Samsung DVD-H1080R Manuel utilisateur

imagine the possibilities

Thanks you for purchasing this Samsung product.

To receive more complete service, please register

your product at

www.samsung.com/global/register

DVD Player

user manual

DVD-H1080

DVD-H1080R

DVD-H1080W

AK68-01754Q(03)

precautions

2_ precautions

1. Setting up

- Refer to the identification label located

on the rear of your player for its proper

operating voltage.

- Install your player in a cabinet with

adequate ventilation holes. (7~10cm) Do

not block ventilation holes on any of the

components for air circulation.

- Do not push the disc tray in by hand.

- Do not stack components.

- Be sure to turn all components off before

moving the player.

- Before connecting other components to this

player, be sure to turn them off.

- Be sure to remove the disc and turn off the

player after use, especially if you are not

going to use it for a long time.

- The mains plug is used as a disconnect

device and shall stay readily operable at

any time.

2. For your safety

- This product utilizes a laser. Use of

controls or adjustments or performance of

procedures other than those specified

herein may result in hazardous radiation

exposure.

- Do not open covers and do not repair

yourself. Refer servicing to qualified

personal.

3. Caution

- Your player is not intended for industrial

use but for domestic purposes. Use of this

product is for personal use only.

-

Apparatus shall not be exposed to dripping

or

splashing and no objects filled with liquids

,

such as vases, should be placed on the

apparatus.

- Exterior influences such as lightning and

static electricity can affect normal operation

of this player. If this occurs, turn the player

off and on again with the POWER button,

or disconnect and then reconnect the AC

power cord to the AC power outlet. The

player will operate normally.

- When condensation forms inside

the player due to sharp changes in

temperature, the player may not operate

correctly. If this occurs, leave the player

at room temperature until the inside of the

player becomes dry and operational.

4. Disc

- Do not clean disc using record-cleaning

sprays, benzene, thinner, or other volatile

solvents that may cause damage to the disc

surface.

- Do not touch the disc’s signal surface. Hold

by the edges or by one edge and the hole

in the center.

- Wipe the dirt away gently; never wipe a

cloth back and forth over the disc.

5. Environmental info

- The battery used in this product contains

chemicals that are harmful to the environ

ment.

- So, dispose of batteries in the proper man

ner, according to federal, state, and local

regulations.

The product unit accompanying this user manual

is licensed under certain intellectual property rights

of certain third parties. This license is limited to

private non-commercial use by end-user consum

-

ers for licensed contents. No rights are granted for

commercial use. The license does not cover any

product unit other than this product unit and the

license does not extend to any unlicensed product

unit or process conforming to ISO/OUR 11172-3 or

ISO/OUR 13818-3 used or sold in combination with

this product unit. The license only covers the use of

this product unit to encode and/or decode audio files

conforming to the ISO/OUR 11172-3 or ISO/OUR

13818-3. No rights are granted under this license for

product features or functions that do not conform to

the ISO/OUR 11172-3 or ISO/OUR 13818-3.

CAUTION: USE OF ANY CONTROLS,

ADJUSTMENTS, OR PROCEDURES OTHER

THAN SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

English _3

before you

start

table of

content

Remote Control

User’s Manual

Video/Audio

Cable

Install Batteries in the Remote con-

trol

If remote control doesn’t operate

properly:

- Check the polarity + - of the battery (Dry-Cell)

- Check if the battery is drained.

- Check if remote control sensor is blocked by

obstacles.

- Check if there is any fluorescent lighting nearby.

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Type and Characteristics . . . . . . . . . . . . . . . .5

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Tour of the Remote Control . . . . . . . . . . . . . . . . . . .7

Connections

Choosing a Connection . . . . . . . . . . . . . . . . . . . . .8

Basic Functions

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Using the Search and Skip Functions . . . . . . . . .16

Using the Display Function . . . . . . . . . . . . . . . . .16

Using the Disc and Title Menu . . . . . . . . . . . . . . .17

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Advanced Functions

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . .18

Selecting the Audio Language . . . . . . . . . . . . . . .18

Selecting the Subtitle Language . . . . . . . . . . . . . .19

Changing the Camera Angle . . . . . . . . . . . . . . . . .19

Using the Bookmark Function . . . . . . . . . . . . . . . .20

Using the Zoom Function . . . . . . . . . . . . . . . . . . .20

Clips Menu for MP3/WMA/JPEG/MPEG4/

CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . .21

MP3/WMA/CD Audio Playback . . . . . . . . . . . . . . .21

MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . .22

Playing media files Using the USB

Host Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Picture CD Playback . . . . . . . . . . . . . . . . . . . . . . .25

Picture CD Playback for HD JPEG . . . . . . . . . . . .26

Changing Setup Menu

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . .27

Setting Up the Language Features . . . . . . . . . . . .27

Setting Up the Audio Options . . . . . . . . . . . . . . . .28

Setting Up the Display Options . . . . . . . . . . . . . . .29

Setting Up the Parental Control . . . . . . . . . . . . . .30

Setting Up the HDMI . . . . . . . . . . . . . . . . . . . . . . .32

Reference

Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . .35

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Accessories

- The rechargeable battery incorporated in this

product is not user replaceable.

- For information on its replacement, please con-

tact your service provider.

The accessories which are not supplied are:

Scart Cable

Component Cable

Coaxial Cable.

HDMI-HDMI Cable.

HDMI-DVI Cable.

•

Batteries for Remote

Control (AAA Size)

1. Open the battery cover on the back of the remote

control.

2. Insert two AAA batteries.

Make sure that the

polarities (+ and -) are aligned correctly.

3. Replace the battery cover.

setup

4_ setup

Excellent Sound

Dolby Digital, a technology developed by Dolby

Laboratories, provides crystal clear sound reproduc-

tion.

Screen

Both regular and widescreen(16:9) pictures can be

viewed.

Slow Motion

An important scene can be viewed in slow motion.

1080p Playback

This player upconverts regular DVDs for playback

on 1080p TVs.

Parental Control (DVD)

The parental control allows users to set the level

necessary to prohibit children from viewing harmful

movies such as those with violence, adult subject

matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle)

and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture

with double the scan lines of a conventional inter-

laced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match

your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing

the REPEAT button.

MP3/WMA

This unit can play discs created from MP3/WMA

files.

MPEG4

This unit can play MPEG4 formats within an avi file.

CD Ripping

This features lets you to copy audio files from disc

to USB device into MP3 format. (Only Audio CD

(CD DA)).

HDMI (High Definition Multimedia

Interface)

HDMI reduces picture noise by allowing a pure

digital video/audio signal path from the player to

your TV.

Note

- Discs which cannot be played with this

player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• CDGs play audio only, not graphics.

- Ability to play back may depend on recording

conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW

and DVD-R due to the disc type or recording

conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection.

Because of this, you should only connect your DVD

player directly to your TV, not to a VCR. Connecting

to a VCR results in a distorted picture from copy-

protected DVD discs.

This product incorporates copyright protection

technology that is protected by methods claims of

certain U.S. patents and other intellectual property

rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection

technology must be auzthorized by Macrovision

Corporation, and is intended for home and other

limited viewing uses only unless otherwise autho-

rized by Macrovision Corporation. Reverse engi-

neering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS

(576p,720p,1080p)

“CONSUMERS SHOULD NOTE THAT NOT ALL

HIGH DEFINITION TELEVISION SETS ARE

FULLY COMPATIBLE WITH THIS PRODUCT

AND MAY CAUSE ARTIFACTS TO BE

DISPLAYED IN THE PICTURE, IN CASE OF

576, 720, 1080 PROGRESSIVE SCAN PICTURE

PROBLEMS, IT IS RECOMMENDED THAT THE

USER SWITCH THE CONNECTION TO THE

‘STANDARD DEFINITION’ OUTPUT. IF THERE

ARE QUESTIONS REGARDING YOUR TV SET

COMPATIBILITY WITH THIS MODEL 576p,

720p, 1080p DVD PLAYER, PLEASE CONTACT

SAMSUNG'S CUSTOMER SERVICE CENTER.”

General Features

English _5

● SETUP

This DVD player is capable of playing the following types of discs with the corresponding logos:

Disc Markings

Region Number

Both the DVD player and the discs are coded

by region. These regional codes must match

in order for the disc to play. If the codes do not

match, the disc will not play.

The Region Number for this player is

described on the bottom panel of the player.

You must only insert one DVD disc at a time.

Inserting two or more discs will not allow to

play them back and it may cause damage to

the DVD player.

STEREO

~

DIGITAL

SOUND

STEREO

PAL

Play Region Number

PAL broadcast system in U.K, France,

Germany, etc.

Dolby Digital disc

Stereo disc

Digital Audio disc

DTS disc

MP3 disc

DivX Certification

DivX, DivX Certified,

and associated logos are trademarks of

DivXNetworks, Inc and are used under

license

Disc Type and Characteristics

Disc Types

(Logos)

Recording

Types

Disc

Size

Max. Playing Time Characteristic

DVD

Audio

+

Video

12 Cm

Single-sided 240 min.

Double-sided 480 min

- DVD contains excellent sound and video due to

Dolby Digital and MPEG-2 system.

- Various screen and audio functions can be easi

-

ly selected through the on-screen menu.

8 Cm

Single-sided 80 min.

Double-sided 160 min.

AUDIO-CD

Audio

12 Cm 74 min.

- CD is recorded as a Digital Signal with better

audio quality, less distortion and less deteriora

-

tion of audio quality over time.

8 Cm 20 min.

setup

6_ setup

Description

Front Panel Controls

1. STANDBY/ON ( )

When STANDBY/ON is pressed on, the indicator goes

out and the player is turned on.

2. STANDBY Indicator

When the unit is first plugged in, the indicator lights.

3. DISC TRAY

Place the disc here.

4. OPEN/CLOSE/Stop ( )

Press to open and close the disc tray, Stops disc play.

5. PLAY/PAUSE ( )

Begin or pause disc play.

Rear Panel

1. DIGITAL AUDIO OUT JACKS

- Use coaxial digital cable to connect to a compatible

Dolby Digital receiver.

- Use coaxial digital cable to connect to an A/V

Amplifier that contains a Dolby Digital, MPEG2 or

DTS decoder.

2. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component

Video in jacks. These jacks provide P

R

, P

B

and Y

video.

- If P-SCAN Video Output is selected in Setup Menu,

progressive scan mode will work.

- If I-SCAN Video Output is selected in Setup Menu,

interlaced scan mode will work.

3. AUDIO OUT JACKS

- Connect to the Audio input jacks of your television or

audio/video receiver.

4. VIDEO OUT JACK

- Use a video cable to connect to the Video input jack

on your television.

5. USB Host

- Connect digital still camera, MP3 player, memory

stick, Card reader, or another removable storage

devices.

6. HDMI OUT JACK

- Use the HDMI cable to connect this jack to the HDMI

jack on your television for the best quality picture.

- If an HDMI cable is connected to an HDMI-compat

-

ible TV, HDMI will be output automatically within 10

seconds.

English _7

● SETUP

Note

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).

If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in

the TV’s menu system.

- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conver

-

sion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input.

- There may be no image output if the DVD player is connected to a TV or display that is not compatible

with the above format.

- Refer to the TV's instruction manual for detailed information regarding the HDMI terminal.

- See pages 29 ~ 30 to get more information on how to use the setup menu.

Tour of the Remote Control

1. DVD Power Button

Turns the power on or off.

2. REPEAT Button

Allows you to repeat play a title, chapter, track or disc

3. DISC MENU Button

Brings up the Disc menu.

4. Bookmark Button

5. SEARCH Buttons (

/

)

Allow you to search forward/backward through a disc.

6. STOP Button (

)

7. SUBTITLE (

π

) Button

8. MENU Button

Brings up the DVD player’s menu.

9. AUDIO (√) Button

Use this button to access various audio functions on a disc.

10. ENTER/π/†,√/® Buttons

This button functions as a toggle switch.

11. INFO Button

Displays the current disc mode.

12. OPEN/CLOSE ( ) Button

To open and close the disc tray.

13. REPEAT A-B Butoon

Allows you to repeat play a chosen section (A-B) on a

disc.

14. USB button

15. PAUSE Button (

)

Pause disc play.

16. PLAY Button ( )

Begin disc play.

17. SKIP Buttons (

/

)

Use to skip the title, chapter or track.

18. RETURN Button

Returns to a previous menu.

19. TITLE MENU (®) Button

Brings up the Title menu.

20. CANCEL Button

Use to remove menus or status displays from the

screen.

1

2

3

4

5

8

7

6

10

9

11

12

13

14

15

16

17

18

20

19

connections

8_ connections

The following shows examples of connections commonly used to connect the DVD player with a TV and

other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more information on those

particular components.

Connecting to a TV (VIDEO CVBS)

1

Using video/audio cables, connect the VIDEO (yellow)/

AUDIO (red and white) OUT terminals on the rear of the

DVD player to the

VIDEO (yellow)/AUDIO (red and white)

IN terminals of TV.

2

Turn on the DVD player and TV.

3

Press the input selector on your TV remote control until

the Video signal from the DVD player appears on the TV

screen.

Note

- Noise may be generated if the audio cable is too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)

- The number and position of terminals can vary depending on your TV set. Please refer to the user's

manual of the TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the

DVD player.

RED

WHITE

YELLOW

RED

WHITE

YELLOW

Audio

Cable

Video Cable

Choosing a Connection

English _9

● CONNECTIONS

Connection to a TV (Interlace)

- Connecting to your TV using Component video cables.

- You will enjoy high quality and accurate color reproduction images. Component video separates the pic

-

ture element into black and white(Y), blue(P

B

), red(P

R

) signals to present clear and clean images. (Audio

signals are delivered through the audio output.)

1

Using component video cables (not included), connect the

COMPONENT VIDEO OUT terminal on the rear of the

DVD player to the

COMPONENT IN terminal of TV.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

3

Press the input selector on your TV remote control until

the Component signal from the DVD player appears on the

TV screen.

4

Set the Video Output to I-SCAN in the Display Setup

menu. (See pages

29-30)

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)

- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “P

R

, P

B

, Y”

depending on the manufacturer. The number and position of terminals can vary depending on the TV set.

Please refer to the user's manual of the TV.

RED

WHITE

RED

WHITE

RED

BLUE

GREEN

RED

BLUE

GREEN

Audio Cable

Component cable

connections

10_ connections

Connection to a TV (Progressive)

1

Using component video cables (not included), connect the

COMPONENT VIDEO OUT terminal on the rear of the

DVD player to the

COMPONENT IN terminal of TV.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

3

Press the input selector on your TV remote control until

the Component signal from the DVD player appears on the

TV screen.

4

Set the Video Output to P-SCAN in the Display Setup

menu. (See pages 29-30)

To see the progressive video output,

You need a TV set supporting the progressive scan

input function. And you have to set up the TV

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive

Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s

menu system.

- Depending on your TV, the connection method may differ from the illustration above.

Note

- What is "Progressive Scan"?

Progressive scan has twice as many scanning lines as the interlace output method has. Progressive

scanning method can provide better and clearer picture quality.

RED

WHITE

RED

WHITE

RED

BLUE

GREEN

RED

BLUE

GREEN

Audio Cable

Component cable

English _11

● CONNECTIONS

Connecting to a TV with DVI Jack

Connecting to a TV with HDMI Jack

HDMI VIDEO Specifications

- Depending on your TV, certain HDMI output resolutions may not work.

- Please refer to the user's manual of your TV.

- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10

-seconds.

- If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture

-quality.

- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player

using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC).

(See page 32).

- If your TV has an

logo, then it will Supports the Anynet+ Function.

RED

WHITE

RED

WHITE

Audio Cable

HDMI-DVI cable

HDMI cable

1

Using an HDMI-DVI cable (not included), connect the

HDMI OUT terminal on the rear of the DVD player to the

DVI IN terminal of your TV.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

3

Press the input selector on your TV remote control until

the DVI signal from the DVD player appears on your TV

screen.

1

Using the HDMI-HDMI cable connect the HDMI OUT termi-

nal on the rear of the DVD player to the

HDMI IN terminal

of your TV.

2

Press the input selector on your TV remote control until

the HDMI signal from the DVD player appears on your TV

screen.

connections

12_ connections

• HDMI (High Definition Multimedia Interface)

HDMI is an interface to enable the digital transmission

of video and audio data with just a single connector.

Using HDMI, the DVD player transmits a digital video

and audio signal and displays a vivid picture on a TV

having an HDMI input jack.

• HDMI connection description

HDMI connector - Both uncompressed video data and

digital audio data (LPCM or Bit Stream data).

- Though the player uses a HDMI cable, the player

outputs only a pure digital signal to the TV.

- If TV does not support HDCP (High-bandwidth

Digital content protection), snow noise appears on

the screen.

• Why does Samsung use HDMI?

Analog TVs require an analog video/audio signal.

However, when playing a DVD, the data transmitted

to a TV is digital. Therefore either a digital-to-analog

converter (in the DVD player) or an analog-to-digital

converter (in the TV) is required. During this conver

-

sion, the picture quality is degraded due to noise and

signal loss. DVI technology is superior because it

requires no D/A conversion and is a pure digital sig

-

nal from the player to your TV.

• What is the HDCP?

HDCP (High-bandwidth Digital Content Protection)

is a system for protecting DVD content outputted

via DVI from being copied. It provides a secure

digital link between a video source (PC, DVD. etc)

and a display device (TV, projector . etc). Content is

encrypted at the source device to prevent unauthor

-

ized

English _13

● CONNECTIONS

Connection to an Audio System (2 Channel Amplifier)

1

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of the Amplifier.

2

Using the video signal cable(s), connect the VIDEO or

COMPONENT OUT terminals on the rear of the DVD

player to the

VIDEO or COMPONENT IN terminal of your

TV as described on pages 8 to 11.

3

Turn on the DVD player, TV, and Amplifier.

4

Press the input select button of the Amplifier to select

external input in order to hear sound from the DVD player.

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause

damage to the speakers or to your hearing.

- Please set the audio in the menu screen according to the Amplifier. (See pages 28 to 29)

- The position of terminals can vary depending on the Amplifier.

Please refer to the user's manual of the Amplifier.

RED

WHITE

RED

WHITE

2-Channel stereo amp

Audio Cable

connections

14_ connections

Connection to an Audio System (Dolby Digital, MPEG2 or DTS Amplifier)

1

If using a coaxial cable (not included), connect the

DIGITAL AUDIO OUT (COAXIAL) terminal on the rear

of the DVD player to the

DIGITAL AUDIO IN (COAXIAL)

terminal of the Amplifier.

2

Using the video signal cable(s), connect the VIDEO,

COMPONENT or HDMI OUT terminals on the rear of the

DVD player to the

VIDEO, COMPONENT or DVI IN termi-

nals of your TV as described on pages 8 to 11.

3

Turn on the DVD player, TV, and Amplifier.

4

Press the input select button of the Amplifier to select

external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's

audio input.

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause

damage to the speakers or to your hearing.

- Please set the audio in the menu screen according to the Amplifier. (See pages 28 to 29)

- The position of terminals can vary depending on the Amplifier.

Please refer to the user's manual of the Amplifier.

Coaxial Cable

Dolby Digital or

DTS amp

English _15

● BASIC FUNCTIONS

basic functions

Playing a Disc

Before Play

- Turn on your TV and set it to the correct Video

Input by pressing TV/VIDEO button on the TV

remote control.

- If you connected an external Audio System, turn

on your Audio System and set it to the correct

Audio Input.

After plugging in the player, the first time you press the DVD

POWER button, this screen comes up: If you want to select

a language, Press the

π/† buttons, and then press the

ENTER button. (This screen will only appear when you plug

in the player for the first time.)

If the language for the startup screen is not set, the set

-

tings may change whenever you turn the power on or off.

Therefore, make sure that you select the language you want

to use.

Once you select a menu language, you can change it by

pressing the (

) button on the front panel of the unit

for more than 5 seconds with no disc in the unit. Then the

SELECT MENU LANGUAGE window appears again where

you can reset your preferred language.

Playback

1. Press the OPEN/CLOSE ( ) button. The STANDBY indi-

cator light goes out and the tray opens.

2. Place a disc gently into the tray with the disc’s label fac

-

ing up.

3. Press the

PLAY ( ) button or OPEN/ CLOSE ( ) but-

ton to close the disc tray.

When you stop disc play, the

player remembers where you stopped, so when you

press PLAY (

) button again, it will pick up where you

left off.

4. Stopping Play

Press the

STOP ( ) button during play.

6. Pausing Play

Press the

PAUSE ( ) button on the remote control during

play.

- Screen stops, no sound.

To resume, press the

PLAY ( ) button once again.

7. Slow Motion Play

Press the

SEARCH (

/

) button to choose the play

speed between 1/2, 1/4 1/8 and 1/16th of normal speed

during

PAUSE mode.

- No sound is heard during slow mode.

- Press the

PLAY( ) button to resume normal play.

5. Removing Disc

Press the

OPEN/CLOSE ( ) button.

Note

- If the player is left in the stop mode for more

than one minute without any user interaction, a

screen saver will be activated. Press the PLAY

( ) button to resume normal play.

- If the player is left in the stop mode for more than

about 30 minutes, the power will automatically

shut off.(Automatic Power-Off Function)

- If the player is left for about 5 minutes in pause

mode, it will stop.

- This ( ) icon indicates an invalid button press.

Select Menu Language

English

Français

Deutsch

Español

Italiano

Nederlands

8. Step Motion Play (Except CD)

Press the

SKIP ( ) button on the remote control

during

PAUSE mode.

- Each time the button is pressed, a new frame will

appear.

- No sound is heard during

STEP mode.

- Press the

PLAY ( ) button to resume normal play.

- You can only perform step motion play in the forward

direction.

basic functions

16_ basic functions

Using the Search and Skip

Functions

During play, you can search quickly through a chapter or

track, and use the skip function to jump to the next selection.

Searching through a Chapter or

Track

During play, press the SEARCH ( or ) button on the

remote control for more than 1 second.

Note

- The speed marked in this function may be

different from the actual playback speed.

- No sound is hearing during search mode

(Except CD).

Skipping Tracks

During play, press the SKIP (

or ) button.

- When playing a DVD, if you press the SKIP ( ) button, it

moves to the next chapter. If you press the SKIP

( ) button, it moves to the beginning of the chapter. One

more press makes it move to the beginning of the previous

chapter.

- When playing a CD in Menu Off mode, if you press the

SKIP (

) button, it moves to the next track. If you press

the SKIP (

) button, it moves to the beginning of the

track. One more press makes it move to the beginning of

the previous track.

Using the Display Function

When Playing a DVD/MPEG4

1. During play, press the INFO button on the remote control.

2. Press the

π/† buttons to select the desired item.

3. Press the

√/® buttons to make the desired setup and then

press the

ENTER button.

4. To make the screen disappear, press the INFO button

again.

Note

DVD 2X, 4X, 64X, 128X

CD 2X, 4X, 8X

To access the desired title when there is more

than one in the disc.

For example, if there is more than one movie

on a DVD, each movie will be identified.

Most DVD discs are recorded in chapters so

that you can quickly nd a specic passage

(similar to tracks on an audio CD).

Allows playback of the lm from a desired

time. You must enter the starting time as a

reference.

The time search function does not operate

on some discs

Refers to the lm's soundtrack language.

In the example, the soundtrack is played in

English 5.1CH.A DVD disc can have up to

eight different soundtracks.

Refers to the subtitle languages available

in the disc. You will be able to choose the

subtitle languages or, if you prefer, turn them

off from the screen. A DVD disc can have up

to 32 different subtitles

E

Z

The EZ View funtion is use for changing the

aspect ratio in DVD.

This button has function as shortcut. Press

enter to activate the Zoom function.

To access the desired Angle function.

Some DVD disc are have more than one

recorded angle.

English _17

● BASIC FUNCTIONS

Using the Disc Menu

1. During the playback of a DVD disc, press the DISC MENU

button on the remote control.

2. Press the

π/† buttons for navigation/change selection,

then-press

ENTER button.

3. To make the screen disappear, press the

RETURN or DISC

MENU button again.

Note

- The disc menu may not work on certain disc

types.

- You can also use the Disc Menu, using the

DISC MENU button on the remote control.

Press the REPEAT button to change playback

mode.

When playing a DVD

- DVD repeats play by chapter or title.

- Chapter : repeats the chapter that is playing.

- Title : repeats the title that is playing.

- Disc : repeats the disc that is playing.

- Off

Using the Title Menu

1. During the playback of a DVD disc, press the ® /TITLE

MENU button on the remote control.

2. Press the

π/† buttons to select for navigation/change

selection, then press the

ENTER button.

3. To make the screen disappear, press the

RETURN button

again.

Note

- The disc menu may not work on certain disc

types.

- Title Menu will only be displayed if there are at

least two titles in the disc.

Using the Disc and Title

Menu

Repeat Play

Chapter

Title

Disc

Off

Using the A-B Repeat function

1. Press the REPEAT A-B button on the remote control at

the point where you want repeat play to start (A).

2. Press the REPEAT A-B button on the remote control at

the point where you want the repeat play to stop (AB).

DVD

A

AB

Off

Note

- A-B REPEAT allows you to set point (AB) directly

after point (A) has been set.

- The disc menu may not work on certain disc

types.

This feature allows you to slowly repeat scenes

containing sports, dancing, musical instruments

being played etc., so you can study them more

closely.

When playing a DVD

1. During play, press the PAUSE ( ) button.

2. Press the

SEARCH (

/

) button to choose the play

speed between 1/2, 1/4, 1/8 and 1/16 of normal during

PAUSE mode.

Slow Play

advanced functions

18_ advanced functions

Adjusting the Aspect Ratio

(EZ View)

To play back using aspect ratio

(DVD)

1. During play, press the INFO button on the remote control.

2. Press the

π/† buttons to select

E

Z

icon. Press the √/®

buttons, the screen size change when these button is

pressed.

3. To make the screen disappear, press the INFO button again.

If you are using a 16:9 TV

For 16:9 aspect ratio discs

- WIDE SCREEN

Displays the content of the DVD title in 16:9 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off.

When playing a 2.35:1 aspect ratio disc, the black bars at

the top and bottom of the screen will disappear. The picture

will look vertically stretched. (Depending on the type of

disc, the black bars may not disappear completely.)

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and

the central portion of the screen is enlarge

For 4:3 aspect ratio discs

- Normal Wide

Displays the content of the DVD title in 16:9 aspect ratio.

The picture will look horizontally stretched.

- SCREEN FIT

The top and bottom portions of the screen are cut off and

the full screen appears.

The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are

cut off and the central portion of the screen is enlarged.

- Vertical Fit

When a 4:3 DVD is viewed on a 16:9 TV, black bars will

appear at the left and right of the screen in order to prevent

the picture from looking horizontally stretched.

If you are using a 4:3 TV

For 16:9 aspect ratio discs

- 4:3 Letter Box

Displays the content of the DVD title in 16:9 aspect ratio.

The black bars will appear at the top and bottom of the

screen.

- 4:3 Pan Scan

The left and right portions of the screen are cut off and the

central portion of the 16:9 screen is displayed.

- SCREEN FIT

The top and bottom portions of the screen are cut off and a

full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and

the central portion of the screen is enlarged.

For 4:3 aspect ratio discs

- Normal Screen

Displays the content of the DVD title in 4:3 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off and

the full screen appears. The picture will look vertically

stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are cut

off and the central portion of the screen is enlarged.

Note

This function may behave differently depending on

the type of disc.

Selecting the Audio

Language

You can select a desired audio language quickly and

easily with the

√/

AUDIO button.

Using the

√/

AUDIO button (DVD/

MPEG4)

1. Press the

√/

AUDIO button. The Audio changes when the

button is pressed repeatedly. The audio languages are rep

-

resented by abbreviations.

DVD

ENG DTS 5.1 CH

English _19

● ADVANCED FUNCTIONS

Press

√/

AUDIO button

at remote control repeat

-

edly to select the desired

Audio on MPEG4 then

press the

ENTER .

MPEG4

Note

- This function depends on audio languages

encoded on the disc and may not work.

-

A DVD disc can contain up to 8 audio languages.

- To have the same audio language come up

whenever you play a DVD;

Refer to “Using the Audio Language” on page 28.

- Possible warning messages that may appear if the

device (TV) that connected to the HDMI can't sup-

port RAW digital audio.

Selecting the Subtitle

Language

You can select a desired subtitle quickly and

easily with the

π/SUBTITLE button.

Using the

π/

SUBTITLE button

(DVD/MPEG4)

1. Press the

π/

SUBTITLE button. The subtitle languages are

represented by abbreviations. The subtitle changes when

the button is pressed repeatedly.

Note

- You have to change the desired subtitle in the

Disc Menu, according to discs. Press the DISC

MENU button.

- This function depends on what subtitles are

encoded on the disc and may not work on all DVDs.

- A DVD disc can contain up to 32 subtitle

languages.

- To have the same subtitle language come up

whenever you play a DVD; Refer to “Using the

Subtitle Language” on page 28.

DVD

Repeatedly Press

π/

SUBTITLE button

on the remote control to

select the desired

subtitle language on

MPEG4 then press

ENTER .

MPEG4

1/1 MP3 2CH

English

Subtitle 1/5

Changing the Camera

Angle

When a DVD contains multiple angles of a particular

scene, you can use the ANGLE function.

Using the ANGLE function (DVD)

If the disc contains multiple angles, the ANGLE

appears on the screen.

1. During play, press the INFO button on the remote control.

2. Press the

π/† buttons to select icon.

3. Press the

√/® buttons on the remote control to select the

desired angle.

4. To make the screen disappear, press the INFO button again.

Note

- If the disc has only one angle, this feature won’t

work. Currently, very few discs have this feature.

- Depending on the disc, these functions may not

work.

advanced functions

20_ advanced functions

Recalling a Marked Scene

1. During play,press the Bookmark button on the remote

control.

2. Press the √/®/π/† buttons to select a marked

scene.

3. Press the PLAY ( ) button to skip to the

marked scene.

CANCEL

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

1

2

1

2

3

TT:01 CH:05 Time 0:39:23

Clearing a Bookmark

1. During play,press the Bookmark button on the remote

control.

2. Press the √/®/π/† buttons to select a marked

scene.

3. Press the CANCEL button to delete a bookmark

number.

CANCEL

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

1

2

1

2

3

TT:01 CH:05 Time 0:39:23

Using the Zoom Function

Using the Zoom Function (DVD)

1. During play, press the INFO button on the remote control.

2. Press the π/† buttons to select icon, then press the

ENTER button to zoom in 2x, 3x, 4x.

3. To make the screen disappear, press the INFO button again.

2x

Clips Menu for MP3/WMA/

JPEG/MPEG4/CD Audio

CD Audio or discs with MP3/WMA/JPEG/MPEG4

contain individual songs and/or pictures that will be

organized into folders on this unit as shown below.They

are similar to how you use your computer to put files

into different folders.

Open the disc tray.

Place the disc on the tray.

Close the tray.

The tray closes and this

screen displays.

001/004

- : Current Playback Mode : There are four

modes.

They can be selected in order by pressing the

REPEAT button.

- Off : Normal Playback.

- Track : Repeats the current track.

- Folder : Repeats the current folder.

- Random : Files in the disc will be played in

random order.

Using the Bookmark

Function

This feature lets you bookmark sections of a DVD so

you can quickly find them at a later time.

Using the Bookmark Function (DVD)

1. During play, press the Bookmark button on the remote con

trol.

2. When You reach the scene you want to mark, press the

ENTER button. Up to 12 scenes may be marked at a time.

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

1

2

1

2

3

TT:01 CH:05 Time 0:39:23

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

1

2

1

2

3

TT:01 CH:05 Time 0:39:23

Note

- These functions may not Work on certain disc

types.

Off

La page charge ...

Samsung DVD-H1080R Manuel utilisateur

Samsung DVD-H1080R Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents