Chief PTSU Manuel utilisateur

PTSU
Chief
Marque
Chief
Modèle
PTSU
Catégorie
Supports de bureau à panneau plat
Taper
Manuel utilisateur
INSTALLATION INSTRUCTIONS
Large Flat Panel Display Table Stand
PTS SERIES
PTS SERIES Installation Instructions
2
DISCLAIMER
CSAV, Inc., and its affiliated corporations and subsidiaries
(collectively, "CSAV"), intend to make this manual accurate and
complete. However, CSAV makes no claim that the information
contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection
with the installation or use of this product. The information
contained in this document is subject to change without notice
or obligation of any kind. CSAV makes no representation of
warranty, expressed or implied, regarding the information
contained herein. CSAV assumes no responsibility for
accuracy, completeness or sufficiency of the information
contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the supporting structure and
mount up to (and including) the display does not exceed
100 lbs (45.36 kg).
DIMENSIONS
[102]
4.00
[18]
.70
[581]
22.88
[360 50.80]
14.17 2.0
TO APPROX.
CENTER OF SCREEN
++
[606]
23.88
[276]
10.86 [176]
6.92
[114]
4.50
NOTE: CUSTOM INTERFACE BRACKET
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR DISPLAY
WILL ADD BETWEEN ½”AND 2” IN DEPTH
AND MAY AFFECT LOCATION OF DISPLAY
ON THE MOUNT.
MEASUREMENTS IN: [MILLIMETERS]
INCHES
WEIGHT CAPACITY: 100 LBS
HEIGHT ADJUSTMENT: 4” IN 1” INCREMENTS
TILT/ROLL: 0°/ 2.5°++
Installation Instructions PTS SERIES
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
PTS SERIES Installation Instructions
4
PARTS
TOOLS REQUIRED FOR INSTALLATION
A (1)
B (1)
C (2)
D (1)
E (1)
3/16"
F (8)
5/16-18 x 5/8" G (4)
5/16-18
3/16"
(Provided) 1/2"
Installation Instructions PTS SERIES
5
ASSEMBLY AND INSTALLATION
WARNING: FAILURE TO PROVIDE ADEQUATE
STRUCTURAL STRENGTH FOR THIS COMPONENT CAN
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE
TO EQUIPMENT! It is the installer’s responsibility to make
sure the structure to which this component is attached can
support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
Attaching Post Assembly to Base Assembly
1. Using four 5/16-18 x 5/8" button head cap screws (F) and
four 5/16-18 Nylock nuts (G), secure post assembly (B) to
base assembly (D). (See Figure 1)
Figure 1
2. Attach edge trim pieces (C) to the base assembly (D). See
Figure 2.
Figure 2
Attaching Faceplate Assembly
1. Align mounting holes in faceplate assembly (A) with holes
in post assembly (B). (See Figure 3)
NOTE: The faceplate assembly can be placed within a four
inch range on the post assembly, dependent on size of
display.
2. Attach faceplate assembly to post assembly using four
5/16-18 x 5/8" button head cap screws (F). (See Figure 3)
Figure 3
Attaching Interface Bracket to Display
1. Attach interface bracket to display following instructions
included with interface bracket kit.
Attaching Display to Mount
1. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in mount. (See Figures 4 and 5)
Figure 4
1
(F) x 4
(G) x 4
(D)
(B)
(C) x 2
2
2
(F) x 4
(A)
(B)
1
PTS SERIES Installation Instructions
6
WARNING: DISPLAY MAY WEIGH IN EXCESS OF 40
LBS! Always use two people and proper lifting techniques
when installing or positioning display on mount.
2. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes. (See Fig. 4 and 5)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Ensure mounting
buttons are completely engaged in mounting holes.
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 5).
Figure 5
Removing Display
1. Disconnect all power/audio/video cables.
2. Remove bolt or padlock from faceplate (if used).
(See Figure 6)
NOTE: The pin may have been used as a more permanent
locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.
3. Pull back on flag on upper mounting hole and press pin
down into "Open" position. (See Figure 6)
WARNING: THE DISPLAY MAY WEIGH IN EXCESS OF
40 LBS EACH! Always use two people and proper lifting
techniques when installing or positioning display.
4. Carefully lift display from mount.
5. Lift up on pin and place flag back against faceplate to return
it to "Closed" position. (See Figure 6)
Figure 6
Adjusting Roll Tension
The faceplate provides 2o roll adjustment. (See Figure 7) Roll
adjustment is accomplished by shifting the faceplate right or left
as needed until the faceplate is level.
Figure 7
1
2
May remove
pin and nut and
move to lower holes
A padlock or bolt
may be placed
through latch holes
3
2
Remove bolt
or padlock
if used
Pin in
"Open"
position -
Pin in
"Closed"
position -
5
move to
"Open"
position to
move to
"Closed"
position
remove
display
after display
is removed.
Installation Instructions PTS SERIES
7
NOTE: Roll tension is preset. If the display does not remain in
the desired position, perform the following roll tension
adjustment procedure.
1. Remove display following the Removing Display section.
2. Remove four 5/16-18 x 5/8" button head cap screws from
back of post assembly (inserted in Step 2 of Attaching
Faceplate Assembly section).
3. Locate roll tension adjustment nut on back of faceplate.
(See Figure 8)
Figure 8
4. Partially loosen or tighten the roll tension adjustment nut as
needed.
5. Re-install the faceplate assembly onto the post assembly
following instructions in Attaching Faceplate Assembly
section.
6. Re-mount the display following instructions in Attaching
Display to Mount section.
Roll Tension
Adjustment Nut
PTS SERIES Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
P+86-755-8996 9226 ; 8996 9236 ; 8996 9220
F+86-755-8996 9217
8800-000016 Rev. F
2007 Chief Manufacturing
www.chiefmfg.com
07/07
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief PTSU Manuel utilisateur

PTSU
Chief
Marque
Chief
Modèle
PTSU
Catégorie
Supports de bureau à panneau plat
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes