HTC ds 14dmr Manuel utilisateur

DS18DMR

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et propriétaires

avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être conservé dans un

endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should

be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

Cordless Driver Drill

Model Variable speed Driver Drill

Modèle (Operated with ET18DM)

Modelo Perceuse-visseuse à batterie

Taladro atornillador a batería

DS 14DMR

•

DS 18DMR

Page

ASSEMBLY AND OPERATION ............................. 14

APPLICATIONS ................................................. 14

REMOVAL AND INSTALLATION METHOD

OF BATTERY .............................................. 14

CHARGING METHOD ....................................... 14

BEFORE USE ....................................................... 20

OPERATION....................................................... 21

THE SCOPE AND SUGGESTIONS

FOR USES .................................................. 27

HOW TO SELECT TIGHTENING TORQUE....... 27

MAINTENANCE AND INSPECTION ..................... 28

ACCESSORIES ....................................................... 30

STANDARD ACCESSORIES ............................. 30

OPTIONAL ACCESSORIES ............................... 31

TABLE DES MATIERES

Français

Page

INFORMATIONS IMPORTANTES DE SÉCURITÉ

..... 32

SIGNIFICATION DES MOTS D’AVERTISSEMENT

..... 32

SECURITE ................................................................ 33

REGLES GENERALE DE SECURITE – POUR TOUS

LES OUTILS FONCTIONNANT SUR BATTERIE

.... 33

REGLES DE SECURITE SPECIFIQUES ET SYMBOLES

.. 35

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR LE CHARGEUR DE BATTERIE .......... 37

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L’UTILISATION DE LA BATTERIE

ET DU CHARGEUR DE BATTERIE .............. 38

MISE AU REBUT D’UNE BATTERIE USÉE ........ 39

DESCRIPTION FONCTIONNELLE ........................... 40

MODELE .............................................................. 40

NOM DES PARTIES ............................................ 40

SPECIFICATIONS ................................................ 42

Page

ASSEMBLAGE ET FONCTIONNEMENT ................ 43

UTILISATIONS .................................................... 43

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 43

MÉTHODE DE RECHARGE ................................. 43

AVANT L’UTILISATION ...................................... 50

UTILISATION ....................................................... 50

PLAGE D’UTILISATION ET SUGGESTIONS ..... 56

SÉLECTION DU COUPLE DE SERRAGE ............ 56

ENTRETIEN ET INSPECTION .................................. 57

ACCESSOIRES ......................................................... 59

ACCESSOIRES STANDARD ............................... 59

ACCESSOIRES EN OPTION................................ 60

Página

MONTAJE Y OPERACIÓN ...................................... 72

APLICACIONES ................................................... 72

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA............................................ 72

MÉTODO DE CARGA .......................................... 72

ANTES DE LA UTILIZACIÓN .............................. 79

OPERACIÓN ........................................................ 79

ALCANCE Y SUGERENCIAS PARA LA

UTILIZACIÓN................................................ 85

FORMA DE SELECCIONAR EL PAR DE APRIETE

... 86

MANTENIMIENTO E INSPECCIÓN ........................ 87

ACCESORIOS........................................................... 89

ACCESORIOS ESTÁNDAR ................................. 89

ACCESORIOS OPCIONALES .............................. 90

CONTENTS

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD

.... 61

SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN

.... 61

SEGURIDAD............................................................. 62

NORMAS GENERALES DE SEGURIDAD – PARA TODAS

LAS HERRAMIENTAS ALIMENTADAS CON BATERÍA

... 62

NORMAS Y SÍMBOLOS ESPECÍFICOS DE

SEGURIDAD ................................................. 64

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA EL CARGADOR DE BATERÍAS

.................. 66

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA LA BATERÍA Y EL CARGADOR DE BATERÍAS

... 67

ELIMINACIÓN DE LAS BATERÍAS AGOTADAS

... 68

DESCRIPCIÓN FUNCIONAL.................................... 69

MODELO .............................................................. 69

NOMENCLATURA............................................... 69

ESPECIFICACIONES............................................ 71

English

Page

IMPORTANT SAFETY INFORMATION .............. 3

MEANINGS OF SIGNAL WORDS ...................... 3

SAFETY .................................................................... 4

GENERAL SAFETY RULES – FOR ALL

BATTERY OPERATED TOOLS..................... 4

SPECIFIC SAFETY RULES AND SYMBOLS....... 6

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER ........................... 8

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER...................................... 9

DISPOSAL OF THE EXHAUSTED BATTERY ... 10

FUNCTIONAL DESCRIPTION................................ 11

MODEL............................................................... 11

NAME OF PARTS .............................................. 11

SPECIFICATIONS .............................................. 13

English

3

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

English

4

SAFETY

GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders, children and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery.

A charger that may be suitable for one type of battery may create a risk of fire when

used with another battery.

(2) Use battery operated tool only with specifically designed battery pack.

Use of any other batteries may create a risk of fire.

(3) Do not abuse the cord. Never use the cord to carry the tools or pull the plug from

an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase the risk of electric shock.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off position before inserting battery.

Carrying tools with your finger on the switch or inserting the battery pack into a

tool that have the switch on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key

that is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enable better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

English

5

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead

to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tools. Such

preventive safety measures reduce the risk of starting the tool accidentally.

(5) Disconnect the battery or cord form the tool before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures reduce

the risk of starting the tool accidentally (when used with power supply).

(6) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

(7) When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns, or a fire.

(8) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(9) Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tools operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

(10)Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used

on another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instruction may create a risk of electric shock or injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

English

6

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

2. ALWAYS wear ear protectors when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

3. NEVER place hands or other body parts near the drill bit or chuck during operation.

Hold the drill by its handle only.

4. Because the cordless driver drill operates by battery power, be aware of the fact that it

can begin to operate at any time.

5. When working at elevated locations, clear the area of all other people and be aware of

conditions below you.

6. NEVER touch moving parts.

NEVER place your hands, fingers or other body parts near the tool’s moving parts.

7. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

8. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

9. NEVER use a power tool for applications other than those specified.

NEVER use a power tool for applications other than those specified in the Instruction

Manual.

10. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw

the tool. NEVER allow the tool to be operated by children, individuals unfamiliar with

its operation or unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

12. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

13. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to yourself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

English

7

14. NEVER use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

15. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner, benzine, carbon tetrachloride and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

17. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI

Standard Z87.1.

18. Definitions for symbols used on this tool

V

............

volts

—

---

...........

direct current

no

..........

no load speed

---/min

...

revolutions per minute

English

8

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

1. This manual contains important safety and operating instructions for battery charger

Model UC14YFA/UC24YJ/UC18YG.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI rechargeable battery type EB7, EB9, EB12,

EB14, EB18 series and EB24B. Other type of batteries may burst causing personal injury

and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold by the battery charger manufacturer

may result in a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug when disconnecting

battery charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same number, size, and shape as those of

plug on battery charger;

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is large enough for AC ampere rating of battery charger as specified

in Table 1.

* If the input rating of a battery charger is given in watts rather than in amperes, the

corresponding ampere rating is to be determined by dividing the wattage rating by the

voltage rating–for example:

9. Do not operate battery charger with damaged cord or plug–replace them immediately.

1,250 watts

125 volts

= 10 amperes

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

English

9

10. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

12. To reduce risk of electric shock, unplug charger from receptacle before attempting any

maintenance or cleaning. Removing the battery will not reduce this risk.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

BATTERY AND BATTERY CHARGER

You must charge the battery before you can use the cordless driver drill. Before using the

model UC14YFA/UC24YJ/UC18YG battery charger, be sure to read all instructions and

cautionary statements on it, the battery and in this manual.

REMEMBER: USE ONLY HITACHI BATTERY TYPES EB7 SERIES, EB9 SERIES, EB12 SERIES,

EB14 SERIES, EB18 SERIES AND EB24B. OTHER TYPES OF BATTERIES MAY BURST AND

CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING: Improper use of the battery or battery charger can lead to serious injury.

To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or is completely worn out. The

battery can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s air vents. Electric shock or

damage to the battery charger may result.

5. NEVER charge outdoors. Keep the battery away from direct sunlight and use only

where there is low humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F (0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to charge.

11. NEVER store the battery or battery charger in places where the temperature may

reach or exceed 104°F (40°C).

12. ALWAYS operate charger on standard household electrical power (120 volts). Using

the charger on any other voltage may overheat and damage the charger.

13. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.

14. ALWAYS disconnect the power cord from its receptacle when the charger is not in

use.

English

10

DISPOSAL OF THE EXHAUSTED BATTERY

WARNING: Do not dispose of the exhausted battery. The battery must explode if it

is incinerated. The product that you have purchased contains a

rechargeable battery. The battery is recyclable. At the end of it’s useful

life, under various state and local laws, it may be illegal to dispose of

this battery into the municipal waste stream. Check with your local

solid waste officials for details in your area for recycling options or

proper disposal.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

English

11

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the

safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and

understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own power tool.

MODEL

DS14DMR (BFK): with charger (UC14YFA) and case

DS14DMR (BGK): with charger (UC18YG) and case

DS18DMR (HLCK): with charger (UC24YJ) and case

DS18DMR (BLGK): with charger (UC18YG) and case

NAME OF PARTS

1. Cordless Driver Drill (DS14DMR and DS18DMR)

Nameplate

Push Button

Battery

Switch Trigger

Cap

Keyless Chuck

Shift Knob

Handle

Push Button

Side Handle

Bit Holder

English

12

Nameplate

Terminal Hole

Latch

Nameplate

Terminal Hole

Latch

䡬 Battery (EB14B)

(For DS14DMR)

䡬 Battery (EB1830HL or

EB1820L)

(For DS18DMR)

Fig. 1

2. Battery Charger

Fig. 2

Nameplate

Battery

Push Button

Switch Trigger

Cap

Keyless Chuck

Shift Knob

Handle

Bit Holder

Side Handle

Push Button

Caution Plate

Battery Installation Hole

Pilot Lamp

Nameplate

English

13

Model DS14DMR DS18DMR

Motor DC motor

No-load speed Low 0–400/min 0–400/min

High 0–1,500/min 0–1,600/min

Capacity Drilling

Wood (Thickness

1-3/4"

(44 mm)

2" (50 mm)

11/16" (18 mm)) (Soft Wood) (Soft Wood)

Metal (Thickness

1/2" (13 mm) 1/2" (13 mm)

1/16" (1.6 mm)) (Mild Steel or (Mild Steel or

Aluminum) Aluminum)

Screw Wood screw #20 × 3" #20 × 4"

Driver

(8 mm × 75 mm) (8 mm × 100 mm)

Small screw 1/4" (6 mm) 1/4" (6 mm)

Drill chuck capacity Maximum gripping diameter 1/2" (13 mm)

Battery Model EB14B EB1820L EB1830HL

Type

Nickel cadmium battery

Nickel-Metal Hydride battery

Voltage DC 14.4 V DC 18 V

Charging & discharging UC14YFA /UC24YJ....................about 1,000 times

frequency UC18YG ........................................about 300 times

Weight 5.1 lbs. (2.3 kg) 5.5 lbs. (2.5 kg)

SPECIFICATIONS

1. Cordless Driver Drill

Fig. 4Fig. 3

Charge Time Lamp

Charge

Status Lamp

Caution Plate

Nameplate

Battery Installation Hole

Battery installation hole

Pilot lamp

Cord

Plug

Nameplate

2. Battery Charger

NOTE: The charging time may vary according to temperature and power source voltage.

Model UC14YFA UC24YJ UC18YG

Input power source Single phase: AC 120 V 60 Hz

Charging time Approx. 50 min. Approx. 28min. Approx. 50min.

(At a temperature of 68°F (20°C))

Charging voltage DC 7.2–14.4 V DC 7.2–24 V DC 7.2–18 V

Charging current DC 2.6 A DC 7.5 A DC 2.6 A

Weight 1.3 lbs. (0.6 kg) 2.2 lbs. (1.0 kg) 0.7 lbs. (0.3 kg)

English

14

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Use as a drill

Drilling of soft steel, wood, plastic and aluminum materials

䡬 Use as a screwdriver

Tightening and loosening of machine screws, wood screws and tapping screws

REMOVAL AND INSTALLATION METHOD OF BATTERY

䡬 How to install the battery

Align the battery with the groove in tool handle and slip it into place.

Always insert it all the way until it locks in place with a little click. If not, it may accidentally

fall out of the tool, causing injury to you or someone around you. (Fig. 5)

䡬 How to remove the battery

Withdraw battery from the tool handle while pressing the latch (2 pcs.) on the sides of

the battery. (Fig. 5)

Fig. 5

CHARGING METHOD

The following is an explanation of charging methods when using the battery charger

UC14YFA, UC24YJ or UC18YG. When charging using the ET18DM Multi Charger, please

read the separate ET18DM Instruction manual.

NOTE: Before plugging into the receptacle, make sure the following points.

䡬 The power source voltage is stated on the nameplate.

䡬 The cord is not damaged.

WARNING: Do not charge at voltage higher than indicated on the nameplate.

If charged at voltage higher than indicated on the nameplate, the

charger will burn up.

Latch

Push

Handle

Battery

Insert

Pull out

Switch Trigger

English

15

1. Insert the plug of battery charger into the receptacle.

When the plug of battery charger has been inserted into

the receptacle, pilot lamp will blink in red. (At 1-second

intervals)

WARNING:

Do not use the electrical cord if

damaged. Have it repaired immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in Fig. 6. Make sure it contacts the

bottom of the battery charger.

3. Charging

When the battery is connected to the battery charger, charging will commence and the

pilot lamp will light in red. (See Table 2)

NOTE: If the pilot lamp flickers in red, pull out the plug from the receptacle and check if

the battery is properly mounted.

When the battery is fully charged, the pilot lamp will blink in red slowly. (At 1-second

intervals) (See Table 2)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in Table 2, according to the condition

of the charger or the rechargeable battery.

Fig. 6

Battery

Pilot Lamp

Table 2

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Malfunction in the battery or the

charger

The battery temperature is high,

making recharging impossible.

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flickers

(RED)

Lights

(GREEN)

English

16

(2) Regarding the temperature of the rechargeable battery

The temperatures for rechargeable batteries are as shown in the table below, and

batteries that have become hot should be cooled for a while before being recharged.

Table 3 Recharging of batteries that have become hot

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

● When the battery charger has been continuosly used, the battery charger will be heated,

thus constituting the cause of the failures. Once the charging has been completed,

give 15 minutes rest until the next charging.

● If the battery is rechraged when it is warm due to battery use or exposure to sunlight,

the pilot lamp may light in green.

The battery will not be recharged. In such a case, let the battery cool before charging.

● When the pilot lamp flickers in red (at 0.2–second intervals), check for and take out

any foreign objects in the charger’s battery installation hole. If there are no foreign

objects, it is probable that the battery or charger is malfunctioning. Take it to your

authorized Service Center.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been

used for an extended period is not activated, the electric discharge might be low when

using them the first and second time. This is a temporary phenomenon, and normal

time required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and

recharge its battery. If you continue to use the tool and exhaust the electric current, the

battery may be damaged and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged

immediately after use, its internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it after it has cooled for a while.

Rechargeable batteries Temperatures at which the battery can be recharged

EB14B 23°F—140°F (–5°C—60°C)

English

17

Fig. 7

Battery

Charge

Status Lamp

Charge Time

Lamp

1. Insert the plug of battery charger into the receptacle.

When the plug of battery charger has been inserted into

the receptacle, the charge status lamp will blink in red.

(At 1-second intervals)

WARNING:

Do not use the electrical cord if

damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in Fig. 7. Make sure it contacts the

bottom of the battery charger.

3. Charging

When the battery is connected to the battery charger, charging starts, and the charge

time lamp lights red, orange, or green according to the remaining charging time. (See

Table 4)

(1) Lamp indications

This charger is equipped with a charge time lamp that indicates remaining charging

time, and a charge status lamp that indicates battery status as shown in Table 4.

(a) Charging time

After charging commences, the charge time lamp lights red indicating 30 minutes,

orange indicating 20 minutes, and green indicating 5 minutes until completion.

When the battery is fully charged, the charge status lamp lights green, and the

buzzer sounds continuously for 6 seconds.

(b) Overheat standby

When the battery is overheated, it cannot be charged, and the charge time lamp

flashes red (in 0.6 second intervals). Leave the battery inserted in the charger, and

charging will commence when the battery cools down.

(c) Charging impossible

When there is a malfunction with the battery or charger, the charge status lamp

flashes orange rapidly (in 0.2 second intervals), and the buzzer sounds intermittently

for 5 seconds.

English

18

Lamp indications Status lamp

Charging time Lights Lights continuously

30 minutes until charging complete.

Charge

30 minutes red

time Charging time Lights Lights continuously

20 minutes until charging complete.

lamp

20 minutes orange

(red/ Charging time Lights Lights continuously

5 minutes until charging complete.

orange/

5 minutes green

green)

Overheat standby

Blinks

Lights for 0.3 seconds, off 0.3 seconds

Battery overheated. Unable to charge.

red

(Charging will commence when battery cools.)

Charge

Before charging

Blinks

Lights for 0.5 seconds, off 0.5 seconds

Power cord is connected to

status

red receptacle.

lamp

Charging complete

Lights Lights continuously

(red/

green

orange/

Charging Blinks

Lights for 0.1 seconds, off 0.1 seconds

Battery or charger malfunction.

green)

impossible orange ■■■■■■■■■■■

Table 4 Lamp indications

(2) Regarding the temperature of the rechargeable battery

The temperatures for rechargeable batteries are as shown in the table below, and

batteries that have become hot should be cooled for a while before being recharged.

Table 5 Recharging of batteries that have become hot

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

● Repair is required if the receptacle is not secured properly or the power cord does not

stay in the receptacle. Consult your electrician. Using the charger in this condition

may lead to fire.

● If the charge status lamp is blinking orange rapidly (in 0.2 second intervals) and the

buzzer sounds intermittently for 5 seconds, check that the hole for connecting the

battery is not obstructed. Remove any obstructions. If no obstructions are found, the

battery or charger may be malfunctioned. Return both to your place of purchase.

● If the charge time lamp does not light when the power cord is connected to the

receptacle, disconnect the power cord, and check that the battery is attached correctly.

● The battery retains heat when used or left for prolonged periods in direct sunlight. In

this state, the charge time lamp flashes red, and the battery cannot be charged

immediately. Leave the battery inserted in the charger, and charging will commence

when the battery cools down.

Rechargeable batteries Temperatures at which the battery can be recharged

EB1830HL 32°F—122°F (0°C—50°C)

English

19

● If the lamp goes out while charging, disconnect the power cord, and leave for 3 to 5

minutes before reconnecting. If the problem persists, call for repairs.

● Leave 5 minutes between charging batteries as the charger may overheat leading to

malfunction.

● The battery life is finished if it can only be used for short periods even when fully

charged. Purchase a new battery. Continuing to use a depleted battery may cause the

charger to malfunction.

NOTE:

䡬 Charging times may be longer depending on the surrounding temperature and battery

conditions.

䡬 Charge time lamp indications are only a guide, and may vary depending on the

surrounding temperature and battery conditions.

䡬 Remove the battery from the charger when not in use.

Revitalizing the battery (trickle recharge)

A new battery or a battery that has not been used for extensive periods may not charge

completely due to internal chemicals being inert.

Leave the battery inserted in the charger for 8 to 12 hours after charging is complete.

The charger automatically “revitalizes” the battery by trickle recharging.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and

recharge its battery. If you continue to use the tool and exhaust the electric current, the

battery may be damaged and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged

immediately after use, its internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it after it has cooled for a while.

〈UC18YG〉

1. Insert the plug of battery charger into the receptacle

WARNING:Do not use the electrical cord if damaged. Have it

repaired immediately.

English

20

Table 6

Rechargeable battery Temperatures at which the battery can be recharged

EB14B, EB1820L 32°F — 113°F (0°C — 45°C)

2. Insert the battery to the battery charger

Insert the battery into the battery charger as

shown in Fig. 8. Make sure it contacts the bot-

tom of the battery charger.

3. Charging

䡬 When the battery is connected to the battery charger, charging will commence and the

pilot lamp will light on.

NOTE: If the pilot lamp dose not light, pull out the plug from the receptacle and check if the

battery is properly mounted.

䡬 In approx. 50 min., when the battery is fully charged, the pilot lamp will go out.

NOTE: The battery charging time becomes longer when a temperature is low or the voltage

of the power source is too low.

When the pilot lamp does not go off even if more than four hour has passed after start

of the charging, stop the charging and contact your HITACHI AUTHORIZED SERVICE

CENTER.

䡬 Regarding the temperature of the rechargeable battery.

The temperatures for rechargeable batteries are as shown in the table below, and

batteries that have become hot should be cooled for a while before being recharged.

BEFORE USE

Check the work area to make sure that it is clear of debris and clutter.

Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.

Battery (EB1820L)

Pilot lamp

Battery (EB14B)

Fig. 8

La page charge ...

HTC ds 14dmr Manuel utilisateur

Ce manuel convient également à

HTC ds 14dmr Manuel utilisateur

dans d''autres langues

Autres documents