Whirlpool WRX986SIHV Manuel utilisateur

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING or

PROBLEM SOLVER, please visit our website at www.whirlpool.com for additional information. If you still need assistance, call us

at 1-800-253-1301. In Canada, visit our website at www.whirlpool.ca or call us at 1-800-807-6777.

You will need your model and serial number, located on the inside wall of the refrigerator compartment.

Table of Contents / Índice / Table des matières

REFRIGERATOR SAFETY .......................2

Proper Disposal of

Your Old Refrigerator.............................3

INSTALLATION INSTRUCTIONS............3

Unpack the Refrigerator.........................3

Remove and Replace

Refrigerator Doors..................................4

Remove and Replace Drawer Fronts ....7

Location Requirements..........................9

Electrical Requirements.........................9

Water Supply Requirements..................9

Connect the Water Supply ..................10

Handle Installation and Removal.........11

Refrigerator Leveling,

Door Closing and Alignment................12

FILTERS AND ACCESSORIES..............13

Water Filtration System........................13

Install Air Filter......................................14

Accessories..........................................15

REFRIGERATOR USE............................15

Opening and Closing Doors ................15

Using the Controls ...............................15

Refrigerator Features ...........................18

Water and Ice Dispensers....................19

Ice Maker and Ice Storage Bin ............22

REFRIGERATOR CARE.........................22

Cleaning ...............................................22

Lights....................................................23

Vacation and Moving Care ..................23

PROBLEM SOLVER...............................24

WATER FILTER CERTIFICATIONS.......29

PERFORMANCE DATA SHEET ............30

WARRANTY............................................31

SEGURIDAD DEL REFRIGERADOR.....32

Cómo deshacerse adecuadamente

de su refrigerador viejo ........................33

INSTRUCCIONES DE INSTALACIÓN...33

Desempaque el refrigerador ................33

Cómo quitar y volver a colocar

las puertas del refrigerador..................34

Cómo quitar y volver a colocar

los frentes de los cajones ....................36

Requisitos de ubicación.......................38

Requisitos eléctricos............................39

Requisitos del suministro de agua.......39

Conexión del suministro de agua ........39

Instalación y remoción

de las manijas.......................................41

Nivelación del refrigerador, cierre

y alineamiento de las puertas ..............42

FILTROS Y ACCESORIOS.....................43

Sistema de filtración de agua ..............43

Instalación del filtro de aire ..................44

Accesorios............................................45

USO DE SU REFRIGERADOR...............46

Cómo abrir y cerrar las puertas ...........46

Uso de los controles ............................46

Características del refrigerador............49

Despachadores de agua y hielo ..........49

Fábrica de hielo y depósito de hielo....53

CUIDADO DE SU REFRIGERADOR .....53

Limpieza ...............................................53

Luces....................................................54

Cuidado durante las

vacaciones y mudanzas.......................55

SOLUCIÓN DE PROBLEMAS................56

HOJA DE DATOS

DEL RENDIMIENTO ...............................62

GARANTÍA...............................................63

SÉCURITÉ DU RÉFRIGÉRATEUR........ 65

Mise au rebut adéquate de

votre vieux réfrigérateur....................... 66

INSTRUCTIONS D’INSTALLATION...... 66

Déballage du réfrigérateur................... 66

Retrait et réinstallation des

portes du réfrigérateur......................... 67

Retrait et réinstallation

de l'avant des tiroirs ............................ 69

Exigences d'emplacement.................. 71

Spécifications électriques ................... 72

Spécifications de

l’alimentation en eau............................ 72

Raccordement à la

canalisation d'eau................................ 72

Installation et démontage

des poignées ....................................... 74

Mise à niveau du réfrigérateur,

fermeture et alignement des portes.... 75

FILTRES ET ACCESSOIRES................. 76

Système de filtration d'eau.................. 76

Installation du filtre à air....................... 77

Accessoires ......................................... 78

UTILISATION DU RÉFRIGÉRATEUR ... 78

Ouverture et fermeture des portes...... 78

Utilisation des commandes................. 78

Caractéristiques du réfrigérateur ........ 81

Distributeurs d'eau et de glaçons ....... 82

Machine à glaçons et bac

d’entreposage à glaçons..................... 85

ENTRETIEN DU RÉFRIGÉRATEUR ..... 86

Nettoyage ............................................ 86

Lampes................................................ 87

Entretien avant les vacances

ou lors d’un déménagement ............... 87

RÉSOLUTION DE PROBLÈMES .......... 88

FEUILLE DE DONNÉES

SUR LA PERFORMANCE...................... 94

GARANTIE.............................................. 95

REFRIGERATOR

USER INSTRUCTIONS

W10505281A

2

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ Use a sturdy glass when dispensing ice (on some models).

■ Do not hit the refrigerator glass doors (on some models).

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

3

Proper Disposal of

Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

– even if they will sit for “just a few days.” If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

■ Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see “Refrigerator Safety.”

■ Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in “Refrigerator Care.”

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as floor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

4

Remove and Replace Refrigerator Doors

NOTE: Measure the width of your door opening, to see whether or not you need to remove the refrigerator doors to move the

refrigerator into your home. If door removal is necessary, see the following instructions.

IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator

control OFF. Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather the required tools and read all instructions before removing doors.

TOOLS NEEDED: ³⁄₁₆" hex key wrench and a #2 Phillips screwdriver

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Door Removal and Replacement

Wiring Plug

Top Left Hinge

Style 1 – Water Dispenser

Tubing Connection

A

A. Outer Ring

BA

C

A. ³⁄₁₆" Internal Hex-Head Screws

B. Ground Wire (Do Not Remove)

C. Do Not Remove Screws

Style 2 – Water Dispenser

Tubing Connection

A

A. Outer Ring

Top Right Hinge

A. ³⁄₁₆"

Internal Hex-Head Screws

B. Hinge Cover Screw

C. Top Hinge Cover

D. Top Hinge

C

B

A

D

Door Removal

5

Remove Right-Hand Refrigerator Door

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

3. Using a Phillips screwdriver, remove the cover from the Top

Hinge.

4. Using the ³⁄₁₆" hex key wrench, remove the two internal hex

head screws from the top hinge, and set aside.

NOTE: Do not remove the two locator screws. These screws

will help you align the hinge when you replace the door.

5. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

Remove Left-Hand Refrigerator Door

IMPORTANT: The tubing and wiring for the water dispenser run

through the left-hand door hinge, so they must be disconnected

before removing the door.

1. Using a Phillips screwdriver, remove the cover from the top

hinge.

2. Disconnect the water dispenser tubing located on top of the

door hinge.

Style 1 - Press the outer ring against the face of the fitting

and gently pull the dispenser tubing free.

NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

A. Top hinge cover screw

B. Top hinge cover

C.

³⁄₁₆

" Internal hex head screws

D. Top hinge

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

A

B

C

D

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

A. Top hinge cover screwB.Top hinge cover

A. Outer ring

B. Face of fitting

A

B

AB

6

Style 2 - Firmly pull up on the clasp. Then, pull the tubing out

of the fitting.

NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

3. Disconnect the wiring plug located on top of the door hinge.

■ Grasp each side of the wiring plug. With your left thumb,

press down to release the catch and pull the sections of

the plug apart.

NOTE: Do not remove the green, ground wire. It should

remain attached to the door hinge.

4. Using the ³⁄₁₆" hex key wrench, remove the two internal hex

head screws from the top hinge, and set aside.

NOTES:

■ Provide additional support for the refrigerator door while

the hinges are being removed. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

■ Do not remove the two locator screws. These screws will

help you align the hinge when you replace the door.

5. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges

and brake feet assemblies to move the refrigerator through a

doorway.

■ Only if necessary, use a driver with a #2 square bit tip to

remove the bottom hinges and a ³⁄₈" nut driver to remove

the brake feet screws.

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top of the

refrigerator door.

3. Using the two ³⁄₁₆" internal hex head screws, fasten the hinge

to the cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

1. Set the left-hand door onto the bottom hinge pin.

2. Using the two ³⁄₁₆" internal hex head screws, fasten the hinge

to the cabinet. Do not tighten the screws completely.

3. Reconnect the water dispenser tubing.

Style 1 - Insert the tubing into the fitting until it stops and the

outer ring is touching the face of fitting.

Style 2 - Insert the tubing firmly into the fitting until it stops.

Close the clasp around the tubing. The clasp snaps into place

between the fitting and the collar.

4. Reconnect the electrical wiring.

■ Push together the two sections of the wiring plug.

Final Steps

1. Completely tighten the four internal hex head screws (two on

the right-hand door hinge and two on the left-hand door

hinge).

2. Replace both top hinge covers.

A.

³⁄₁₆

" Internal hex head screws

B. Ground wire (do not remove)

C.Locator screws (do not

remove)

A B

C

7

Remove and Replace Drawer Fronts

Depending on the width of your door opening, it may be

necessary to remove the drawer fronts to move the refrigerator

into your home.

IMPORTANT:

■ If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator

control OFF, and unplug the refrigerator or disconnect power.

Remove food from the drawers.

■ Two people may be required to remove and replace the

drawer fronts.

Tools Needed: ¹⁄₄" Hex head nut driver, Flat-blade screwdriver

Refrigerated Drawer

Disconnect Wiring

NOTES:

■ The exterior refrigerator drawer front is connected to the

temperature control. Before removing the drawer front, the

wires must be disconnected from the temperature control.

■ The gray cable visible behind and under the pantry drawer at

the right side contains wiring for the pantry control and

moves with the drawer as it is pulled out. There is no need to

disconnect this cable.

1. Open the drawer to its full extension, and remove the large

interior bin.

2. Locate the wiring cover on the backside of the drawer front.

Press tab on the cover to release the snaps, and pull off cover

to reveal the wiring connection.

3. On one side of the wiring connector, insert the screwdriver

blade between the connector tab and the connector to

release. Repeat for the opposite side. Pull the wiring

connector apart.

Remove Drawer Front

1. Using a ¹⁄₄" hex head nut driver, remove the two bottom

screws (one on each side) attaching the drawer front to the

drawer glides.

2. Using ¹⁄₄" hex head nut driver, loosen the two top screws (one

on each side) attaching the drawer front to the drawer glides.

NOTE: Loosen the screws three to four turns. Keep the

screws in the drawer front.

3. Lift the drawer front up and off the drawer glide brackets.

4. Slide the drawer glides back into the refrigerator.

A. Press tab B. Wiring connection cover

B

A

A. Loosen top screws

B. Drawer glide bracket

C. Remove bottom screws

A

C

B

8

Replace Drawer Front

1. Pull out the drawer glides until they are fully extended.

2. Lower the loosened screws in the top of the drawer front into

the upper notches in the drawer glides.

NOTE: It helps if one person holds the drawer glides steady

while another person aligns the drawer front and inserts the

screws into the notches.

3. Align the holes in the bottom of the drawer front with the

holes in the bottom of the drawer glides and fasten with the

screws removed earlier.

4. Tighten the two top screws.

Reconnect Wiring

1. Align the two ends of the wiring connector and push them

together until you hear a “click” sound and feel the tabs snap

into place on the connector.

2. Gently pull on the wiring connection to ensure the wiring

connection is completely seated. Replace the wiring cover.

NOTE: The wiring connection must be complete for the

drawer temperature control to operate.

3. Replace the interior bin.

Freezer Drawer

Remove Drawer Front

1. Open the freezer drawer to its full extension.

2. Loosen the two top screws that fasten the drawer front to the

drawer glides. The two screws (one on the left-hand side and

one on the right-hand side) are located inside the drawer

front.

3. Lift up on the drawer front to release the plastic studs from

the drawer glide bracket slots.

4. Slide the drawer glides back into the freezer.

Replace Drawer Front

1. Pull out the freezer drawer glides to their full extension.

2. Holding the drawer front by its sides, align the two plastic

studs, located at the bottom, inside the drawer front, with the

drawer glide bracket slots.

NOTE: It helps if one person holds the drawer glides steady

while another person aligns the drawer front and inserts the

studs into the slots.

3. Replace and tighten the two screws at the top of the drawer

front (one on the left-hand side and one on the right-hand

side).

Final Steps

1. Plug into a grounded 3 prong outlet.

2. Reset the controls. See “Using the Control(s)” and

“Temperature Controlled Exterior Drawer.”

3. Return all removable parts and the food to the drawers.

A. Drawer glide bracket slots

A

A. Drawer front screw

B. Drawer front plastic stud

A

B

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

9

Location Requirements

IMPORTANT: This refrigerator is designed for indoor, household

use only.

To ensure proper ventilation for your refrigerator, allow for a ¹⁄₂"

(1.25 cm) of space on each side and at the top. Allow for a 1"

(2.54 cm) space behind the refrigerator. If your refrigerator has an

ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 3³⁄₄" (9.5 cm) minimum space between the refrigerator

and wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature range

for optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn Cooling OFF, and then disconnect the

refrigerator from the electrical source. When you have finished,

reconnect the refrigerator to the electrical source and turn

Cooling ON. See “Using the Control(s).”

Water Supply Requirements

A cold water supply with water pressure between 35 and 120 psi

(241 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call a

licensed, qualified plumber.

NOTE: If the water pressure is less than what is required, the flow

of water from the water dispenser could decrease or ice cubes

could be hollow or irregular shaped.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy use. The tank capacity could be too small to keep

up with the requirements of the refrigerator.

NOTE: Faucet mounted reverse osmosis systems are not

recommended.

■ If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See “Water

Filtration System.”

If you have questions about your water pressure, call a licensed,

qualified plumber.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

3³⁄₄" (9.5 cm)

¹⁄₂" (1.25 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

10

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■ Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

■ The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX

(cross-linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator

are acceptable, and will help avoid off-taste or odor in your

ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the

following Whirlpool Part Numbers:

W10505928RP (7 ft [2.14 m] jacketed PEX),

8212547RP (5 ft [1.52 m] PEX), or

W10267701RP (25 ft [7.62 m] PEX).

■ Install tubing only in areas where temperatures will remain

above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches

■ ¹⁄₄" nut driver

NOTE: Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve

which reduces water flow and clogs easier.

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water is

connected, turn the ice maker OFF.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by a

¹⁄₂" household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a

minimum ¹⁄₂" size household supply line is recommended.

4. Now you are ready to connect the copper tubing to the

shutoff valve. Use ¹⁄₄" (6.35 mm) OD soft copper tubing to

connect the shutoff valve and the refrigerator.

■ Ensure that you have the proper length needed for the

job. Be sure both ends of the copper tubing are cut

square.

■ Slip compression sleeve and compression nut onto

copper tubing as shown. Insert end of tubing into outlet

end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not

overtighten.

5. Place the free end of the tubing into a container or sink, and

turn on main water supply to flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve, to avoid possible

water valve malfunction.

6. Bend the copper tubing to meet the water line inlet, which is

located on the back of the refrigerator cabinet as shown.

Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Follow the connection instructions specific to your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a “P” clamp.

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

A. Sleeve

B. Nut

C. Copper tubing (to refrigerator)

D. Household supply line (½" minimum)

A

B

D

C

A. Compression sleeve

B. Compression nut

C. Copper tubing

A. Copper tubing

B. “P” clamp

C. Compression nut

D. Compression sleeve

B CA

B

A

C

D

11

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the

end of the water line inlet.

3. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet’s side wall or other parts inside the cabinet.

4. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

7. On some models, the ice maker is equipped with a built-in

water strainer. If your water conditions require a second water

strainer, install it in the ¹⁄₄" (6.35 mm) water line at either tube

connection. Obtain a water strainer from your appliance

dealer.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See “Water and Ice Dispensers.”

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill the ice storage bin.

Handle Installation and Removal

Parts Included: Refrigerator door handles (2), Refrigerator

drawer handle (1), Freezer drawer handle (1), ¹⁄₈" hex key, spare

setscrew(s)

Install Handles

Refrigerator Doors

NOTE: Handle mounting setscrews are preinstalled inside the

handle.

1. Remove the handles from the packaging inside the

refrigerator, and place them on a soft surface.

2. Open a refrigerator compartment door. On the closed door,

place a handle onto the shoulder screws so that the

setscrews are facing the adjacent door.

3. Firmly push the handle toward the door until the handle base

is flush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

5. Using a clockwise motion tighten the setscrew just until it

begins to contact the shoulder screw. Do not fully tighten.

6. Repeat steps 4 and 5 to fasten the lower setscrew.

7. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

8. Repeat steps 2 through 7 to install the other handle onto the

adjacent refrigerator door.

A. Household water line

B. Nut (purchased)

C. Ferrule (purchased)

D. Refrigerator water tubing

D

A B C

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

A. Shoulder screws

B. Setscrews inside the handle

A

B

12

Refrigerator and Freezer Drawers

1. With the drawer closed, place the handle onto the shoulder

screws so that the setscrews are facing down toward the

floor.

2. Firmly push the handle toward the drawer until the handle

base is flush against the drawer.

3. Insert the short end of the hex key into the left-hand hole and

slightly rotate the hex key until it is engaged in the setscrew.

4. Using a left to right motion tighten the setscrew a quarter-turn

at a time just until it begins to contact the shoulder screw. Do

not fully tighten.

5. Repeat steps 11 and 12 to fasten the right-hand setscrew to

the shoulder screw.

6. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

7. Save the hex key and all instructions.

Remove the Handles

1. While holding the handle, insert the short end of the hex key

into a setscrew hole and slightly rotate the hex key until it is

engaged in the setscrew.

2. Using a right to left motion loosen the setscrew a quarter-turn

at a time.

3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the

handle away from the door or drawer.

4. If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

Refrigerator Leveling, Door Closing

and Alignment

The base grille covers the adjustable brake feet and roller

assemblies located at the bottom of the refrigerator below the

freezer drawer. Before making any adjustments, remove the base

grille and move the refrigerator to its final location.

Tools Needed: ¹⁄₄" hex nut driver

Tools Provided: ¹⁄₈" hex key wrench

1. Remove the base grille. Using both hands, grasp the grille

firmly and pull it toward you. Open the freezer drawer to

access the brake feet.

NOTE: To allow the refrigerator to roll easier, raise the break

feet by turning them counterclockwise. The front rollers will

be touching the floor.

2. Move the refrigerator to its final location.

3. Using the ¹⁄₄" hex nut driver, lower the brake feet. Turn them

clockwise, until the rollers are off the floor and both brake feet

are snug against the floor. This keeps the refrigerator from

rolling forward when opening the refrigerator doors or freezer

drawer.

IMPORTANT: If you need to make further adjustments

involving the brake feet, you must turn both brake feet the

same amount to keep the refrigerator level.

4. Make sure the doors close easily. If you are satisfied with the

door opening and closing, skip the next section and go to

“Align the Doors.” If, however, the doors do not close easily

or the doors pop open, adjust the tilt.

To Adjust the Cabinet Tilt:

■ Open the freezer drawer. Use a ¹⁄₄" hex nut driver to turn

both brake feet clockwise the same amount. This will

raise the front of the refrigerator. It may take several turns

to allow the doors to close easier.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the brake feet. This

makes it easier to turn them.

Style 1

A. Shoulder screw

B. Setscrews inside the handle

A

B

A. Brake foot

B. Front roller

A

¹⁄₄"

B

13

Style 2

5. Make sure the doors are even at the top and that the space

between the bottom of the refrigerator doors and the top of

the freezer drawer is even. If necessary, align the doors.

To Align the Doors:

■ Keeping both refrigerator doors closed, pull out the

refrigerated drawer. Locate the bottom hinge pin of the

right-hand refrigerator door. The alignment screw is inside

the bottom hinge pin.

■ Insert the short end of the ¹⁄₈" hex key wrench (packed

with the Door Handle Installation Instructions) into the

bottom hinge pin until it is fully engaged in the alignment

screw.

To raise the door, turn the hex key to the right.

To lower the door, turn the hex key to the left.

■ Continue to turn the alignment screw until the doors are

aligned.

6. Make sure the refrigerator is steady. If the refrigerator seems

unsteady or rolls forward when a door or drawer is pulled

open, adjust the brake feet.

To Steady the Refrigerator:

■ Open the freezer drawer. Using a ¹⁄₄" hex driver, turn both

brake feet clockwise the same amount until the brake feet

are snug against the floor. Check again. If not satisfied,

continue to adjust the brake feet by half turns of the

screw until the refrigerator does not roll forward when the

drawer is opened.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the brake feet. This

makes it easier to turn the screws.

7. Replace the base grille by aligning the ends of the grille with

the leveling assemblies on each side and snapping the grille

into place.

FILTERS AND

ACCESSORIES

Water Filtration System

Install the Water Filter

1. Locate the accessory packet in the refrigerator and remove

the water filter.

2. Take the water filter out of its packaging and remove the

cover from the O-rings. Be sure the O-rings are still in place

after the cover is removed.

3. The water filter compartment is located in the right-hand side

of the refrigerator ceiling. Push up on the compartment door

to release the catch, then lower the door.

4. Align the arrow on the water filter label with the cutout notch

in the filter housing and insert the filter into the housing.

A. Brake foot

A. Bottom hinge pin

B. Turn to the right to raise.

C. Turn to the left to lower.

D.

¹⁄₈

" Hex key wrench

¹⁄₄"

A

B

C

D

A. O-ring cover

B. O-rings

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

B

A

14

5. Turn the filter clockwise 90 degrees (¹⁄₄ turn), until it locks into

the housing.

NOTE: If the filter is not correctly locked into the housing, the

water dispenser will not operate. Water will not flow from the

dispenser.

6. While the compartment door is still open, lift the filter up into

the compartment. Then, close the filter compartment door

completely.

7. Flush the water system. See “Flushing the Water Filter” in the

“Water and Ice Dispensers” section.

IMPORTANT: If you do not flush the water system, you may

experience dripping and/or decreased flow from the water

dispenser.

The Water Filter Status Light

Press OPTIONS on the control panel to launch the Options menu.

Press OPTIONS, under Filter Status, again to display the

percentage of filter life remaining (from 99% to 0%). Press ICE/

WATER, under Back, to return to the Normal screen.

The water filter status lights will help you know when to change

your water filter.

■ ORDER FILTER (yellow) - it is almost time to change the water

filter. While you are dispensing water, “Order Filter” will blink

seven times and sound an alert tone three times.

■ REPLACE FILTER (red) - Replace the water filter. While you

are dispensing water, “Replace Filter” will blink seven times

and an alert tone will sound three times.

■ RESET the water filter status tracking feature. After you

replace the disposable filter with a new filter, closing the filter

compartment door will automatically reset the filter status

tracking feature. See “Using the Control(s).”

NOTE: “REPLACE FILTER” will remain illuminated if a filter is

not installed or is installed incorrectly.

Replace the Water Filter

To purchase a replacement water filter, see “Accessories” in the

User Guide, Use and Care Guide or User Instructions.

Replace the disposable water filter when indicated on the water

filter status display or at least every 6 months. If water flow to

your dispenser or ice maker decreases noticeably, change the

water filter sooner.

1. Locate the water filter compartment in the right-hand side of

the refrigerator ceiling. Push up to release and lower the

compartment door.

2. Turn the water filter counterclockwise (to the left), and pull it

straight out of the compartment.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

3. Install the replacement water filter by following steps 2

through 7 in the “Install the Water Filter” section.

Install Air Filter

(on some models)

An air filter is 15 times more powerful than baking soda at

reducing common food odors inside the refrigerator.

On some models, your refrigerator's accessory packet includes

an air filter, which must be installed prior to use.

Installing the Air Filter

Install the air filter behind the vented door, located on the rear

wall near the top of the refrigerator compartment.

1. Remove the air filter from its packaging.

2. Lift open the vented door.

3. Snap the filter into place.

Installing the Filter Status Indicator

The filter comes with a status indicator, which should be

activated and installed at the same time the air filter is installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator until

the bubble pops to activate the indicator.

A. Air filter

A

MONTHS

REPLACE

15

3. Lift open the vented air filter door. On some models, there are

notches behind the door.

Models with notches:

■ With the indicator screen facing outward, slide the

indicator down into the notches.

NOTE: The indicator will not easily slide into the notches

if the bubble has not been popped.

■ Close the air filter door, and check that the indicator is

visible through the window in the door.

Models without notches:

■ Place the indicator somewhere it is easily visible - either

inside the refrigerator, or elsewhere in your kitchen or

home.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order a replacement air filter, contact us. See “Accessories” in

the User Guide, Use and Care Guide or User Instructions for

information on ordering.

1. Remove the used air filter by squeezing in on the side tabs.

2. Remove the used status indicator.

3. Install the new air filter and filter status indicator using the

instructions in the previous sections.

Accessories

The following accessories are available for your refrigerator. To

order an accessory, contact us and ask for the Part Number.

In the U.S.A., visit our webpage www.whirlpool.com/

accessories or call 1-800-901-2042.

In Canada, visit our webpage www.whirlpoolparts.ca

or call 1-800-807-6777.

affresh

®

Stainless Steel Cleaner:

In U.S.A., order Part #W10355016

In Canada, order Part #W10355016B

affresh

®

Stainless Steel Wipes:

In U.S.A., order Part #W10355049

In Canada, order Part #W10355049B

affresh

®

Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010

In Canada, order Part #W10355010B

Water Filter:

Order Part #W10413645A or FILTER2

Air Filter:

Order Part #W10311524 or AIR1

Produce Preserver Starter kit:

Order Part #P1UB6S1

Produce Preserver Refill kit:

Order Part #P1KC6R1

REFRIGERATOR USE

Opening and Closing Doors

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

■ When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

■ When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

Using the Controls

The controls are located above the external dispenser.

IMPORTANT: The display screen on the dispenser control panel

will turn off automatically and enter “sleep” mode when the

control buttons and dispenser paddles have not been used for

2 minutes or more. Press any control button to reactivate the

display screen. The home screen will appear as shown.

A. Status indicator window

B. Air filter status indicator

C. Notches

B

A

C

A. Hinged seal

A

16

Viewing and Adjusting Temperature Set Points

For your convenience, your refrigerator and freezer controls are

preset at the factory.

When you first install your refrigerator, make sure that the

controls are still set to the recommended set points. The factory

recommended set points are 37°F (3°C) for the refrigerator and

0°F (-18°C) for the freezer.

IMPORTANT:

■ Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the set points to a colder than

recommended setting will not cool the compartments any

faster.

■ If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

■ The recommended settings should be correct for normal

household use. The controls are set correctly when milk or

juice is as cold as you like and when ice cream is firm.

NOTE: Areas such as a garage, basement or porch, may

have higher humidity or extreme temperatures. You may need

to adjust the temperature away from the recommended

settings to accommodate for these conditions.

■ Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

View Temperature Set Points

1. Press and hold TEMP for 3 seconds to activate Temperature

mode.

NOTE: To view temperature in degrees Celsius, press the

LIGHT button, under Units, when adjust mode is activated. To

return the display setting to Fahrenheit, press the LIGHT

button again.

When Temperature mode is activated, press TEMP to toggle

between Fridge and Freezer. The display will show the

temperature set point of the selected compartment, and

temperature adjusting information will appear on the display

screen.

Recommended Refrigerator Temperature

Recommended Freezer Temperature

Adjust Temperature Set Points

Refrigerator set point range: 33°F to 45°F (0°C to 7°C).

Freezer set point range: -5°F to 5°F (-21°C to -15°C).

1. When Temperature mode is activated, press TEMPERATURE

to select the Refrigerator zone. The display will show the

temperature set point of the selected compartment, as

shown.

2. Press LOCK to raise the set point, or press OPTIONS to lower

the set point.

3. When you have finished viewing (and adjusting if desired) the

refrigerator set point, press TEMP, under Select Zone, to

change the display to show the freezer set point. When the

zone has been changed, “FREEZER” appears on the display

screen.

4. Press the LOCK button to raise the set point, or press the

OPTIONS button to lower the set point.

Save/Confirm Temperature Settings

■ When you have finished adjusting both the refrigerator and

freezer set points, press MEASURED FILL to confirm and to

save the settings.

NOTE: To exit Temperature mode without saving changes, press

the ICE/WATER button under Back at any time, or allow about

60 seconds of inactivity. The temperature mode will turn off

automatically and return to the normal screen.

When adjusting temperature set points,

use the following chart as a guide:

CONDITION: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Setting

1° higher

REFRIGERATOR too warm REFRIGERATOR Setting

1° lower

FREEZER too cold FREEZER Setting

1° higher

FREEZER too warm /

Too little ice

FREEZER Setting

1° lower

17

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is

turned off.

■ To turn cooling off, press and hold the LOCK and

MEASURED FILL buttons at the same time for 3 seconds.

The Cooling Off icon will blink seven times and then remain lit

as shown.

IMPORTANT:

■ To avoid unintentionally locking the dispenser or changing

other settings, press both buttons at exactly the same

time.

■ When cooling is off, the dispenser paddles and all

controls except Lock and Measured Fill are disabled.

■ Press and hold LOCK and MEASURED FILL for 3 seconds

again to turn cooling back on.

Options

Press the OPTIONS button to open the Options menu and select

between Fast Ice, Filter Status or Vacation mode.

Press the ICE/WATER button at any time to return to the Normal

screen.

Fast Ice

The Fast Ice feature assists with temporary periods of heavy ice

use by increasing ice production.

■ To turn on the Fast Ice feature, press the OPTIONS button to

access the Options menu, then press TEMP, under Fast Ice to

activate the feature. When the feature is on, the Fast Ice icon

will appear on the dispenser display screen. The Fast Ice

feature will remain on for 24 hours unless manually turned off.

■ To manually turn off the Fast Ice feature, press the OPTIONS

button to enter Options mode (unless you are already in

Options mode), then press TEMP, under Fast Ice, again.

When the feature has been turned off, the Fast Ice icon will

disappear from the dispenser display.

Filter Status

Displays the percentage of use remaining in the water filter (from

100% remaining to 0% remaining).

To access Filter Status, press the OPTIONS button to access the

Options menu, then press OPTIONS, under Filter Status, to

display the percent of life remaining in the water filter.

ALSO

The water filter status lights will let you know when to change

your water filter.

■ ORDER FILTER (Yellow) - Order a replacement water filter.

■ REPLACE FILTER (Red) - Replace the water filter. Replacing

the disposable water filter will automatically reset the water

filter status tracking feature. See “Water Filtration System.”

NOTE: REPLACE FILTER will remain illuminated if a filter is

not installed or installed incorrectly.

Vacation Mode

In Vacation Mode, the freezer will defrost less often to conserve

energy.

■ To turn on Vacation mode, press the OPTIONS button to

access the Options menu, then press LOCK, under Vacation,

to activate the feature. When the feature is on, the Vacation

icon will appear on the dispenser display screen as shown.

■ To turn off Vacation Mode, press the OPTIONS button to

access the Options menu, then press LOCK to turn off the

feature. The Vacation icon will disappear, and the screen will

display the settings as they were before Vacation Mode was

turned on.

NOTES:

■ During the first hour after Vacation Mode is turned on,

opening and closing the refrigerator door will not affect the

setting. After 1 hour has passed, opening and closing the

refrigerator door will turn off Vacation Mode.

■ While in Vacation Mode, if Fast Ice is turned on or the Door

Ajar alarm sounds, Vacation Mode will be canceled.

A. Press LOCK and MEASURED FILL at the same time.

18

Additional Features

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the

refrigerator door(s) or freezer drawer is open for 5 minutes and

cooling is turned on. The alarm will repeat every 2 minutes. Close

all doors and drawer to turn it off. The feature then is reset and

will reactivate when either door is left open again for 5 minutes.

■ NOTE: To mute the audible alarm while keeping the doors

open, such as while cleaning the inside of the refrigerator,

press any button on the control panel. The alarm sound will

be temporarily turned off, but the Door Ajar icon will still be

displayed on the dispenser control panel.

Disabling Sounds

■ To turn off control and dispenser sounds, press and hold ICE/

WATER and MEASURED FILL at the same time for

3 seconds. All normal operating tones are disabled. Only alert

tones will be audible.

■ To turn all sounds back on, press and hold ICE/WATER and

MEASURED FILL at the same time for 3 seconds again.

Showroom Mode

This mode is used only when the refrigerator is on display in a

retail store. If you unintentionally turn on Showroom mode, the

word “Showroom” will light up on the display. Exit Showroom

mode by pressing and holding LIGHT and LOCK at the same

time for 3 seconds.

Refrigerator Features

Temperature Controlled Exterior Drawer

IMPORTANT: This control sets the temperature for this drawer

only.

Use the full-width drawer to store large party platters or deli trays,

or use a drawer organizer to store smaller items such as yogurt,

juice boxes and lunch meat for easy access.

Temperatures have been preset for the storage of: Cold Drinks,

Meats/Cheeses, Assorted Items and Fruits/Vegetables. These

preset temperatures cannot be adjusted.

Press SELECT to toggle through the temperature settings. The

icon will illuminate when it is selected.

EasySlide Bin

A shallow storage compartment with glass lids which slide from

side to side is located below and in front of the crisper drawers.

NOTE: This compartment is not temperature or humidity

controlled, so it is not recommended for storing leafy vegetables.

To remove EasySlide bin:

1. Remove all three crisper drawers.

2. Hold the upper sliding lid near the trim and lift up to remove.

Remove the lower lid.

3. Grasp the front of the bin with both hands, and lift up on the

front to remove.

To replace EasySlide bin:

1. Slightly tilt the rear of the bin upward.

2. Align the center rib and tabs on the EasySlide bin with the

ribs and slots in the cabinet.

3. Lower the bin into place.

Crisper Drawers

To remove and replace the drawers:

1. Grasp the handle at the bottom of the drawer and slide the

drawer straight out to the stop. Lift the drawer off the bottom

guide.

2. Replace the drawer by placing it on the bottom drawer guide

and pushing it past the drawer stop into position.

To remove the crisper(s) cover:

1. Remove crisper drawers.

2. Holding the glass insert firmly with one hand, press up in

center of glass insert until it rises above the plastic frame.

Gently slide the glass insert forward to remove.

3. Lift the cover frame up and remove it.

To replace crisper(s) cover:

1. Fit back of cover frame into supports on side walls of the

refrigerator and lower the front of the cover frame into place.

2. Slide rear of glass insert into cover frame and lower front into

place.

3. Replace crisper drawers.

A. Crisper drawer handles

B. EasySlide bin

A

B

19

Water and Ice Dispensers

IMPORTANT:

■ Allow 3 hours for the refrigerator to cool down and chill water.

■ Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

■ The dispensing system will not operate when either the

refrigerator door or freezer drawer is open.

Flush the Water System

Air in the water dispensing system can cause the water dispenser

to drip. After connecting the refrigerator to a water source or

replacing the water filter, flush the water system.

Flushing the water dispensing system forces air from the water

line and filter and prepares the water filter for use. Additional

flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

1. Using a sturdy container, depress and hold the water

dispenser paddle for 5 seconds.

2. Release the dispenser paddle for 5 seconds. Repeat steps 1

and 2 until water begins to flow.

3. Once water begins to flow, continue depressing and releasing

the dispenser pad (5 seconds on, 5 seconds off) until a total

of 3 gal. (12 L) has been dispensed.

Calibrate Measured Fill

Household water pressure may affect the accuracy of the

Measured Fill feature. So, for optimum performance of your water

dispenser, you must first calibrate Measured Fill.

IMPORTANT:

■ Flush the water system before calibrating Measured Fill.

■ For best results, calibration should be performed when water

is not being used in the house.

1. Place a sturdy measuring cup (1 cup [237 mL] size) on the

dispenser tray centered in front of the ice/water dispenser

paddle.

NOTE: Depending on your model, a measuring cup may be

provided.

2. Press and hold the OPTIONS and LOCK buttons at the same

time for 3 seconds. The words “Back” and “1 Cup” will

appear on the display screen. Also, the Calibrate Measured

Fill icon will illuminate and remain lit while the Measured Fill

feature is being calibrated.

NOTE: You may press ICE/WATER “Back” at any time to exit

calibration mode. The Calibrate Measured Fill icon will

disappear.

3. Press and release the ice/water dispenser paddle, as needed,

to dispense water to the 1 cup fill line.

NOTE: If overfilling or spilling occurs, discard the water and

press ICE/WATER “Back” to restart the calibration process.

A. Ice/Water dispenser paddle

B. Measuring cup (1 cup)

A

B

20

4. When 1 cup of water has been correctly dispensed into the

measuring cup, press the MEASURED FILL button under the

word “Confirm” to confirm the calibration.

5. When Measured Fill calibration has been confirmed the icons

will disappear and the display will return to the home screen.

Dispensing

Press ICE/WATER to toggle through the following choices in a

continuous loop:

■ Water (default) - Dispenses water

■ Cubed - Dispenses cubed ice.

■ Crushed - Dispenses crushed ice

NOTES:

■ The word “ICE” appears on the display screen when

either crushed or cubed ice is selected.

■ For crushed ice, cubes are crushed before being

dispensed. This may cause a slight delay when

dispensing crushed ice. Noise from the ice crusher is

normal, and pieces of ice may vary in size.

■ When changing from crushed to cubed, a few ounces of

crushed ice will be dispensed along with the first cubes.

The Water Dispenser

IMPORTANT:

■ Dispense at least 1 qt (1 L) of water every week to maintain a

fresh supply.

■ If the flow of water from the dispenser decreases, it could be

caused by low water pressure.

■ With the water filter removed, dispense 1 cup (237 mL) of

water. If 1 cup (237 mL) of water is dispensed in

8 seconds or less, the water pressure to the refrigerator

meets the minimum requirement.

■ If it takes longer than 8 seconds to dispense 1 cup

(237 mL) of water, the water pressure to the refrigerator is

lower than recommended. See “Water Supply

Requirements” and “Troubleshooting” for suggestions.

To Dispense Water (Standard):

1. Select water.

2. Press a sturdy glass against the dispenser paddle.

NOTE: While dispensing water and for 3 seconds after

dispensing has stopped, the digital display will show how

much water has been dispensed.

3. Remove the glass to stop dispensing.

To Dispense Water (Measured Fill):

Measured Fill allows you to dispense a specified amount of water

with the touch of a few controls.

NOTE: The amount of water you select will be dispensed. Be

sure that the container is empty and can hold the entire volume. If

ice is in the container, you may need to adjust your selection.

1. Press MEASURED FILL to turn on the feature. When the

feature is on, the Measured Fill screen appears on the display.

NOTES:

■ The dispenser will automatically turn off Measured Fill

after 1 minute of inactivity. When Measured Fill is turned

off, any changes you have made will be lost and all

defaults will be restored.

■ Press ICE/WATER “Back,” to manually turn off the

Measured Fill feature.

2. Press LIGHT, under Units, to toggle among ounce, cup and

liter. The default unit is ounce.

Default, minimum, and maximum volumes are listed below.

3. Press LOCK or OPTIONS to adjust the water volume as

desired. The LOCK control increases the volume, and the

OPTIONS control lowers the volume.

NOTES:

■ When increasing or decreasing the dispense volumes, if

an adjustment button (-/+) is held for approximately

10 seconds or longer the control may stop responding.

Release the button for approximately 2 seconds and then

continue making the adjustment.

■ Most coffee cups (commonly 4 to 6 oz [118 to 177 mL]

per cup) are not the same size as a measuring cup (8 oz

[237 mL]). You may need to adjust the volume to avoid

unintentionally overfilling coffee cups.

A. 1 cup of water

Water Crushed Cubed

A

Units Default Minimum Maximum

Ounces 8 1 128

Cups 1 ¹/₄ 16

Liters 0.25 0.05 4.00

La page charge ...

Whirlpool WRX986SIHV Manuel utilisateur

Whirlpool WRX986SIHV Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents