Modern Forms WS-82310 Rowlings Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
WS-82310
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2022
CAUTION: To prevent electrical shock, ensure electricity has been turned o at the circuit breaker before beginning.
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Wire Connector
Qty: 3pcs+1 Extra
Mounting Screw
Qty:1 Extra
AB
2
INSTALLATION INSTRUCTIONS
WS-82310
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2022
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and mounting back plate from the xture.
S
ecure the mounting back plate to the junction box using
standard junction box screws that comes with the junction box
.
Note (i) using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
4. Connect the driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. Connect the
xture’s ground wire to your outlet box ground wire. After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION
5. Secure the xture to mounting plate with mounting screw (B) .
6. If the alabaster is inclined, please hold the alabaster with both hands to adjust the position appropriately.
DIMMING WIRING INFORMATION (Fig. 3)
7. This xture features electronic low voltage (ELV or TRIAC) or 0-10V dimming capabilities. See notes below for specic dimming wires
information.
8. To utilize ELV or TRIAC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
9. To utilize 0-10V dimming: use wire purple (dim+), pink or gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
Note: Make sure to connect 0-10V prior to power-up the xture in order to allow the 0-10V dimming to function properly.
WS-82310 Mounting back plate
1
3/8"
1
3/4"
Ø
6
7/8"
White - Neutral
Black - Hot
Purple - Dim+
Pink or Gray - Dim-
Red - Fixture+
Black - Fixture-
Junction Box
Wire Connector
A
Mounting Screw
Junction Box Screw
Mounting plate
B
FIG. 1
Alabaster
(RPL-GLA-82310)
Fixture
Driver(Canopy Inside)
-
1
-
2
Modern Forms WS-82310 Rowlings Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms PD-81004 Minx Mode d'emploi
-
-
-
-
-
-
-
-
-