Pentair INTELLIBRITE 5G Guide d'installation

INTELLIBRITE® 5G White Pool and Spa LED Light Installation and User’s Guide

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

INSTALLATION AND

USER’S GUIDE

INTELLIBRITE® 5G

WHITE AND COLOR POOL AND SPA LIGHTS

INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide

Technical Support: Phone: (800) 831-7133 - Fax: (800) 284-4151

Web sites: www.pentairpool.com and www.staritepool.com:

Contents

IMPORTANT WARNING AND SAFETY INSTRUCTIONS...................................ii

IntelliBrite 5G Pool and Spa Lights Overview ....................................................1

Operating IntelliBrite Pool and Spa lights using a wall switch (12 VAC) ............ 1

Using an External Transformer for Multiple IntelliBrite 12 VAC Light ............. .....1

Powering on IntelliBrite 5G Lights .................................................................... 2

Selecting a light show mode or ﬁxed color ........................................................ 2

Replacing the IntelliBrite 5G Pool and Spa Light Assembly

(in an existing pool/after Electrical Requirements are met) ............................ 3/4

Installing the IntelliBrite 5G Pool and Spa Light Fixture

(new pool construction/ /after Electrical Requirements are met) ) .................. 6/7

IntelliBrite 5G Pool Light (12 V) Fuse Harness Replacement .......................... 9

Replacing the IntelliBrite 5G Pool Light Circuit Board Assembly

(in an existing pool) .......................................................................................... 9

Wide and Narrow Angle Lens Adjustment........................................................17

IntelliBrite 5G Pool Light Replacement Kit Part Numbers ................................18

Replacing the IntelliBrite Spa Light Face ring and Gasket

(P/N 640045) or Gasket and Lens (640046) ................................................... 19

IntelliBrite 5G Spa Light Replacement Kit Part Numbers ................................ 23

IntelliBrite Color Light Controller ..................................................................... 24

Always install a new lens gasket (see part number in this

User’s Guide on page 9 and 19), when ever reassembling

the light. Failure to do so may permit water to leak into the assembly which

could cause; (a) an electrical hazard resulting in death or serious injury to pool

users, installer, or others due to electrical shock, or (b) breakage of the lamp

or lens, which likewise could result in serious injury to pool user, installers, or

bystanders, or in damage to property.

Before Installing luminaries read the following:

THE INTELLIBRITE 5G LED POOL LIGHT AND

SPA LIGHT CANNOT BE USED ON A DIMMER CIRCUIT. USING

A DIMMER SWITCH WILL RESULT IN PERMANENT DAMAGE TO

THE LIGHT.

P/N 619921 Rev K - 4/2015

FOR 12 VAC LUMINARIES: ALWAYS USE A SEPARATE STEP DOWN

TRANSFORMER TO POWER LUMINARIES. SEE DIAGRAM ON PAGE 7.

Note: Connect all three wires to the corresponding circuit wires in the

Junction Box (black wire to power, white wire to common, and green

wire to ground).

12 VAC LUMINARIES SPECIFICATION: 12 VAC, 50/60 Hz REPLACE ANY CRACKED

PROTECTIVE SHIELD (CRACKED LENS) WITH NEW LENS AND GASKET.

i

INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide

ii

Most states and local codes regulate the construction, installation,

and operation of public pools and spas, and the construction of

residential pools and spas. It is important to comply with these codes, many of which

directly regulate the installation and use of this product. Consult your local building and

health codes for more information.

SERIOUS BODILY INJURY OR DEATH CAN RESULT IF THIS LIGHT

IS NOT INSTALLED AND USED CORRECTLY.

INSTALLERS, POOL OPERATORS AND POOL OWNERS MUST

READ THESE WARNINGS AND ALL INSTRUCTIONS BEFORE

USING THE POOL AND/OR SPA LIGHT.

Before installing this product, read and follow all warning notices

and instructions in this Guide. Failure to follow warnings and

instructions can result in severe injury, death, or property damage.

Call (800) 831-7133 for additional free copies of these instructions. Please refer to www.

pentairpool.com for more information related to this products.

IMPORTANT NOTICE - Attention Installer: This Installation and User’s

Guide (“Guide”) contains important information about the installation, operation

and safe use of this underwater pool and spa light. This Guide should be given

to the owner and/or operator of this equipment.

IMPORTANT WARNING AND SAFETY INSTRUCTIONS

BEFORE WORKING ON POOL AND SPA LIGHTS always disconnect power

to the pool and/or spa lights at the circuit breaker from the light

before servicing the light. Failure to do so could result in death

or serious injury to service person, pool users or others due to

electric shock.

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION:

This underwater light must be installed by a licensed or certiﬁed electrician or a

qualiﬁed pool professional in accordance with the current National Electrical Code

(NEC), NFPA 70 or the Canadian Electrical Code (CEC), CSA C22.1. All applicable

local installation codes and ordinances must also be adhered to. Improper installation

will create an electrical hazard which could result in death or serious injury to pool

users, installers or others due to electrical shock, and may also cause damage

to property. Always disconnect the power to the pool light at the circuit breaker

before servicing the light. Failure to do so could result in death or serious injury to

serviceman, pool users or others due to electrical shock.

Important Safety Information for Pentair Water Pool and Spa Niche

and Light Installation

• AllNicheandLightinstallationsmustconformwithallcodes.Iflocalcodes

mandate a cord seal, use Pentair Water Pool and Spa plastic niches

(P/N 79206600 and P/N 79206700) and Cord Seal Kit (P/N 670044).

• Underno circumstances replace lights by splicing wire under water or behind

niche.

THE INTELLIBRITE® POOL AND SPA LIGHT REqUIRE HIGH vOLTAGE WHICH

CAN SHOCK, BURN, OR CAUSE DEATH.

Before Installing luminaries read the following:

READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL.

INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide

For countries in compliance with International Electromechnical

Commission (IEC) regulatory standards: The light ﬁxture must

be installed by a licensed or certiﬁed electrician or a qualiﬁed pool service person, in

accordance with IEC 364-7-702 and all applicable local codes and ordinance. Improper

installation will create an electrical hazard, which could result in death or serious injury

to pool user, installer or other due to electrical shock and may also cause damage to the

property.

iii

IMPORTANT WARNING AND SAFETY INSTRUCTIONS

RISK OF ELECTRIC SHOCK AND INJURY. USE ONLY THE

(*) Note: Wet-niche luminaires complying with requirements for both uses may bare

both the Listed Wet-Niche Submersible Luminaires UL Mark. A luminaire not bearing the

corresponding UL Listing Mark is not considered by UL to have been produced under UL’s

Listing and Follow-Up Service for the associated usage location.

CAUTION - The IntelliBrite® 5G Light ﬁxture must only be used with Pentair Water Pool

and Spa ﬁxture housings (niches). If the IntelliBrite light ﬁxture is installed into other

niches, the installation will not carry U.L. approval and will void all warranties.

Salt is an inherently corrosive material. While the levels of salt required

for proper operation of an electronic chlorine generator are relatively low

when compared to sea water and other salt solutions, placing any amount of salt in your

pool increases the likelihood of corrosion or other deterioration of pool equipment and any

surfaces used in and around your pool. Metal parts and certain natural and man-made

surfaces are particularly susceptible to corrosion and deterioration when used in and

around salt water pools. Pentair does not represent or otherwise guarantee that the proper

use of an electronic chlorine generator will prevent corrosion or other deterioration of pool

equipment and any surfaces used in and around your pool. Consult your experienced

pool professional, who should be able to advise you on the proper material selection,

installation techniques for those materials, and the proper use, care and maintenance of

those materials for your speciﬁc pool type and location in order to minimize the corrosion

and deterioration that is inherent in and around salt water pools.

INSTALLATION METHOD SPECIFIED BELOW.

NOTICE: The external ﬂexible cable or cord of this luminaire cannot be replaced; if

the cord is damaged, the luminaire shall be destroyed.

- REPLACE ANY CRACKED PROTECTIVE SHIELD (CRACKED LENS) WITH NEW

LENS AND GASKET. FOR MORE INFORMATION SEE PAGE 11.

- FOR LIGHT OPERATION, ONLY USE A SAFETY ISOLATION TRANSFORMER.

POOL AND SPA FIXED LUMINARIES: Follow these guidelines when installing,

replacing or repairing Pentair Aquatic Systems Pool and Spa ﬁxed luminaries:

Location of Pentair Water Pool and Spa Fountain Required Installation Method

Luminaire Use Fixture* (P/N 560001 and P/N 560000)

Swimming Pool Wet-Niche Swimming Pool Fixture Housing (Forming Shell) ONLY.

and Spa (or Spa) Luminaire (Light) DO NOT USE Fountain Fixture Stand.

Fountain Wet-Niche Submersible Luminaire (Light) Fixture Housing (Forming Shell) or

swimming Pool (or Spa) Luminair (Light) Fountain Fixture Stand

CAUTION! Luminaires not suitable for direct mounting

on normally ﬂammable surfaces (suitable ONLY for

mounting on non-combustible surfaces.

Surface Mount

Fixed pool and spa luminaries speciﬁcation:

12 VAC 50/60 Hz - 120VAC ,50/60 Hz.

INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide

IntelliBrite® 5G Pool and Spa Lights Overview

Operating Pool and Spa Lights Using a Wall Switch (12 VAC)

IntelliBrite 5G pool and spa lights can be manually controlled using a standard wall-mount

light switch. Multiple IntelliBrite lights can be connected via a junction box to a single

switch so that all lights can be switched on and off together. IntelliBrite lights can also be

automatically controlled via Pentair IntelliTouch®, EasyTouch® and SunTouch® Control

Systems. Note: Multiple IntelliBrite 5G pool/spa lights can also be controlled using

the IntelliBrite Controller, for more information see page 2.

Using an External Transformer for Multiple IntelliBrite 12 VAC Lights

When using multiple IntelliBrite 12 VAC lights on a 300 Watt transformer, it is

recommended that no more than three IntelliBrite pool lights and one (1) IntelliBrite Spa

light be used. It is also recommended not to exceed 100 feet of total cable run between

the transformer and light. Note: For long cable lengths, set transformer to 14 VAC

(see diagrams below).

300 Watt

Transformer J Box

12 Gauge

(Minimum)

100 ft.

300 Watt

Transformer J Box

12 Gauge

(minimum)

150 ft. max. for spa light

200 ft. max. for pool light

1

This manual describes how to install the IntelliBrite 5G white and color pool light and the

IntelliBrite 5G white and color spa light.

The IntelliBrite 5G white light provides a brilliant white light for a spectacular effect in

your pool and spa. The IntelliBrite 5G white light lens geometry (pool light only) provides

a choice between two light beam shapes; wider coverage with less intensity, or narrower

coverage with more intensity.

The IntelliBrite 5G color light provides brilliant vivid multi-colors with spectacular effects

for your pool and spa. Choose one of the seven pre-programmed color light shows or

select one of the ﬁve ﬁxed colors to create virtually endless range of dramatic underwater

lighting effects for a spectacular effect in your pool and spa.

INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide

Powering on IntelliBrite® 5G Color Lights

2

When the IntelliBrite light is powered on, a momentarily white light will illuminate,

followed by the previously selected color. Note: If power to the light is off for more

than ﬁve (5) seconds, the last color show mode or ﬁxed color that was saved will be

displayed.

Selecting a light show mode or ﬁxed color

Switch power on to the light. A white light will momentarily illuminate, followed by the pre-

viously selected color. To select a color show mode (1-7) or ﬁxed color (8-12), turn the wall

switch off/on a speciﬁc number of times. Each number (1-12) shown below corresponds to

the number of times to power-cycle the switch to activate a color light show or ﬁxed color.

For details about saving color effects while in “show” modes, see “Hold” and “Recall” fea-

ture on page 4. Example: To select California Sunset Mode; turn the light on, then turn off

and on six times. During the off/on switching process, no illumination will occur,

Saving a Color Mode or Fixed Color: When power is switched off to the IntelliBrite

color lights, the last color show mode or ﬁxed color will be saved. The next time the light

is powered on, the previously saved color show mode or ﬁxed color will be displayed.

For example, while in “Party Mode” switch the light off. Wait more than 10 seconds,

switch the light back on to resume “Party Mode.”

During the off/on switching process, before the selected color is displayed,

no illumination will occur for a brief second. This operating

mode is normal during the switching process. During this period the pool and spa will be

dark and precautions should be taken to avoid unforeseen accidents. Failure to observe

this warning may result in serious injury or death to pool and spa users.

1 SAm Mode: Cycles through

white, magenta, blue and

green colors (emulates

the Pentair SAm® color

changing light).

2 Party Mode: Rapid color

changing building energy

and excitement.

3 Romance Mode: Slow

color transitions creating a

mesmerizing and calming

effect.

4 Caribbean Mode: Transitions

between a variety of blues

and greens.

5 American Mode: Patriotic

red, white and blue

transition.

6 California Sunset Mode:

Dramatic transitions of

orange, red and magenta

tones.

7 Royal Mode: Richer, deeper

color tones.

8 Blue: Fixed color.

9 Green: Fixed color.

10 Red: Fixed color.

11 White: Fixed color.

12 Magenta: Fixed color.

13 Hold: Save the current color

effect during a color light

show.

14 Recall: Activate the last

saved color effect.

Number of times to cycle power (1-5)

Number of times to cycle power (6-14)

Using the IntelliBrite Controller (sold separately, P/N 600054), IntelliBrite 5G color pool/spa

lights can all be synchronized so that individual or multiple IntelliBrite lights all lights can be

switched on and off together.

Using an IntelliBrite Color Light Controller

INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide INTELLIBRITE® 5G Pool and Spa Lights Installation and User’s Guide

Risk of Electrical Shock or Electrocution!

This underwater light must be installed by a licensed or certiﬁed

electrician or a qualiﬁed pool professional in accordance with

the National Electrical Code and all applicable local codes and

ordinances. Improper installation will create an electrical hazard

which could result in death or serious injury to pool users,

installers or others due to electrical shock, and may also cause

damage to property. Always disconnect the power to the pool

light at the circuit breaker before servicing the light. Failure to

do so could result in death or serious injury to serviceman, pool

users or others due to electrical shock.

Replacing the IntelliBrite® 5G Pool and Spa

Light Assembly (in an existing pool or spa)

Verify that the pool and spa meets the requirements of the current National Electrical Code

and all local codes and ordinances. A licensed or certiﬁed electrician must install the

electrical system to meet or exceed those requirements before the underwater light is

installed. Some of the requirements of the National Electrical Code which the pool’s

electrical system must meet are as follows:

• ThelightingcircuithasaGroundFaultCircuitInterrupter(GFCI)forlinevoltage

models, and has an appropriately rated circuit breaker.

• TheJunctionBox(or,for12 volt models, the low voltage transformer) is located

at least eight (8) inches (20.3 cm) above ground level and at least 48 inches

(1.219 m) from the edge of the pool; see Figure 1 on page 7.

• Thelightxtureandallmetalitemswithinve(5)feet(1.524m)ofthepoolare

properly electrically bonded.

• Thewetnicheisproperlyinstalledsothatthetopedgeoftheunderwaterlight’s

lens is at least 18 inches below the surface of the water in the pool; see Figure 1

on page 7.

• ThewetnicheisproperlyelectricallybondedandgroundedviatheNo.8AWG

ground connector located at the rear of the niche; see Figure 1 on page 7.

• To be certain that the pool’s electrical system meets all applicable

requirements, the electrician should also consult the local building

department. Note: Use only Pentair wet niches to insure proper bonding and

grounding connections.

3