Makita C011 Mode d'emploi

Makita
Marque
Makita
Modèle
C011
Catégorie
Testeurs de réseau câblé
Taper
Mode d'emploi
Order Number
: GETEC-C1-20-647
FCC Part 15 subpart C
Test Report Number
: GETEC-E3-20-087
Page 1 / 1
EUT Type: RF Remote Control Unit
FCC ID.: OZ5TC011MA
APPENDIX H
: USER’S MANUAL
[KOREA]
C011 User Information
(Model Name : C011)
Table of Contents
1. Overview and Specification of C011
(1) Overview
(2) Specification
2. Precautions
3. Customer Support
(1) Overview
This remote control uses wireless communication in the 2.4GHz band,
It is a product that can be controlled with the MAKITA Module
receiver and key button.
(2) Specifications
구 분 내 용
Model No. C011
Range of frequency
2402~2480 MHz
Channel 40 Channel
Output power 3 dBm
Receive sensitivity –92 dBm
Size Width 58mm X Thickness 15.9 mm X Length
131.5 mm
(tolerance± 0.8 mm)
Weight 63.2g (tolerance± 5g, battery not applied)
Power source AAA x 2EA, (2 alkaline batteries are used)
Operational
Temperature range
-20 ℃ ~ + 50 ℃
Importer 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-
8502 Japan
1. Overview and Specification of C011
2. Precaution
(1) After replacement of the battery, use the remote control following pairing in accordance with user
manual.
(2) If the unit does not operate after replacement of battery, reattempt pairing in accordance with the
user manual.
(3) If the remote controller is not being used for prolonged period of time, it is recommended you
remove the battery from the unit.
(4) Do not dismantle or exert heat to the battery.
(5) Do not drop battery or exert extreme impact that may even cause the case to be damaged.
(6) Do not immerse the battery in water.
(7) There is danger of explosion if a the battery is inserted reversely.
(8)
Properly dispose of used batteries.
3. Customer Support
Refer to the contact number for services provided in the MAKITA Manual.
[KC certification mark and number]
Certification number : R-C-OHS-C011
[TELEC certification mark and number]
Certification number :XXXXXX
[FCC ID certification mark and number]
Certification number :OZ5TC011MA
[IC certification mark and number]
Certification number :21703-C011
[CE certification mark]
“Since the wireless device has the potential for radio wave interference, services related to personal
safety cannot be provided.”
Business name : Ohsung Electronics Co., Ltd
Manufacturing date : 2020.12
Manufacturer/Country of Manufacture : Ohsung Electronics Co., Ltd / Korea
Equipment/Model name : Specific low power wireless device (wireless device for wireless data
communication system / C011
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1.This device may not cause harmful interference
2.This device must accept any interference received, including interference that may cause
undesired operation. Any changes or modifications not expressly approved by the party
responsible for compliance could void the authority to operate equipment. The antenna(s)
used for this transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Federal Communication Commissions (FCC) Radiation Exposure
Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.
Canadian (IC)
Two-part Statement (English and French)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject
to the following two conditions: (1) This device may not cause interference. (2) This device
must accept any interference, including interference that may cause undesired operation of
the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Makita C011 Mode d'emploi

Makita
Marque
Makita
Modèle
C011
Catégorie
Testeurs de réseau câblé
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Autres documents