Modern Forms FM-24818 Veloce Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTION
FM-24818
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Jun. 2021Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Modern Forms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
D
A
C
B
2
INSTALLATION INSTRUCTION
FM-24818
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
3. Remove the mounting back plate from the xture.
4. Secure the mounting back plate to the junction box using standard junction box screws that comes with the junction box.
(i)using any other non-original-manufacturer provided junction box screw may result in safety issue.
(ii) The side of the mounting ring marked “GND” must face out.
5. Connect the driver’s input wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secure. If your outlet
box has a green or bare copper ground wire, connect the driver’s ground wire to it. Otherwise, connect the xture’s ground wire
directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
6. Secure the xture by mounting the canopy to the ring of the backplate. Turn and rotate the canopy in the direction of the arrow until
it stops. Fasten the canopy to the mounting backplate using the mounting screw (D).
Jun. 2021Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Modern Forms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Junction box
Mounting back plate
Canopy
Junction Box Screw
Wood screw
Plastic anchor
Driver
Fixture
Wire Connector
A
Mounting Screw
D
B
C
Ø16 3/8"
Ø14 5/8"
2 3/4"
3 1/2"
Mounting Back Plate
-
1
-
2
Modern Forms FM-24818 Veloce Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms WS-50222 Fleur Mode d'emploi
-
-
-
-
-
-
-
-
-