Modern Forms PD-W28515 Balthus Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
285-Outdoor Wall Sconce
PD-W28515
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN. 2022
CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Wire Connector
Qty: 3pcs+1 Extra
A
Mounting Screw
Qty:1 Extra
BE
Allen Screw
Qty: 1 Extra
Rubber Gasket
Qty:1 Extra
C
Alle Wrench
Qty: 1pcs
D
2
INSTALLATION INSTRUCTIONS
285-Outdoor Wall Sconce
PD-W28515
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN. 2022
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
3x12"Rods
Junction Box
1x6"Rod
Mounting Plate
Junction Box Screw
Rubber Gasket
Mounting Screw
Swivel
Fixture canopy
Wire Connector Ground Wire
Allen
Wrench
Glass
(RPL-GLA-28516)
Allen Screw
A
B
C
D
E
1 a"
Back Plate Dimensions
1 w"
4 w"
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
4. Secure the mounting plate to the junction box using the screws provided with the junction box.
body, rods and swivel. Make sure all are tightened.
NOTE: The side of the mounting plate marked “GND” must face out.
5. Choose the number of rods suitable for your application. Thread the xture wire through the rods,swivel and canopy.Connect the xture
MOUNTING THE FIXTURE (Fig. 1)
PREPARATION
1. Shut off the power at the circuit breaker and remove existing xture,including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area.Be careful not to lose any small parts necessary for installation.
7. Twist the glass in to the xture and tighten it with allen screw (E) using allan wrench (D).
Note:Caulk the allen screw using silicone for wet location.
CONNECTING THE WIRES (Fig. 2)
COMPLETING THE INSTALLATION FIG.3 FIG.4 Junction Box
Caulking
Turn to down
8. Secure the xture to the mounting plate using the mounting
screw (B) and the rubber gasket (C).
9. For slope ceiling applications, rotate swivel at the top of the
stem to ensure luminaire is aiming down (Fig.3).
10. To prevent moisture from entering the outlet box and causing
a short, use clear caulking (i.e. indoor/outdoor silicone sealant)
to outline the outside of xture back plate (Fig.4).
FIG
. 1
3. Remove the mounting screw (B) and the rubber gasket (C) from the backplate.
6. Connect the xture’s input wires to junction box wires as shown (FIG.2) Make sure that all wire connectors (A) are secue. lf your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect xture’s ground wire directly to the back
plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
-
1
-
2
Modern Forms PD-W28515 Balthus Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms PD-55718 Yolo Mode d'emploi
-
-
-
-
-
-
-
-
-