Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
HARDWARE
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could
result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in
coastal areas clean all external surfaces of the xture once every two weeks with a wet cloth.
: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus
pour ce produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie.
Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un
chion humide.
1
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Nov. 2023
INSTALLATION INSTRUCTIONS
WS-83422 WS-83432
A
B
Wire Connector
Qty: 3pcs+1 Extra
Mounting Screw
Qty: 1 Extra
7. Secure the xture to the mouting plate use the mounting screw (B).
CONNECTING THE WIRES (Fig. 2)
6. Connect the driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly
to the mounting plate using the GND screw provided. After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the xture, take down the mounting plate.
5. Secure the mounting plate to the junction box using standard junction box screws that comes with the junction box.
Note: (i) using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii) The side of the mounting back plate marked “GND” must face out.
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
COMPLETING THE INSTALLATION
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Nov. 2023 2
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
WS-83422 WS-83432
Mounting Plate Dimensions
4000K 3500K 3000K 2700K
Fig. 3 4CCT Switch
4. Set color temperature at this stage. The xture can switch between four color temperatures (2700K,3000K, 3500K,4000K), which can be
adjusted to your preference using the 4CCT switch (Fig. 3) mounted on the mounting plate.
Note: the switch comes with a detachable cover, remove the cover prior to adjusting the color reattach the cover after adjustment is made.
4 1/2”
Junction Box
Mounting Screw
B
Mounting Back Plate
Junction Box Screw
Wire Connector
A
Fixture
Decorate plate
4CCT Switch
Driver
Decorate plate
4CCT Switch Cover
8. The decorative board adopts the magnetic quick installation method. Buckle the safety rope before the installation of the decorative board,
and then align with the wall box.
-
1
-
2
WAC Lighting WS-83432 Mode d'emploi
- Taper
- Mode d'emploi
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
WAC Lighting FM-37416 Mode d'emploi
-
-
-
-
-
-
-
-
-