Kenmore 70372 Guide d'installation

Dryer Installation Instructions

Instrucciones de instalación de la secadora

Instructions d’installation de la sécheuse

English / Español / Français

Table of Contents...2 / Índice...24 / Table des matières...46

Kenmore®

Gas & Electric Dryer

Secadora a gas y eléctrica

Sécheuse à gaz et électrique

P/N W11040140A

Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

www.sears.ca

2

DRYER SAFETY

DRYER SAFETY .................................................................. 2

INSTALLATION REQUIREMENTS .......................................4

Tools and Parts ............................................................4

LOCATION REQUIREMENTS ..............................................5

ELECTRICAL REQUIREMENTS – U.S.A. ONLY ....................6

ELECTRIC DRYER POWER HOOKUP – CANADA ONLY .....7

GAS DRYER POWER HOOKUP – U.S.A. AND CANADA ....7

INSTALL LEVELING LEGS...................................................9

MAKE ELECTRICAL CONNECTION – U.S.A. ONLY .......... 10

MAKE GAS CONNECTION – U.S.A. AND CANADA ........ 16

VENTING ........................................................................ 16

Venting Requirements ............................................... 16

Plan Vent System ......................................................17

Install Vent System .....................................................18

CONNECT VENT ............................................................. 19

LEVEL DRYER .................................................................. 19

COMPLETE INSTALLATION CHECKLIST ...........................20

REVERSE DOOR SWING (OPTIONAL) ..............................21

TROUBLESHOOTING .......................................................23

ASSISTANCE OR SERVICE ................................. Back Cover

TABLE OF CONTENTS

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by

the State of Massachusetts.

■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.

■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).

INSTALLATION NOTES

Date of purchase: _________________________________

Date of installation: _______________________________

Installer: ________________________________________

Model number: ___________________________________

Serial number: ___________________________________

3

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, Part 1, CSA C22.1.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property

damage.

Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this

or any other appliance.

–

WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call the re department.

–

Installation and service must be performed by a qualied installer, service agency, or

the gas supplier.

•

Clear the room, building, or area of all occupants.

4

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed for all installations:

Level

#2 Phillips screwdriver Wire stripper (direct wire

installations)

Parts supplied:

Flat-head screwdriver

Adjustable wrench that

opens to 1" (25 mm) or

hex-head socket wrench

Tin snips (new vent

installations)

Caulking gun and compound

(for installing new exhaust

vent)

Vent clamps

1/4" (6 mm) and

5/16" (8 mm) nut driver

(recommended)

Tools needed for gas installations:

8" (203 mm) or 10"

(254 mm) pipe wrench

8" (203 mm) or 10"

(254 mm) adjustable wrench

(for gas connections)

Pipe-joint compound

resistant to propane gas

Plastic putty knife

INSTALLATION REQUIREMENTS

Leveling legs (4)

Tape measure Pliers

If using a power supply cord:

Use a UL Listed power supply cord kit marked for use

with clothes dryers. The kit should contain:

■ A UL Listed 30-amp power supply cord, rated 120-/240-volt

minimum, and have a temperature rating of 140ºF (60ºC)

minimum. The cord should be type SRD or SRDT and be

at least 4 ft. (1.22 m) long. The wires that connect to

the dryer must end in ring terminals or spade terminals

with upturned ends.

■ A UL Listed strain relief.

Parts package is located in dryer drum. Check that all parts

are included.

5

Parts needed (not supplied with dryer):

Check local codes. Check existing electrical supply and venting.

See “Electrical Requirements” and “Venting Requirements” before

purchasing parts.

Mobile home installations require metal exhaust system hardware

available for purchase from the dealer from whom you purchased

your dryer. For further information, please refer to the “Assistance

or Service” section in your Use and Care Guide.

LOCATION REQUIREMENTS

You will need:

■ A location allowing for proper exhaust installation.

See “Venting Requirements.”

■ A separate 15- or 20-amp circuit needed for gas dryers

and 30-amp circuit needed for electric dryers.

■ If using power supply cord, a grounded electrical outlet

located within 2 ft. (610 mm) of either side of dryer.

See “Electrical Requirements.”

■ Floor must support dryer weight of 200 lbs. (90.7 kg).

Also consider weight of companion appliance.

■ Level oor with maximum slope of 1" (25 mm) under entire

dryer. If slope is greater than 1" (25 mm), clothes may not

tumble properly and automatic sensor cycles may not operate

correctly.

■ For garage installation, place dryer at least 18" (460 mm)

above oor.

IMPORTANT: Do not operate, install, or store dryer where

it will be exposed to water, weather, or at temperatures below

45°F (7°C). Lower temperatures may cause dryer not to

shut o at end of automatic sensor cycles, resulting in longer

drying times.

NOTE: No other fuel-burning appliance can be installed in the

same closet as a dryer.

DRYER DIMENSIONS

INSTALLATION CLEARANCES

For each arrangement, consider allowing more space for ease of

installation and servicing, spacing for companion appliances, and

clearances for walls, doors, and floor moldings. Space must be

large enough to allow door to fully open. Add spacing on all sides

of dryer to reduce noise transfer. If a closet door or louvered door

is installed, top and bottom air openings in door are required.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quarters. Contact your local building inspector.

NOTE: Most installations require a minimum of 6" (152 mm)

clearance behind dryer for exhaust vent with elbow. See

“Venting Requirements.”

Front view:

Side view, hamper doorSide view, side-swing door

Spacing for recessed area or closet installation

The dimensions shown are for the minimum spacing allowed.

■ Additional spacing should be considered for ease of installation

and servicing.

■ Additional clearances might be required for wall, door, and

oor moldings.

■ Additional spacing of 1" (25 mm) on all sides of the dryer is

recommended to reduce noise transfer.

■ For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilitation openings are

acceptable.

■ Companion appliance spacing should also be considered.

53"

(1341 mm)

30"

(762 mm)

43

1

/4"

(1096 mm)

30"

(762 mm)

27"

(685 mm)

1

/4"

(32 mm)

40

1

/2"

(1027 mm)

6

Mobile home – Additional installation requirements:

This dryer is suitable for mobile home installations. The installation

must conform to the Manufactured Home Construction and Safety

Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard

for Mobile home construction and Safety, Title 24, HUD Part 280)

or Standard CAN/CSA-Z240 MH.

Mobile home installations require:

All dryers:

■ Metal exhaust system hardware, available for purchase

from your dealer. For further information, see “Assistance

or Service” section in your Use and Care Guide.

■ Special provisions must be made in mobile homes to

introduce outside air into dryer. Openings (such as a

nearby window) should be at least twice as large as

dryer exhaust opening.

For gas dryer mobile home installations:

■ Mobile Home Installation Hold-down Kit Part Number

346764 is available to order. For further information,

see “Assistance or Service” section in your Use and

Care Guide.

Recommended/Minimum spacing

ELECTRICAL REQUIREMENTS –

U.S.A. ONLY (SPÉCIFICATIONS

ÉLECTRIQUES – ÉTATS-UNIS

SEULEMENT)

It is your responsibility:

■ To contact a qualied electrical installer.

■ To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70 – latest edition and all local codes and ordinances.

The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

If using a power supply cord:

Use a UL Listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

■ A UL Listed 30-amp power supply cord, rated 120-/240-volt

minimum, and have a temperature rating of 140ºF (60ºC)

minimum. The cord should be type SRD or SRDT and be at least

4 ft. (1.22 m) long. The wires that connect to the dryer must end

in ring terminals or spade terminals with upturned ends.

■ A UL Listed strain relief.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

■ This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor

is permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical

supply connection, the neutral ground conductor must be

removed from the external ground connector (green screw),

and secured under the neutral terminal (center or white wire)

of the terminal block. When the neutral ground conductor is

secured under the neutral terminal (center or white wire) of the

terminal block, the dryer cabinet is isolated from the neutral

conductor.

■ If local codes do not permit the connection of a neutral

ground wire to the neutral wire, see “Optional 3-Wire

Connection” section.

■ A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas

where local codes prohibit grounding through the neutral

conductors.

4-wire

receptacle

(14-30R)

If your outlet looks like this:

Then choose a 4-wire power supply cord with

ring or spade terminals and UL Listed strain

relief. The 4-wire power supply cord, at least

4 ft. (1.22 m) long, must have four 10-gauge

solid copper wires and match a 4-wire

receptacle of NEMA Type 14-30R. The ground

wire (ground conductor) may be either green or

bare. The neutral conductor must be identied

by a white cover.

3-wire

receptacle

(10-30R)

If your outlet looks like this:

Then choose a 3-wire power supply cord with

ring or spade terminals and UL Listed strain

relief. The 3-wire power supply cord, at least

4 ft. (1.22 m) long, must have three 10-gauge

solid copper wires and match a 3-wire

receptacle of NEMA Type 10-30R.

■ To supply the required 3- or 4-wire, single phase, 120-/240-

volt, 60 Hz, AC-only electrical supply (or 3- or 4-wire, 120-/

208-volt electrical supply, if specied on the serial/rating

plate) on a separate 30-amp circuit, fused on both sides

of the line. Connect to an individual branch circuit. Do not

have a fuse in the neutral or grounding circuit.

■ Do not use an extension cord.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

6"/0"

(152 mm/0 mm)

14" max

(356 mm)

1"/0"

(25 mm/0 mm)

1"/1"

(25 mm)

18"/18"*

(457 mm)

3"/3"

(76 mm)

3"/3"

(76 mm)

48"

2

/48"

2

(310 cm

2

)

24"

2/

24"

2

(155 cm

2

)

7

4-wire receptacle

(14-30R)

ELECTRIC DRYER POWER

HOOKUP – CANADA ONLY

ELECTRICAL REQUIREMENTS

It is your responsibility:

■ To contact a qualied electrical installer.

■ To be sure that the electrical connection is adequate and

in conformance with Canadian Electrical Code, C22.1 – latest

edition and all local codes. A copy of above codes standard

may be obtained from: Canadian Standards Association,

178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

■ To supply the required 4-wire, single phase, 120-/240-volt,

60 Hz, AC-only electrical supply on a separate 30-amp circuit,

fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch

circuit.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

■ Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), covered with exible metallic conduit. All

current-carrying wires must be insulated.

■ 10-gauge solid copper wire (do not use aluminum) at least

5 ft. (1.52 m) long.

■ This dryer is equipped with a UL Listed

and/or CSA International Certied Power

Cord intended to be plugged into a

standard 14-30R wall receptacle. The cord

is 5 ft. (1.52 m) long. Be sure wall receptacle

is within reach of dryer’s nal location.

For further information, please reference service numbers located

in “Assistance or Service” section of your Use and Care Guide.

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a qualied electrician.

GAS DRYER POWER HOOKUP –

U.S.A. AND CANADA

ELECTRICAL REQUIREMENTS

■ 120-volt, 60 Hz, AC-only, 15- or 20-amp fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is also recommended that a separate circuit

serving only this dryer be provided.

8

GAS TYPE

Natural Gas:

This dryer is equipped for use with natural gas. It is certied

by UL for use with propane gas with appropriate conversion.

■ Your dryer must have the correct burner for the type of gas in

your home. Burner information is located on the rating plate in

the door well of your dryer. If this information does not agree

with the type of gas available, contact your dealer or call the

phone numbers referenced in the “Assistance or Service” section

of your Use and Care Guide.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 13" (330 mm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

GAS SUPPLY REQUIREMENTS

Propane Gas Conversion:

IMPORTANT: Conversion must be made by a qualied technician.

No attempt shall be made to convert the dryer from the gas

specied on the model/serial rating plate for use with a dierent

gas without consulting your gas company.

GAS SUPPLY LINE

Option 1 (Recommended Method)

Flexible stainless steel gas connector:

■ If local codes permit, use a new exible stainless steel gas

connector (Design Certied by the American Gas Association

or CSA International) to connect your dryer to the rigid gas

supply line. Use an elbow and a 3/8" are x 3/8" NPT adapter

tting between the stainless steel gas connector and the dryer

gas pipe, as needed to prevent kinking.

Option 2 (Alternate Method)

Approved aluminum or copper tubing

■ Must include 1/8" NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas

connection to the dryer.

■ 1/2" IPS pipe is recommended.

■ 3/8" approved aluminum or copper tubing is acceptable

for lengths under 20 ft. (6.1 m) if local codes and gas

supplier permit.

■ If you are using natural gas, do not use copper tubing.

■ Lengths over 20 ft. (6.1 m) should use larger tubing and

a dierent size adapter tting.

■ If your dryer has been converted to use propane gas,

3/8” propane compatible copper tubing can be used.

If the total length of the supply line is more than 20 ft.

(6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of

propane gas must be used. Do not use TEFLON

®†

tape.

■ Must include shut-o valve.

In the U.S.A.:

An individual manual shut-o valve must be installed within

6 ft. (1.8 m) of the dryer in accordance with the National Fuel

Gas Code, ANSI Z223.1. The location should be easy to reach

for opening and closing.

In Canada:

An individual manual shut-o valve must be installed in

accordance with the B149.1, Natural Gas and Propane

Installation Code. It is recommended that an individual manual

shuto valve be installed within 6 ft. (1.8 m) of the dryer. The

location should be easy to reach for opening and closing.

E

BA

D

C

†

®

TEFLON is a registered trademark of Chemours.

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a qualied electrician.

A. 3/8" exible gas connector

B. 3/8" pipe to are adapter tting

C. 1/8" NPT minimum plugged tapping

D. 1/2" NPT gas supply line

E. Gas shuto valve

9

3/8" NPT dryer pipe

NOTE: For a garage installation, the gas pipe height must be

an additional 18" (460 mm) from the  oor.

GAS SUPPLY CONNECTION REQUIREMENTS

■ Use an elbow and a 3/8"  are x 3/8" NPT adapter  tting

between the  exible gas connector and the dryer gas pipe,

as needed to avoid kinking.

■ Use only pipe-joint compound. Do not use TEFLON

®

tape.

■ This dryer must be connected to the gas supply line with a

listed  exible gas connector that complies with the standard

for connectors for gas appliances, ANSI Z21.24 or CSA 6.10.

BURNER INPUT REQUIREMENTS

Elevations above 2,000 ft. (610 m):

■ When installed above 2,000 ft. (610 m), a 4% reduction of the

burner Btu rating shown on the model/serial number plate is

required for each 1,000 ft. (305 m) increase in elevation.

Gas supply pressure testing

■ The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than 1/2 psi.

DRYER GAS PIPE

■ The gas pipe that comes out through the rear of your dryer

has a 3/8" male pipe thread.

INSTALL LEVELING LEGS

1. Prepare dryer for leveling legs

Firmly grasp dryer body (not console panel) and gently lay

dryer down on back cardboard corner posts.

IMPORTANT: If laying dryer on its back, use the cardboard

corner posts the dryer was packed with to avoid damaging

the back of the dryer.

2. Screw in leveling legs

Using a wrench and tape measure, screw leveling legs into leg

holes until bottom of foot is approximately 1" (25 mm) from

bottom of dryer.

Now stand the dryer on its feet. Slide the dryer until it is

close to its  nal location. Leave enough room to connect the

exhaust vent.

For mobile home use

Gas dryers must be securely fastened to the  oor.

Mobile home installations require a Mobile Home Installation

Hold-down Kit (Part Number 346764). For ordering

information, please reference “Assistance or Service” section

in the Use and Care Guide.

1

/2"

(38 mm)

5

3

/4"

(146 mm)

10

MAKE ELECTRICAL CONNECTION – U.S.A. ONLY (EFFECTUER LE

RACCORDEMENT ÉLECTRIQUE – ÉTATS-UNIS SEULEMENT)

Electrical Connection Options

1. Choose electrical connection type

Power supply cord 4-wire receptacle

(NEMA Type 14-30R):

Go to “Power Supply Cord Connection.”

3-wire direct connection:

Go to “Direct Wire Connection.”

4-wire direct connection:

Go to “Direct Wire Connection.”

Power supply cord 3-wire receptacle

(NEMA Type 10-30R):

Go to “Power Supply Cord Connection.”

NOTE: If local codes do not permit connection of a

cabinet-ground conductor to neutral wire, go to “Optional

3-Wire Connection.” This connection may be used with

either a power supply cord or a direct wire connection.

2. Remove terminal block cover

Remove hold-down screws and terminal block cover.

1. Attach power supply cord strain relief

Remove the screws from a 3/4" (19 mm) UL Listed strain relief.

Put the tabs of the two clamp sections (C) into the hole below

the terminal block opening (B) so that one tab is pointing

diagonally toward the dryer (A) and the other is pointing

diagonally away from the dryer (D), and hold in place.

Tighten strain relief screws just enough to hold the two

clamp sections (C) together.

Power Supply Cord Strain Relief

POWER SUPPLY CORD CONNECTION

Before you start: disconnect power.

A

B

C

D

11

Put power supply cord through the strain relief. Be sure that

the wire insulation on the power supply cord is inside the strain

relief. The strain relief should have a tight  t with the dryer

cabinet and be in a vertical position. Do not further tighten

strain relief screws at this point.

2. Attach power supply cord to strain relief

4-Wire Power Supply Cord Connection

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire connections.

Power supply cord 4-wire receptacle

(NEMA Type 14-30R):

Go to “4-Wire Power Supply Cord

Connection.”

Power supply cord 3-wire receptacle

(NEMA Type 10-30R):

Go to “3-Wire Power Supply Cord

Connection.”

If your outlet looks like this:

4-wire receptacle

(NEMA type 14-30R)

4-prong plug

Spade terminals

with upturned ends

Ring terminals

Remove center terminal block screw (B). Remove neutral ground

wire (E) from external ground conductor screw (A).

1. Prepare to connect neutral

ground wire and neutral wire

2. Connect neutral ground wire

and neutral wire

Connect neutral ground wire (E) and neutral wire (white) (C)

of power supply cord under center terminal block screw (B).

Tighten screw.

Connect ground wire (F) (green or bare) of power supply cord

to external ground conductor screw (A). Tighten screw.

3. Connect ground wire

B

A

E

B

E

C

F

A

12

3-wire receptacle

(NEMA type 10-30R)

3-prong plug

Spade terminals

with upturned ends

Ring terminals

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

3-Wire Power Supply Cord Connection

3. Connect remaining wires

Connect remaining wires to outer terminal block screws. Tighten

screws. Finally, reinsert tabs of terminal block cover into slots of

dryer rear panel. Secure cover with hold-down screws. Now, go

to “Venting Requirements.”

2. Connect neutral wire

Connect neutral wire (white or center) (C) of power supply cord

to center terminal block screw (B). Tighten screw.

Remove center terminal block screw (B).

1. Remove center screw

4. Connect remaining wires

Connect remaining wires to outer terminal block screws.

Tighten screws. Finally, reinsert tabs of terminal block cover

into slots of dryer rear panel. Secure cover with hold-down

screws. Now, go to “Venting Requirements.”

B

C

13

DIRECT WIRE CONNECTION

Unscrew the removable conduit connector (A) and any

screws from a 3/4" (19 mm) UL Listed strain relief. Put the

threaded section of the strain relief (C) through the hole below

the terminal block opening (B). Reaching inside the terminal

block opening, screw the removable conduit connector (A)

onto the strain relief threads.

1. Attach direct wire strain relief

Direct Wire Strain Relief

Put direct wire cable through the strain relief. The strain relief

should have a tight  t with the dryer cabinet and be in a

vertical position. Tighten strain relief screw against the direct

wire cable.

2. Attach direct wire cable to strain relief

3-wire direct connection:

Go to “3-Wire Direct Connection.”

4-wire direct connection:

Go to “4-Wire Direct Connection”

on this page.

If your wiring looks like this:

4-Wire Direct Wire Connection

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit 3-wire connections.

Direct wire cable must have 5 ft. (1.52 m) of extra length so

dryer may be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable,

leaving bare ground wire at 5" (127 mm). Cut 1½" (38 mm)

from remaining three wires. Strip insulation back 1" (25 mm).

Shape ends of wires into hooks.

1"

(25 mm)

5"

(127 mm)

1. Prepare your 4-wire cable

for direct connection

Fire Hazard

Use 10 gauge copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected

to green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, re, or

electrical shock.

A

B

C

14

4. Connect ground wire

Connect ground wire (green or bare) (F) of direct wire cable

to external ground conductor screw (A). Tighten screw.

Place hooked ends of remaining direct wire cable wires

under outer terminal block screws (hooks facing right).

Squeeze hooked ends together and tighten screws. Finally,

reinsert tabs of terminal block cover into slots of dryer rear

panel. Secure cover with hold-down screws. Now, go to

“Venting Requirements.”

5. Connect remaining wires

3-Wire Direct Wire Connection

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

2. Remove center screw

Remove center terminal block screw (B).

Direct wire cable must have 5 ft. (1.52 m) of extra length so

dryer may be moved if needed.

Strip 3½" (89 mm) of outer covering from end of cable. Strip

insulation back 1" (25 mm). If using 3-wire cable with ground

wire, cut bare wire even with outer covering. Shape wire ends

into hooks.

1"

(25 mm)

3½"

(89 mm)

1. Prepare your 3-wire cable

for direct connection

3. Connect neutral ground wire

and neutral wire

Connect neutral ground wire (E) and place

hooked end (hook facing right) of neutral

wire (white or center wire) (C) of direct wire

cable under center screw of terminal block

(B). Squeeze hooked ends together and

tighten screw.

2. Prepare to connect neutral

ground wire and neutral wire

Remove center terminal block screw (B). Remove neutral

ground wire (E) from external ground conductor screw (A).

B

E

A

B

E

C

A

F

B

15

4. Connect remaining wires

Place hooked ends of remaining direct wire cable wires

under outer terminal block screws (hooks facing right).

Squeeze hooked ends together and tighten screws. Finally,

reinsert tabs of terminal block cover into slots of dryer rear

panel. Secure cover with hold-down screws. Now, go to

“Venting Requirements.”

Place hooked end of neutral wire (white

or center) (C) of direct wire cable under

center terminal block screw (B). Squeeze

hooked end together. Tighten screw.

3. Connect neutral wire

1. Prepare to connect neutral

ground wire and neutral wire

Remove center terminal block screw (B). Remove neutral ground

wire (E) from external ground conductor screw (A).

Optional 3-Wire Connection

You must verify with a qualified electrician that this

grounding method is acceptable before connecting.

2. Connect neutral ground wire

and neutral wire

Connect neutral ground wire (E) and neutral wire (white or

center wire) (C) of power supply cord or cable under center

terminal block screw (B). Tighten screw.

3. Connect remaining wires

Connect remaining wires to outer terminal block screws.

Tighten screws.

4. Connect external ground wire

Connect a separate copper ground wire (G) from the external

ground conductor screw (A) to an adequate ground. Finally,

reinsert tabs of terminal block cover into slots of dryer rear

panel. Secure cover with hold-down screws. Now, go to

“Venting Requirements.”

B

C

B

A

E

B

E

C

A

G

16

Venting Requirements

WARNING: To reduce the risk of  re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent, chimney,

wall, ceiling, attic, crawlspace, or a concealed space of a

building. Only rigid or  exible metal vent shall be used for

exhausting.

4"

(102 mm)

4" (102 mm) heavy metal exhaust vent

■ Only a 4" (102 mm) heavy metal exhaust vent and clamps

may be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in  nal dryer location.

■ Remove excess to avoid sagging and kinking that may

result in reduced air ow and poor performance.

■ Do not install in enclosed walls, ceilings, or  oors.

■ The total length should not exceed 7¾ ft. (2.4 m).

■ The length of  exible metal vent used must be included

in the overall vent system design as shown in the Vent

System Chart.

NOTE: If using an existing vent system, clean lint from entire length

of the system and make sure exhaust hood is not plugged with

lint. Replace plastic or metal foil vents with rigid metal or  exible

metal vents. Review Vent System Chart, and if necessary, modify

existing vent system to achieve best drying performance.

VENTING

1. Connect gas supply to dryer

Remove red cap from gas pipe. Using a wrench to tighten,

connect gas supply to dryer. Use pipe-joint compound

on threads of all non- ared male  ttings. If  exible metal

tubing is used, be sure there are no kinks.

NOTE: For propane gas connections, you must use pipe-joint

compound resistant to action of propane gas. Do not use

TEFLON

®

tape.

A

B

Non- ared

male  tting

Flared

male  tting

3. Openshut-oﬀvalve

Open shut-o valve in supply line; valve is open when handle

is parallel to gas pipe. Then, test all connections by brushing

on an approved noncorrosive leak-detection solution. Bubbles

will show a leak. Correct any leaks found.

A

B

Open valve

Closed valve

B

A

D

C

2. Planpipettingconnection

A combination of pipe  ttings must be used to connect dryer

to existing gas line. A recommended connection is shown. Your

connection may be di erent, according to supply line type,

size, and location.

A. 3/8"  exible gas connector

B. 3/8" dryer pipe

C. 3/8" to 3/8" pipe elbow

D. 3/8" pipe-to- are adapter  tting

MAKE GAS CONNECTION –

U.S.A. AND CANADA

17

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct

and catch lint. Do not use duct tape.

Vent products can be purchased from your dealer. For more

information, see “Assistance or Service” section in your Use and

Care Guide.

Louvered Hood

Good

Angled Hood

Box Hood

Better

Exhaust hoods:

Elbows:

Recommended Styles:

■ 45° elbows provide better airow than 90° elbows.

■ Must be at least 12" (305 mm) from ground or any object

that may obstruct exhaust (such as owers, rocks, bushes,

or snow).

Acceptable Style:

Optional exhaust installations:

Plan Vent System

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

E. Clamps

F. Rigid metal or exible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

I. Optional side exhaust outlet

If you prefer, dryer may be converted to exhaust through the

bottom and sides. You must contact your local dealer to have

dryer converted.

A

C

A. Standard rear oset exhaust installation

B. Left- or right-side exhaust installation

C. Bottom exhaust installation

B

C

D

E

F

G

H

A

I

18

Special provisions for mobile homes:

Exhaust vent must be securely fastened to a noncombustible

portion of mobile home and must not terminate beneath the

mobile home. Terminate exhaust vent outside.

Mobile Home Exhaust Installation

2. Connect vent to exhaust hood

Vent must  t over the exhaust hood. Secure vent to exhaust

hood with 4" (102 mm) clamp. Run vent to dryer location using

straightest path possible. Avoid 90° turns. Use clamps to seal

all joints. Do not use duct tape, screws, or other fastening

devices that extend into interior of vent to secure vent,

because they can catch lint.

Install Vent System

12" min.

(305 mm)

12" min.

(305 mm)

1. Install exhaust hood

Install exhaust hood and use caulking compound to seal

exterior wall opening around exhaust hood.

Determine vent length and elbows needed for best drying

performance:

■ Use following Vent System Chart to determine type of

vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those speci ed

in Vent System Chart. Exhaust systems longer than those

speci ed will:

■ Shorten life of dryer.

■ Reduce performance, resulting in longer drying times

and increased energy usage.

The Vent System Chart provides venting requirements

that will help achieve best drying performance.

NOTE: Bottom exhaust installations have a 90° turn inside

the dryer. To determine maximum exhaust length, add one

90° turn to the chart.

Determine vent path:

■ Select route that will provide straightest and most direct

path outdoors.

■ Plan installation to use fewest number of elbows and turns.

■ When using elbows or making turns, allow as much room

as possible.

■ Bend vent gradually to avoid kinking.

■ Use as few 90° turns as possible.

Vent System Chart

Number of

90° turns

or elbows

Type

of vent

Box/louvered

hoods

Angled

hoods

1

4

3

2

0 Rigid metal

Rigid metal

64 ft. (20 m)

54 ft. (16.5 m)

44 ft. (13.4 m)

35 ft. (10.7 m)

27 ft. (8.2 m)

58 ft. (17.7 m)

48 ft. (14.6 m)

38 ft. (11.6 m)

29 ft. (8.8 m)

21 ft. (6.4 m)

19

LEVEL DRYER

Not Level LEVEL Not Level

Check levelness of dryer from side to side. Repeat from

front to back.

NOTE: The dryer must be level for the moisture sensing

system to operate correctly.

CONNECT VENT

1. Connect vent to exhaust outlet

Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer. If connecting to existing vent, make sure vent is

clean. Dryer vent must  t over dryer exhaust outlet and inside

exhaust hood. Check that vent is secured to exhaust hood

with a 4" (102 mm) clamp.

2. Movedryertonallocation

Move dryer to  nal location. Avoid crushing or kinking vent.

1. Level dryer

2. Adjust leveling legs

If dryer is not level, prop up using a wood block. Use wrench

to adjust legs up or down, and check again for levelness.

Place

level here

Place

level here

20

COMPLETE INSTALLATION

CHECKLIST

■ Check that all parts are now installed. If there is an extra

part, go back through steps to see what was skipped.

■ Check that you have all of your tools.

■ Dispose of/recycle all packaging materials.

■ Check dryer’s nal location. Be sure vent is not crushed

or kinked.

■ Check that dryer is level. See “Level Dryer.”

■ Remove lm on console and any tape remaining on dryer.

■ Wipe dryer drum interior thoroughly with a damp cloth

to remove any dust.

■ Read “Dryer Use” in your Use and Care Guide.

Electric Models:

■ For power supply cord installation, plug into a grounded

outlet. For direct wire installation, turn on power.

Gas Models:

■ Check that gas supply is on.

■ Check for leaks.

All Models:

■ Select a Timed Dry heated cycle and start dryer.

Do not select Air Only temperature setting.

If dryer will not start, check the following:

• Controls are set in a running or On position.

• Start button has been pushed rmly (held for 3 seconds).

• Dryer is plugged into an outlet and/or electrical supply

is connected.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

This dryer automatically runs an installation diagnostic routine

at the start of its rst cycle.

If you receive an L2 code, there may be a problem with your

home power supply keeping the dryer’s heater from turning on.

See “Troubleshooting.”

If your airow screen reads “Check Vent,” your dryer vent may

be crushed or blocked. See “Troubleshooting.”

NOTE: You may notice an odor when dryer is rst heated. This

odor is common when heating element is rst used. The odor will

go away.

La page charge ...

Kenmore 70372 Guide d'installation

Ce manuel convient également à

Kenmore 70372 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents