Pentair INTELLIBRITE 5G Guide d'installation

Catégorie
Accessoires de piscine hors terre
Taper
Guide d'installation
INTELLIBRITE® 5G White Pool and Spa LED Light Installation and User’s Guide
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
INSTALLATION AND
USER’S GUIDE
INTELLIBRITE® 5G
WHITE AND COLOR POOL AND SPA LIGHTS
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
Technical Support: Phone: (800) 831-7133 - Fax: (800) 284-4151
Web sites: www.pentairpool.com and www.staritepool.com:
Contents
IMPORTANT WARNING AND SAFETY INSTRUCTIONS...................................ii
IntelliBrite 5G Pool and Spa Lights Overview ....................................................1
Operating IntelliBrite Pool and Spa lights using a wall switch (12 VAC) ............ 1
Using an External Transformer for Multiple IntelliBrite 12 VAC Light ............. .....1
Powering on IntelliBrite 5G Lights .................................................................... 2
Selecting a light show mode or xed color ........................................................ 2
Replacing the IntelliBrite 5G Pool and Spa Light Assembly
(in an existing pool/after Electrical Requirements are met) ............................ 3/4
Installing the IntelliBrite 5G Pool and Spa Light Fixture
(new pool construction/ /after Electrical Requirements are met) ) .................. 6/7
IntelliBrite 5G Pool Light (12 V) Fuse Harness Replacement .......................... 9
Replacing the IntelliBrite 5G Pool Light Circuit Board Assembly
(in an existing pool) .......................................................................................... 9
Wide and Narrow Angle Lens Adjustment........................................................17
IntelliBrite 5G Pool Light Replacement Kit Part Numbers ................................18
Replacing the IntelliBrite Spa Light Face ring and Gasket
(P/N 640045) or Gasket and Lens (640046) ................................................... 19
IntelliBrite 5G Spa Light Replacement Kit Part Numbers ................................ 23
IntelliBrite Color Light Controller ..................................................................... 24
Always install a new lens gasket (see part number in this
User’s Guide on page 9 and 19), when ever reassembling
the light. Failure to do so may permit water to leak into the assembly which
could cause; (a) an electrical hazard resulting in death or serious injury to pool
users, installer, or others due to electrical shock, or (b) breakage of the lamp
or lens, which likewise could result in serious injury to pool user, installers, or
bystanders, or in damage to property.
Before Installing luminaries read the following:
THE INTELLIBRITE 5G LED POOL LIGHT AND
SPA LIGHT CANNOT BE USED ON A DIMMER CIRCUIT. USING
A DIMMER SWITCH WILL RESULT IN PERMANENT DAMAGE TO
THE LIGHT.
P/N 619921 Rev K - 4/2015
FOR 12 VAC LUMINARIES: ALWAYS USE A SEPARATE STEP DOWN
TRANSFORMER TO POWER LUMINARIES. SEE DIAGRAM ON PAGE 7.
Note: Connect all three wires to the corresponding circuit wires in the
Junction Box (black wire to power, white wire to common, and green
wire to ground).
12 VAC LUMINARIES SPECIFICATION: 12 VAC, 50/60 Hz REPLACE ANY CRACKED
PROTECTIVE SHIELD (CRACKED LENS) WITH NEW LENS AND GASKET.
i
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
ii
Most states and local codes regulate the construction, installation,
and operation of public pools and spas, and the construction of
residential pools and spas. It is important to comply with these codes, many of which
directly regulate the installation and use of this product. Consult your local building and
health codes for more information.
SERIOUS BODILY INJURY OR DEATH CAN RESULT IF THIS LIGHT
IS NOT INSTALLED AND USED CORRECTLY.
INSTALLERS, POOL OPERATORS AND POOL OWNERS MUST
READ THESE WARNINGS AND ALL INSTRUCTIONS BEFORE
USING THE POOL AND/OR SPA LIGHT.
Before installing this product, read and follow all warning notices
and instructions in this Guide. Failure to follow warnings and
instructions can result in severe injury, death, or property damage.
Call (800) 831-7133 for additional free copies of these instructions. Please refer to www.
pentairpool.com for more information related to this products.
IMPORTANT NOTICE - Attention Installer: This Installation and User’s
Guide (“Guide”) contains important information about the installation, operation
and safe use of this underwater pool and spa light. This Guide should be given
to the owner and/or operator of this equipment.
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
BEFORE WORKING ON POOL AND SPA LIGHTS always disconnect power
to the pool and/or spa lights at the circuit breaker from the light
before servicing the light. Failure to do so could result in death
or serious injury to service person, pool users or others due to
electric shock.
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION:
This underwater light must be installed by a licensed or certified electrician or a
qualified pool professional in accordance with the current National Electrical Code
(NEC), NFPA 70 or the Canadian Electrical Code (CEC), CSA C22.1. All applicable
local installation codes and ordinances must also be adhered to. Improper installation
will create an electrical hazard which could result in death or serious injury to pool
users, installers or others due to electrical shock, and may also cause damage
to property. Always disconnect the power to the pool light at the circuit breaker
before servicing the light. Failure to do so could result in death or serious injury to
serviceman, pool users or others due to electrical shock.
Important Safety Information for Pentair Water Pool and Spa Niche
and Light Installation
• AllNicheandLightinstallationsmustconformwithallcodes.Iflocalcodes
mandate a cord seal, use Pentair Water Pool and Spa plastic niches
(P/N 79206600 and P/N 79206700) and Cord Seal Kit (P/N 670044).
• Underno circumstances replace lights by splicing wire under water or behind
niche.
THE INTELLIBRITE® POOL AND SPA LIGHT REqUIRE HIGH vOLTAGE WHICH
CAN SHOCK, BURN, OR CAUSE DEATH.
Before Installing luminaries read the following:
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL.
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
For countries in compliance with International Electromechnical
Commission (IEC) regulatory standards: The light fixture must
be installed by a licensed or certified electrician or a qualified pool service person, in
accordance with IEC 364-7-702 and all applicable local codes and ordinance. Improper
installation will create an electrical hazard, which could result in death or serious injury
to pool user, installer or other due to electrical shock and may also cause damage to the
property.
iii
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
RISK OF ELECTRIC SHOCK AND INJURY. USE ONLY THE
(*) Note: Wet-niche luminaires complying with requirements for both uses may bare
both the Listed Wet-Niche Submersible Luminaires UL Mark. A luminaire not bearing the
corresponding UL Listing Mark is not considered by UL to have been produced under ULs
Listing and Follow-Up Service for the associated usage location.
CAUTION - The IntelliBrite® 5G Light fixture must only be used with Pentair Water Pool
and Spa fixture housings (niches). If the IntelliBrite light fixture is installed into other
niches, the installation will not carry U.L. approval and will void all warranties.
Salt is an inherently corrosive material. While the levels of salt required
for proper operation of an electronic chlorine generator are relatively low
when compared to sea water and other salt solutions, placing any amount of salt in your
pool increases the likelihood of corrosion or other deterioration of pool equipment and any
surfaces used in and around your pool. Metal parts and certain natural and man-made
surfaces are particularly susceptible to corrosion and deterioration when used in and
around salt water pools. Pentair does not represent or otherwise guarantee that the proper
use of an electronic chlorine generator will prevent corrosion or other deterioration of pool
equipment and any surfaces used in and around your pool. Consult your experienced
pool professional, who should be able to advise you on the proper material selection,
installation techniques for those materials, and the proper use, care and maintenance of
those materials for your specific pool type and location in order to minimize the corrosion
and deterioration that is inherent in and around salt water pools.
INSTALLATION METHOD SPECIFIED BELOW.
NOTICE: The external flexible cable or cord of this luminaire cannot be replaced; if
the cord is damaged, the luminaire shall be destroyed.
- REPLACE ANY CRACKED PROTECTIVE SHIELD (CRACKED LENS) WITH NEW
LENS AND GASKET. FOR MORE INFORMATION SEE PAGE 11.
- FOR LIGHT OPERATION, ONLY USE A SAFETY ISOLATION TRANSFORMER.
POOL AND SPA FIXED LUMINARIES: Follow these guidelines when installing,
replacing or repairing Pentair Aquatic Systems Pool and Spa fixed luminaries:
Location of Pentair Water Pool and Spa Fountain Required Installation Method
Luminaire Use Fixture* (P/N 560001 and P/N 560000)
Swimming Pool Wet-Niche Swimming Pool Fixture Housing (Forming Shell) ONLY.
and Spa (or Spa) Luminaire (Light) DO NOT USE Fountain Fixture Stand.
Fountain Wet-Niche Submersible Luminaire (Light) Fixture Housing (Forming Shell) or
swimming Pool (or Spa) Luminair (Light) Fountain Fixture Stand
CAUTION! Luminaires not suitable for direct mounting
on normally flammable surfaces (suitable ONLY for
mounting on non-combustible surfaces.
Surface Mount
Fixed pool and spa luminaries specification:
12 VAC 50/60 Hz - 120VAC ,50/60 Hz.
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
IntelliBrite® 5G Pool and Spa Lights Overview
Operating Pool and Spa Lights Using a Wall Switch (12 VAC)
IntelliBrite 5G pool and spa lights can be manually controlled using a standard wall-mount
light switch. Multiple IntelliBrite lights can be connected via a junction box to a single
switch so that all lights can be switched on and off together. IntelliBrite lights can also be
automatically controlled via Pentair IntelliTouch®, EasyTouch® and SunTouch® Control
Systems. Note: Multiple IntelliBrite 5G pool/spa lights can also be controlled using
the IntelliBrite Controller, for more information see page 2.
Using an External Transformer for Multiple IntelliBrite 12 VAC Lights
When using multiple IntelliBrite 12 VAC lights on a 300 Watt transformer, it is
recommended that no more than three IntelliBrite pool lights and one (1) IntelliBrite Spa
light be used. It is also recommended not to exceed 100 feet of total cable run between
the transformer and light. Note: For long cable lengths, set transformer to 14 VAC
(see diagrams below).
300 Watt
Transformer J Box
12 Gauge
(Minimum)
100 ft.
300 Watt
Transformer J Box
12 Gauge
(minimum)
150 ft. max. for spa light
200 ft. max. for pool light
1
This manual describes how to install the IntelliBrite 5G white and color pool light and the
IntelliBrite 5G white and color spa light.
The IntelliBrite 5G white light provides a brilliant white light for a spectacular effect in
your pool and spa. The IntelliBrite 5G white light lens geometry (pool light only) provides
a choice between two light beam shapes; wider coverage with less intensity, or narrower
coverage with more intensity.
The IntelliBrite 5G color light provides brilliant vivid multi-colors with spectacular effects
for your pool and spa. Choose one of the seven pre-programmed color light shows or
select one of the five fixed colors to create virtually endless range of dramatic underwater
lighting effects for a spectacular effect in your pool and spa.
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
Powering on IntelliBrite® 5G Color Lights
2
When the IntelliBrite light is powered on, a momentarily white light will illuminate,
followed by the previously selected color. Note: If power to the light is off for more
than five (5) seconds, the last color show mode or fixed color that was saved will be
displayed.
Selecting a light show mode or fixed color
Switch power on to the light. A white light will momentarily illuminate, followed by the pre-
viously selected color. To select a color show mode (1-7) or fixed color (8-12), turn the wall
switch off/on a specific number of times. Each number (1-12) shown below corresponds to
the number of times to power-cycle the switch to activate a color light show or fixed color.
For details about saving color effects while in “show” modes, see “Hold” and “Recall” fea-
ture on page 4. Example: To select California Sunset Mode; turn the light on, then turn off
and on six times. During the off/on switching process, no illumination will occur,
Saving a Color Mode or Fixed Color: When power is switched off to the IntelliBrite
color lights, the last color show mode or fixed color will be saved. The next time the light
is powered on, the previously saved color show mode or fixed color will be displayed.
For example, while in “Party Mode” switch the light off. Wait more than 10 seconds,
switch the light back on to resume “Party Mode.
During the off/on switching process, before the selected color is displayed,
no illumination will occur for a brief second. This operating
mode is normal during the switching process. During this period the pool and spa will be
dark and precautions should be taken to avoid unforeseen accidents. Failure to observe
this warning may result in serious injury or death to pool and spa users.
1 SAm Mode: Cycles through
white, magenta, blue and
green colors (emulates
the Pentair SAm® color
changing light).
2 Party Mode: Rapid color
changing building energy
and excitement.
3 Romance Mode: Slow
color transitions creating a
mesmerizing and calming
effect.
4 Caribbean Mode: Transitions
between a variety of blues
and greens.
5 American Mode: Patriotic
red, white and blue
transition.
6 California Sunset Mode:
Dramatic transitions of
orange, red and magenta
tones.
7 Royal Mode: Richer, deeper
color tones.
8 Blue: Fixed color.
9 Green: Fixed color.
10 Red: Fixed color.
11 White: Fixed color.
12 Magenta: Fixed color.
13 Hold: Save the current color
effect during a color light
show.
14 Recall: Activate the last
saved color effect.
Number of times to cycle power (1-5)
Number of times to cycle power (6-14)
Using the IntelliBrite Controller (sold separately, P/N 600054), IntelliBrite 5G color pool/spa
lights can all be synchronized so that individual or multiple IntelliBrite lights all lights can be
switched on and off together.
Using an IntelliBrite Color Light Controller
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
Risk of Electrical Shock or Electrocution!
This underwater light must be installed by a licensed or certified
electrician or a qualified pool professional in accordance with
the National Electrical Code and all applicable local codes and
ordinances. Improper installation will create an electrical hazard
which could result in death or serious injury to pool users,
installers or others due to electrical shock, and may also cause
damage to property. Always disconnect the power to the pool
light at the circuit breaker before servicing the light. Failure to
do so could result in death or serious injury to serviceman, pool
users or others due to electrical shock.
Replacing the IntelliBrite® 5G Pool and Spa
Light Assembly (in an existing pool or spa)
Verify that the pool and spa meets the requirements of the current National Electrical Code
and all local codes and ordinances. A licensed or certified electrician must install the
electrical system to meet or exceed those requirements before the underwater light is
installed. Some of the requirements of the National Electrical Code which the pool’s
electrical system must meet are as follows:
• ThelightingcircuithasaGroundFaultCircuitInterrupter(GFCI)forlinevoltage
models, and has an appropriately rated circuit breaker.
• TheJunctionBox(or,for12 volt models, the low voltage transformer) is located
at least eight (8) inches (20.3 cm) above ground level and at least 48 inches
(1.219 m) from the edge of the pool; see Figure 1 on page 7.
• Thelightxtureandallmetalitemswithinve(5)feet(1.524m)ofthepoolare
properly electrically bonded.
• Thewetnicheisproperlyinstalledsothatthetopedgeoftheunderwaterlight’s
lens is at least 18 inches below the surface of the water in the pool; see Figure 1
on page 7.
• ThewetnicheisproperlyelectricallybondedandgroundedviatheNo.8AWG
ground connector located at the rear of the niche; see Figure 1 on page 7.
• To be certain that the pool’s electrical system meets all applicable
requirements, the electrician should also consult the local building
department. Note: Use only Pentair wet niches to insure proper bonding and
grounding connections.
3
Switch power on to the light. A white light will momentarily illuminate, followed by the pre-
viously selected color. To select a color show mode (1-7) or fixed color (8-12), turn the wall
switch off/on a specific number of times. Each number (1-12) shown below corresponds to
the number of times to power-cycle the switch to activate a color light show or fixed color.
For details about saving color effects while in “show” modes, see “Hold” and “Recall” fea-
ture on page 4. Example: To select California Sunset Mode; turn the light on, then turn off
and on six times. During the off/on switching process, no illumination will occur,
During the off/on switching process, before the selected color is displayed,
no illumination will occur for a brief second. This operating
mode is normal during the switching process. During this period the pool and spa will be
dark and precautions should be taken to avoid unforeseen accidents. Failure to observe
this warning may result in serious injury or death to pool and spa users.
Using the IntelliBrite Controller (sold separately, P/N 600054), IntelliBrite 5G color pool/spa
lights can all be synchronized so that individual or multiple IntelliBrite lights all lights can be
switched on and off together.
To select a color light show mode or fixed color mode, rotate the dial so that it points to
the desired selection.
Hold and Recall Feature: When IntelliBrite color lights are powered on, the
previously selected color will be displayed, unless the HOLD or RECALL feature was
previously enabled.
Hold button/LED: Press this button (LED on) to capture and save a color effect while
displaying one of the light show modes. When the button is pressed, the LED will be on,
indicating that the color effect is captured.
Recall Button/LED: Use this button (LED on) to activate the last saved color effect.
When the button is pressed, the LED will be on, indicating that the color effect is being
displayed.
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
The following removal and installation instructions describe how to remove and
install the IntelliBrite pool and spa light assembly. Also use these instructions
after completing the following light replacement procedure:
IntelliBrite Spa Light and Face Ring Gasket and Lens Removal and
Installation instructions, on page 19.
1. WARNING! Switch off main electrical switch or circuit breaker, and the
switch which operates the IntelliBrite underwater light.
2. To remove light fixture assembly from the pool. Remove the special
bronze pilot screw at top of face ring. Remove the IntelliBrite light assembly
from the niche and place it on the deck.
3. Cut the cord about 12 inches (30.5 cm) from the back of the light
assembly.
4. Remove Junction Box cover, disconnect the light fixture wires, and
pull the cord through the conduit. Tip: Before pulling the cord, tape
the new cord to the existing cord, This might make it easier to
feed the new cord through the conduit (see following step).
5. Feed the new light fixture cord through the conduit from the niche
to the Junction Box. Note: Depending on the length of the conduit,
special tools may be required to pull the cord through the conduit.
6. Leave at least four (4) feet of cord to coil around the light fixture;
see Figure 1 on page 6. This four (4) feet (1.2192 m) of cord coiled
around the light allows the light to be serviced after the pool is filled
with water.
7. Cut the cord at the Junction Box, leaving at least size (6) inches of
cord to make connections.
8. Strip six (6) inches (15.2 cm) of the outer cord jacket from the cord
to expose the three insulated conductors. Be careful not to damage
the insulation on the three (3) inner conductors). Strip a 1/2” of insulation
Failure to bring the pool or spa’s electrical system up to code requirements
before installing the underwater light will create an electrical hazard which
could result in death or serious injury to pool users, installers, or others due
to electrical shock, and may also cause damage to property.
Replacing the IntelliBrite® 5G Pool and Spa
Light Assembly
(After Electrical Requirements Are Met)
4
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
Use only the special pilot screw provided with this
underwater light. This screw mounts and electrically grounds the housing
securely to the mounting ring and wet niche. Failure to use the screw
provided could create an electrical hazard which could result in death or
serious injury to pool users, installers or others due to electrical shock.
13. Final check for proper IntelliBrite light operation: Switch on
the main switch or circuit breaker to the system, and the switch
that operates the IntelliBrite underwater light itself. The light should
illuminate when power is applied. If not recheck the installation steps
starting with Step 1 (page 4).
9. Connect the three light wires (or two wires) to the corresponding light
circuit wires in the Junction Box. For three wires; connect the black
wire to power, white wire to common, and the green wire to ground.
10. For two wires connect the corresponding circuit wires (match the wire
colors) in the Junction Box. Secure the Junction Box cover.
11. Install the IntelliBrite® light assembly into the pool niche. Be sure to
insert the TAB on the lower part of the face ring into the niche SLOT
(located on the lower part of the niche). This is important to secure
the lower part of the light assembly onto the niche before tightening
the pilot screw.
12. Carefully tighten the special bronze pilot screw to secure the upper
part of the light assembly onto the niche.
IntelliBrite 5G Pool Light
Pilot screw (bronze)
IntelliBrite 5G Spa Light
Pilot screw (bronze)
Face ring TAB
(insert into
niche slot)
5
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
The following describes how to install the IntelliBrite® Pool Light fixture and
the IntelliBrite Spa Light fixture. Read page 4 before starting the installation
procedure.
Be sure that the pool or spa meets the requirements of the current National
Electrical Code (N.E.C.) Article 680-22 and all local codes and ordinances.
A licensed or certified electrician must install the electrical system to meet or
exceed those requirements before the underwater light is installed. Some of
the requirements of the National Electrical Code which the pool’s electrical
system must meet are as follows:
BEFORE STARTING: The following steps 1-7 (page 7-8) describe the tasks
that must be completed by the electrician before the IntelliBrite light fixture
is installed. See Figure 1 diagram on page 7.
Note: To be certain that the pool or spa electrical system meets all
applicable requirements, the electrician should also consult the local
building department.
Note: Use only Pentair wet niches to insure proper bonding and grounding
connections.
• ThelightingcircuithasaGroundFaultCircuitInterrupter(GFCI)forline
voltage models, and has an appropriately rated circuit breaker.
• TheJunctionBox(or,for12 volt models, the low voltage transformer) is
located at least eight (8) inches (20.3 cm) above ground level and at least
48 inches (1.219 m) from the edge of the pool; see Figure 1 on page 7.
• Thelightxtureandallmetalitemswithinve(5)feet(1.524m)ofthe
pool are properly electrically bonded.
• Thewetnicheisproperlyinstalledsothatthetopedgeoftheunderwater
light’s lens is at least 18 inches below the surface of the water in the pool;
see Figure 1 on page 7.
• Thewetnicheisproperlyelectricallybondedandgroundedviathe
No. 8 AWG ground connector located at the rear of the niche; see
Figure 1 on page 7.
INTELLIBRITE® 5G POOL AND SPA LIGHT FIXTURE INSTALLATION
(NEW POOL CONSTRUCTION)
6
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
1. Route light cable through conduit to Junction Box, leaving at least four
(4) feet of cable at the light fixture to coil around the light (this allows
the light to be serviced after the pool is filled with water). See Figure 1
below.
11.50"
16"
48"
min.
4" min.
Coil 4 ft. of light
cable around fixture.
18" min. to top of Lens.
8" min. Junction Box or
low Voltage Transformer.
#8 AWG Ground
Connector bonding
is located at rear
of Niche.
Rigid
Conduit
To GFCI, Circuit
Breaker and
Power Source.
Concrete must be cut
back around Niche to
allow for a compacted
plaster seal.
Pilot screw @12 o'clock position
Figure 1.
To install the IntelliBrite® Pool Light and Spa Light fixture:
INSTALLING THE INTELLIBRITE® 5G POOL AND SPA LIGHT
FIXTURE (AFTER ELECTRICAL REQUIREMENTS ARE MET)
2. Cut the cable at the Junction Box, leaving at least six (6) inches (2.4 cm) of
cord to make connections.
3. Strip back six (6) inches (2.4 cm) of the outer cord jacket to expose the three
insulated conductors (be careful not to damage the insulation on the three
(3) inner conductors). Strip a 1/2” of insulation off the three conductors. Be
careful not to damage the copper conductor.
4. Connect all three (3) conductors to the corresponding circuit wires in the
Junction Box and secure the Junction Box cover in place.
FOR LIGHT OPERATION, ONLY USE A SAFETY ISOLATION
TRANSFORMER.
Note: Connect three wires (or two wires) to the corresponding circuit
wires in the Junction Box. For three wires connect: Black wire to
power, white wire to common, and green wire to ground.
7
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
5. Install the IntelliBrite® Light assembly into the niche and tighten the special
bronze pilot screw.
Use only the special pilot screw provided with this
underwater light. This screw mounts and electrically grounds the housing
securely to the mounting ring and wet niche. Failure to use the screw
provided could create an electrical hazard which could result in death or
serious injury to pool users, installers or others due to electrical shock.
6. Fill the pool until the underwater light is completely submerged in water
before operating the light.
7. Final check for proper light operation: To check for proper operation,
switch on the main switch or circuit breaker, and the switch that operates the
IntelliBrite underwater light itself. The light should illuminate when power is
applied. If not recheck the installation steps starting with Step 1 (page 7)
FOR INTELLIBRITE POOL AND SPA LIGHT REMOVAL AND
INSTALLATION INSTRUCTIONS SEE:
• Replacing the IntelliBrite® 5G Pool and Spa Light
Assembly instructions, on page 3.
Replacing the IntelliBrite Spa Light Face Ring and
Gasket or Gasket and Lens instructions, on page 19.
Pilot screw (bronze)
IntelliBrite 5G Spa Light
Pilot screw (bronze)
IntelliBrite 5G Pool Light
8
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
Troubleshooting
Problem Cause/Action
Light does not function properly Check the light wiring connection to the junction box
at the pool side and to the AC power switch.
Be sure that there is proper AC power applied to
the light.
The light will not illuminate. Check the GFCI ground fault wiring and reset if
necessary.
IntellliBrite 5G 12 V Light with Light Fuse
Assembly
Replace FUSE assembly (see page 12):
Note: Replacing the fuse assembly may or may
not resolve this problem. In some instances the
fuse assembly will blow, and after replacing the
fuse the light’s circuit board is still not functional.
IntelliBrite® 5G Pool Light (12V) Fuse Harness Replacement
The following describes how to replace the IntelliBrite 5G Pool Light fuse assembly (if
applicable) and the light main circuit board for the IntelliBrite 5G pool light.
IMPORTANT! Before replacing the fuse assembly note the following:
REPLACING THE INTELLIBRITE POOL LIGHT CIRCUIT BOARD
ASSEMBLY (IN AN EXISTING POOL)
9
1. Turn off main electrical switch or circuit breaker, as well as the switch which
operates the IntelliBrite light itself.
2. Before starting make sure that you have a new lens gasket (P/N 79101601) and
a IntelliBrite 5G pool light circuit board assembly (P/N 619875Z - 300w,
P/N 619916Z-400W, P/N 619917Z- 500w) ready to install (see page 11).
Removal and Installation of IntelliBrite 5G Light Circuit Board
D A N G E R !
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION
Always disconnect power to the pool light at the circuit breaker
before servicing the light. Failure to do so could result in death
or serious injury to installer, service person, pool users, or
others due to electrical shock.
When replacing or reassembling the IntelliBrite Pool Circuit Board, the
Gasket (P/N 79101601) or Gasket and Lens (619864Z) MUST ALSO BE
REPLACED - SEE PAGE 18 FOR PART NUMBERS
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
3. REMOVING THE INTELLIBRITE 5G POOL LIGHT ASSEMBLY: Remove
the pilot screw at top of face ring, remove the light assembly from the niche.
Place the assembly on the deck. Note: It is not necessary to drain down the
pool.
4. Unwind the cord from the base of the light housing.
Be sure to keep the pilot screw from the IntelliBrite light. This screw
mounts and electrically grounds the housing securely to the mounting
ring and wet niche. Failure to use the screw provided could create an electrical hazard
which could result in death or serious injury to pool users, installers or others due to
electrical shock.
REPLACING THE INTELLIBRITE® 5G POOL LIGHT CIRCUIT BOARD
ASSEMBLY (IN AN EXISTING POOL) (Continued)
Replace the light circuit board assembly with the same type and
wattage. Failure to replace the light circuit board assembly with
the same type will damage the light assembly and may cause an electrical hazard
resulting in death or serious injury to pool users, installers, or others due to
electrical shock, and may also cause damage to property.
Always install a new lens gasket (P/N 79101601) whenever
disassembling the IntelliBrite light assembly. Failure to do so may
permit water to leak into the assembly which could cause:
(a) an electrical hazard resulting in death or serious injury to pool users,
installers, or others due to electrical shock, or
(b) breakage of the lens, which likewise could result in serious injury to pool
users, installers, or bystanders, or in damage to property.
10
IntelliBrite 5G Pool Light
Pilot screw (bronze)
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
5. Place a cloth on the ground to
protect the lens. Turn the light
over so the lens is resting on
the cloth. Using a ¼” nut driver
and a #3 Phillips screwdriver,
remove the nut uni-tension wire
clamp. Place the nut aside for
reinstallation.
6. Remove the face ring and
wire clamp from the light
housing.
7. With the light resting on
its base, carefully pry off
the gasket to remove the
lens. Set the lens aside for
installation later. Discard the
gasket.
Note: A NEW LENS
GASKET
(P/N 79101601) MUST BE
USED EACH TIME THE
LIGHT IS REASSEMBLED.
See page 18 for
Replacement Kit part
numbers.
REPLACING THE INTELLIBRITE® POOL LIGHT CIRCUIT BOARD
ASSEMBLY (IN AN EXISTING POOL) (Continued)
uni-tension
wire clamp:
Remove nut
and screw
Face ring
Lens
Note: Note the current position of the lens at the pilot screw (12 o’clock)
position, before removing it from the fixture. “W” on the lens indicates wide
angle, “N” indicates narrow angle. For more information, see page 17.
Gasket
NOTE: For a pool light (12 V only. No internal step-down transformer)
that has a replacement FUSE ASSEMBLY, continue the procedure on
the next page. If the light does NOT have a replacable fuse assembly,
proceed to page 13.
11
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
Light housing
with circuit
board
Circuit board
terminals
Replaceable
fuse
harness
assembly
Fuse harness
(press down
to release)
Carefully remove
connector plug from
circuit board terminals
Replaceable fuse harness assembly
1. Using your fingers, carefully disconnect each fuse connector plug from the
circuit board terminals. Carefully lift each connector plug upward, with small
side-to-side movements while holding the circuit board terminals with a flat
screw driver. Then gradually disconnect the connector plug from the terminal.
Note: To avoid permanent damage to the circuit board, be sure not to pull the
terminals off the surface of the circuit board.
2. Once the fuse connector plugs are removed from the circuit board terminals,
separate the fuse assembly from the light wire harness by pressing down on the
fuse release lever, then gently pull apart.
REPLACING THE FUSE HARNESS ASSEMBLY (FOR 12 V LIGHTS ONLY)
3. Insert the new fuse harness connector into the light cable harness plug and snap
together.
4. Using your fingers to carefully connect each fuse connector plug onto the circuit
board terminals. Be sure not to press down to hard on the connector, this can
damage the terminal connections on the circuit board.
5. Continue with “INSTALLING THE INTELLIBRITE® 5G POOL LIGHT
ASSEMBLY WITH NEW GASKET” on page 13.
12
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
INSTALLING THE INTELLIBRITE® POOL LIGHT ASSEMBLY WITH NEW
GASKET (see illustration on next page)
4. Place the two new thermal strips (provided) over the circuit board studs in
the base of the light housing.
5. Place the light circuit board over the base studs and seat the circuit board
on top of the thermal strips. Be sure the two connecting wires are not caught
between the housing and the edge of the circuit board.
6. Using a ¼” nut driver, tighten each of the four (4) retaining nuts to a torque value
of 6.0 (minimum) to 8.0 (maximum) in-lbs to secure the circuit board. DO NOT
OVERTIGHTEN THE CIRCUIT BOARD NUTS.
Be sure to install ALL of the four (4) retaining nuts. These
nuts ensure proper electrical ground. Failure to install all of the retaining
nuts could create an electrical hazard which could result in death or serious
injury to pool users, installers or others due to electrical shock.
Continue on next page.
Retaining nut (4x)
Light housing
Thermal
strip (2x)
Circuit board
connector plugs
Circuit board
Circuit board
stud (4x)
1. Using a ¼” nut driver, carefully remove the four retainer nuts from the
light assembly (see illustration on next page). Place the nuts aside for
reinstallation.
2. Unplug the two connector plugs from the circuit board. Lift up the circuit
board and remove it from the light housing base.
3. Carefully lift off the old thermal strips from the base of the light housing base
and discard.
REMOVING THE LIGHT CIRCUIT BOARD ASSEMBLY 13
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
1. Install NEW GASKET ONTO LENS: Stretch the gasket around the
circumference of the lens. Be sure the gasket is installed evenly around the
lens.
2. ALIGN LENS/GASKET ONTO LIGHT HOUSING:
a) With the light housing resting on its base, place the lens/gasket on top of the
light housing.
b) Rotate the lens/gasket to align the letter “W” (“WIDE” angle) on the lens with
the brass nut in the housing (see diagram on page 14 for brass nut location).
Note: The IntelliBrite light lens ships from the factory in the ‘WIDE’ (W) angle
position. The “wide” position of the lens is typically used for lights located either
side of the pool. The “narrow” position of the lens is typically used for lights
located either end of the pool. To use the “NARROW” angle light beam, rotate the
lens/gasket to align the letter “N” on lens. Note: For more information about using
the “WIDE” and NARROW angle lens, see page 17.
Retaining nut (4x)
Light housing
Thermal
strip (2x)
Circuit board
connector plugs
Circuit board
Circuit board
stud (4x)
14
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
4. INSTALL UNI-TENSION CLAMP: With the hook ends of the circular uni-tension
clamp pointing down, spread the clamp and place it in the “U” recesses of the
locking levers. Be sure the hook ends of the clamp are located between the pair
of locking levers as shown below and that the wire clamp is properly engaged
with all of the lock levers.
5. Place a cloth on the ground to protect the lens. Turn the light over so the lens
is resting on the cloth. Be sure the orientation of the wire clamp and the bolt
connection is positioned at 45°.
6. Tighten the bolt and nut until the distance between the ends of the clamp equals
¼-inch or less. Continue on next page.
Position the wire clamp (nut and bolt) about 45°
between the PILOT SCREW and BOLT/NUT.
45°
PILOT
SCREW
Lock
lever
Align letter “W” (“WIDE”
angle) on lens/gasket with
pilot screw hole on face ring
and brass nut
ALIGN
“TOP” label
(use to align light
housing with pilot
screw on face
t
PILOT SCREW
(12 O’clock)
“W” ON LENS
BRASS NUT
ALIGN
For “NARROW” angle light
beam, rotate “N” to 12
O’clock position
¼-in or less
TOP
Uni-tension
clamp
15
INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide
7. Coil at least four (4) feet of cord around the light fixture
(see Figure 1 on page 6). This allows the light to be serviced
after the pool is filled with water.
8. Connect the three light wires (or two wires) to the corresponding light
circuit wires in the Junction Box. For three wire connection: Connect the
black wire to power, white wire to common, and the green wire to ground.
Secure the Junction Box cover.
9. Install the light assembly into the pool niche. IMPORTANT: Be sure to
insert the TAB on the lower part of the face ring into the niche SLOT
(located on the lower part of the niche). This is important to secure
the lower part of the light assembly onto the niche before tightening
the pilot screw.
10. Carefully tighten the special bronze pilot screw to secure the upper part
of the light assembly onto the niche.
11. Final check for proper IntelliBrite® Light operation: Switch on the
main switch or circuit breaker to the system and the switch that operates
the IntelliBrite light itself. The light should illuminate when power is
applied. If not recheck the installation steps starting with Step 1 (page 4).
IntelliBrite Pool Light
Face ring TAB
(insert into
niche slot)
16
Pilot screw (bronze)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88

Pentair INTELLIBRITE 5G Guide d'installation

Catégorie
Accessoires de piscine hors terre
Taper
Guide d'installation

dans d''autres langues