Kärcher K 2.110 M Manuel utilisateur

Marque: Kärcher

Modèle: K 2.110 M

Catégorie: Outils de jardin

Taper: Manuel utilisateur

English 2

Español 16

Français 30

5.961-668.0 07/05

K 2.900M

2 English

Model Overview 3

Important Safety Instructions 4

Assembly Instructions 6

Operating Instructions 7

GFCI Instructions 8

Using the Accessories 8

Working with Detergents 9

Shutting Down & Clean Up 10

Care and Maintenance Instructions 11

Winterizing and Long-Term Storage11

Cleaning Tips 12

Troubleshooting 14

Call: 1-800-537-4129 for help or visit

our website:

www.karcher-usa.com/home

Please take a moment to register your

presure washer online at

www.karcher-usa.com/warranty

DANGER

indicates “an imminently hazardous sit-

uation which, if not avoided, will result in

death or serious injury.’’

WARNING

indicates “a potentially hazardous situa-

tion which, if not avoided, could result in

death or injury.’’

CAUTION

indicates “a potentially hazardous situa-

tion which, if not avoided, may result in

minor or moderate injury’’ or in property

damage incidents.

HIGH PRESSURE WASHER OPERATOR MANUAL

Specifications

Operating pressure 1550 PSI

Water volume 1.2 GPM

Amp draw 13 AMPS

Voltage 120 V

Part No. 1.671-343.0

Serial no.

Kärcher Customer Support USA

Safety Alert Symbols

English 3

1 On/OFF switch

2 High pressure outlet

3 Detergent suction tube with filter

4 Dirtblaster® (Rotating spray wand)

5 Vario Power Spray wand

6 Trigger gun

7 Trigger gun safety lock

8 High pressure hose

9 Water inlet with garden hose

connector

10 Power cord with Ground Fault Circuit

Interrupter (GFCI)

11 Trigger Gun Holder

12 Spray Wand Storage

13 Handle

14 Collapsable transport handle

15 Hose/Cord Caddy

CAUTION

This unit has been designed for use with

cleaning detergents recommended by

the manufacturer. The use of other

cleaning detergents may affect the op-

eration of the machine and void the war-

ranty.

For household use only!

MODEL OVERVIEW

4 English

WARNING

When using this product basic precau-

tions should always be followed, includ-

ing the following:

Read all the instructions before us-

ing the product.

To reduce the risk of injury, close su-

pervision is necessary when a prod-

uct is used near children.

Know how to stop the product and

bleed pressures quickly. Be thor-

oughly familiar with the controls.

Stay alert – watch what you are do-

ing.

Do not operate the product when fa-

tigued or under the influence of alco-

hol or drugs.

Keep operating area clear of all per-

sons.

Do not overreach or stand on unsta-

ble support. Keep good footing and

balance at all times.

Follow the maintenance instructions

specified in the manual.

This Product Is Provided With A

Ground Fault Circuit Interrupter Built

Into The Power Cord Plug. If Re-

placement Of The Plug Or Cord Is

Needed, Use Only Identical Re-

placement Parts.

Risk of Injection or Injury – Do Not

Direct Discharge Stream At Per-

sons.

High pressure jets can be dangerous

if misused. The jet must not be di-

rected at persons, animals, electrical

devices, or the machine itself.

Wear safety goggles.

Do not use acids and solvents in this

product. These products can cause

physical injuries to the operator and

irreversible damage to the machine.

To reduce the risk of electrocution,

keep all connections dry and off the

ground. Do not touch plug with wet

hands.

The Trigger Gun Safety Lock PRE-

VENTS the trigger from accidentally

being engaged. This safety feature

DOES NOT lock trigger in the ON

position.

Do not use extension cord with this

unit.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

English 5

This product is supplied with a Ground

Fault Circuit Interrupter (GFCI) built into

the power cord plug. This device pro-

vides additional protection from the risk

of electric shock. If power is interrupted

in the line, the GFCI will automatically

re-close the circuit to the load after pow-

er is restored. Depending on the GFCI

model, it may be necessary to manually

operate the reset button to restore pow-

er to the GFCI load circuit. If replace-

ment of the plug or cord is needed use

identical replacement parts.

In a double-insulated product, two sys-

tems of insulation are provided instead

of grounding. No grounding means is

provided on a double-insulated product,

nor should a means for grounding be

added to the product. Servicing a dou-

ble-insulated product requires extreme

care and knowledge of the system, and

should be done only by qualified service

personnel. Replacement parts for a

double-insulated product must be iden-

tical to the parts they replace. A double-

insulated product is marked with the

words “double-insulation” or “double-in-

sulated”. The symbol “” may also be

marked on the product.

CAUTION

When connecting the water inlet to the

water supply mains, local regulations of

your water company must be observed.

In some areas the unit must not be con-

nected directly to the public drinking wa-

ter supply. This is to ensure that there is

no feedback of chemicals into the water

supply. Direct connection via a receiver

tank or backflow preventer, for example,

is permitted.

Dirt in the feed water will damage the

unit. To avoid this risk, we recommend

fitting a water filter.

Garden hose must be at least 5/8

inch in diameter.

Flow rate of water supply must not

fall below 2 GPM (gallons per

minute).

Flow rate can be determined by run-

ning the water for one minute into an

empty 5-gallon container.

The water supply temperature must

not exceed 104°F/40°C.

Never use the pressure washer to

draw in water contaminated with sol-

vents, e.g. paint thinners, gasoline,

oil, etc.

Always prevent debris from being

drawn into the unit by using a clean

water source.

GROUND FAULT CIRCUIT

INTERRUPTER PROTECTION

SERVICING OF A DOUBLE-

INSULATED PRODUCT

WATER SUPPLY

(Cold Water Only)

6 English

ÎSTEP 1:

ÎSTEP 2:

ÎSTEP 3:

Attach the high pressure hose to the

trigger gun. Pull out the locking slide

from the right side of the trigger gun

handle (A), and insert the small end

of the high pressure hose into place

(B). Push the locking slide back into

the trigger gun (C) to lock the hose in

position.

ASSEMBLY INSTRUCTIONS

English 7

ÎSTEP 1:

Connect the high pressure hose to

the unit’s high pressure outlet.

ÎSTEP 2:

Insert the spray wand of your choice

into the trigger gun. Press in against

the spring tension and twist into

locked position.

ÎSTEP 3:

Connect garden hose to unit’s water

inlet.

ÎSTEP 4:

Connect garden hose to the cold wa-

ter source and turn water on com-

pletely. Plug the power cord into the

power outlet.

ÎSTEP 5:

Unlock the Safety lock. Trigger the

gun to eliminate trapped air, wait for

a steady flow of water to emerge

from the spray nozzle.

ÎSTEP 6:

Turn on the high pressure washer (I).

The motor starts only if the trigger

of the gun is pulled and shuts off

when the trigger is released.

OPERATING INSTRUCTIONS

8 English

ÎSTEP 1: Plug the Ground Fault Cir-

cuit Interrupter (GFCI) into a working

outlet.

ÎSTEP 2: Press ’’TEST’’, then press

’’RESET’’ to assure proper connec-

tion to power.

Note: The actual appearance of the

GFCI may be different from this illus-

tration.

WARNING

To avoid serious injury never point

spray nozzle at yourself, other per-

sons or animals.

The Vario Power Spray Wand allows

you to adjust the cleaning pressure.

To clean at maximum pressure, the

wand must be positioned to the high

pressure setting (Max).

For lower pressure turn the wand

collar in the minus (Min) direction.

To apply detergent, the wand must

be positioned to the lower pressure

setting (Min).

This nozzle features a 0º pencil jet

which rotates 360º for maximum dirt

cutting action, effectively increasing

cleaning performance up to 50%.

This nozzle combines the cleaning

performance of a 0º pencil jet with

the surface coverage of a wide angle

nozzle.

Not recommended for soft materi-

als, siding, painted surfaces,

decks or autos.

Always test an inconspicuous area

before cleaning with the Dirtblaster

GFCI INSTRUCTIONS

USING THE ACCESSORIES

Vario Power Spray Wand

Dirtblaster®

English 9

Detergents can only be applied at

low pressure (Min.).

ÎSTEP 1:

Install the Vario Power Spray Wand.

Set the spray wand to the low pres-

sure setting (Min.).

ÎSTEP 2:

Fill a container with Kärcher deter-

gent. Place the filter end of detergent

suction tube into the container.

ÎSTEP 3:

Turn on the pressure washer (I).

Pull trigger to operate unit:

Liquid detergent is drawn into the

unit and mixed with water. Apply de-

tergent to work area. Do not allow

detergent to dry on surface.

ÎSTEP 4:

Always draw fresh water through

the detergent suction tube when

done, to rinse/flush any remaining

detergents from the injection sys-

tem.

For best results see Cleaning Tips

for specific information on how to

clean different surfaces.

Always Use Kärcher Detergent for

Best Results

Kärcher biodegradable detergents are

specially formulated to protect the envi-

ronment and your pressure washer. The

special formula won’t clog the suction

tube filter and will protect the internal

parts of the pressure washer for a long-

er life. For Kärcher Detergents, check

your retailer or visit our website:

www.karcher-usa.com/home

The following Kärcher detergents are

available:

One Gallon ready to use

All Purpose & Vehicle Cleaner

Deck & Patio Cleaner

Heavy Duty Degreaser

Exterior House Cleaner

CAUTION

Never use:

– Bleach, Chlorine products and other

corrosive chemicals

– Liquids containing solvents (i.e.,

paint thinners, gasoline, oils)

– Tri-sodium phosphate products

– Ammonia products

– Acid-based products

These chemicals will harm the unit and

will damage the surface being cleaned.

WORKING WITH DETERGENTS

10 English

ÎSTEP 1:

Release trigger and engage gun

safety lock.

ÎSTEP 2:

Turn pressure washer to OFF (O)

position.

ÎSTEP 1:

Turn the switch to OFF (0) position

and unplug cord from outlet.

ÎSTEP 2:

Turn off the water source.

ÎSTEP 3:

Press trigger to release water pres-

sure.

ÎSTEP 4:

Disconnect the garden hose from

the water inlet on the unit.

ÎSTEP 5:

Disconnect the high pressure hose

from the high pressure outlet.

ÎSTEP 6:

Release trigger and engage gun

safety lock.

TAKING A BREAK ..five minutes or more

SHUTTING DOWN & CLEAN UP

English 11

Î1: Disconnect all water connections.

Î2: Turn on the machine for a few

seconds, until the water which had

remained in the pump exits, turn off

immediately.

Î3: Do not allow high pressure hose

to become kinked.

Î4: Store the machine and accesso-

ries in a room which does not reach

freezing temperatures. DO NOT

store near furnace or other sources

of heat as it may dry out the pump

seals.

CAUTION

Failure to follow the above directions

will result in damage to the pump as-

sembly and accessories.

Kärcher also recommends the regular

practice of using a pump protector like

“Kärcher Pump Guard’’ to help during

storage in the winter months.

Pull out the water inlet filter with flat-

nose pliers and rinse out in warm water.

Note: if you pull out the water inlet filter

the washer gets out too. Take care to

mount it again after cleaning the filter.

Pull it out and rinse out in warm water.

The unit is maintenance-free.

WINTERIZING AND LONG-TERM STORAGE

CARE AND MAINTENANCE INSTRUCTIONS

Cleaning the water inlet filter Cleaning the detergent inlet filter

Maintenance

12 English

(with or without detergent). Pre-rinse

deck and surrounding area with fresh

water. If using Kärcher Deck Wash, ap-

ply to surface at low pressure. For best

results, limit your work area to smaller

sections of approximately 25 square

feet. Allow Deck Wash to remain on sur-

face 1-3 minutes. Do not allow deter-

gent to dry on surface. Rinse at high

pressure in a long sweeping motion

keeping the spray nozzle approximately

3-6 inches from the cleaning surface.

Always clean from top to bottom and

from left to right. When moving on to a

new section of the cleaning surface, be

sure to overlap the previous section to

eliminate stop marks and ensure a more

even cleaning result.

(with or without detergent). Pre-rinse

cleaning surface with fresh water. If us-

ing Kärcher Pressure Wash, apply to

surface at low pressure (for best results,

limit your work area to sections of ap-

proximately 6 feet and always apply de-

tergent from bottom to top). Allow

Pressure Wash to remain on surface 1-

3 minutes. Do not allow detergent to dry

on surface, if surface appears to be dry-

ing, simply wet down surface with fresh

water. If needed, use special wash

brush attachment (not included) to re-

move stubborn dirt. Rinse at high pres-

sure from top to bottom in an even

sweeping motion keeping the spray

nozzle approximately 6 inches from the

cleaning surface.

(with or without detergent). Pre-rinse

cleaning surface with fresh water. If us-

ing Kärcher Pressure Wash or Degreas-

er, apply to surface at low pressure. For

best results, limit your work area to

smaller sections of approximately 25

square feet. Allow Pressure Wash or

Degreaser to remain on surface 1-3

minutes. Do not allow detergent to dry

on surface. Rinse at high pressure in a

sweeping motion keeping the spray

nozzle approximately 3-6 inches from

the cleaning surface. Always clean from

top to bottom and from left to right. For

removing extremely stubborn stains,

use the Dirtblaster Nozzle.

(with or without detergent). Pre-rinse

vehicle with fresh water. If using Kärch-

er Touchless Vehicle Wash, apply to

surface at low pressure. For best re-

sults, clean one side of vehicle at a time

and always apply detergent from bottom

to top, do not allow detergent to dry on

surface. If needed, use special wash

brush attachment (not included) to re-

move stubborn dirt. Rinse at high pres-

sure in a sweeping motion keeping the

spray nozzle approximately 6-8 inches

from the cleaning surface (distance

should increase when rinsing pin-strip-

ing or other sensitive surfaces). Always

clean from top to bottom and from left to

right. For best results, wipe surface dry

with a chamois or soft dry cloth.

CLEANING TIPS

Deck Cleaning

House Siding

Cement Patios, Brick and Stone

Cars, Boats & Motorcycles

English 13

(with or without detergent). Pre-rinse

cleaning surface with fresh water. If us-

ing Kärcher Pressure Wash or Degreas-

er, apply detergent at low pressure.

Allow Pressure Wash to remain on sur-

face 1-3 minutes.Do not allow detergent

to dry on surface. Rinse at high pres-

sure keeping the spray nozzle approxi-

mately 3-6 inches from the cleaning

surface. For removing extremely stub-

born dirt, it may be necessary to move

the spray nozzle even closer to the sur-

face for greater dirt cutting action.

(with or without detergent). Pre-rinse

furniture and surrounding area with

fresh water. If using Pressure Wash, ap-

ply to surface at low pressure. Allow

Pressure Wash to remain on surface 1-

3 minutes. Do not allow detergent to dry

on surface. If needed use special Wash

Brush Attachment (not included) to re-

move stubborn dirt. Rinse at high pres-

sure in a sweeping motion keeping the

spray nozzle approximately 3-6 inches

from the cleaning surface. For best re-

sults, clean from top to bottom and from

left to right.

Before cleaning any surface an in-

conspicuous area should be cleaned

to test spray pattern and distance for

maximum cleaning results.

If painted surfaces are peeling or

chipping, use extreme caution as

pressure washer may remove the

loose paint from the surface.

When using on surfaces which might

come in contact with food, flush sur-

faces with plenty of drinking water.

For additional cleaning tips, visit our

website at www.karcher-usa.com/

home

Barbecue Grills, Outdoor Power

Equipment & Gardening Tools

Patio & Lawn Furniture

Recommendations

14 English

CAUTION

Disconnect the machine from the power

source before making any repair.

TROUBLESHOOTING

Symptom Cause Solution

Motor will not start On/Off switch is in the “OFF”

(O) position.

Turn switch to the “ON” (I)

position

Power cord is not plugged in. Plug in power cord.

Electrical outlet does not

supply adequate power.

Try a different outlet.

Tripped circuit breaker. Switch off pressure washer.

GFCI will reset once the

temperature of the unit drops.

Unit does not reach

high pressure.

Diameter of garden hose is

too small.

Replace with a 5/8 inch or

larger garden hose.

Water supply is restricted. Check garden hose for kinks,

leaks and blockage.

Not enough inlet water

supply.

Open water source full force.

Water inlet filter is clogged. Remove filter and rinse out in

warm water.

Spray wand is on low

pressure position.

Turn spray wand to high

pressure position.

Output pressure

varies high and low.

Not enough inlet water

supply.

Turn water on full force.

Check garden hose for kinks,

leaks or blockage.

Pump is sucking air. Check that hoses and fittings

are air tight. Turn off machine

and purge pump by

squeezing trigger gun until a

steady flow of water emerges

through the nozzle.

Water inlet filter is clogged. Remove filter and rinse out in

warm water.

Discharge nozzle is

obstructed.

Blow out or remove debris

with a fine needle.

Calcified gun, hose or spray

wand.

Run distilled vinegar through

detergent suction tube.

English 15

If you encounter any additional difficul-

ties not listed, please call

1-800-537-4129 for help or visit our

website: www.karcher-usa.com/home

No detergent. Detergent suction tube not

properly connected to the

machine.

Check connection.

Detergent is too thick. Dilute detergent, for best

results use Kärcher

detergent.

Filter on detergent suction

tube is clogged.

Run warm water through filter

to remove debris.

Damaged or clogged

detergent suction tube.

Remove obstruction or

replace detergent suction

tube.

Spray wand is in high

pressure position.

Turn spray wand tip to low

pressure position.

Discharge nozzle is

obstructed.

Blow out or remove debris

with fine needle.

Garden hose

connection leaks.

Loose fittings. Tighten fittings.

Missing/worn rubber washer. Insert new washer.

Spray wand leaks. Spray wand not properly

attached.

Insert the spray wand into the

trigger gun. Carefully press in

against the spring tension

and twist into the lokked

position.

Broken o-ring or plastic insert.

Call Customer Support

Pump is noisy. Pump is sucking air. Check that hoses and fittings

are air tight. Turn off machine

and purge pump by

squeezing trigger gun until a

steady flow of water emerges

through the nozzle.

Water leaks from

pump (up to 10

drops per minute is

permissible).

Loose fittings. Check that all fittings are

tight.

Water seals are damaged or

worn.

Call Customer Support

Oil Drip. Oil seals are damaged or

worn.

Call Customer Support

Symptom Cause Solution

Kärcher Customer Support USA

16 Español

Vista General del Modelo 17

Instrucciones de Seguridad

Importantes 18

Instrucciones de Montaje 20

Instrucciones de Funcionamiento 21

Instrucciones del Interruptor de Circuito

de Avería por Puesta a Tierra 22

Utilización de los Accesorios 22

Trabajar con Detergentes 23

Apagado y Limpieza 24

Protección contra los Agentes

Invernales y Almacenamiento

Prolongado 25

Instrucciones de Conservación y

Mantenimiento 25

Consejos de Limpieza 26

Localicación y reparación de averías28

Llame al: 1-800-537-4129 si necesita

ayuda o visite nuestra página Web:

www.karcher-usa.com/home

PELIGRO

indica “una situación de peligro inmi-

nente que, si no se evita, puede causar

lesiones graves e incluso la muerte”.

ADVERTENCIA

indica “una situación de peligro poten-

cial que, si no se evita, puede causar le-

siones e incluso la muerte”.

ATENCIÓN

indica “una situación de peligro poten-

cial que, si no se evita, puede causar le-

siones de poca importancia o leves", o

daños materiales.

MANUAL DE USUARIO DEL LIMPIADOR DE ALTA PRESIÓN

Especificaciones

Presión de trabajo 1550 PSI

Volumen de agua 1.2 GPM

Amperaje 13 AMPS

Voltaje 120 V

Nº de pieza 1.671-343.0

Nº de serie

Servicio de asistencia al cliente

de Kärcher de EE.UU.

Símbolos de aviso de seguridad

Español 17

1 Interruptor de encendido/apagado

2 Salida de alta presión

3 Tubo de succión de detergente con

filtro

4 Dirtblaster® (pulverizador telescópi-

co rotatorio)

5 Pulverizador telescópico variable

6 Pistola de disparo

7 Pestillo de seguridad de la pistola de

disparo

8 Manguera de alta presión

9 Toma de agua con conector para

manguera de jardín

10 Cable de potencia con interruptor de

circuito de avería por puesta a tierra

11 Zona de recogida, pistola

12 Zona de recogida, pulverizador

13 Asa de transporte

14 Carro de transporte

15 Soporte para manguera/cable

ATENCIÓN

Siga las instrucciones de mantenimien-

to especificadas en el manual

Este aparato ha sido diseñado para ser

utilizado con detergentes de limpieza

del fabricante. El uso de otros detergen-

tes de limpieza puede afectar al funcio-

namiento del aparato y hacer que deje

de tener validez la garantía.

Sólo para uso doméstico.

Vista General del Modelo

18 Español

ATENCIÓN

Al utilizar este producto, tome siempre

las precauciones básicas, incluidas las

siguientes:

!Lea todas las instrucciones antes de

utilizar el producto.

!Para reducir el riesgo de lesiones,

es necesario extremar las precau-

ciones cuando se utilice el aparato

cerca de niños.

!Tiene que saber cómo parar el apa-

rato y purgar la presión rápidamen-

te. Familiarícese con los controles.

!Esté alerta; mire lo que esté hacien-

do.

!No haga funcionar el producto si

está cansado o si está bajo los efec-

tos del alcohol o las drogas.

!Mantenga la zona en la que esté lim-

piando libre de personas.

!No se alargue demasiado sobre una

base ni se ponga sobre una base

inestable. Mantenga en todo mo-

mento una buena base de apoyo y

un buen equilibrio.

!Siga las instrucciones de manteni-

miento especificadas en el manual.

!Este producto se suministra con un

interruptor de circuito de avería por

puesta a tierra, que está montado

en el enchufe del cable de potencia.

Si es necesario reemplazar el en-

chufe o el cable, utilice sólo piezas

de repuesto idénticas.

!Riesgo de inyección o lesiones a

personas; no dé con el chorro direc-

tamente a personas.

!Los chorros de alta presión pueden

ser peligrosos si se utilizan mal. El

chorro no debe ser enfocado a per-

sonas, animales, aparatos eléctricos

ni al aparato mismo.

!Póngase gafas protectoras.

!No utilice ácidos ni disolventes con

este producto.. Estos productos

pueden causar lesiones físicas al

usuario y daños irreversibles al apa-

rato.

!Para reducir el riesgo de electrocu-

ción, mantenga todas las conexio-

nes secas y alejadas del suelo. No

toque el enchufe con las manos mo-

jadas.

!El pestillo de seguridad de la pistola

de disparo EVITA que la pistola se

dispare accidentalmente. Esta ca-

racterística de seguridad NO blo-

quea el disparo en la posición de

encendido.

!No se debe usar el cable de exten-

sión para esta máquina.

GUARDE ESTAS INSTRUCCIONES

Instrucciones de Seguridad Importantes

Español 19

Este producto se suministra con un inte-

rruptor de circuito de avería por puesta

a tierra montado en el enchufe del cable

de potencia. Este aparato proporciona

una protección adicional contra el ries-

go de electrochoque. Si la corriente se

interrumpe en la línea, el interruptor de

circuito de avería por puesta a tierra vol-

verá a cerrar, automáticamente, el cir-

cuito a la carga una vez restablecida la

corriente. En función del modelo de in-

terruptor, puede que sea necesario te-

ner que poner en funcionamiento el

aparato manualmente mediante el bo-

tón de reinicio para restaurar la corrien-

te del circuito de carga del interruptor de

circuito de avería por puesta a tierra. Si

es necesario reemplazar el enchufe o el

cable, utilice piezas idénticas.

Los artefactos con doble aislamiento

tienen dos sistemas de aislamiento en

vez de conexión a tierra. Esto significa

que no trae medios de conexión a tierra

y que tampoco se le debe agregar uno.

El mantenimiento de estos artefactos

exige mucho cuidado y conocimiento

del sistema y sólo debe hacerlo perso-

nal calificado de servicio. Las piezas de

repuesto deben ser idénticas a las origi-

nales.Los artefactos con doble aisla-

miento están marcados "DOUBLE

INSULATION" o "DOUBLE INSULA-

TED". También podría tener el símbolo

ATENCIÓN

Al conectar la toma de agua a la red de

suministro del agua, es obligatorio res-

petar la normativa local establecida por

la compañía del agua. En algunas zo-

nas, está prohibido conectar la unidad

directamente a la red pública de sumi-

nistro de agua potable. Esto es así para

garantizar que no penetren sustancias

químicas en la red de suministro del

agua. Sí se permite efectuar la co-

nexión directamente por ejemplo a tra-

vés de un depósito receptor o un

dispositivo antirretorno.

Si el agua de alimentación está sucia, la

unidad sufrirá daños. Para evitar este

riesgo, le recomendamos que monte un

filtro de agua.

!La manguera de agua tiene que te-

ner al menos 5/8 pulgadas de diá-

metro.

!El caudal de agua no debe ser infe-

rior a 2 GPM (galones por minuto).

!El caudal de agua se puede determi-

nar llenando de agua un recipiente

vacío de 5 galones durante un minu-

to.

!La temperatura de la toma de agua

no de be sobrepasar los 104°F/

40°C.

!No utilice nunca el limpiador a pre-

sión para aspirar agua contaminada

con disolventes como, p. ej., dilu-

yentes de pintura, gasolina, aceite,

etc.

!Evite siempre que la unidad aspire

residuos utilizando una fuente de

abastecimiento cuya agua esté lim-

pia.

Protección mediante interruptor

de circuito de avería por puesta a

tierra

MANTENIMIENTO A UN ARTE-

FACTO QUE TIENE

DOBLE AISLAMIENTO

SUMINISTRO DE AGUA

(sólo agua fría)

20 Español

"PASO 1:

"PASO 2:

"PASO 3:

Monte la manguera de alta presión

en la pistola de disparo. Desengan-

che la lengüeta corrediza de fijación

del lateral derecho del asa de la pi-

stola (A) e inserte el extremo pe-

queño de la manguera de alta

presión en su sitio (B). Vuelva a me-

ter la lengüeta corrediza de fijación

en la pistola de disparo (C) para fijar

la manguera en esa posición.

Instrucciones de Montaje

La page charge ...

Kärcher K 2.110 M Manuel utilisateur

Marque: Kärcher

Modèle: K 2.110 M

Catégorie: Outils de jardin

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Kärcher K 2.110 M User manual
español: Kärcher K 2.110 M Manual de usuario

Kärcher K 2.110 M Manuel utilisateur

Kärcher K 2.110 M Manuel utilisateur

dans d''autres langues

Documents connexes