improvements.

• Care should be taken not to exceed the input power values noted

above.

• A speaker cable is not included with this model.

REMOVING THE FRONT

COVER

NS-B310

NS-C310

SPECIFICATIONS

Taking care of the speaker

When you wipe this unit, do not use chemical solvents (e.g.,

alcohol or thinners, etc.): this might damage the finish. Use a

clean, dry cloth. For difficult soils, dampen a soft cloth in

water, wring it out, and then wipe with the cloth.

English

5 En

Limited Guarantee for European Economic Area (EEA) and Switzerland

Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from

whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our

website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).

The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha

undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge

for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been

discontinued or is considered uneconomic to repair.

Conditions

1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a

statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the

product may be returned at the customer’s expense.

2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.

3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.

4. The following are excluded from this guarantee:

a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.

b. Damage resulting from:

(1) Repairs performed by the customer himself or by an unauthorised third party.

(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to

ensure the product is adequately packaged when returning the product for repair.

(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the

proper use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in

force in the country where it is used.

(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.

(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.

(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety

standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.

(7) Non AV (Audio Visual) related products.

(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or

http://www.yamaha-uk.com/ for U.K. resident.)

5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.

Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the product.

7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.

8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising

from their sales/purchase contract.