Cinta selladora para rosca
Ruban pour tuyau
Pipe Tape
Destornillador cruciforme
Tournevis Phillips
Phillips ScrewdriverAdjustable Wrench
Clé à molette
Llave ajustable
MFF-VARK1-CP
MFF-VARK1-BN
MFF-VARK1-ORB
Varenne
Pull-down Kitchen Faucet
Installation/Installation/
Instalación
CUSTOMER SERVICE
TOLL-FREE 1-877-482-5422
Tools You Will Need / Outils dont vous aurez besoin / Herramientas necesarias
Replacement Parts / Pièces de rechange / Repuestos
SAFETY TIPS
• If you use soldering for the installation of the faucet, the seats, cartridges and washers will have to be removed
before using flame. Otherwise, warranty will be void on those parts.
• Cover your drain to avoid losing parts.
• 0℃~55℃.
CONSIGNES DE SÉCURITÉ
• Si vous posez le robinet par brasage, il est essentiel de retirer les sièges, les cartouches et les rondelles avant
d’appliquer la flamme, faute de quoi la garantie sur ces pièces sera annulée.
• Couvrez le drain pour ne pas perdre des pièces.
• 0℃~55℃.
CONSEJOS DE SEGURIDAD
• En el caso de utilizar soldadura para instalar el grifo, remueva los asientos, cartuchos y arandelas antes de usar la
llama. De lo contrario, se anulará la garantía para esos componentes.
• Tape la boca del desagüe para prevenir la pérdida de piezas pequeñas.
• 0℃~55℃.
Revised 4-2018
MFF-VARK1-CP - CHROME
MFF-VARK1-BN - BRUSHED NICKEL
MFF-VARK1-ORB - OIL RUBBED BRONZE
Revised 4-2018
1
2
3
4
5
6
7
10
9
8
14
13
12
11
15 1716
18
19
20
No. Description Part No.
1
Hose Guide 5L0082000PL0
2 Sprayer 5F0006701CP/AP/HA0
3
Connector Assembly 5J0023000NT0
4
O-
Ring Set 5Y0110500PL0
5
Weight 5X0M0063PL
6
Spray Hose 5G0M0142CP/AP/HA7
7
Base Assembly
5Y0110600PL0
8
Mounting Hardware Assembly
9Q0979CP/AP/HA
9
Hose Guide
53013138PL
10
Nuts 6B005801NT
11 Retainer Clip 5M0P0132PL
12 Quick Connector 5L0P0440PL
13
Check Valve 5D0M0003PL
14 O-Ring
52006913PL
15
Ceramic Disc Cartridge
52007014PL
16
Retainer Nut
5N0C0697NT
17
Trim Cap 5L0C0283CP/AP/HA
18 Handle
5C0073300CP/AP/HA0
19
20
Screw & Button
Allen Key 2.5mm
5Y0187900PL0
51002812NT
MFF-VARK1-CP
MFF-VARK1-BN
MFF-VARK1-ORB
Installation/Installation/Instalación
Revised 4-2018 Revised 4-2018
Press the button of the quick connector
and connect it with the hose.
5
3
Install washer, gasket and mounting nuts
onto the shank to cover the mounting
hole.
Tighten the mounting nut.
Remove the quick connector.
1
Install the faucet through the mounting
hole.
2 7a
Turn on the handle and press the spray
head button at the position as the arrow
shown , check for the spray function.
This position is for bubble water.
Use supply hoses (not included) to
connect the cold and hot copper inlets
to angle valves. Use wrench to tighten
the coupling nuts.
Turn on water supplies and check all
connections for leaks.
6
Press the spray head button at the
position as the arrow shown , check for
the spray function.
This position is for spray water.
7b
Fasten the weight to the stretching hose
with screws, and then install the quick
connector on the outlet pipe.
4
-
1
-
2
Fontaine by Italia MFF-VARK1-ORB Guide d'installation
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Fontaine by Italia MFF-AMC1-ORB Guide d'installation
-
Fontaine by Italia MFF-CHAC1-CP Guide d'installation
-
-
-
Fontaine by Italia MFF-VARC1-ORB Guide d'installation
-
-
-
-
-