Dewertokin Technology Group RF42 Mode d'emploi

Taper
Mode d'emploi
Instructions of RF42
1 appearance
2 Key function
Key value
Specification
CHILD LOCK Press and hold button till the backlight flashes remote
enters locking or unlocking mode
PAIR press and hold button ,the remote enters pairing mode
M Click button, the bed moves to M position, press and
hold M button for 5s, until backlight flashes, the control set the
current position as M position
FLASH LIGHT Click button, open or close flash light
HEAD UP Press and hold button, head actuator moves out, stop
when released
HEAD DOWN Press and hold button, head actuator moves in, stop
when released
FOOT UP Press and hold button, foot actuator moves out, stop
when released
FOOTDOWN Press and hold button,foot actuator moves in, stop when
released
ZG Click button, the bed moves to zeroG position, press and
hold zeroG button for 5s, until backlight flashes, the control set
the current position as zeroG position
FLAT Press and hold button, the bed goes flat
TV Click button, the bed moves to TV position, press and
hold TV button for 5s, until backlight flashes, the control set the
current position as TV position
ANTI SNORE Click button, the bed moves to antisnore position, press
and hold antisnore button for 5s until backlight flashes, the
control set the current position as antisnore position
Lounge Click button, the bed moves to Lounge position, press
and hold Lounge button for 5s, until backlight flashes, the
control set the current position as Lounge position
MASSAGE HEAD Click button to switch massage intensity of head
massage motors
TIMER Click button to switch massage time
MASSAGE FOOT Click button to switch massage intensity of foot
massage motors
MASSAGE ON/OFF Click button to turn on/off head & foot massage motors
UNDER BED LIGHT Click light button to turn on/off the under bed light
MASSAGE TYPE Click button to switch massage mode
LED 1 10 MIN Massage time: 10 minutes
LED 2 20 MIN Massage time: 20 minutes
LED 3 30 MIN Massage time: 30 minutes
Other function 1: Zero G + Flat
Press and hold zeroG and flat button for 5s until
backlight
flashes, the memory positions of control box reset
to default settings
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirment. The device can be used in
portable exposure condition without restriction.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt
RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. The device has been evaluated to meet general RF exposure requirement.
Le matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés pour fac un
autre environnement. ce dispositif a été évalué à satisfaire l'exigence générale de l'exposition aux rf.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Dewertokin Technology Group RF42 Mode d'emploi

Taper
Mode d'emploi