LG LG 32LH500D Manuel utilisateur

OWNER’S MANUAL

Safety and Reference

Please read this manual carefully before operating your

set and retain it for future reference.

LED TV*

* LG LED TV applies LCD screen with LED backlights.

www.lg.com

P/NO : COV33592901

Printed in Poland

32LH500D

32LH501C

43LH500T

43LH501C

2

ENGLISH

Safety instructions

Please read these safety precautions carefully

before using the product.

WARNING

Do not place the TV and/or remote control in the following

environments:

• A location exposed to direct sunlight

• An area with high humidity such as a bathroom

• Near any heat source such as stoves and other devices that produce

heat

• Near kitchen counters or humidiers where they can easily be

exposed to steam or oil

• An area exposed to rain or wind

• Near containers of water such as vases

Otherwise, this may result in re, electric shock, malfunction or product

deformation.

Do not place the product where it might be exposed to dust. This may

cause a re hazard.

Mains Plug is the TV connecting/disconnecting device to AC mains

electric supply. This plug must remain readily attached and operable

when TV is in use.

Do not touch the power plug with wet hands. Additionally, if the cord

pin is wet or covered with dust, dry the power plug completely or wipe

dust o. You may be electrocuted due to excess moisture.

Make sure to connect Mains cable to compliant AC mains socket with

Grounded earth pin. (Except for devices which are not grounded on

earth.) Otherwise possibility you may be electrocuted or injured.

Insert power cable plug completely into wall socket otherwise if not

secured completely into socket, re ignition may break out.

Ensure the power cord does not come into contact with hot objects such

as a heater. This may cause a re or an electric shock hazard.

Do not place a heavy object, or the product itself, on power cables.

Otherwise, this may result in re or electric shock.

Bend antenna cable between inside and outside building to prevent

rain from owing in. This may cause water damaged inside the Product

and could give an electric shock.

When mounting TV onto wall make sure to neatly install and isolate

cabling from rear of TV as to not create possibility of electric shock /

re hazard.

Do not plug too many electrical devices into a single multiple electrical

outlet. Otherwise, this may result in re due to over-heating.

Do not drop the product or let it fall over when connecting external

devices. Otherwise, this may result in injury or damage to the product.

ENGLISH

3

Desiccant

Keep the anti-moisture packing material or vinyl packing out of the

reach of children. Anti-moisture material is harmful if swallowed. If

swallowed by mistake, force the patient to vomit and visit the nearest

hospital. Additionally, vinyl packing can cause suocation. Keep it out

of the reach of children.

Do not let your children climb or cling onto the TV.

Otherwise, the TV may fall over, which may cause serious injury.

Dispose of used batteries carefully to ensure that a small child does not

consume them. Please seek Doctor- Medical Attention immediately if

child consumes batteries.

Do not insert any metal objects/conductors (like a metal chopstick/

cutlery/screwdriver) between power cable plug and input Wall Socket

while it is connected to the input terminal on the wall. Additionally,

do not touch the power cable right after plugging into the wall input

terminal. You may be electrocuted. (Depending on model)

Do not put or store inammable substances near the product. There is a

danger of combustion/explosion or re due to careless handling of the

inammable substances.

Do not drop metallic objects such as coins, hair pins, chopsticks or wire

into the product, or inammable objects such as paper and matches.

Children must pay particular attention. Electrical shock, re or injury

can occur. If a foreign object is dropped into the product, unplug the

power cord and contact the service centre.

Do not spray water on the product or scrub with an inammable

substance (thinner or benzene). Fire or electric shock accident can occur.

Do not allow any impact, shock or any objects to fall into the unit,

and do not drop anything onto the screen. You may be injured or the

product can be damaged.

Never touch this product or antenna during a thunder or lighting storm.

You may be electrocuted.

Never touch the wall outlet when there is leakage of gas, open the

windows and ventilate. It may cause a re or a burn by a spark.

Do not disassemble, repair or modify the product at your own

discretion. Fire or electric shock accident can occur.

Contact the service centre for check, calibration or repair.

If any of the following occur, unplug the product immediately and

contact your local service centre.

• The product has been impacted by shock

• The product has been damaged

• Foreign objects have entered the product

• The product produced smoke or a strange smell

This may result in re or electric shock.

Unplug the TV from AC mains wall socket if you do not intend to use the

TV for a long period of time. Accumulated dust can cause re hazard

and insulation deterioration can cause electric leakage/shock/re.

4

ENGLISH

Apparatus shall not be exposed to dripping or splashing and no objects

lled with liquids, such as vases, shall be placed on the apparatus.

Do not install this product on a wall if it could be exposed to oil or oil

mist. This may damage the product and cause it to fall.

If water enters or comes into contact with TV, AC adapter or power

cord please disconnect the power cord and contact service centre

immediately. Otherwise ,this may result in electric shock or re.

Only use an authorized AC adapter and power cord approved by

LG Electronics. Otherwise, this may result in re, electric shock,

malfunction or product deformation.

Never Disassemble the AC adapter or power cord.

This may result in re or electric shock.

Be careful in handling the adapter to prevent any external shocks to it.

An external shock may cause damage to the adapter.

CAUTION

Install the product where no radio wave occurs.

There should be enough distance between an outside antenna and

power lines to keep the former from touching the latter even when the

antenna falls. This may cause an electric shock.

Do not install the product on places such as unstable shelves or inclined

surfaces. Also avoid places where there is vibration or where the

product cannot be fully supported. Otherwise, the product may fall or

ip over, which may cause injury or damage to the product.

If you install the TV on a stand, you need to take actions to prevent the

product from overturning. Otherwise, the product may fall over, which

may cause injury.

If you intend to mount the product to a wall, attach VESA standard

mounting interface (optional parts) to the back of the product. When

you install the set to use the wall mounting bracket (optional parts), x

it carefully so as not to drop.

Only use the attachments / accessories specied by the manufacturer.

When installing the antenna, consult with a qualied service

technician. If not installed by a qualied technician, this may create a

re hazard or an electric shock hazard.

We recommend that you maintain a distance of at least 2 to 7 times

the diagonal screen size when watching TV. If you watch TV for a long

period of time, this may cause blurred vision.

Only use the specied type of battery. This could cause damage to the

remote control.

Do not mix new batteries with old batteries. This may cause the

batteries to overheat and leak.

ENGLISH

5

Batteries should not be exposed to excessive heat. For example, keep

away from direct Sunlight , open replace and electric heaters.

Do not place non-rechargeable batteries in charging device.

Make sure there are no objects between the remote control and its

sensor.

Signal from Remote Control can be interrupted due to external/internal

lighting eg Sunlight, uorescent lighting. If this occurs turn o lighting

or darken viewing area.

When connecting external devices such as video game consoles, make

sure the connecting cables are long enough. Otherwise, the product

may fall over, which may cause injury or damage the product.

Do not turn the product On/O by plugging-in or unplugging the power

plug to the wall outlet. (Do not use the power plug for switch.) It may

cause mechanical failure or could give an electric shock.

Please follow the installation instructions below to prevent the product

from overheating.

• The distance between the product and the wall should be more

than 10cm.

• Do not install the product in a place with no ventilation (e.g., on a

bookshelf or in a cupboard).

• Do not install the product on a carpet or cushion.

• Make sure the air vent is not blocked by a tablecloth or curtain.

Otherwise, this may result in re.

Take care not to touch the ventilation openings when watching the TV

for long periods as the ventilation openings may become hot. This does

not aect the operation or performance of the product.

Periodically examine the cord of your appliance, and if its appearance

indicates damage or deterioration, unplug it, discontinue use of the

appliance, and have the cord replaced with an exact replacement part

by an authorized servicer.

Prevent dust collecting on the power plug pins or outlet. This may cause

a re hazard.

Protect the power cord from physical or mechanical abuse, such as

being twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the cord

exits the appliance.

Do not press strongly upon the panel with a hand or sharp object such

as nail, pencil or pen, or make a scratch on it, as it may causedamage

to screen.

Avoid touching the screen or holding your nger(s) against it for long

periods of time. Doing so may produce some temporary or permanent

distortion/damage to screen.

When cleaning the product and its components, unplug the power

rst and wipe it with a soft cloth. Applying excessive force may cause

scratches or discolouration. Do not spray with water or wipe with a wet

cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,

benzene, alcohol etc., which can damage the product and its panel.

Otherwise, this may result in re, electric shock or product damage

(deformation, corrosion or breakage).

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn o this unit

by SWITCH.

6

ENGLISH

When unplugging the cable, grab the plug and unplug it, by pulling

at the plug.

Don’t pull at the cord to unplug the power cord from the power board,

as this could be hazardous.

When moving the product, make sure you turn the power o rst. Then,

unplug the power cables, antenna cables and all connecting cables.

The TV set or power cord may be damaged, which may create a re

hazard or cause electric shock.

When moving or unpacking the product, work in pairs because the

product is heavy. Otherwise, this may result in injury.

Contact the service centre once a year to clean the internal parts of the

product.

Accumulated dust can cause mechanical failure.

Refer all servicing to qualied service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power

supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

If the product feels cold to the touch, there may be a small “icker”

when it is turned on. This is normal, there is nothing wrong with

product.

The panel is a high technology display product with resolution of two

million to six million pixels. You may see tiny black dots and/or brightly

coloured dots (red, blue or green) at a size of 1ppm on the panel. This

does not indicate a malfunction and does not aect the performance

and reliability of the product.

This phenomenon also occurs in third-party products and is not subject

to exchange or refund.

You may nd dierent brightness and color of the panel depending on

your viewing position(left/right/top/down).

This phenomenon occurs due to the characteristic of the panel. It is not

related with the product performance, and it is not malfunction.

Displaying a still image for a prolonged time may cause image sticking.

Avoid displaying a xed image on the TV screen for a long period of

time.

Generated sound

“Cracking” noise: A cracking noise that occurs when watching or turning

o the TV is generated by plastic thermal contraction due to tempera-

ture and humidity. This noise is common for products where thermal

deformation is required. Electrical circuit humming/panel buzzing:

A low level noise is generated from a high-speed switching circuit,

which supplies a large amount of current to operate a product. It varies

depending on the product.

This generated sound does not aect the performance and reliability

of the product.

Do not use high voltage electrical goods near the TV(e.g. electric

mosquito-swatter). This may result in product malfunction.

ENGLISH

7

Preparing

NOTE

• If the TV is turned on for the rst time after it was shipped from the

factory, initialization of the TV may take a few minutes.

• Image shown may dier from your TV.

• Your TV’s OSD (On Screen Display) may dier slightly from that

shown in this manual.

• The available menus and options may dier from the input source

or product model that you are using.

• New features may be added to this TV in the future.

• The TV can be placed in standby mode in order to reduce the power

consumption. And the TV should be turned o if it will not be

watched for some time, as this will reduce energy consumption.

• The energy consumed during use can be signicantly reduced

if the level of brightness of the picture is reduced, and this will

reduce the overall running cost.

• The items supplied with your product may vary depending on the

model.

• Product specications or contents of this manual may be changed

without prior notice due to upgrade of product functions.

• For an optimal connection, HDMI cables and USB devices should

have bezels less than 10 mm thick and 18 mm width. Use an

extension cable that supports USB 2.0 if the USB cable or USB

memory stick does not t into your TV’s USB port.

A

B

A

B

*A

<

=

10 mm

*B

<

=

18 mm

• Use a certied cable with the HDMI logo attached.

• If you do not use a certied HDMI

cable, the screen may not display

or a connection error may occur. (Recommended HDMI

Cable Types)

- High-Speed HDMI®/

TM

Cable (3m or less)

- High-Speed HDMI®/

TM

Cable with Ethernet (3m or less)

CAUTION

• Do not use any unapproved items to ensure the safety and product

life span.

• Any damage or injuries caused by using unapproved items are not

covered by the warranty.

• Some models have a thin lm attached on to the screen and this

must not be removed.

• When attaching the stand to the TV set, place the screen facing

down on a cushioned table or at surface to protect the screen

from scratches.

• Make sure that the screws are fastened completely. (If they are

not fastened securely enough, the TV may tilt forward after being

installed.) Do not use too much force and over tighten the screws;

otherwise screw may be damaged and not tighten correctly.

Maintenance

Cleaning your TV

Clean your TV regularly to keep the best performance and to extend the

product lifespan.

• Make sure to turn the power o and disconnect the power cord and

all other cables rst.

• When the TV is left unattended and unused for a long time,

disconnect the power cord from the wall outlet to prevent possible

damage from lightning or power surges.

Screen, frame, cabinet and stand

To remove dust or light dirt, wipe the surface with a dry, clean, and

soft cloth.

To remove major dirt, wipe the surface with a soft cloth dampened in

clean water or a diluted mild detergent. Then wipe immediately with

a dry cloth.

• Avoid touching the screen at all times, as this may result in damage

to the screen.

• Do not push, rub, or hit the screen surface with your ngernail or a

sharp object, as this may result in scratches and image distortions.

• Do not use any chemicals as this may damage the product.

• Do not spray liquid onto the surface. If water enters the TV, it may

result in re, electric shock, or malfunction.

Power cord

Remove the accumulated dust or dirt on the power cord regularly.

8

ENGLISH

Lifting and moving the TV

Please note the following advice to prevent the TV from being scratched

or damaged and for safe transportation regardless of its type and size.

• It is recommended to move the TV in the box or packing material

that the TV originally came in.

• Before moving or lifting the TV, disconnect the power cord and

all cables.

• When holding the TV, the screen should face away from you to

avoid damage.

• Hold the top and bottom of the TV frame rmly. Make sure not to

hold the transparent part, speaker, or speaker grill area.

• When transporting a large TV, there should be at least 2 people.

• When transporting the TV by hand, hold the TV as shown in the

following illustration.

• When transporting the TV, do not expose the TV to jolts or

excessive vibration.

• When transporting the TV, keep the TV upright, never turn the TV

on its side or tilt towards the left or right.

• Do not apply excessive pressure to cause exing /bending of frame

chassis as it may damage screen.

• When handling the TV, be careful not to damage the protruding

joystick button.

CAUTION

• Avoid touching the screen at all times, as this may result in damage

to the screen.

• Do not move the TV by holding the cable holders, as the cable

holders may break, and injuries and damage to the TV may occur.

Turning the TV on or o

IN

Mounting on a table

(Image shown may dier from your TV.)

1 Lift and tilt the TV into its upright position on a table.

• Leave a 10 cm (minimum) space from the wall for proper

ventilation.

10 cm

2 Connect the power cord to a wall outlet.

CAUTION

• Do not place the TV near or on sources of heat, as this may result in

re or other damage.

ENGLISH

9

Securing the TV to a wall

(This feature is not available for all models.)

1 Insert and tighten the eye-bolts, or TV brackets and bolts on the

back of the TV.

• If there are bolts inserted at the eye-bolts position, remove the

bolts rst.

2 Mount the wall brackets with the bolts to the wall.

Match the location of the wall bracket and the eye-bolts on the rear

of the TV.

3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.

Make sure to keep the rope horizontal with the at surface.

CAUTION

• Make sure that children do not climb on or hang on the TV.

NOTE

• Use a platform or cabinet that is strong and large enough to

support the TV securely.

• Brackets, bolts and ropes are not provided. You can obtain

additional accessories from your local dealer.

Mounting on a wall

Attach an optional wall mount bracket at the rear of the TV carefully

and install the wall mount bracket on a solid wall perpendicular to

the oor. When you attach the TV to other building materials, please

contact qualied personnel. LG recommends that wall mounting be

performed by a qualied professional installer.

We recommend the use of LG’s wall mount bracket. LG’s wall mount

bracket is easy to move with cables connected. When you do not use

LG’s wall mount bracket, please use a wall mount bracket where the

device is adequately secured to the wall with enough space to allow

connectivity to external devices. It is advised to connect all the cables

before installing xed wall mounts.

10 cm

Make sure to use screws and wall mount bracket that meet the VESA

standard. Standard dimensions for the wall mount kits are described in

the following table.

Separate purchase(Wall mounting bracket)

Model

32LH500D

32LH501C

43LH500T

43LH501C

VESA (mm) (A x B) 100 x 100 200 x 200

Standard screw M4 M6

Number of screws 4 4

Wall mount bracket LSW140B

LSW240B

MSW240

A

B

CAUTION

• Disconnect the power rst, and then move or install the TV.

Otherwise electric shock may occur.

• Remove the stand before installing the TV on a wall mount by

performing the stand attachment in reverse.

• If you install the TV on a ceiling or slanted wall, it may fall and

result in severe injury. Use an authorised LG wall mount and

contact the local dealer or qualied personnel.

• Do not over tighten the screws as this may cause damage to the TV

and void your warranty.

• Use the screws and wall mounts that meet the VESA standard. Any

damages or injuries by misuse or using an improper accessory are

not covered by the warranty.

NOTE

• Use the screws that are listed on the VESA standard screw

specications.

• The wall mount kit includes an installation manual and necessary

parts.

• The wall mount bracket is not provided. You can obtain additional

accessories from your local dealer.

• The length of screws may dier depending on the wall mount.

Make sure to use the proper length.

• For more information, refer to the manual supplied with the wall

mount.

10

ENGLISH

Connections (notications)

Connect various external devices to the TV and switch input modes to

select an external device. For more information of external device’s

connection, refer to the manual provided with each device.

Available external devices are: HD receivers, DVD players, VCRs, audio

systems, USB storage devices, PC, gaming devices, and other external

devices.

NOTE

• The external device connection may dier from the model.

• Connect external devices to the TV regardless of the order of the

TV port.

• If you record a TV program on a DVD recorder or VCR, make sure to

connect the TV signal input cable to the TV through a DVD recorder

or VCR. For more information of recording, refer to the manual

provided with the connected device.

• Refer to the external equipment’s manual for operating

instructions.

• If you connect a gaming device to the TV, use the cable supplied

with the gaming device.

• In PC mode, there may be noise associated with the resolution,

vertical pattern, contrast or brightness. If noise is present, change

the PC output to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the PICTURE

menu until the picture is clear.

• In PC mode, some resolution settings may not work properly

depending on the graphics card.

Antenna connection

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

• Use a signal splitter to use more than 2 TVs.

• If the image quality is poor, install a signal amplier properly to

improve the image quality.

• If the image quality is poor with an antenna connected, try to

realign the antenna in the correct direction.

• An antenna cable and converter are not supplied.

• Supported DTV Audio: Dolby Digital, Dolby Digital Plus, PCM.

CI module connection

View the encrypted (pay) services in digital TV mode.

• Check if the CI module is inserted into the PCMCIA card slot in the

right direction. If the module is not inserted properly, this can

cause damage to the TV and the PCMCIA card slot.

• If the TV does not display any video and audio when CI+ CAM is

connected, please contact to the Terrestrial/Cable Service Operator.

USB connection

Some USB Hubs may not work. If a USB device connected through a USB

Hub is not detected, connect it directly to the USB port on the TV.

Other connections

Connect your TV to external devices. For the best picture and audio

quality, connect the external device and the TV with the HDMI cable.

Some separate cable is not provided.

NOTE

• Supported HDMI Audio format :

Dolby Digital Plus/Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),

PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)

ENGLISH

11

Remote control

The descriptions in this manual are based on the buttons on the remote

control. Please read this manual carefully and use the TV correctly.

To replace batteries, open the battery cover, replace batteries (1.5

V AAA) matching the and ends to the label inside the

compartment, and close the battery cover. To remove the batteries,

perform the installation actions in reverse.

CAUTION

• Do not mix old and new batteries, as this may damage the remote

control.

• The remote control will not be included for all sales market.

Make sure to point the remote control toward the remote control sensor

on the TV.

INDEX

A

B

A

(POWER) Turns the TV on or o.

TV/RAD Selects Radio, TV and DTV programme.

SUBTITLE Recalls your preferred subtitle in digital mode.

RATIO Resizes an image.

AV MODE Selectcs an AV mode.

INPUT Changes the input source.

B

Number buttons Enters numbers.

LIST

Accesses the saved programme list.

Q.VIEW Returns to the previously viewed programme.

Adjusts the volume level.

FAV Accesses your favourite programme list.

GUIDE Shows programme guide.

MUTE Mutes all sounds.

Scrolls through the saved programmes.

Moves to the previous or next screen.

C

D

INDEX

1

C

TELETEXT buttons( TEXT, T.OPT)

These buttons are used for

teletext.

TIME Adjusts TELETEXT time.

SETTINGS Accesses the main menus.

Q.MENU Accesses the Quick menus.

Navigation buttons (up/down/left/right) Scrolls through

menus or options.

OK Selects menus or options and conrms your input.

BACK Returns to the previous level.

EXIT Clears on-screen displays and returns to TV viewing.

D

AD/ By pressing AD button, audio descriptions function in the

selected.

- On : Audio descriptions function will be enabled.

- Off : Audio descriptions function will be disabled.

INDEX

Changes to Teletext INDEX Page.

Control buttons ( ) Controls MY MEDIA menus

and USB.

1

Coloured buttons These access special functions in some

menus.

( : Red, : Green, : Yellow, : Blue)

12

ENGLISH

Licenses

Supported licenses may dier by model. For more information about

licenses, visit www.lg.com.

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories.

The terms HDMI and HDMI High-Denition Multimedia Interface,

and the HDMIlogo are trademarks or registered trademarks of HDMI

Licensing LLC in theUnited States and other countries.

This DivX Certied® device has passed rigorous testing to ensure it plays

DivX® video.

To play purchased DivX movies, rst register your device at vod.divx.

com. Find your registration code in the DivX VOD section of your device

setup menu.

DivX Certied® to play DivX® video up to HD 1080p, including premium

content.

DivX®, DivX Certied® and associated logos are trademarks of DivX, LLC

and are used under license.

Covered by DivX Patents 7,295,673; 7,460,668; 7,515,710; 8,656,183;

8,731,369; RE45,052; and others available at [www.divx.com/patents]

PICTURE settings

To use Energy Saving feature

SETTINGS PICTURE Energy Saving

Reduce power consumption by adjusting screen brightness.

• O : Turns o the Energy Saving mode.

• Minimum / Medium / Maximum : Applies the pre-set Energy

Saving mode.

• Screen O : Screen is turned o and only sound is played.

Press any button expect Power button on the remote control to

turn the screen back on.

To select Picture Mode

SETTINGS PICTURE Picture Mode

Select the picture mode optimized for the viewing environment or the

programme.

• Vivid : Heightens contrast, brightness and sharpness to display

vivid images.

• Standard : Displays images in standard levels of contrast,

brightness and sharpness.

• Eco : The Energy Saver feature changes settings on the TV to

reduce power consumption.

• Cinema : Displays the optimum picture for movie.

• Sport : Optimizes the video image for high and dynamic actions

by emphasizing primary colours such as white, grass, or sky blue.

• Game : Displays the optimum picture for game.

To set advanced control

SETTINGS PICTURE Picture Mode Advanced Control

Calibrates the screen for each picture mode; or adjusts picture settings

for a special screen. First select a Picture Mode of your choice.

• Dynamic Contrast : Adjusts the contrast to the optimal level.

• Dynamic Colour : Adjusts colors to make the image appear in

more natural colors.

• Gamma : Sets the gradation curve according to the output of

picture signal in relation to the input signal.

SETTINGS PICTURE Picture Mode Picture Option

• Noise Reduction : Eliminates noise in the picture.

• MPEG Noise Reduction : Eliminates noise generated while

creating digital picture signals.

• Black Level : Adjusts the brightness and contrast of the screen

to suit the black level of the input picture by using the blackness

(black level) of the screen.

• Real Cinema : Optimizes the screen for movie viewing.

To reset picture settings

SETTINGS PICTURE Picture Mode Picture Reset

Resets picture settings that the user customizes.

Each picture mode is reset. Select the picture mode you wish to reset.

ENGLISH

13

To adjust Aspect Ratio

SETTINGS PICTURE Aspect Ratio

Selects the screen aspect ratio.

• 16:9 : Resizes images to t the screen width.

• Just Scan : Displays video images in the original size without

removing parts of the edge of the image.

• In DTV, Component, HDMI, and DVI (over 720p) mode, Just Scan

is available.

• Original : When your TV receives a wide screen signal it will

automatically change to the picture format broadcasted.

• Full Wide : When TV receives the wide screen signal, it will let you

adjust the picture horizontally or vertically, in a linear proportion,

to ll the entire screen fully. 4:3 and 14:9 video is supported in full

screen without any video distortion through DTV input.

• In Analogue/DTV/AV/Scart mode, Full Wide is available.

• 4:3 : Resizes images to the previous standard 4:3.

• 14:9 : You can view a picture format of 14:9 or a general TV

programme in the 14:9 mode. The 14:9 screen is viewed in the

same way as in 4:3, but is moved up or down.

• Zoom : Resizes images to t the screen width. The top and bottom

parts of the image may be cut o.

AUDIO settings

To use Sound Mode

SETTINGS AUDIO Sound Mode

Adjusts TV audio to an optimal level according to a selected sound

mode.

• Standard : Suitable for all types of video.

• News / Music / Cinema / Sport / Game : Sets audio optimized

for a specic genre.

To select various sound eects.

SETTINGS AUDIO Sound Eect

• Treble : Controls the dominant sounds in the output.

• Bass : Controls the softer sounds in the output.

• Balance : Adjusts left/right audio balance.

• Reset : Initialize the applied eect under the Sound Eect menu.

To set Auto Volume

SETTINGS AUDIO Auto Volume

Auto Volume to On. Varying volume output from channel to channel

is automatically adjusted for convenient TV watching when clicking

through dierent programme.

To select Digital Sound Out

SETTINGS AUDIO Digital Sound Out

Selects the initial setting for digital audio output signal.

• PCM : Digital output signal is xed to PCM.

• Auto : Bypass audio raw data to digital output signal.

SETUP settings

Automatically Setting Up

Programme

SETTINGS SETUP Auto Tuning

Automatically tunes the programmes.

• Auto Tuning : Selects the input source to tune programmes.

1. Select Country where the TV is used. Programme settings change

depending on the country you choose.

2. Initiate Auto Tuning.

3. Select Input Source of your choice.

4. Set Auto Tuning following screen instructions.

• If Input Source is not connected properly, programme

registration may not work.

• Auto Tuning only nds programmes that are currently

broadcasting.

• If Lock System is turned on, a pop-up window will appear

asking for password.

To use Manual Tuning

SETTINGS SETUP Manual Tuning

Adjusts programmes manually and saves the results.

• Manual Tuning : Manual Tuning lets you manually tune and

arrange the stations in whatever order you desire.

• You can also adjust the Frequency(kHz) and Bandwidth(MHz).

To select Programme mode

SETTINGS SETUP Programme Mode

This function allows you to watch a tuned program in Antenna, Cable

Mode.

• Programme Mode : You can only watch programs in the selected

mode.

To set CI Information

• CI Information : This function enables you to watch some

encrypted services (pay services).

• If you remove the CI Module, you cannot watch pay services.

• CI (Common Interface) functions may not be possible depending

upon the country broadcasting circumstances.

• When the module is inserted into the CI slot, you can access the

module menu.

• To purchase a module and smart card, contact your dealer.

• When the TV is turned on after inserting a CI Module, you

may not have any sound output. The Smart Card may not be

compatible with the CI module.

14

ENGLISH

TIME settings

SETTINGS TIME

• Clock : Checks or changes the time while watching TV.

To set the TV to turn on and o

automatically

SETTINGS TIME O Time / On Time

• O Time / On Time : Sets the time to turn on or o the TV

automatically.

• To use On Time/O Time, set the current time correctly.

• Even when the On Time function is on, the TV will turn o

automatically in 120 minutes when no button is pressed within

that time.

To use Sleep Timer

SETTINGS TIME Sleep Timer

Turns o the TV after a preset number of minutes.

• Sleep Timer : Sets the length of time until the TV to turns o .

When you turn the TV o and turn it on again,the Sleep Timer

feature will be set to o .

To set Automatic Standby

SETTINGS TIME Automatic Standby

[This function is available on certain models or in certain countries only]

If you do not press any button on the TV or remote control for a certain

period, the TV will automatically switch to standby mode.

• Automatic Standby : Once the specied standby time passes,

the TV turns o automatically. Pressing any button or changing the

resolution will initialize the standby time.

• This function does not work on Store mode or while software

update

LOCK settings

To set password

SETTINGS LOCK

• Set Password : Sets or changes the TV password. The initial

password is set to ‘0000’.

• When France is selected for Country, password is not ‘0000’ but

‘1234’.

• When France is selected for Country, password cannot be set

to ‘0000’.

To set Lock System

• Lock System : Activates or deactivates the lock system.

• Parental Guidance(Only DTV) : This function operates

according to information from the broadcasting station.

Therefore if the signal has incorrect information, this function

does not operate.

• Input Block : Blocks the input sources.

OPTION settings

To select the language

SETTINGS OPTION

• Language : Selects a desired language.

• Menu Language :

Selects a language for the display text.

• Audio Language : [In Digital mode Only] Selects the desired

language when watching digital broadcasting containing several

voice languages.

• Subtitle Language : [In Digital mode Only] Use the Subtitle

function when two or more subtitle languages are broadcast.

• If subtitle data in a selected language is not broadcast, the

default language subtitle will be displayed.

• Text Language : [In Digital mode Only][This feature is

available in certain countries only.] Use the Text language

function when two or more Text languages are broadcast.

• If teletext data in a selected language is not broadcast, the

default Text language will be displayed.

• If you select the wrong local country, teletext may not appear

correctly on the screen and some problems may occur during

teletext operation.

To set the country

SETTINGS OPTION Country

• Country : TV settings are changed according to the broadcast

environment of the selected country.

• If the country setting is changed, the Auto Tuning information

screen may appear.

• In a country that Digital broadcasting regulation isn’t xed, some

DTV functions may not work depending on digital broadcasting

circumstances.

• If the country setting is set to “--”, European terrestrial digital

standard broadcasting programmes are available, but some DTV

functions may not work properly.

To select audio commentary or

subtitles

SETTINGS OPTION Disability Assistance

• Disability Assistance : Audio commentary or subtitles are

provided for those who are hard of hearing or visually impaired.

• Hard of Hearing : This function is used for the hearing

impaired. If it is set to on, the subtitle is displayed by default.

• Audio Description : This function is for the blind, and

provides explanatory audio describing the current situation in

a TV programme in addition to the basic audio. When Audio

ENGLISH

15

Description is selected On, basic audio and Audio Description

are provided only for those programmes that have Audio

Description included.

To set up My Media

SETTINGS OPTION DivX(R) VOD

• DivX(R) VOD :

• Registration : Checks DivX Reg. Code for replaying DivX

protected videos. Register at http://vod.divx.com. Use Reg. Code

to rent or purchase movies at www.divx.com/vod.

• Rented/purchased DivX les cannot be played if the DivX

Registration Code of a dierent device is used. Use only the DivX

Registration Code granted to this specic device.

• Converted les not conforming to the DivX Codec Standard may

not play or may produce abnormal sound.

• Deregistration : Deregisters DivX.

To set Subtitle

SETTINGS OPTION Subtitle

• Subtitle : Sets subtitles to On, O or Auto.

• On : Enable subtitle display.

• O : Disable subtitle display.

• Auto : Subtitle display automatically.

To specify Factory Reset

SETTINGS OPTION Factory Reset

• Factory Reset : All stored information is deleted and TV settings

are reset. TV turns itself o and back on, and all settings are reset.

• When Lock System is in place, a pop-up window appears and

asks for password.

• Do not turn o the power during initialization.

To change TV mode

SETTINGS OPTION Mode Setting

Selecting the environment. Choose the setting mode you want.

• Mode Setting : Selects Home Mode or Store Mode.

• When in use in home, please select Home Mode.

• Store Mode mode is for store display.

To obtain the source code

SETTINGS OPTION Open Source Software Notice

• LGE Open Source Software Notice :

To display the open source licenses, that is contained in this

product.

To update the software

SETTINGS OPTION System info.

• System info. : Selects USB Update, OAD Update, or FW

Version. The rmware will download and install. Upon completion

of the update, your LG TV will restart.

• USB Update : Updates software via USB device.

• OAD Update : Selects On/O to update the operation software

using the OAD (Over Air Download) Update.

Automatic update mode means TV will update software

automatically, when software was downloaded completed.

• FW Version : Checks the software version and Product/Service

information.

INPUT settings

To select external input

Selects external input.

Press INPUT button or SETTINGS INPUT

My Media settings

To use My Media

SETTINGS MY MEDIA All Media / Movie List / Photo List /

Music List

Selects a le from the list. Displays the le that you choose.

Sets play related settings by checking option during disk playback.

Using a USB storage device -

warning

• If the USB storage device has a built-in auto recognition program

or uses its own driver, it may not work.

• Some USB storage devices may not work or may work incorrectly.

• Use only USB storage devices formatted with the Windows FAT32

or NTFS File System.

• For external USB HDDs, it is recommended that you use devices

with a rated voltage of less than 5 V and a rated current of less

than 500 mA.

• It is recommended that you use USB memory sticks of 32 GB or less

and USB HDDs of 2 TB or less.

• If a USB HDD with power-saving function does not work properly,

turn the power o and on. For more information, refer to the user

manual of the USB HDD.

• Data in the USB storage device can be damaged, so be sure to back

up important les to other devices. Data maintenance is the user’s

responsibility and the manufacturer is not responsible for data loss.

My Media supporting le

• Maximum data transfer rate : 20 Mbps (Mega bit per second)

• External supported subtitle formats : *.srt (SubRip),

*.smi (SAMI),*.sub (SubViewer, MicroDVD, DVDsubtitleSystem,

SubIdx(Vobsub)),*.ass/*.ssa (SubStation Alpha), *.txt (TMplayer).

• Internal supported subtitle formats : *.divx/*.avi

(XSUB generated from DivX6).

16

ENGLISH

Supported Video Formats

• Maximum: 1920 x 1080 @ 30p (only Motion JPEG 640 x 480 @ 30p)

• .asf, .wmv

[Video]VC1(WMV3, WVC1)

• .asf, .wmv, .wma

[Audio]WMA Standard

• .avi, divx

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,

XViD, H.264/AVC

[Audio] HE-AAC, LPCM, ADPCM, Dolby Digital, MPEG-1 Layer III

(MP3)

• .ts, .trp, .tp

[Video] H.264/AVC, MPEG-2

[Audio] MPEG-1 Layer III (MP3), Dolby Digital, Dolby Digital Plus,

AAC, HE-AAC

• .vob

[Video] MPEG-1, MPEG-2

[Audio] Dolby Digital, Dolby Digital Plus, DVD-LPCM

• .mp4, .mov

[Video] MPEG-4 Part2, XVID, H.264/AVC

[Audio] AAC, MPEG-1 Layer III (MP3)

• .mkv

[Video] MPEG-2, MPEG-4 Part2, H.264/AVC

[Audio] HE-AAC, Dolby Digital, MPEG-1 Layer III (MP3), LPCM

• .mpg, .mpeg

[Video] MPEG-1, MPEG-2

[Audio] Dolby Digital, LPCM

• dat

[Video] MPEG-1

[Audio] MPEG-2

• .v

[Video] Sorenson H.263, H.264/AVC

[Audio] MP3, AAC

Supported Audio Formats

• .mp3

[Bit rate] 32Kbps - 320Kbps

[Sample freq.] 16kHz - 48kHz

[Audio codec] MPEG1 Layer3, MPEG2 Layer3, MPEG2.5 Layer3

Supported Photo Formats

• .jpeg

[SOF0] Baseline

[SOF1] Extend Sequential

[SOF2] Progressive

[Photo size] Minimum: 64 x 64

Maximum:

Normal Type: 15360(W) x 8640(H)

Progressive Type: 1024(W) x 768(H)

Open source software

notice information

To obtain the source code under GPL, LGPL, MPL, and other open source

licenses, that is contained in this product, please visit http://opensource.

lge.com.

In addition to the source code, all referred license terms, warranty

disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM

for a charge covering the cost of performing such distribution (such

as the cost of media, shipping, and handling) upon email request to

[email protected]om. This oer is valid for three (3) years from the date

on which you purchased the product.

External control device

setup

To obtain the external control device setup information, please visit

ww w.lg.com.

Troubleshooting

Cannot control the TV with the remote control.

• Check the remote control sensor on the product and try again.

• Check if there is any obstacle between the product and the remote

control.

• Check if the batteries are still working and properly installed (

to , to ).

No image display and no sound is produced.

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other

products.

The TV turns o suddenly.

• Check the power control settings. The power supply may be

interrupted.

• Check if the Automatic Standby / Sleep Timer / Off Time is

activated in the TIME settings.

• If there is no signal while the TV is on, the TV will turn o

automatically after 15 minutes of inactivity.

When connecting to the PC (HDMI), ‘No signal’ or ‘Invalid Format’ is

displayed.

• Turn the TV o/on using the remote control.

• Reconnect the HDMI cable.

• Restart the PC with the TV on.

ENGLISH

17

Specications

CI Module (W x H x D) 100.0 mm x 55.0 mm x 5.0 mm

Environment condition

Operating Temperature 0 °C to 40 °C

Operating Humidity Less than 80 %

Storage Temperature -20 °C to 60 °C

Storage Humidity Less than 85 %

Digital TV Analogue TV

Television system

DVB-T/T2/C ,

PAL/SECAM B/G/I/D/K ,

SECAM L/L’

Programme coverage VHF, UHF

VHF: E2 to E12

UHF : E21 to E69

CATV: S1 to S20

HYPER: S21 to S47

Maximum number of

storable programmes

6,000 1,500

External antenna impedance 75 Ω

18

ENGLISH

HDMI-DTV supported mode

Resolution

Horizontal

Frequency (kHz)

Vertical

Frequency

(Hz)

640 x 480p

31.47

31.50

59.94

60.00

720(1440) x 480i

15.73

15.75

59.94

60.00

720 x 480p

31.47

31.50

59.94

60.00

720(1440) x 576i 15.63 50.00

720 x 576p 31.25 50.00

1280 x 720p

44.96

45.00

37.50

59.94

60.00

50.00

1920 x 1080i

33.72

33.75

28.13

59.94

60.00

50.00

1920 x 1080p

67.43

67.50

56.25

26.97

27.00

33.72

33.75

59.94

60.00

50.00

23.976

24.00

29.97

30.00

HDMI-PC supported mode

Resolution

Horizontal

Frequency (kHz)

Vertical

Frequency (Hz)

720 x 400 31.469 70.08

640 x 480 31.469 59.94

800 x 600 37.879 60.31

1024 x 768 48.363 60.00

1280 x 720 45.00 60.00

1360 x 768 47.712 60.015

1366 x 768 47.712 59.79

1280 x 1024 63.981 60.020

1920 x 1080 67.50 60.00

1

2

1

: Only 32LH500D / 32LH501C

2

: Only 43LH500T / 43LH501C

Component port connecting

information

Component ports on the TV Y P

B

P

R

Video output ports on

DVD player

Y P

B

P

R

Y B-Y R-Y

Y Cb Cr

Y Pb Pr

Signal Component

480i / 576i O

480p / 576p O

720p / 1080i O

1080p

O

(Only 50 Hz / 60 Hz)

Resolution

Horizontal

Frequency (kHz)

Vertical

Frequency (Hz)

720 (1440) x 480i

15.73

15.75

59.94

60.00

720 x 480p

31.47

31.50

59.94

60.00

720 (1440) x 576i 15.63 50.00

720 x 576p 31.25 50.00

1280 x 720p

44.96

45.00

37.50

59.94

60.00

50.00

ENGLISH

19

1920 x 1080i

33.72

33.75

28.13

59.94

60.00

50.00

1920 x 1080p

67.43

67.50

56.25

59.94

60.00

50.00

La page charge ...

LG LG 32LH500D Manuel utilisateur

Ce manuel convient également à

LG LG 32LH500D Manuel utilisateur

dans d''autres langues